OSP Furniture DSR5454GLD Operating instructions

Brand
OSP Furniture
Model
DSR5454GLD
Type
Operating instructions
© Office Star Products May, 2023
© Office Star Products September 2020
DSR5454GLD (LF)
DISRUPTOR L-SHAPED GAMING DESK
ASSEMBLY INSTRUCTIONS
OSP FURNITURE LIMITED PRODUCT WARRANTY
Design Lab Products
• 3 years on gaming desks and chairs
• Upholstery is not warranted against routine scratching and scuffing
*All warranties are limited to the original purchaser for normal commercial usage defined as a standard forty hour work week by persons weighing 250 lbs. or
less. This warranty will not cover labor, freight or damage from misuse, abuse, negligence, alteration, accident, vandalism, rusting, acts of nature or any other
event beyond the control of Office Star Products. The warranty does not cover cosmetic damage that may result from normal use. Liability for incidental or
consequential damages is excluded. The user assumes all risk of injury resulting from use of this product. When usage is more than 40 hours per week, a two
year warranty on all parts applies. Fabric and foam is warranted for one year. This warranty gives you specific legal rights, and you may also have other rights
which vary from state to state.
It is the customer’s responsibility to prepay freight on any components returned to the factory. Return freight on components covered by warranty
will be paid by Office Star Products.
Our quality standards are among the highest in the industry. Sometimes, no matter how hard we try, there are times when parts are damaged or missing. Our
Parts Department will do everything possible to promptly remedy the problem. Contact us via e-mail parts@officestar.net, by Fax 1-909-930-5629, or toll free
parts number 1-800-950-7262, Monday through Friday 8:00 a.m. - 5:00 p.m. Pacific Time.
WARNING
1. Use this product only one person at a time.
2. Do not use this product unless all bolts screws and knobs are
securely tightened.
3. Check that all bolts screws and knobs are tight every three
months or as needed.
4. Do not overturn back tilt knob when decreasing tension.
5. Dispose of packing material properly. Do not use plastic cover as
head covering. It may cause suffocation.
6. Do not use product as a stepladder.
7. Use this product for its intended purpose only.
8. Use mild detergent only for cleaning.
IMPORTANT-PLEASE KEEP THESE INSTRUCTIONS IN CASE OF ANY CUSTOMER SERVICE ISSUES
IMPORTANT-PLEASE KEEP THESE INSTRUCTIONS IN CASE OF ANY CUSTOMER SERVICE ISSUES
© Office Star Products September 2020
DSR5454GLD (KNC)
L-SHAPED GAMING DESK
ASSEMBLY INSTRUCTIONS
OSP FURNITURE LIMITED PRODUCT WARRANTY
Design Lab Products
• 3 years on gaming desks and chairs
• Upholstery is not warranted against routine scratching and scuffing
*All
warranties are limited to the original purchaser for normal commercial usage defined as a standard forty hour work week by persons weighing 250 lbs. or
les
s. This warranty will not cover labor, freight or damage from misuse, abuse, negligence, alteration, accident, vandalism, rusting, acts of nature or any other
e
vent beyond the control of Office Star Products. The warranty does not cover cosmetic damage that may result from normal use. Liability for incidental or
consequential damages is
excluded. The user assumes all risk of injury resulting from use of this product. When usage is more than 40 hours per week, a two
y
ear warranty on all parts applies. Fabric and foam is warranted for one year. This warranty gives you specific legal rights, and you may also have other rights
which vary from state to state.
It is the customer
’s responsibility to prepay freight on any components returned to the factory. Return freight on components covered by warranty
will be paid
by Office Star Products.
Our quality standards are among the highest in the indust
ry. Sometimes, no matter how hard we try, there are times when parts are damaged or missing. Our
P
arts Department will do everything possible to promptly remedy the problem. Contact us via e-mail parts@officestar.net, by Fax 1-909-930-5629, or toll free
pa
rts number 1-800-950-7262, Monday through Friday 8:00 a.m. - 5:00 p.m. Pacific Time.
IMPORTANT-PLEASE KEEP THESE INSTRUCTIONS IN CASE OF ANY CUSTOMER SERVICE ISSUES
IMPORTANT-PLEASE KEEP THESE INSTRUCTIONS IN CASE OF ANY CUSTOMER SERVICE ISSUES
WARNING
1. Do not use this product unless all bolts screws and knobs are securely
tightened.
2. Check that all bolts screws and knobs are tight every three months or as
needed.
3. Dispose of packing material properly. Do not use plastic cover as head
covering. It may cause suffocation.
4. Do not use product as a stepladder.
5. Use this product for its intended purpose only.
6. Use mild detergent only for cleaning.
Phillips Screwdriver also needed for assembly (not provided).
