Teleco Televisore Led TY2/32 User manual

Brand: Teleco

Model: Televisore Led TY2/32

Category: LCD TVs

Type: User manual

INSTRUCTION MANUAL

TY2/32

LED TV with built in DVB-T/S2

GB-1

LED TV with built in DVB-T/S2

SAFETY INFORMATION

IMPORTANT SAFETY INSTRUCTIONS - READ CAREFULLY BEFORE USE

Take note of the following safety information which appears on the back of this TV.

AUTION! TO PREVENT ELECTRICAL SHOCK, DO NOT REMOVE ANY COVERS OR SCREWS.

NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

his symbol indicates that there are important operating and maintenance instructions in the literature

accompanying this unit.

This symbol indicates that dangerous voltage constituting a risk of electric shock is present inside this unit.

Keep these instructions

• Do not use this TV near water.

• Clean only with a slightly damp cloth.

• Do not block any ventilation openings.

• Install in accordance with the supplied Quick Start Guide and this User Guide.

• Do not install or operate near any heat sources such as radiators, stoves, or other devices that produce heat.

• Protect the power cord from being walked on or pinched, particularly at plugs, and the point where it exits

from the TV.

• Do not allow the power cord to overhang the edge of a table.

• Unplug this TV during lightning storms or when you do not intend to use it for a long period of time.

• To avoid interference, switch this TV off while operating other radio devices in the immediate vicinity.

Refer all servicing to qualified service personnel. Servicing is required when the TV has been damaged

(e.g. the power cord or plug being damaged), liquid is spilt on it, objects have fallen onto it or the TV has

been exposed to rain or moisture, does not operate normally or has been dropped.

WARNING! TO REDUCE THE RISK OF FIRE OR ELECTRICAL SHOCK, DO NOT EXPOSE THIS TV

TO RAIN OR MOISTURE. THE TV MUST NOT BE EXPOSED TO DRIPPING OR SPLASHING AND

NO OBJECTS FILLED WITH LIQUIDS SHOULD BE PLACED ON THE TV.

No naked flame sources such as candles should be placed on the TV.

User Guide

CAUTION! CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE

MANUFACTURER COULD VOID THE USER’S AUTHORITY TO OPERATE THIS

DEVICE.

CAUTION! USING CONTROLS, MAKING ADJUSTMENTS OR PERFORMING

PROCEDURES IN ANY WAY OTHER THAN AS SPECIFIED HEREIN MAY RESULT

IN HAZARDOUS EXPOSURE.

Important

This TV generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with

these instructions, may cause harmful interference to radio communication. However, this is no guarantee that

interference will not occur in a particular installation. If the TV does cause harmful interference to electrical

devices, which can be determined by turning the TV off and on, the user is encouraged to try to correct the

interference by one of the following measures:

• Re-orient or relocate the receiving antenna.

• Increase the gap separating the external device and the TV.

• Connect the external device to an outlet on a circuit different from that to which the TV is

connected.

• Consult the dealer or an experienced radio/TV technician for help.

Specifications Troubleshooting Using DVB-S2 Using TV Installing Introducing Safety Warnings

Features Features LED TV LED TV

Contents

• Safety Warnings ..................................................................................................... 1

• Contents ................................................................................................................. 2

• Chapter 1 Introducing the LED TV

Package Contents...................................................................................................... 3

LED TV Controls......................................................................................................... 4

LED TV Connections.................................................................................................. 5

Remote Control.......................................................................................................… 6

• Chapter 2 Installing the LED TV

Wall Mounting............................................................................................................. 7

Preparing your LED TV for use ….............................................................................. 8

Connecting a TV Cable or an Antenna....................................................................... 9

Connecting External Devices.................................................................................... 10

Using the CI Plus Slot................................................................................................ 12

Installation Guide Setup............................................................................................. 13

• Chapter 3 Using the TV Features

Basic Operation......................................................................................................... 14

Customising the Picture Settings............................................................................... 17

Customising the Sound Settings................................................................................ 18

Customising the Channel Settings............................................................................. 19

Customising the Feature Settings.............................................................................. 20

Customising the Setup Settings................................................................................. 22

•

Chapter 4 Using the DVB-S2 Features

S2 Basic Functions ................................................................................................... 24

Customising S2 Edit Channel Settings...................................................................... 25

Customising S2 Installation Settings......................................................................... 26

Customising S2 System Setup Settings.................................................................... 27

Customising S2 Tool Settings................................................................................... 28

Customising S2 Game and REC Settings................................................................. 29

•

Troubleshooting ...................................................................................................... 30

•

Specifications ...........................................................................…………................ 31

•

CE (EU) Certification .............................................................................................. 32

Chapter 1 Introducing the LED TV

INTRODUCTION

Thank you for purchasing this LED TV which has been designed and manufactured to give you

many years of trouble-free service.

You may already be familiar with using a similar product but please take the time to read these

instructions carefully: they have been written to ensure you get the very best from your

purchase.

Throughout the remainder of this user guide the LED TV will be referred to as the ‘TV’.

HDMI

HDMI (High Definition Multimedia Interface) is the next generation of digital interface. Unlike

conventional connections, it transmits uncompressed digital and audio signals using a single

cable. This TV supports high-definition video input via the HDMI socket on the back of the TV.

Safety First!

To ensure both your own safety and that of others, please read the Safety Information

BEFORE you operate this product.

Keep this information in a safe place for future reference.

Package Contents

Make sure the packaging contains all the following items.

IN THE BOX

You will find:

LED TV without TV Base

TV Base

User Guide

Remote Control with batteries

Car Power Supply Lead

NOTE: These items are all you need to set up and operate the LED TV in its basic

configuration. If any of the items listed are damaged or missing, please contact us.

Specifications Troubleshooting Using DVB-S2 Using TV Installing Introducing Safety Warnings

Features Features LED TV LED TV

LED TV controls

Front/Right View and Controls

LED

The LED light indicates when the LED TV is on.

Infrared Receiver

SYMBOL DESCRIPTION

STANDBY BUTTON, Turns the LED TV on / sets it to standby mode.

INPUT BUTTON, Used to select from among different input signal

sources.

MENU BUTTON, Press once to display the menu, press again to

exit the menu.

CH-/CH+ BUTTON, Used to scan up or down through the channels.

In menu mode used to select the desired sub-menu item.

VOL-/VOL+ BUTTON, Adjusts volume. Also used to select main

menu items and adjust various item settings in menu mode.

Specifications Troubleshooting Using DVB-S2 Using TV Installing Introducing Safety Warnings

Features Features LED TV LED TV

LED TV connections

Left/Right Side Bottom View and sockets

No. DESCRIPTION

1 12 V DC in Connect the DC power lead to this socket.

2 USB in Connects to USB device.

3 HDMI in Connects to devices with HDMI interface

4 PC in Connects to a PC or other devices with a VGA

interface.

5 PC AUDIO in Connects to a PC audio socket or other devices with

a VGA interface.

6 SCART in Connects to external devices with SCART socket.

This SCART input allows video/audio in + RGB +

video/audio out from an external device to be

shown on your TV.

7 Common Interface Allows a CAM (Conditional Access Module) smart

Plus (CI+) card to be inserted to access the functions in the

card.

8 Coaxial out Digital audio out (coaxial output only for TV)

9 mini AV in Connects to camcorder, VCR, DVD Player, Digital

Set-Top-Box or other A/V equipment with composite

and audio sockets/jacks.

10 mini YPBPR in Connects to the DVD Player, Digital Set-Top-Box or

other A/V equipment with component (YPBPR) video

sockets/jacks

11 RF in Connects to your RF antenna or LNB cable.

12 EARPHONES out Connects to headphones.

*you may need to readjust the volume when using

headphones.

13 IR (infrared) extender Connects to IR signal input or output device.

Specifications Troubleshooting Using DVB-S2 Using TV Installing Introducing Safety Warnings

Features Features LED TV LED TV

Remote Control

• Turns the TV on / sets it to standby

mode.

• Switches between different preset picture

modes.

• Switches between different preset sound

modes.

• Use to select and switch to a channel by

using 0-9 buttons or edit the item name in

the DVB-S2 menu.

• Press to pause, stop or delay DTV

program playback.

• Press to return to previously viewed

channel

NAVIGATION buttons

UP/DOWN/LEFT/RIGHT

• Allows you to move, select and set up

the OSD options.

• Allows you to confirm your selection in

the OSD options.

• Displays the electronic program guide in

DTV mode.

• Scrolls through the customised Favourite

Channels list

• Displays program information.

• Down-changes FAVOURITE channels.

• Goes to desired time and program.

• Searches for desired channel by channel

name. Up-changes FAVOURITE channels.

• Switches between TV and Radio in DTV

mode.

• Plays program frame by fram.

• Repeats playback during

playing of multimedia files.

• Repeats playback of segment

A-B during playing of multimedia files.

Coloured Buttons

(RED/GREEN/YELLOW/CYAN)

• Accesses Teletext items or corresponding

pages. The coloured buttons are also use

to access interactive modes when the TV is

in DTV or menu mode.

• Press to display the channel list.

• Displays your favourite sub-title in DTV .

• Selects the screen aspect mode.

• Recording Menu.

•

Auto-adjusts the picture on the TV in PC

mode.

• Mutes / restores TV sound.

• Displays current TV status, TV Channel,

input source, etc.

Switches between different audio languages

in TV/DTV mode (only applicable when the

TV program has this feature).

• Displays the TV Menu.

• Displays the DVB-S2 SETUP Menu or

exits the OSD menu.

• Selects from among different input

sources.

• Sets the TV sleep time.

• Changes the channels up and down.

• Increases/decreases volume.

• Turns Teletext function on/off.

• Toggles between different slow motion

speeds in sequence or plays program

frame by frame.

• Freezes a multi-page passage on

screen in Teletext mode.

• Plays or pauses program playing

• Goes to next page in Teletext mode.

• Stops or resumes program playing.

• Activates zoom function during media

playing.

• Goes to previous page in Teletext mode.

• Displays the main index in Teletext

mode. Goes back to previous program.

• Freezes multi-page scrolling on screen

in Teletext mode. Goes to next program.

• Shows hidden info such as quiz answers

in Teletext mode.

• Plays a program in fast rewind mode.

• Displays the sub-page on the Teletext

screen.

• Plays a program in fast forward mode.

Specifications Troubleshooting Using DVB-S2 Using TV Installing Introducing Safety Warnings

Features Features LED TV LED TV

Chapter 2 Installing the LED TV

Wall Mounting

How to remove the TV Stand

If you would prefer to mount your new TV on a wall instead of on the base, please remove the TV stand and

follow the instructions included in the wall mounting kit (not included).

Read all the instructions before proceeding with stand removal.

. Open the box, and make sure all the necessary parts are in the box. The TV is assembled with the stand.

LED TV without TV Stand arm

Four mounting holes

Size: M4 screws

How to wall mount the TV

Use four screws to mount the TV on the bracket.

This unit is VESA-compliant and designed to be wall-

mounted with a VESA-compliant 200x100mm mounting

kit. Mount this unit according to the instructions on the

wall bracket (not supplied).

a.Open the box,and make sure all necessary parts are in the box

b.Take out Five screws in the accessories bag.

c. Cover an even stable surface with a soft cloth. Place the LED TV unit screen-down on the cloth.

Screw those five screws clockwise as shown at 1

Accessories Bag

ST4x16 5Pcs

Specifications Troubleshooting Using DVB-S2 Using TV Installing Introducing Safety Warnings

Features Features LED TV LED TV

The end

Preparing your LED TV for use

How to set up the TV

Use an antenna cable to connect the RF signal to the LED TV RF IN terminal (refer to page 9).

Connect one end of the DC source unit to the back of the TV, and the other end of the DC source unit

to the power source.

Insert two AAA size batteries (supplied) in the remote control.

Step 1 Push and slide the back cover to open the

battery compartment of the remote control.

Step 2 Insert batteries. Make sure the (+) and (-) poles

of the batteries match the (+) and (-) terminals in the battery

compartment. Snap the cover back in place.

Do not clean the remote control with caustic cleaning agents (such as porcelain, stainless

steel, toilet, or oven cleaners etc.) as doing so may damage it.

Using the Remote Control properly

• Never mix used and new batteries in the device.

• Replace all the batteries in the device at the same time.

• Remove the batteries if the remote control is not to be used for an extended time period.

• To avoid faults read the following instructions and handle the remote control properly.

• Do not drop the remote control or knock/slam it against a surface.

• Do not get water or any other liquid on the remote control.

• Do not place the remote control on a wet surface.

• Do not place the remote control in direct sunlight or near sources of heat.

NOTE: Remove the batteries from the remote control handset when it is not to be used for a long period to

prevent corrosion, battery leakage or physical injury and/or property damage, including fire.

Connect another external A/V equipment (refer to page 10).

Remote control range

Your LED TV can be operated from up to 5m away when the

remote control is pointed directly at the receiver.

Specifications Troubleshooting Using DVB-S2 Using TV Installing Introducing Safety Warnings

Features Features LED TV LED TV

LED TV

Connecting a TV Cable, Antenna or Dish

For information on connection procedures refer to the owner’s manuals of any external devices.

When connecting external devices do not connect any AC power leads to mains power sockets until all other

onnections are completed.

onnecting a TV Cable or an Antenna

ntenna Connection

The antenna requirement for good colour Digital TV reception is more exacting than it is for analogue TV

reception. A good quality outdoor antenna is therefore strongly recommended.

Connecting to the TV (CATV) cable

A 75-ohm coaxial cable connector is built into the set for easy hook-up.

When connecting the 75-ohm coaxial cable to the set, connect the 75-ohm cable to the

RF IN terminal.

For best results use a high gain TV aerial, preferably roof or loft mounted.

To improve picture quality in a poor signal area, purchase and install a signal amplifier.

If the antenna needs to be split between two TVs, use a 2-Way Signal Splitter (not supplied).

Satellite Dish Connection

You can connect a fixed satellite dish or one on a motorized positioner or connect multiple fixed dishes using a

DiSEqC 1.0 switch.

RF switch

(not included)

2-way signal

splitter

(not included)

Cable

TV line

Cable TV converter /

decoder (not included)

DisEqC Switch

OUT

Specifications Troubleshooting Using DVB-S2 Using TV Installing Introducing Safety Warnings

Features Features LED TV LED TV

Connecting External Devices

ottom Side View of TV

ight Side View of TV

Mass Storage Device

VGA AUDIO cable

VGA Cable

HDMI Cable

A/V EQUIPMENT

Left Side View of TV

SCART Cable

GAMES CONSOLE

VIDEO CAMERA

HEADPHONES

VCR

mini AV Cable DVD PLAYER

mini component Cable

TV CABLE BOX

Satellite antenna cable

SATELLITE RECEIVER

Mass Storage Device

AV RECEIVER

MIR DEVICE

Specifications Troubleshooting Using DVB-S2 Using TV Installing Introducing Safety Warnings

Features Features LED TV LED TV

Connecting External Devices

Connecting A/V Equipment with an HDMI Connector

• This TV accepts HDMI (High-Definition Multimedia Interface).

• This TV SET supports the HDCP (High-Bandwidth Digital Content Protection) Protocol for the TV set modes

(

480p, 576p, 720p, 1080i etc.).

•

When you connect to the output of an HD-ready player (DVD Player, Set-Top-Box or PC) switch to the HDMI

function: the TV will automatically detect the resolution used by the HDMI source.

• To get the best picture quality, adjust the output resolution of the DVD Player or Set-Top-Box to 720p.

se an HDMI cable to connect the A/V equipment HDMI output socket to the LED TV HDMI input socket.

The HDMI connector provides both video and audio signals. Therefore, it is not

necessary to connect the audio cables.

Connecting a PC

Use a VGA cable to connect the VGA output socket on the PC to the PC IN socket on the LED TV. Use an audio

cable to connect the audio output sockets on the PC to the PC AUDIO IN sockets on the LED TV.

The best resolution for this TV is as follows:

1920 pixels (horizontal) x 1080 pixels (vertical)

If the PC is set to auto-idle after a set time, then the TV may also enter standby mode due to

no input signal being detected.

To avoid this happening you will need to configure the PC.

Proceed as follows.

1. Click Start on the computer desktop screen.

2. Select Control Panel.

3. Click twice on Power Options and select Never from the Turn off Monitor drop-down box.

4. Then, again on the Control Panel, click twice on Display, then select the Screen Saver tab

and select None from the screen saver drop-down box.

This will prevent the TV from going to Standby mode.

Connecting an A/V Equipment with a miniComponent(YPBPR)/miniComposite

Connector

Use a minicomponent/minicomposite cable to connect the external component/video output sockets on the A/V

equipment to the miniYPBPR IN/miniAV IN sockets on the LED TV. Use a miniAV cable to connect the external

audio sockets on the A/V equipment to the miniAV sockets on the LED TV.

The video component sockets on your A/V equipment are sometimes labelled YPbPr or YCbCr.

For an explanation of video component, see your A/V equipment user’s guide.

Not all A/V devices can be connected to a TV via the Composite connector. Please check your A/V

equipment user’s guide for compatibility.

Connecting an A/V Equipment with SCART Connector

Use a Scart cable to connect the SCART socket on the external A/V equipment to the SCART IN socket on the

LED TV.

Specifications Troubleshooting Using DVB-S2 Using TV Installing Introducing Safety Warnings

Features Features LED TV LED TV

How to connect a CI (Common Interface) plus card

ARD FACE FRONT

NOTE: The Conditional Access Module

(CAM) does not come with the TV set.

It can only be obtained when you subscribe to service providers

like PayTV or other service providers

When you use the CI plus slot for the first time there may be a

dummy card already inside it; if so, remove it and then insert the

CAM.

CI (Common Interface) slot

Allows the Conditional Access Module

(CAM) smart card to be inserted to

access the encrypted content.

Using the CI Plus Slot

To view DVB-T or DVB-S2 encrypted (pay to view ) services in digital TV

mode.

• INSERTING THE CAM CARD

Insert the CAM card into the DVB-T or DVB-S2 slot in the direction indicated

by the arrow until it fits in place; the card face (label) must face forwards.

CAM label

Make sure the CAM label

faces front.

CAM (Conditional Access

Module) Smart card

• REMOVING THE CAM CARD

To remove the CAM card just pull it out of the slot.

This function enables you to watch selected encrypted (pay) services of certain channels. Please switch

off your TV, read the instructions provided with the CAM and ensure it is inserted correctly before

switching the TV on again.

Press the INPUT button on the remote control to display the Input source menu, and use the

UP/DOWN buttons to select DVB-T or DVB-S2.

Specifications Troubleshooting Using DVB-S2 Using TV Installing Introducing Safety Warnings

Features Features LED TV LED TV

Installation Guide Setup

hen you switch on the TV for first time, the DVB-T Auto Installation menu appears on the screen.

Press to select Home Mode and press GREEN to go to the Next Page to select the Country,

Language and Auto Power Off settings; lastly, select the Auto Search type to start the tuning program.

You can press EXIT to quit the screen or

press RED to go to the Previous Page to

re-select the previous setting.

DVB-T (Digital Video Broadcasting - Terrestrial)

Before you begin using your DVB-T TV please note the following:

1. Your existing aerial may not be suitable for receiving Digital signals.

2. Your existing aerial may not be pointing in the correct direction.

3. Your house may be located in an area where Digital TV reception is poor.

The above factors may prevent you from receiving some or all of the Freeview Channels.

In the event of difficulty please contact a qualified aerial installation engineer for assistance.

Do not adjust your TV set as it is not faulty.

Never agree to have work done by anyone who calls without an appointment and does not show ID and/or credentials.

Re-Tune

If you experience a loss of one or more channels please re-scan. Service providers sometimes alter program

locations without prior notice. Please retune the TV before calling for technical assistance.

{ Press the INPUT button on the remote control to display the source list. Use the UP/DOWN buttons to select

other sources you wish to watch and press the OK button.

If the LED TV is not to be used for some length of time always disconnect it from the power

source. The STANDBY button on the top panel is only used to switch the LED TV to standby,

it does not disconnect the device from the power supply.

To disconnect from the power supply remove the DC plug from the bottom i/o board of the TV set.

Specifications Troubleshooting Using DVB-S2 Using TV Installing Introducing Safety Warnings

Features Features LED TV LED TV

Chapter 3 Using the TV Features

Basic operation

Selecting the input source

Selecting an input signal source

You can select an input signal source by pressing the INPUT button on the TV control panel: press it

and the onscreen display menu shows the diagram illustrated below. Then press the CH+/CH- buttons

n the control panel or the UP/DOWN buttons on your remote control to choose an input signal source.

If your audio and video devices are connected to your TV you can choose from the following input signal

sources:

Adjusting volume

• When you press VOL+/VOL- to increase/decrease volume the diagram below appears on your

screen for 5 seconds.

• The MUTE symbol appears in a corner of the screen when you press the MUTE button; press the

MUTE button again and the symbol disappears.

• To restore sound press either the MUTE button or the VOL+ button. The indicator below shows the

sound level.

Channel/favourites list:

Lets you customise the Channel/Favourite List under ATV/DTV Operation. Press the LIST/FAV button to

display the Channel List/Favourite List; use the UP/DOWN button to highlight and select the channel

you wish to watch. Press OK button to confirm.

Before any customisation can be effected, the Favourite List must be preset in the favourite

management menu.

Specifications Troubleshooting Using DVB-S2 Using TV Installing Introducing Safety Warnings

Features Features LED TV LED TV

Customising TV Operation

Basic TV operation

Program Guide MENU (only available in DVB-T):

llows you to customise the Program Guide menu.

Press the EPG button to display the Electronic Program Guide information menu.

se the NAVIGATION buttons to highlight an individual EPG item.

Press the UP/DOWN buttons to select an item.

Press the RED button to activate the Weekly or Daily view.

Press the YELLOW or BLUE button to view Previous Day or Next Day.

Reminder

Press GREEN to start creating a viewing or recording plan; press once only for viewing and twice for

recording. If the standby mode has timed out, 2 minutes are needed before reactivation and

background recording will start without powering the panel. To watch the program it is necessary to

press STANDBY.

Info (Display)

Press INFO to view in extended mode.

*Note: Automatic record when EPG reminder timer is active when a USB device is present.

*Programs may change without notice. Always check schedules on the day of broadcast.

TimeShift (available in DVB-T mode):

Allows a program to be recorded and the program being recorded to be played at the same time. This

function is only available when you connect a USB device and set Timeshift Buffer on the PVR/Timeshift

menu. Press TIMESHIFT to start timeshift-recording a program when continuous viewing is interrupted and

you wish to resume viewing later. When playback resumes you can use PAUSE/PLAY/FF/FB/PREV/NEXT

normally, use a pop-up virtual keypad bar or press STOP to return to normal mode. Alternatively, you can

press the PAUSE button to start Timeshift when no menu is highlighted and press it again to resume the

process. If, during the recording process, the signal fades/disappears, the recording process will pause until

the

signal re-stabilises.

Specifications Troubleshooting Using DVB-S2 Using TV Installing Introducing Safety Warnings

Features Features LED TV LED TV

Basic TV operation

electing the Media Source

If a USB device is connected you can select the Media source from the input menu.

Photo/Music/Movie/e-Book playback

Press the LEFT/RIGHT button to toggle among the Photo, Music, Movie, and e-Book browsers. Select the

SB disk and partition. Four different patterns are available to handle these four types of media content. The

system automatically classifies files, showing only the corresponding supported files.

Note: the USB interface supports *.mpg/*.dat/*.vob/*.avi/*.mp3/*.jpg/*.bmp/*.png/*.txt file types etc.

*Note: large image files may be slow to appear on the screen.

File Browser screen

Allows user to delete or add/del all files to/from a playlist via the RED or GREEN button.

Allows user to show selected file information on the right of the screen.

Allows user to press NAVIGATION and OK buttons to tick folders and files to be played back on the list.

Allows user to press the PLAY button to play back the file on the list.

Allows the user to press the EXIT button and then LEFT/RIGHT to switch between thumbnails and list mode on the Photo explorer

screen.

File Playback screen

Allows user to display a virtual keypad for various tasks that are unavailable on the remote control.

Press ENTER to pop it up and EXIT to hide it; alternatively, it will be displayed in the bottom right part of the screen in music playing

screen or none of the above when reading an e-Book.

Press the RED button to add or delete a bookmark, press the GREEN button to go to a desired page, press the YELLOW button to

pop up a Bookmark list, press BLUE to pop up Playlists and press FB or FF to page up or page down in e-Book mode.

Same as PLAY/PAUSE button on the remote control: press to resume playback or pause a multimedia file.

Same as the STOP button on the remote control: stops playback and returns you to the previous screen.

Toggles the repetition function: Repeat 1, Repeat All, Repeat Dir and Random modes.

Sets A-B repeat to play between A and B repeatedly: press once to set point A, press again to set point B, press a third time to

cancel.

Playlist: pops up the playback list in Photo/Music mode.

Info.: Same as the INFO button on the remote control: pops up a file information window in Photo/Movie/e-Book mode.

Rotate: rotates the picture in Photo mode.

Zoom in or zoom out in Photo/MOVIE mode.

Slow: playback at 1/2, 1/4, 1/8, 1/16 speed in Movie mode.

Step: frame by frame playback in Movie mode.

Press to pop up a setup menu to adjust telecast function: this includes Repeat Mode, Background Music, Music Source, Slide Time,

Effect in Photo mode and Program, Subtitle, Audio, Repeat Mode in Movie mode.

Goto Time: enter the search date/time in Music/Movie mode.

Same as the FB/FF button on the remote control: play fast backward or forward at x2/x4/x8/x16 speed.

Same as the PREV/NEXT button on the remote control: play previous or next multimedia file directly.

Same as the BLUE button on the remote control. Used to close panel in Music mode only; it can be opened by pressing any button

on the remote control.

*Note: These functions require a USB mass storage device to be connected.

Customising TV operation

Specifications Troubleshooting Using DVB-S2 Using TV Installing Introducing Safety Warnings

Features Features LED TV LED TV

Customising TV operation

Menu Operation

All functions can be operated via the remote control or operated partially via the keyboard.

he main menu is controlled via the MENU, OK and EXIT buttons.

Use the MENU button to open the menu or go to a higher level. There are five main menu pages on the DVB-T

system: Picture, Sound, Channel, Feature, Setup.

Press the Navigation button to select a function or adjust settings, Press OK to confirm a selection, Press the

XIT button to go up a level.

Customising the Picture Settings

Picture MENU:

Allows you to make adjustments to your picture settings.

Picture Mode

Toggles between display types: Standard/Mild/User*/Dynamic.

*User: allows you to save your preferred settings.

Brightness

Controls overall brightness level of the picture: the higher the level the brighter the picture.

Contrast

Controls difference in colour and light between different parts of an image. The higher the contrast the more marked the user-

perceived difference.

Sharpness

Controls picture sharpness. Higher settings sharpen the image more.

Colour

Controls colour intensity. The higher the setting the more vivid the colour.

Tint (for NTSC system only)

Controls the difference between green and red regions of the picture.

Colour Temperature

Adjusts colour components independently to achieve a warm or cool effect: Standard/Cool/Warm

Aspect Ratio

Toggles between aspect types:

Auto/4:3/16:9/Full/Zoom1/Zoom2/Panorama etc.

NOTE: The available aspect mode may vary according to the input source signal.

*Not available in PC or USB mode.

Noise Reduction

Reduces noise and improves the appearance of the picture. Noise reduction gives good results but creates blur on pictures when

switching from Low to High. The available levels are Off/Low/Middle/High. *Not available in PC mode.

Specifications Troubleshooting Using DVB-S2 Using TV Installing Introducing Safety Warnings

Features Features LED TV LED TV

Customising TV Operation

Customising the Sound Settings

Sound MENU:

Allows you to customise the sound options and effects.

The Sound Setup menu includes the following options:

Sound Mode

Allows selection of the following sound enhancement options: *User/Standard/Movie/Music/Speech

*User: allows your preferred Bass/Treble settings to be adjusted and saved.

Bass

Controls the relative intensity of lower-pitched sound in User mode.

Treble

Controls the relative intensity of higher-pitched sound in User mode.

Balance

Adjusts relative volume between left/right soundtracks. If balance is negative, the sound on the left track is

louder. If balance is positive, the sound on the right track is louder.

Surround

Allows you to generate virtual surround sound.

AVL

Auto-adjusts sound volume.

SPDIF Mode

Allows user to modify digital sound output from the COAX port. The available options are: Off/PCM/Auto.

Specifications Troubleshooting Using DVB-S2 Using TV Installing Introducing Safety Warnings

Features Features LED TV LED TV

Page is loading ...

Teleco Televisore Led TY2/32 User manual

Brand: Teleco

Model: Televisore Led TY2/32

Category: LCD TVs

Type: User manual

Download PDF

report

Teleco Televisore Led TY2/32 User manual

Teleco Televisore Led TY2/32 User manual

Related papers

Other documents