Eneo DPR-2016/500D Operating Instructions Manual

Operating Instructions

Digital Video Recorder

Models: DPR-2016/500D

3

DPR-2016/500D

Safety instructions

EMC class

This video recorder (DVR) is a class A device in accordance with EN 55022.

This device may cause interference to other equipment in domestic use. In such cases the persons opera-

ting the DVR are required to provide appropriate countermeasures, for which they themselves bear the cost.

►

Importance of these Operating Instructions

Please read the safety instructions and the other information contained in the Operating Instructions before

connecting up and operating the DVR.

The Operating Instructions should be kept in a safe place for later reference.

►

Ambient conditions for the DVR

The DVR should be protected against excessive heat, dust, damp and vibration.

The DVR may only be operated at temperatures between +5°C and +40°C, and up to a maximum air

humidity of 90%.

The DVR may only be operated indoors, and must be protected against incursion of water and damp.

►

Care of the DVR

Never switch on the DVR when damp has penetrated it. In such cases, have the DVR checked by a qualied

service engineer.

Do not place any heavy objects on the DVR.

Never cover over the DVR's vents.

Never insert metal objects or any other items into the vents. This may permanently damage the DVR.

The housing may only be opened by authorised persons. Repairs may only be carried out by qualied

service personnel.

The DVR must be disconnected from the power supply before its housing is opened.

►

Getting started with the DVR

When laying the connecting cables, make sure no weight is placed on them, that they are not kinked or

damaged, and that no damp can penetrate them.

►

Cleaning the DVR

The housing of the DVR may only be cleaned with a damp (not wet) cloth,

Use only a mild detergent. Do not use solvent-containing detergents or petrol. This could permanently

damage the surface nish.

►

Spare parts

Use only original spare parts from Videor Technical GmbH.►

5

DPR-2016/500D

Table of contents

Overview 7

Package contents

7

Basic functions

7

Features

7

Requirements for operation

7

Control options

7

Connections on the rear

8

Front panel controls 1

0

Key to controls 1

2

Function buttons 1

2

PTZ camera functions 1

2

Playback functions 1

2

Remote control functions 1

3

Playback functions 1

3

Menu overview 1

4

Accessing the menus 1

6

Accessing the Display menu 1

6

Accessing the PTZ menu 1

6

Accessing the Setup menu 1

7

Accessing the Search menu 1

7

Getting started

18

Checklist for DVR operation 1

8

Connecting the remote control and DVR 1

8

Switching on the DVR 1

9

Switching off the DVR 1

9

Administration 2

0

Saving your system setup 2

0

Loading your system setup 2

0

Deleting recordings 2

0

Downloading software updates 2

1

Hiding from specic users 2

1

Restoring factory defaults 2

1

Changing hard disk 2

2

Fitting hard disk into an empty drive rack 2

3

Mirroring of hard disks 2

4

Determining the memory requirement of a recording 2

5

Searching for recordings 2

6

Using Bookmark search 2

8

Using calendar search 2

9

Using event log search 3

0

Using text-in search 3

1

Using motion search 3

2

Copying recordings 3

3

6

DPR-2016/500D

Table of contents

Menu descriptions – Setup menu 34

System – Information 3

5

System – Date/Time 3

6

System – Storage 3

7

System – User 3

9

System – Shutdown 4

0

System – Log out USER... 4

0

Network – Network 4

0

Network – Notication 4

3

Devices – Camera 4

4

Devices – Alarm-Out 4

5

Devices – Display 4

6

Devices – Remote Control 4

7

Record – Record 4

8

Record – Schedule 4

9

Record – Pre-Event 5

0

Record – Archive 5

1

Event – Alarm-In 5

2

Event – Motion Detection 5

4

Event – Object Detection 5

6

Event – Video Loss 5

8

Event – Video Blind 6

0

Event – Text-In 6

2

Event – System Event 6

4

Event – Event Status 6

6

WebGuard – WebWatch controls 6

7

WebGuard – WebSearch controls 6

8

Using WebGuard 6

9

Specications DPR-2016 7

0

Accessories 7

2

Supported PTZ cameras 7

3

Index 7

5

Notes on disposal 7

8

7

DPR-2016/500D

Overview

Package contents

Digital video recorder (DVR)

Mains power cord

Operating instructions

RAS (Remote Administration System) software on CD

Operating instructions for RAS software on paper and CD

Mounting kit for cabinet installation

Screws for attaching SCSI Connector

Mounting screws for installation of hard disk drives

Infrared remote control

Key for hard disk drive rack

Basic functions

Record video images using multiple cameras

Event-based recording start

Video playback

Search for specic video sequences

Features

MPEG-4 compression / pentaplex mode

16 loop-through inputs / VGA, S-VHS/FBAS outputs

Audio and alarm inputs / outputs

Max. recording speed: 400 eld images per sec (PAL)2

Memory capacity 500 GB

4 hard disks max., CD/DVD-RW writer included

Standard hard disk mirroring

Maximum video resolution 720 x 576 pixels

SCSI port for archiving / memory expansion

Integral motion detector/object tracking

ATM/POS text display / 2x to 4x digital zoom

RS-232 / RS-485 ports

Network port (Ethernet) / IR remote control

Requirements for operation

Digital video recorder DTR connected

At least 1 camera connected

At least 1 monitor connected

Mouse connected, if DVR is to be controlled by mouse

Control options

Front panel

Remote control

Mouse

WebGuard

RAS program

●

8

DPR-2016/500D

Connections on the rear

Note: Connections optionally for NTSC or PAL operation.

1 2 3 4 5 6 7

1314 12 111920 161718 15 910 8

9

DPR-2016/500D

Connections on the rear (continued)

No. Designation Functions/connections Example devices

1 VIDEO IN 1-16 Max. 16 video channels Cameras

2 LOOP 1-16 Max. 16 loop-through video channels Cameras

3 AUDIO IN 1-16 Max. 16 Audio inputs Microphone

4 AUDIO OUT Audio output Amplier, speakers

5 SPOT1 - SPOT4 Max. 4 video outputs Spot monitors

6 SVHS OUT S-VHS output Monitors

7 VIDEO OUT Video output Monitors

8

NC1 - NC4, C1 - C4,

NO1 - NO4

Relay alarm output for external device Siren, ashing light

9 VGA PC monitor PC monitor

10 SCSI External storage media Hard disk

11 AO1 - AO12 Alarm outputs for external devices Siren, ashing light

12 NETWORK Network Network cable

13

USB External interface Drive, mouse

14 ARI/GND Reset alarm with external signal Switch

15 RS-232C 2 external interfaces Modem

16 RS-485 2 external interfaces Keyboard, PTZ camera

17 Reset switch Reset to factory defaults -

18 AI1 - AI16 Alarm inputs for external devices Sensors

19 Power switch On/Off switch -

20 Power supply Mains power connection -

10

DPR-2016/500D

Front panel controls

The following diagram and table set out the controls on the front panel of the DVR:

17 15 1114 13 12

1 32 865 9 104 7

16

11

DPR-2016/500D

Front panel controls (continued)

No. Designation Function

1 Power-on indicator when DVR is in operation

2 Indicates Ethernet connection

3 Display when mirroring hard disks

4

Display when using hard disks

5 Open built-in CD/DVD-RW writer

6 Display window Status display

7

Function buttons

8 1 to 16

Select cameras

Enter passwords

●

9 Menu navigation Navigation and selection within the menu

10 Open/quit menu structure

11 Shuttle ring Innitely adjust playback speed

12 USB ports for mouse and external storage media

13

Jog dial

Change size of frame in picture-in-picture mode

Change numerical values in Setup menu

Frame-by-frame playback in Play mode

●

14

Reset alarm

View event list

●

15 Start/end panic recording

16

Playback functions (primary assignment)

PTZ camera functions (secondary assignment)

17 Hard disks max. 4 hard disks in the exchange frame

12

DPR-2016/500D

Key to controls

Function buttons

Element Function

On/Off Triplex

On/Off Audio

Dening bookmarks in Search menu by pressing and holding button

Copying recordings in Search menu by pressing and holding down button

Freeze On/Off

Change display mode

Sequence On/Off

PTZ camera functions On/Off

Zoom On/Off

Spot monitor assignments

PTZ camera functions

Element Function

Zoom in

Close-up

Wide-angle

Save preset

Load preset

Playback functions

Element Function

Start/pause playback

Select Search/Play function

Stop playback

●

Fast rewind

Fast forward

Frame-by-frame rewind

Frame-by-frame forward

13

DPR-2016/500D

Remote control functions

The following diagram and table set out the functions on the remote control:

ID

Select System ID

DISPLAY

TRIPLEX

FOCUS PRESET

SET

VIEW

ZOOM

AUDIO

CLIP COPY

BOOK MARK

FREEZE ALARM

SEQUENCE

SPOT

CAMER

A

2 3 41

1

5

9

13

2

6

10

14

3

7

11

15

4

8

12

16

MENU PTZ

ZOOM

PANIC

DIGITAL VIDEO RECORDER

Remote Controller

1

2

3

4

5

6

7

12

10

11

8

9

No. Designation Function

1

SPOT 1 - 4

Spot monitor assignments

2

Reset alarm

View event list

●

3 1 to 16

Select cameras

Enter passwords

●

4

PTZ camera functions

5 PTZ

PTZ camera functions On/Off

6 ZOOM Zoom On/Off

7

Playback functions

8 PANIC Start/end panic recording

9 Menu navigation

Navigation and selection within

the menu

10 MENU Open/quit menu structure

11

Function buttons

12

Function buttons

Playback functions

Element Function

Select Search/Play function

Stop playback

●

Pause playback

Start playback

Fast rewind

Fast forward

Frame-by-frame rewind

Frame-by-frame forward

14

DPR-2016/500D

The following illustration shows the structure of the complete menu tree that is accessible using the mouse

control:

Display Camera 1. CAM1

2. CAM2

3. CAM3

Screen Format PIP Top left

2x2 Bottom left

3x4 Top right

3x3 Bottom right

2x8 Size 1/16

1x12 Size 1/9

4x4

Previous Group

Next Group

Edit Group Camera

Spot Monitor...

Exit “Edit Group”

Sequence

Freeze

Zoom...

Audio

PTZ... Speed

Auto Pan

Tour

Pattern

Device Menu

Light

Pump

Wiper

Power

Aux.

Move to Origin

Spot Monitor ...

Exit PTZ

Spot Monitor... Select Spot Monitor

Spot Monitor 1

Spot Monitor 2

Spot Monitor 3

Spot Monitor 4

Menu overview

15

DPR-2016/500D

The following illustration shows the structure of the complete menu tree that is accessible using the mouse

control:

Setup menu... System Information

Date/Time

Storage

User

Shutdown...

Log out user1...

Network Network

Notication

Devices Camera

Alarm-Out

Display

Remote Control

Record Record

Schedule

Pre-Event

Archive

Exit Search

Menu overview (continued)

16

DPR-2016/500D

Accessing the Display menu

Requirement:

The current camera image is shown in full image or quad image.

Step Action Access using

Key sequence/menu

path

1 Open Display menu...

Device

Remote control

Mouse Display

Access to submenu via Device/Remote Control

Submenu Camera image Key sequence

Change Display modes (PIP, 2x2, 3x3, 4x4)

Without frame

....

Previous/Next Group Without frame

Edit Group With frames >

Change position of image-in-image Without frame

Change size of image-in-image Without frame Jog dial

Accessing the PTZ menu

Requirement:

A PTZ camera is connected and congured.

Current camera image is shown as a full image.

Step Action Access using Key sequence/menu path

1

Open PTZ menu...

Result: Menu of the congured PTZ

camera is shown.

Device > >

Remote control PTZ > > MENU

Mouse PTZ...

●

Accessing the menus

17

DPR-2016/500D

Accessing the Setup menu

Requirement:

The current camera image is shown in full image or quad image.

Step Action Access using

Key sequence/menu

path

1

Open Setup menu...

Result: Prompt for user name and

password.

Device

Remote control MENU

Mouse Setup menu...

2

Log in as user.

User name: admin

Password: (blank)

Note: Use default access data only for

rst-time access.

Accessing the Search menu

Requirement:

The current camera image is shown in full image or quad image.

Step Action Access using

Key sequence/menu

path

1

Open Search menu...

Result: Search for recorded images is

activated.

Device >

Remote control > MENU

Mouse Search

●

Accessing the menus, continued

18

DPR-2016/500D

Getting started

Checklist for DVR operation

Step Action Menu path

1 Connect peripheral devices as per planned setup.

2 Specify menu language. Setup menu... > System > Information

3 Adjust date and time. Setup menu... > System > Date/Time

4 Set up user. Setup menu... > System > User

5

Set up network and desired notication channels

(optional).

Setup menu... > Network > ...

6 Register peripherals with DVR. Setup menu... > Devices > ...

7 Set up event types and associated responses. Setup menu... > Event > ...

8 Set up recording parameters and schedule. Setup menu... > Record > ...

Connecting the remote control and DVR

The remote control and DVR can be assigned an ID, because the ID of each DVR in the network must be

unique. The DVR will then only respond to the remote control with the matching ID.

If the system ID in the DVR is 0, it will respond to the remote control regardless of the remote’s ID.

If the system ID in the DVR is not 0, you must set the ID of the remote control identically.

Step Action Menu path

1 Set DVR system ID. Setup menu... > System > Information

2

Match remote control to system ID by

pressing ID button on remote control.

3 Select relevant number on remote control.

●

19

DPR-2016/500D

Getting started (continued)

Switching on the DVR

Requirement:

The start-up preparations are complete.

DVR mains plug is connected.

Step Action

1 Switch on power switch.

2

Switch on monitor.

Result: System starts up automatically and is ready to use.

Switching off the DVR

Requirement:

You have accessed the Setup menu.

Step Action Menu path

1

Shut down the system.

Result: System shuts down automatically.

Setup menu > System > Shutdown ......

2 After shutdown, switch off power switch.

●

20

DPR-2016/500D

Administration

Saving your system setup

You can save your DVR’s setup data, including its network conguration.

Requirement:

USB memory stick

Step Action Menu path

1

Insert a USB memory stick into one of the USB

ports.

2 Export your setup.

Setup menu... > System > Information >

Setup Export...

3 Specify a le name.

4 Export your setup. Export

Loading your system setup

You can load your stored DVR system setup with or without its network conguration.

Requirement:

USB memory stick with stored setup

Step Action Menu path

1

Insert a USB memory stick into one of the USB

ports.

2 Import your setup.

Setup menu... > System > Information >

Setup Import...

3

Select the le name and, where appropriate, the

network conguration.

4

Import your setup. Import

Deleting recordings

You can only delete all your recordings together. It is not possible to delete recordings from a specic time

period.

Step Action Menu path

1 Delete all recordings.

Setup menu > System > Information > Clear All

Data...

or

Setup menu > System > Storage > Information tab

> Using > Clear

●

Page is loading ...

Eneo DPR-2016/500D Operating Instructions Manual

This manual is also suitable for

Eneo DPR-2016/500D Operating Instructions Manual

Related papers

Other documents