Znewtech Digital Column Bathroom Scale User manual

Brand: Znewtech

Model: Digital Column Bathroom Scale

Type: User manual

Digital Column Bathroom Scale

User Manual

Z

Z N E W T E C H

LCD Display

Stand Pole

Stand Pole

Stand Base

Screws

Pole Connector

Wire Connectors

1

2

7

3

4

5

6

8

Scale Platform

Getting to know your Znewtech Scale

1

Step-by-Step Assembly Instructions

Required Tool:

Philips screwdriver (not included)

Parts Listing:

A

Scale Base (1 Unit)

Stand poles (2 Units)

B

C

Display (1 Unit)

D

Pole Connector (1 Unit)

E

Screws (6 Units)

Assembly will take 10-20 minutes

2

Lay down all the parts on the floor as shown below

Single screw hole ends

Both single screw holes need to face down

1

Two screw holes ends

3

Connect a stand pole with the stand base

2

Align the two screw holes on the stand pole

with the two slots on the stand base, and push

the stand pole into the stand base firmly.

Run the wire from stand base through a stand pole

4

Connect a stand pole with the scale display

The single screw hole faces down

3

Run the wire from scale display through a stand pole

Align the two screw holes on the stand pole

with the two slots on the display, and push

the stand pole into the display firmly.

5

Insert the pole connector and connect two wires

4

Align the slot on the pole connector

with the screw hole on the stand

pole , and push the pole connector

into the stand pole firmly

Connect the two wires

together

6

Connect two stand poles together

5

Push the stand pole into

the pole connector firmly

7

Install batteries

6

Install 4 AAA batteries into the

battery compartment on the

bottom of scale platform

8

Finish assembly

7

Hold up the scale to

stand-up position and

fasten all 6 screws

Use the scale on a hard, level and even surface (no carpeting).

Inconsistent and soft surfaces will cause inaccurate measurements.

Troubleshooting

How to reset the scale?

1) Uninstall batteries

2) Wait for one hour

3) Reinstall batteries

Screw

Screw

Screw

Screw

Screw

Screw

Need Help?

support@znewtech.com

9

1. Press the Unit Set Switch located on the back of the scale LCD Display to select the unit

(kg/lb/st) that you want to set. The stone (st) is a unit of measure equal to 14 pounds (lb)

avoirdupois, or 6.3503 kilograms (kg).

2. The unit changes each time the set switch is pressed.

Setting Units

Unit Set Switch

10

Measuring Your Weight

1. Place the scale on the hard and flat surface.

2. Step on the scale platform, the scale stand pole can be tilted forward up to 15°. Remain

still and the scale will count up to your weight. The display will flash twice when the

weight is locked.

3. Your weight will be displayed for about 10 seconds, and then the scale turns off

automatically.

11

The “LO” indicates the battery power is

low. Please change new batteries.

The “Err” indicates overload.

Maintenance

Warranty

One-Year Limited Warranty

Contact us for questions or returns:

support@znewtech.com

Capacity: 440 lbs (200 kg)

Weight Increments: 0.2 lbs (100 g)

Switch-on Over: 3kg / 6lbs

Power Source: 4 AAA batteries

Unit Modes: kg/lb/st

Platform Size: 12" x 12" (31 cm x 31 cm)

Scale Height: 40 " (100 cm)

Low Battery and Overload Indication

Specifications

Support

Please visit our website www.znewtech.com

for more information about the product.

Contact us at support@znewtech.com.

12

1
2
3
4
5
6
7
8
9
10
11
12
13

Znewtech Digital Column Bathroom Scale User manual

Brand: Znewtech

Model: Digital Column Bathroom Scale

Type: User manual

Other documents