Cerio OW-200N2-X User guide

Brand
Cerio
Model
OW-200N2-X
Type
User guide

This manual is also suitable for

Cerio OW-200N2-X is a powerful wireless networking device designed for outdoor use, operating on the 5GHz frequency band with a high output power of 500mW. It features two N-type connectors for connecting external antennas, allowing you to customize your setup for optimal signal strength and range. The device supports various operational modes, including AP mode for creating a wireless network, WDS mode for bridging multiple access points, and Client Bridge + Repeater AP mode for extending the range of an existing network.

Cerio OW-200N2-X is a powerful wireless networking device designed for outdoor use, operating on the 5GHz frequency band with a high output power of 500mW. It features two N-type connectors for connecting external antennas, allowing you to customize your setup for optimal signal strength and range. The device supports various operational modes, including AP mode for creating a wireless network, WDS mode for bridging multiple access points, and Client Bridge + Repeater AP mode for extending the range of an existing network.

eXtreme Power 11Na 5Ghz 2x2 Outdoor Series ( 500mW)
OW-200N2-X
2 N-type Connectors
OW-215N2-X
2x2 Built-in Antennas
Mounting
OW-215N2-X (Built–in 5GHz) 2x2 15 dBi directional panel
antennas
OW-200N2-X 2x2 N-Type External Antenna Connectors
Bandwidth of up to 300Mbps (TxRx link rate)
Two Weatherproof Protected Ethernet Ports ( 1x PoE-In Port
& 1x PoE-Bridge Port)
Die-Cast Aluminum Weatherproof Housing (IP67/68)
Supports 4 Operational Modes
Supports Overload Current protection and Built-in lightning
arrester (15kV ESD)
Supports PoE Bridge Capabilities for IP Cam, AP, etc.
CenOS 3.0
Grounding Port
LAN2 (PoE Bridge)
LAN1 (PoE-In)
N-Type Connector
For External Antennas
*Ethernet Ports utilize Weatherproof
protective design
2x2 Built-In 15dBi
Directional Panel Antennas
Mounting
Operation Modes : AP Mode, WDS Mode, Client Bridge +
Repeater AP Mode and WISP Repeater + AP Mode
500mW at 5Ghz Output High Power
Supports 8 Multiple-BSSID and IEEE802.1d Spanning Tree
Supports Static Routing and RIP and OSPF Dynamic
Routing through CPE mode.
QoS(Quality of Service) for bandwidth management and
traffic prioritization
Supports IGMP v1/v2/v3 snooping, Web management and
SNMP MIB-II
Software interface allows for communicating with CWMS
Software and CERIO AM-Series AP Management WLAN
Switch or Access Controller of network management
servers.
Mounting
OW-2XXN2-X wireless solutions are ideal for environments where line-of-sight obstacles
obstruct device connections. CERIO OW-2XXN2-X series can be deployed as an AP Bridge
through WDS Mode to expand connections across difficult terrain.
WDS Bridge WDS Bridge
5Ghz 5Ghz
5Ghz5Ghz
Mounting
OW-2XXN2-X wireless devices are perfect for
providing network coverage across large
environments where cables cannot be
installed.
DC Adapter PoE Injector
PoE In PoE Out
PoE Bridge
OW-2XXN2-X PoE Bridge function allows
each AP to provide power to subsequent
devices.
PoE Devices Include:
(Access Points, IP Cams, VoIP, Access Security)
Mounting
Environmental testing for bandwidth validation
CERIO’s OW-2XXN2-X 5Ghz Outdoor AP series undergoes
extensive environmental testing to ensure quality
connection and data rate stability.
We have conducted data rate tests at distances of up to
35km using our OW-200N2-X paired with our 5Ghz
outdoor directional antennas.
Our outdoor wireless testing proves to be a very valuable
reference tool for users planning on deploying our
products in a variety of outdoor environments. (Examples:
Remote mountainous areas, long distance network
extensions, long distance backhaul, remote surveillance
centers)
Mounting
Wall Mounting Pole Mounting
CERIO’s OW-PKTB Adjustable Wall / Pole Mounting Bracket Set is designed to be compatible
with OW-2XXN2-X Series mounting. Users can securely mount up to 3 devices (Access Points,
IP Cameras, External Antennas) per OW-PKTB bracket, making OW-2XXN2-X + OW-PKTB the
ideal solution for outdoor wireless deployment.
Mounting
Cerio’s OW-2XXN2-X Supports 4 Operation Modes. The default operation
mode for this device is Pure AP Mode.
CenOS 3.0
Cerio’s CenOS 3.0 Software allows each OW-2XXN2-X
device to broadcast 8 SSIDs. Each SSID can be
configured to a specified SSID by the network
administrator. This is known as VLAN tagging.
VLAN tagging effectively marks packets with a VLAN
ID to properly determine which VLAN the packet
belongs to. This allows users to deploy multiple VLANs
(Guest/VIP) on a port, and distinguish which network
each packet belongs to.
CenOS 3.0
Create and manage up to 8 ESSIDs to segment you network. This allows administrators to
separate traffic within VLANs, allowing for more organized network construction.
CenOS 3.0
Quality of Service allows for bandwidth
control which permits Administrators to
allocate bandwidth to parties as they
see fit
QoS also allows for Rule setting
customization, where admins can
enact QoS Rules to specific individual
IP Addresses, Segments, MAC
addressed, and even Ports.
CenOS 3.0
OW-2XXN2-X’s CenOS 3.0 Time Policy function allows for management of usage time
within a network. CenOS 3.0’s easy to use interface allows for simple configuration of
Day/Time restrictions that administrators can place on users within the network.
Wi-Fi RF Signal on/ off By scheduling control
CenOS 3.0
Administrators can activate the CenOS 3.0 Auto Reboot function that effectively reboots the
network system routinely based on admin settings. This enables better system reliably and a
lower likelihood of crashes. It also reduces the need for constant on-site system
maintenance in case of system crashes. This setting is ideal for Hotel deployment.
CenOS 3.0
CenOS 3.0 provides a Traffic Monitor and Graphical GUI Status Interface.
CenOS 3.0
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19

Cerio OW-200N2-X User guide

Brand
Cerio
Model
OW-200N2-X
Type
User guide
This manual is also suitable for

Cerio OW-200N2-X is a powerful wireless networking device designed for outdoor use, operating on the 5GHz frequency band with a high output power of 500mW. It features two N-type connectors for connecting external antennas, allowing you to customize your setup for optimal signal strength and range. The device supports various operational modes, including AP mode for creating a wireless network, WDS mode for bridging multiple access points, and Client Bridge + Repeater AP mode for extending the range of an existing network.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents