Whalen BC5PCHD
The “Beecham 5 Piece Counter Height Dining Set” is a quality furniture piece featuring a table and four chairs. The table top is attached to four sturdy legs with large lock washers for extra stability. The chairs have comfortable cushions and supportive backrests. All assembly hardware is included.
Whalen BC5PCHD
The “Beecham 5 Piece Counter Height Dining Set” is a quality furniture piece featuring a table and four chairs. The table top is attached to four sturdy legs with large lock washers for extra stability. The chairs have comfortable cushions and supportive backrests. All assembly hardware is included.
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Whalen Furniture Mfg. Inc. Factory No. 15160 Page 1
Beecham 5 Piece Counter Height Dining Set
Model #BC5PCHD
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, do not return this item
to the store where it was purchased. Please call our customer service number and have your
instructions and parts list ready to provide the model name, part name or factory number:
1-866-942-5362 8:30 a.m. - 4:30 p.m. PST, Monday - Friday
Or visit our website 24 hours a day, 7 days a week for product assistance at
www.whalenstyle.com
Or e-mail your request to [email protected]
LOT NUMBER:
DATE PURCHASED: / /
Model # BC5PCHD
Please call for replacement parts or assistance:
1-866-942-5362
Page 2 Factory No. 15160 Whalen Furniture Mfg. Inc.
QUALITY GUARANTEE
We are confident that you will be delighted with your Whalen Furniture purchase.
Should this product be defective in workmanship or materials or fail under normal use, we will
repair or replace it for up to 1 year from date of purchase. Every Whalen Furniture product is
designed to meet your highest expectations. We guarantee that you will immediately see the value of
our fine furniture.
This warranty gives you specific legal rights and you may also have other rights which vary from
State to State.
Customer Service: 1-866-942-5362
8:30 a.m. - 4:30 p.m. PST Monday to Friday
www.whalenstyle.com
MANUFACTURER: Whalen Furniture Mfg., Inc.
CATALOG: Beecham 5 Piece Counter Height Dining Set (BC5PCHD)
DATE OF MANUFACTURE: May 2010
MADE IN THAILAND
MAXIMUM LOAD 400 LBS (181.4 kg)
MAXI MUM LOAD 300 LBS (136.1 kg)
1. Please read the Assembly Instructions prior to assembling the unit.
2. To avoid damage, assemble the unit on a sturdy, level and non-abrasive surface.
3. Keep all hardware part out of reach of children.
4. Please wait until all steps are completed before fully tightening bolts.
5. Make sure all bolts & screws are tightly fastened before the unit is used.
GENERAL INFORMATION, TIPS & TRICKS
This unit is intended for use only with the maximum weights
indicated. Use with loads heavier than the maximum weights indicated may result in
instability causing possible injury.
Model # BC5PCHD
Please call for replacement parts or assistance:
1-866-942-5362
Whalen Furniture Mfg. Inc. Factory No. 15160 Page 3
Parts and Hardware List
Please read completely through the instructions and verify that all parts listed are present before
beginning assembly.
A- Table Top (1) B- Table Leg (4)
C- Backrest (4) D- Cushion (4) E- Front Leg Assembly (4)
F- Side Rail (8) G- Left Side Stretcher (4) H- Right Side Stretcher (4)
(1) – M6 x 50 mm (24+1 extra) (2) – M8 x 75 mm Bolt (8+1 extra)
(3) – M4 x 32 mm Screw (4) – M4 x 38 mm Screw (5) – Small Flat Washer (6) – Large Lock Washer
(16+1 extra) (16+1 extra) (24+1 extra) (8+1 extra)
(7) – Large Flat Washer (8+1 extra) M4 Allen Wrench (1) M5 Allen Wrench (1)
Tools required: M4/M5 Allen Wrench (provided), Phillips Screwdriver (not provided).
Model # BC5PCHD
Please call for replacement parts or assistance:
1-866-942-5362
Page 4 Factory No. 15160 Whalen Furniture Mfg. Inc.
Assembly Instructions for Table
1. Unpack the unit and confirm that you have all the hardware and required parts listed.
2. Place the Table Top (A) upside down on a level & protective surface as shown in detail #1.
3. Attach 4 Table Legs (B) to the apron corners of Top Panel (A) using eight M8 x 75mm Bolts (2) with
Large Lock Washers & Flat Washers (6 & 7) through the corner block into the threaded inserts in the
Leg. Tightly fasten the bolts with M5 Allen Wrench provided. See detail #1.
4. Stand the unit upright.
Hardware Required Sketch Qty.
(2) – M8 x 75mm Bolt (8)
(6) – Large Lock Washer (8)
(7) – Large Flat Washer (8)
Tools required: M5 Allen Wrench
Model # BC5PCHD
Please call for replacement parts or assistance:
1-866-942-5362
Whalen Furniture Mfg. Inc. Factory No. 15160 Page 5
Assembly Instructions for Chair
5. Lay the Backrest (C) on a level and protective surface with the threaded inserts facing up.
6. Attach Side Rails (F) onto the Backrest (C) in place with the end wood dowel fully inserted into the
hole without threaded inserts. Make sure the pre-drilled slant holes face inward. Insert and secure the
M6 x 50 mm Bolts (1) with Small Flat Washers (5) through the slant holes into the threaded inserts
included on the Backrest. Loosely tighten the bolts with M4 Allen Wrench provided. See detail #2.
7. Fully insert the tenon of Left & Right Side Stretcher (G & H) into the mortises on the Backrest (C)
properly. Make sure the Arrow UP stickers are facing in and the slant screw holes on the stretchers will
face floor after assembly. Insert and screw the M4 x 38 mm Screws (4) into the pre-drilled holes
underneath the stretcher. Loosely tighten with Phillips Screwdriver. See detail #2.
8. Repeat the procedure to attach the Front Leg Assembly (E) at the opposite end. See detail #2A.
Note: DO NOT fully tighten all the screws & bolts until the chair been adjust & level all the legs so that
they do not wobble. Once adjusted then go back and tighten while making sure that the unit remains level.
Hardware required Sketch Qty.
(1)- M6 x 50 mm Bolt (6)
(4)- M4 x 38 mm Screw (4)
(5)- Small Flat Washer (6)
Tools required: M4 Allen Wrench, Phillips Screwdriver
Model # BC5PCHD
Please call for replacement parts or assistance:
1-866-942-5362
Page 6 Factory No. 15160 Whalen Furniture Mfg. Inc.
Assembly Instructions for Chair
9. Stand assembled chair upright on a flat surface. Press down Side Rails (F) to even all legs. Now tightly
fasten all the Bolts and Screws.
10. Flip last assembly upside down and attach to the bottom of Cushion (D), secure with four M4 x 32 mm
Screws (3) through the pre-drilled holes on Front Leg Assembly (E) and Side Rails (F). Tighten with
Phillips screwdriver. See detail #3.
11. Stand the chair upright.
12. Repeat the procedure to assemble the other Chairs.
Hardware required Sketch Qty.
(3)- M4 x 32 mm Screw (4)
Tools required:
Phillips Screwdriver
Model # BC5PCHD
Please call for replacement parts or assistance:
1-866-942-5362
Whalen Furniture Mfg. Inc. Factory No. 15160 Page 7
Care and Maintenance
z Use a soft, clean cloth that will not scratch the surface when dusting.
z Use of furniture polish is not necessary. Should you choose to use polish, test first in an
inconspicuous area.
z Using solvents of any kind on your furniture may damage the finish.
z Never use water to clean your furniture as it may cause damage to the finish.
z Always use coasters under beverage glasses and flowerpots.
z Liquid spills should be removed immediately. Using a soft clean cloth, blot the spill gently. Avoid
rubbing.
z Always use protective pads under hot dishes and plates. Heat can cause chemical changes that
may create spotting within the furniture finish.
z Stains or marks from crayons or ink markers will be difficult to remove.
z In the event that your furniture is stained or otherwise damaged during use, we recommend that
you call a professional to repair your furniture.
Further advice about wood furniture care
It is best to keep your furniture in a climate controlled environment. Extreme temperature and
humidity changes can cause warping, shrinking and splitting of wood. It is advised to keep furniture
away from direct sunlight as may damage the finish.
Proper care and cleaning at home will extend the life of your purchase. Following these important
and helpful tips will enhance your furniture as it ages.
We hope you enjoy your purchase for many years.
Thank you for your purchase.
IF YOU REQUIRED TO ORDER PARTS PLEASE USE THE LIST BELOW
Beecham 5 Piece Counter Height Dining Set (BC5PCHD)
*BC5PCHD-1-TT Table Top
*BC5PCHD-10-M8x75B
M8 x 75 mm Bolt
*BC5PCHD-2-TL Table Leg
*BC5PCHD-11-M4x38S
M4 x 38mm Screw
*BC5PCHD-3-CB Chair Backrest
*BC5PCHD-12-M4x32S
M4 x 32mm Screw
*BC5PCHD-4-C Cushion *BC5PCHD-13-LLW Large Lock Washer
*BC5PCHD-5-FLA Front Leg Assembly *BC5PCHD-14-LFW Large Flat Washer
*BC5PCHD-6-SR Side Rail *BC5PCHD-15-SFW Small Flat Washer
*BC5PCHD-7-LSS Left Side Stretcher *BC5PCHD-16-M4AW M4 Allen Wrench
*BC5PCHD-8-RSS Right Side Stretcher *BC5PCHD-17-M5AW M5 Allen Wrench
*BC5PCHD-9-M6x50B
M6 x 50mm Bolt *BC5PCHD-18-CH Complete Hardware
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Whalen BC5PCHD
The “Beecham 5 Piece Counter Height Dining Set” is a quality furniture piece featuring a table and four chairs. The table top is attached to four sturdy legs with large lock washers for extra stability. The chairs have comfortable cushions and supportive backrests. All assembly hardware is included.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Outdoor Interiors 10030 Operating instructions
-
Furniture of America IDF-4914GY-S Installation guide
-
ROOMS TO GO 43844073 Assembly Instructions
-
-
Cambridge Casual HD-180035T Installation guide
-
Home Decorators Collection 9415500860 Installation guide
-
DIRECT WICKER MOD-1122 Operating instructions
-
Hampton Bay FG-MDL18TBL Operating instructions
-
-
Hooker 638-85091 Assembly Instructions
