Hirsh Industries Cabinet Lock Replacement and Wheel Assembly Instructions

Brand: Hirsh Industries

Model: Cabinet Lock Replacement and Wheel

Type: Assembly Instructions

Wing Clips

Lock Cam

Figure 1

Figure 4

Figure 3

Wing Clip

Notches

Figure 2

Note: Do not place your ngers behind or slide

your ngers along the sheet metal edges.

To replace the lock in your le cabinet you

must rst remove the old lock.

To remove the old lock:

1. Open the drawer and locate the Wing Clips

which hold the lock in place. (Figure 1)

2. With a athead screwdriver push the Wing

Clips toward the lock body and push the lock

body forward until the Wing Clip on that side is

slightly protruding out of the drawer front.

3. Again using the athead screwdriver push

the Wing Clip on the other side toward the lock

body and push forward until the lock can be

removed from the drawer.

To install the new lock:

1. Make sure that the cam is in the unlocked

position by turning the key counterclockwise

as far as it will go.

2. Feed the lock cam through the hole in the

dawer front so the Lock Cam is pointing

toward the center of the drawer (Figure 2) and

align the Wing Clips with the notches in the

drawer front (Figure 3).

3. Push the lock into the drawer front until the

Wing Clips pass through the drawer front and

snap into place behind the drawer front (Figure

4).

Lock Replacement Instructions

SHEET 1 OF 1

3636 Westown Parkway, West Des Moines, Iowa www.hirshindustries.com 1-800-383-7414

HANGING FOLDER SUPPORT INSTALLATION

This ﬁling cabinet can be used with hanging ﬁle folders by simply

installing two folder supports per drawer as follows:

Step 1: Slide the drawer half way out of the

cabinet to allow access to the drawer sides.

Identify the two small square tabs on each

side of the drawer near the front. (See

Figure 1).

Step 2: From the outside of the drawer,

push the tabs inward until they are at

a 90 degree angle to the drawer side. (See

Figure 2).

Step 3: Install one folder support into each

drawer side through the top holes and then

through the square tab. (See Figure 2).

Note: After the installation of the support,

the bend in the support should remain

above the top of the drawer and should

point toward the center of the drawer.

Step 4: Place several hanging folders in the

drawer to ensure proper support positioning.

Step 5: Repeat steps 1-4 for each drawer.

Square Tab

Step 1

Figure 1

Step 2

Step 3

Figure 2

Bend

West Des Moines, Iowa www.hirshindustries.com 1-800-383-7414

No. 18900 09/2012

BEFORE YOU BEGIN

Open, identify, and count all parts prior to assembly.

(2) Front Caster

(2) Rear Caster

(8) Screw

(2) Caster Bracket

Caster Kit Assembly Instructions

STEP 1 - Attach Front Casters:

Align screw holes in front caster mounting plate

with the screw holes in the bottom of cabinet.

Connect the Front Casters (A) with Screws (C)

using a phillips screwdriver. Fully tighten all screws.

STEP 2 - Attach Rear Casters:

Position v-bends of Caster Bracket (D) up under cabinet rims.

Align screw holes in rear caster mounting plate with screw

holes in Caster Bracket (D) ensuring the mounting plate

covers the bottom corner of the cabinet. (Figure 4)

Connect the Rear Caster (B) and the Caster Bracket (D) with

Screws (C) using a phillips screwdriver. Fully tighten all

screws.

mounting plate

rim

v-bend

Screw (C)

FIGURE 3: Complete assembly. FIGURE 4: Close-up of rear caster assembly.

www.hirshindustries.com 800.383.7414

11/06/2013

rear casters

front casters

Hirsh Industries Cabinet Lock Replacement and Wheel Assembly Instructions

Brand: Hirsh Industries

Model: Cabinet Lock Replacement and Wheel

Type: Assembly Instructions

Download PDF

report

Hirsh Industries Cabinet Lock Replacement and Wheel Assembly Instructions

Hirsh Industries Cabinet Lock Replacement and Wheel Assembly Instructions

Other documents