HARDWARE LIST
NO DRAWING DESCRIPTION SIZE QUANTITY
AAllen Bolt 18 PCS
8 PCS
26 PCS
1 PC
13 PCS
1 PC
2 PCS
2 PCS
4 PCS
Allen Bolt
Allen Bolt
Allen Bolt
Flat Head Allen Bolt
Allen Wrench
Wood Screw
Machine Screw
Wood Screw
6 x 12 x 12mm
6 x 20 x 12mm
6 x 32 x 12mm
6 x 50 x 12mm
6 x 25 x 10mm
Ø
3.5 x 12 x 6mm
4 x 12 x 8mm
4 x 12 x 8mm
B
C
D
E
F
G
I
H
(1) Left Top Shelf (1 PC)
(3) Left Desk Top (1 PC)
(2) Right Top Shelf (1 PC)
(4) Right Desk Top (1 PC)
PARTS
PARTS
(5) Left Side Frame (1 PC)
(7) Rear Frame (2 PCS)
(9) Left Front Upper Crossbar (1 PC)
(6) Right Side Frame (1 PC)
(8) Left Rear Upper Crossbar (1 PC)
(10) Left Rear Lower Crossbar (1 PC)
(11) Rear Leg (1 PC) (12) Accessory Hook (1 PC)
(13) Cup Holder (1 PC)
(15) Power Outlet (1 PC)
(14) Wireless Charger (1 PC)
(16) Remote Control (1 PC)
STEP 1
STEP 2
PARTS
(21) Right Upper Frame (1 PC)
(20) Left Upper Frame (1 PC)
(22) Storage Tray (1 PC)
(23) Left Upper Crossbar (1 PC) (24) Right Upper Crossbar (1 PC)
(25) Middle Upper Frame (1 PC) (26) Right Front Upper Crossbar (1 PC)
(17) Right Rear Lower Crossbar (1 PC)
(19) LED Power Supply (1 PC)
(18) Right Rear Upper Crossbar (1 PC)
DSR5454GLD (KNC)
L-SHAPED GAMING DESK
ASSEMBLY INSTRUCTIONS
A
5
18
Remove all the parts from carton, separate them into part numbers indicated on the list and make sure part quantities are correct.
STEP 1 Secure Right Rear Lower Crossbar (17) between Right Side Frame (6) and Rear Leg (11) using four Allen Bolts (A). Secure Right Rear
Upper Crossbar (18) between Right Side Frame (6) and Rear Leg (11) using one Bolt (A) and one Bolt (D) for each end of Right Rear Upper Crossbar (18).
FULLY TIGHTEN ALL BOLTS. Secure Left Rear Upper Crossbar (8) to Rear Leg (11) using Allen Bolt (A) and Allen Bolt (D). Attach Left Rear Lower
Crossbar (10) to Rear Leg (11) using two Allen Bolts (A). FULLY TIGHTEN ALL BOLTS.
STEP 2 Secure Left Side Frame (5) to Left Rear Upper Crossbar (8) using one Allen Bolt (A) and secure to Rear Lower Crossbar (10) using two Allen
Bolts (A). FULLY TIGHTEN ALL BOLTS.
11 10
8
17
6
D
A
10
8
A
A
DSR5454GLD (KNC)
L-SHAPED GAMING DESK
ASSEMBLY INSTRUCTIONS
DSR5454GLD (KNC)
L-SHAPED GAMING DESK
ASSEMBLY INSTRUCTIONS
3
20
25
STEP 4
C
C
4
STEP 5
STEP 6
STEP 3 Secure Right Front Upper Crossbar (26) between Left Rear Upper Crossbar (8) using one Allen Bolt (C) and two Allen Bolts (A). FULLY TIGHTEN
ALL BOLTS. Secure Left Front Upper Crossbar (9) between Right Front Upper Crossbar (26) and Left Side Panel (5) using one Allen Bolt (C) and two Allen
Bolts (A). FULLY TIGHTEN ALL BOLTS.
STEP 4 Secure Left Upper Crossbar (20) and Middle Upper Frame (25) to Left Desk Top (3) using four Allen Bolts (C). FULLY TIGHTEN ALL BOLTS.
Secure Right Upper Frame (21) to Right Desk Top (4) using two Allen Bolts (C). FULLY TIGHTEN ALL BOLTS.
STEP 5 Secure Left Desk Top (3) to frame assembly using ten Allen Bolts (C). FULLY TIGHTEN ALL BOLTS.
STEP 6 Secure Right Desk Top (4) to frame assembly using six Allen Bolts (C). FULLY TIGHTEN ALL BOLTS.
C
C
C
3
4
21
C
26 9
C
AA
5
6
STEP 3
8
DSR5454GLD (KNC)
L-SHAPED GAMING DESK
ASSEMBLY INSTRUCTIONS
DSR5454GLD (KNC)
L-SHAPED GAMING DESK
ASSEMBLY INSTRUCTIONS
14
G12
H
STEP 7
STEP 8
STEP 9
7
STEP 10
B
STEP 7 Attach Cup Holder (13), Wireless Charger (14) and Storage Tray (22) to desk top. Secure Power Outlet (15) to desk top using two Wood
Screws (H). FULLY TIGHTEN WOOD SCREWS (H). Secure Accessory Hook (12) to Left Side Frame (5) using two Machine Screws (G). FULLY TIGHTEN
MACHINE SCREWS (G).
STEP 8 Secure Left Upper Crossbar (23) between Left Upper Frame (20) and Middle Upper Frame (25) using two Allen Bolts (A). FULLY TIGHTEN
ALL BOLTS. Secure Right Upper Crossbar (24) between Left Upper Crossbar (23) and Left Right Upper Frame (21) using two Allen Bolts (C). FULLY
TIGHTEN ALL BOLTS.
STEP 9 Secure Rear Frames (7) to assembly using four Allen Bolts (B) for each frame. FULLY TIGHTEN ALLEN BOLTS (B).
STEP 10 Secure Left Top Shelf (1) to assembly using seven Flat Head Allen Bolts (E) and two Wood Screws (I). FULLY TIGHTEN ALL
BOLTS & SCREWS.
22
13
15
A
C
A
23
24
A
B
7
1
I
E
7
5
DSR5454GLD (KNC)
L-SHAPED GAMING DESK
ASSEMBLY INSTRUCTIONS
Model Number:
STEP 11 Secure Right Top Shelf (2) to assembly using six Flat Head Allen Bolts (E) and two Wood Screws (I). FULLY TIGHTEN ALL
BOLTS & SCREWS.
STEP 12 Connect cords of Left Top Shelf (1) and Right Top Shelf (2). Connect cord of Left Top Shelf (1) to LED Power Supply (19).
Model Number: JN02-03-22K
STEP 11
STEP 12
I
2
7
E
1
2
1
19
19
WIRELESS CHARGER - SAFETY WARNINGS AND INSTRUCTIONS FOR USE
To Power ON the Wireless Charger
Your desk includes wireless charging capabilities using the wireless charger
as shown. Please carefully follow the instructions and safety warnings below
before using the wireless charger with your supported device.
Plug the USB cable from the bottom of the wireless charger into any powered USB 2.0
port, or any 5V power adapter that accepts a USB plug.
Using the Wireless Charger
To charge your device using
wireless charging, place the device
centered on the wireless charger
face and wait for the device to
indicate it has begun charging.
Using the USB Charge Port
To charge your device using USB
charging port, plug in your device’s
USB charging cord into the USB port
as shown and wait for the device to
indicate it has begun charging.
USB Port on wireless
charger will light up RED
once powered on. The
charger is now ready to use.
NOTE: The wireless charger included supports most devices with
wireless charging capabilities. Please consult your device’s OEM
instruction manual for proper wireless charging use, safety
warnings, and limitations. Stop using the wireless charger
IMMEDIATELY if your device becomes hot. Improper use of the
wireless charger, using non-compatible devices, or tampering with
the wireless charger in any way may cause device failure, damage,
or injury.
Voltage: 5V / Input: 5V/1.5A
Output (USB Port): 5V/1A
Output (Wireless): 5W Wireless
Charging Surface
USB
Charge Port
Powered USB Port
5V Power Adapter
SAFETY WARNINGS - PLEASE READ FIRST
Devices with cases
thicker than 4mm
may not allow
wireless charging.
Remove the case
from the device or
use the USB port
for wired charging
instead.
Devices with rings,
kickstands, or
finger grip
accessories will
not allow wireless
charging. Remove
the accessories or
use the USB port
for wired charging
instead.
DO NOT attempt to
wireless charge devices
with metallic cases,
metallic attachments,
or magnetic
attachments. Remove
the device from such
cases or use the USB
port for wired charging
instead.
DO NOT allow any metallic foreign
objects or liquids to come in
contact with the wireless charger.
Only devices that support wireless
charging should be put on the wireless
charger surface.
Rotate the dust cover 90 degrees
counter-clockwise to cover the USB
charging port when not in use.
DIY 1
RGBW
DIY 2DIY 3
QUICK
SLOW
AUTO
FLASHDIY 4DIY 5DIY 6
FADE7JUMP3JUMP7 FADE3
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

OSP Furniture DSR5454GLD Operating instructions

Brand
OSP Furniture
Model
DSR5454GLD
Type
Operating instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents