MULTIPLEX MII () Flex Manifold Kit Installation guide

MULTIPLEX
Brand
MULTIPLEX
Model
MII () Flex Manifold Kit
Type
Installation guide

This manual is also suitable for

In accordance with our policy of continuous product development and improvement,
this information is subject to change at any time without notice.
020000920 Revision 1 AUGUST 30, 2006
Manitowoc Beverage Equipment
2100 Future Drive Sellersburg, IN 47172-1868
Tel: 812.246.7000, 800.367.4233 Fax: 812.246.9922
www.manitowocbeverage.com
FLEX MANIFOLD FOR MII ICE/BEV SOFT PLUMBED UNITS
REPLACEMENT KIT INSTRUCTIONS For Part Numbers
020000925, 020000926
(NOTE: Instructions are the same for 4 port or 5 port Flex Manifolds. Will need one kit for each Flex Manifold to replace)
1. Turn off all water supplies that are connected to the
Ice/Beverage Dispenser
2. Turn off the CO
2
gas that connects to the dispenser’s
carbonator tank.
3. Activate a plain water beverage valve and a carbon-
ated beverage valve to relieve any pressure in the lines.
4. Disconnect the power cords supplying power to the
dispenser and the carbonator pump.
5. Remove the front splash panel to access the Flex
Manifold’s and the Merchandiser to access the valves.
6. Remove any and all line holding bars at bottom front
of foam front panel. See FIGURE 1.
7. Removing the valves, valve blocks, and dropping just
the water lines, will help with easier access to the Flex
Manifold. Syrup lines and the end (outer) valve water
lines can stay in place. See FIGURE 2
8. Unclip the Insulated Flex Manifold from its two side
brackets. See FIGURE 3.
9. Remove existing insulation cover from the Flex Mani-
fold, front. New insulation pieces are provided.
10. Remove the four (4) screws holding the Flex Manifold
to its plate. See FIGURE 4.
11. Make sure you mark the water lines going to each
valve, or keep them in line so you can replace in the
new Flex Manifold properly.
12. Pry the existing Flex Manifold away from the existing
mounting plate, using screwdriver. Take all lines out
of existing plate. Note their locations for the new plate.
13. Examine all o-rings on the existing lines, verify they
are OK. Replace any that require it.
14. Assemble the new Plate and new back base insulation
piece first. Remove adhesive backing, punch out the
holes, and align as in FIGURES 5 and 6.
Note: Pre-install the four (4) self tapping screws in
each of the plate corner holes and then remove.
This will make it easier to install.
FIGURE 1
FIGURE 2
FIGURE 3
FIGURE 4
FIGURE 5
FIGURE 6
2
020000920 Revision 1 FEBRUARY 28, 2007
Equipment Installation Instructions
15. Insert the 4 or 5 water lines properly into the new plate,
then the two (2) Supply plain water and carb water lines.
See FIGURES 7 and 8.
16. Align all the tube o-ring end grooves into the bottom of
their small keyholes. Then press the new Flex Manifold
onto these oring ends from the front of plate (opposite
side as the insulation is on). Make sure all o-rings are
fully into the Flex Manifold holes, fully seated. Then
screw Flex Manifold and Plate together with the 4 new
8-32 sheet metal screws. See FIGURE 9.
17. Assemble the new front insulation piece (remove ad-
hesive film cover) over the Flex Manifold and stick tightly
to the sides of the already installed back insulation piece.
See FIGURE 10.
18. Assemble the new back insulation piece cover (remove
adhesive film cover) over all tubes and new back base
insulation piece. See FIGURE 11.
19. Assembly the two new tubing cover pieces (remove
adhesive film cover), one for two supply water lines,
one for 4 or 5 outlet water lines. See FIGURE 11.
20. Make sure all pieces fit together and fully insulate the
Flex Manifold assembly, no air spaces.
21. Place the 4 or 5 outlet water lines into their respective
valve mounting plate holes. Assemble the valve mount-
ing plates and screw back into the mounting plate. As-
semble the removed valves back onto their mounting
plates, plug in 24VAC connectors.
22. Click the finished Flex Manifold insulated assembly, with
tubing, into its brackets.
23. Finish with any holding bars removed.
24. Turn on CO
2
then water to check for leaks.
25. Finish splash plate and merchandiser reassembly.
26. Start up system for beverage and ice dispensing.
FIGURE 7
FIGURE 8
FIGURE 9
FIGURE 10
FIGURE 11
PARTS INCLUDED IN MII-SERIES 4-PORT MANIFOLD KIT 020000925
Qty. Description Part Number
1 Manifold 4-Port Raised 020000986
4 Screw 8-32 X 5/8" Tri-Lobe 020000992
8 O-Rings, .239 5009080
4 O-Rings, .364 5009763
1 Insulation 50130995
1 Bracket Reinforced Manifold 5009782
PARTS INCLUDED IN MII-SERIES 5-PORT MANIFOLD KIT 020000926
Qty. Description Part Number
1 Manifold 5-Port Raised 020000987
4 Screw 8-32 X 5/8" Tri-Lobe 020000992
8 O-Rings, .239 5009080
4 O-Rings, .364 5009763
1 Insulation 5030995
1 Bracket Reinforced Manifold 5030994
  • Page 1 1
  • Page 2 2

MULTIPLEX MII () Flex Manifold Kit Installation guide

MULTIPLEX
Brand
MULTIPLEX
Model
MII () Flex Manifold Kit
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents