Kichler 10798NILED User manual

Brand: Kichler

Model: 10798NILED

Type: User manual

WARNING:

• This ﬁxture is intended for installation in accordance with the

National Electric Code (NEC) and all local code speciﬁcations.

• Supply wires are not intended for use through or concealed

behind walls, ﬂoors, or ceilings.

DIMMING: This LED ﬁxture is compatible with electronic low

voltage dimmers only.

CAUTION – RISK OF SHOCK –

Disconnect Power at the main circuit breaker panel or main fuse

box before starting and during the installation.

1) Assemble mounting screws to backpan using hexnut.

2) At the center of the backpan are knockout slots. Remove

the set that matches your outlet box.

3) Position the backplate over the outlet box. Secure the

backpan to the outlet box using mounting strap screws

provided (these are the shorter of the two screws)

4) Mark the location of the outer keyhole slots of the backplate

to the wall. Be sure to mark only the narrow part of the

keyhole slot. Remove the backplate from the wall. Drill the

holes using an appropriately sized drill bit. Insert the pro

vided anchors into the holes.

5) Grounding instructions: (See Illus. A or B).

A) On ﬁxtures where mounting strap is provided with a

hole and two raised dimples. Wrap ground wire from

outlet box around green ground screw, and thread into

hole.

B) On ﬁxtures where a cupped washer is provided. Attach

ground wire from outlet box under cupped washer and

green ground screw, and thread into mounting strap.

If ﬁxture is provided with ground wire. Connect ﬁxture

ground wire to outlet box ground wire with wire connector

(not provided.) after following the above steps. Never connect

ground wire to black or white power supply wires.

6) Make wire connections (connectors not provided). Reference

chart below for correct connections and wire accordingly.

7) Carefully push wire connections back into outlet box making

sure all connections remain secure.

8) Secure the backpan to the outlet box with the mounting

strap screws.

9) Anchor the backpan to the wall using the set of holes at

each end of ﬁxture using the provided wood screws and

plastic anchors.

10) Slip the holes of the faceplate over mounting screws and

backpan.

11) Secure faceplate to backpan using lockwashers and lock-up

knobs.

12) Carefully lower each diffuser and rest onto the bottom tabs

of the side brackets.

Connect Black or

Red Supply Wire to:

Connect

White Supply Wire to:

Black White

*Parallel cord (round & smooth) *Parallel cord (square & ridged)

Clear, Brown, Gold or Black

without tracer

Clear, Brown, Gold or Black

with tracer

Insulated wire (other than green)

with copper conductor

Insulated wire (other than green)

with silver conductor

*Note: When parallel wires (SPT I & SPT II)

are used. The neutral wire is square shaped

or ridged and the other wire will be round in

shape or smooth (see illus.)

Neutral Wire

Date Issued: 12/14/16 IS-10798LED-US

GREEN GROUND

SCREW

CUPPED

WASHER

OUTLET BOX

GROUND

FIXTURE

GROUND

DIMPLES

WIRE CONNECTOR

OUTLET BOX

GROUND

GREEN GROUND

SCREW

FIXTURE

GROUND

We’re here to help 866-558-5706

Hrs: M-F 9am to 5pm EST

SEE OTHER SIDE FOR SPANISH TRANSLATIONS.

VEA EL OTRO LADO DE TRADUCCIONES AL ESPAÑOL.

This device complies with part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not

cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause un-

desired operation.

Note: This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable pro-

tection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the in-

structions, may cause harmful interference to radio communica-

tions. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can

be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of

the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for

help.

DIFFUSER

LED MODULE

OUTLET BOX

WIRE

CONNECTORS

MOUNTING PLATE

MOUNTING SCREW(S)

HEXNUT(S)

10798LED (USE FOR 10799LED & 10800LED)

FACE PLATE

Page is loading ...

WARNING:

• This ﬁxture is intended for installation in accordance with the

National Electric Code (NEC) and all local code speciﬁcations.

• Supply wires are not intended for use through or concealed

behind walls, ﬂoors, or ceilings.

DIMMING: This LED ﬁxture is compatible with electronic low

voltage dimmers only.

CAUTION – RISK OF SHOCK –

Disconnect Power at the main circuit breaker panel or main fuse

box before starting and during the installation.

1) Assemble mounting screws to backpan using hexnut.

2) At the center of the backpan are knockout slots. Remove

the set that matches your outlet box.

3) Position the backplate over the outlet box. Secure the

backpan to the outlet box using mounting strap screws

provided (these are the shorter of the two screws)

4) Mark the location of the outer keyhole slots of the backplate

to the wall. Be sure to mark only the narrow part of the

keyhole slot. Remove the backplate from the wall. Drill the

holes using an appropriately sized drill bit. Insert the

provided anchors into the holes.

5) Connect ﬁxture ground wire to outlet box ground wire with

wire connector. Never connect ground wire to black or white

power supply wire.

6) Make wire connections (connectors not provided). Reference

chart below for correct connections and wire accordingly.

7) Carefully push wire connections back into outlet box making

sure all connections remain secure.

8) Secure the backpan to the outlet box with the mounting

strap screws.

9) Anchor the backpan to the wall using the set of holes at

each end of ﬁxture using the provided wood screws and

plastic anchors.

10) Slip the holes of the faceplate over mounting screws and

backpan.

11) Secure faceplate to backpan using lockwashers and lock-up

knobs.

12) Carefully lower each diffuser and rest onto the bottom tabs

of the side brackets.

Connect Black or

Red Supply Wire to:

Connect

White Supply Wire to:

Black White

*Parallel cord (round & smooth) *Parallel cord (square & ridged)

Clear, Brown, Gold or Black

without tracer

Clear, Brown, Gold or Black

with tracer

Insulated wire (other than green)

with copper conductor

Insulated wire (other than green)

with silver conductor

*Note: When parallel wires (SPT I & SPT II)

are used. The neutral wire is square shaped

or ridged and the other wire will be round in

shape or smooth (see illus.)

Neutral Wire

Date Issued: 12/14/16 IS-10798LED-CB

INSTRUCTIONS

For Assembling and Installing Fixtures in Canada

Pour L’assemblage et L’installation Au Canada

We’re here to help 866-558-5706

Hrs: M-F 9am to 5pm EST

SEE OTHER SIDE FOR CANADIAN FRENCH TRANS-

LATIONS.

VOIR L’AUTRE CÔTÉ POUR LES CANADIENS TRA-

DUCTIONS EN FRANÇAIS.