Cisco ASA5555-CU-2AC-K9 Installation guide

Cisco Systems, Inc.

www.cisco.com

Cisco has more than 200 offices worldwide.

Addresses, phone numbers, and fax numbers

are listed on the Cisco website at

www.cisco.com/go/offices.

Cisco ASA 5500-X Series Hardware

Installation Guide

Cisco ASA 5512-X, ASA 5515-X, ASA 5525-X, ASA 5545-X, and ASA 5555-X

Released: February 28, 2012

Updated: September 18, 2014

Text Part Number: OL-32129-01

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL

STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT

WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.

THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT

SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE

OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.

The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant

to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required

to correct the interference at their own expense.

The following information is for FCC compliance of Class B devices: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If the equipment causes interference to radio or television reception, which can be

determined by turning the equipment off and on, users are encouraged to try to correct the interference by using one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Modifications to this product not authorized by Cisco could void the FCC approval and negate your authority to operate the product.

The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public

NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH

ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT

LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF

DEALING, USAGE, OR TRADE PRACTICE.

IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING,

WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO

OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this

URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership

relationship between Cisco and any other company. (1110R)

Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display

output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in

illustrative content is unintentional and coincidental.

Cisco ASA 5500-X Series Hardware Installation Guide

1

Cisco ASA 5500-X Series Hardware Installation Guide

OL-32129-01

CONTENTS

About This Guide vii

Contents vii

Document Objectives vii

Document Conventions vii

Installation Warnings viii

Where to Find Safety and Warning Information xii

Related Documentation xii

Obtaining Documentation and Submitting a Service Request xii

CHAPTER

1 Information about the ASA 5500-X 1-1

Cisco ASA 5500-X Series Chassis Overview 1-2

Internal and External USB Flash Drives 1-2

Internal USB Drive 1-2

(Optional) External USB Drives 1-2

Online Insertion and Removal Support 1-3

FAT 32 File System 1-3

Viewing Flash Memory 1-3

Solid State Drives 1-3

Management 0/0 Interface 1-4

Alarm LED 1-4

ASA 5500-X I/O Cards 1-5

SFP Modules 1-5

ASA Chassis Panels 1-6

Front Panel LEDs 1-6

Rear Panel LEDs 1-9

Rear Panel Ports 1-11

Power Supply 1-13

Hardware Specifications 1-15

Console Cable Pinouts 1-16

RJ-45 Console Cable 1-16

RJ-45 to DB-9 Console Adapter 1-18

Contents

2

Cisco ASA 5500-X Series Hardware Installation Guide

OL-32129-01

CHAPTER

2 Preparing for Installation 2-1

Installation Overview 2-1

Safety Recommendations 2-1

Maintaining Safety with Electricity 2-2

Preventing Electrostatic Discharge Damage 2-3

Working in an ESD Environment 2-3

General Site Requirements 2-3

Site Environment 2-4

Preventive Site Configuration 2-4

Power Supply Considerations 2-4

Configuring Equipment Racks 2-6

CHAPTER

3 Installing and Connecting the ASA 5500-X 3-1

Rack Mounting the Chassis 3-1

Rack Mounting Guidelines 3-1

Rack Mounting the ASA 5512-X, 5515-X, and 5525-X With Brackets 3-2

Rack Mounting the ASA 5500-X Chassis with Slide Rail Mounting System 3-4

Preparing the ASA 5512-X, ASA 5515-X, or ASA 5525-X to Use an Optional Slide Rail Rack Mount

System

3-4

Rack Mounting the Chassis with the Slide Rail Mounting System 3-5

Connecting Cables, Turning on Power, and Verifying Connectivity 3-13

CHAPTER

4 Maintenance and Upgrade Procedures for the ASA 5500-X 4-1

Removing and Replacing the Chassis Cover 4-1

Removing the Chassis Cover 4-1

Replacing the Chassis Cover 4-2

Installing an I/O Card 4-3

Installing an I/O Card in the Cisco ASA 5512-X, 5515-X, and 5525-X Chassis 4-3

Installing an I/O Card in the Cisco ASA 5545-X and 5555-X Chassis 4-7

Installing and Removing the SFP Modules 4-11

Installing the SFP Module 4-11

Removing the SFP Module 4-12

Removing and Installing the Power Supply 4-13

Removing and Installing the AC Power Supply 4-13

Installing the DC Input Power 4-15

Removing and Installing the DC Power Supply 4-19

Installing and Removing the Solid State Drive for the ASA CX SSP 4-21

Installation Scenarios 4-21

Contents

3

Cisco ASA 5500-X Series Hardware Installation Guide

OL-32129-01

Installing and Removing SSDs 4-22

Contents

4

Cisco ASA 5500-X Series Hardware Installation Guide

OL-32129-01

1

Cisco ASA 5500-X Series Hardware Installation Guide

OL-32129-01

About This Guide

Released: February 28, 2012

Updated: September 18, 2014

This guide describes how to install and maintain the Cisco ASA 5500-X series appliances. Information

in this guide applies to the following Cisco ASA 5500-X Series models: ASA 5512-X, ASA 5515-X,

ASA 5525-X, ASA 5545-X, and ASA 5555-X. References to “Cisco ASA 5500-X Series” and “ASA”

apply to all previously listed models unless specifically noted otherwise.

This preface includes the following sections:

• Document Conventions, page 1

• Installation Warnings, page 2

• Where to Find Safety and Warning Information, page 5

• Related Documentation, page 5

• Obtaining Documentation and Submitting a Service Request, page 6

Document Conventions

This document uses the following conventions:

Convention Indication

bold type Commands and keywords and user-entered text appear in bold type.

italic type Document titles, new or emphasized terms, and arguments for which you supply

values are in italic type.

[ ] Elements in square brackets are optional.

{x | y | z } Required alternative keywords are grouped in braces and separated by

vertical bars.

[ x | y | z ] Optional alternative keywords are grouped in brackets and separated by

vertical bars.

string An unquoted set of characters. Do not use quotation marks around the string, or

the string will include the quotation marks.

monospace type Terminal sessions and information the system displays appear in monospace

type.

2

Cisco ASA 5500-X Series Hardware Installation Guide

OL-32129-01

About This Guide

Document Conventions

Note Means reader take note.

Tip Means the following information will help you solve a problem.

Caution Means reader be careful. In this situation, you might perform an action that could result in equipment

damage or loss of data.

Installation Warnings

Be sure to read the Regulatory Compliance and Safety Information document

(http://www.cisco.com/c/en/us/td/docs/security/asa/hw/regulatory/compliance/asa5500x_rcsi.html)

before installing the chassis.

This section presents these important safety warnings:

• Power Supply Disconnection Warning, page 3

• More than One Power Supply Warning, page 3

• Jewelry Removal Warning, page 3

• Wrist Strap Warning, page 3

• Work During Lightning Warning, page 3

• Installation Instructions Warning, page 3

• Chassis Warning for Rack-Mounting and Servicing, page 3

• Short-Circuit Protection Warning, page 4

• SELV Circuit Warning, page 4

• Ground Conductor Warning, page 4

• Faceplates and Cover Panels Warning, page 4

• Product Disposal Warning, page 4

• Compliance with Local and National Electrical Codes Warning, page 4

• TN Power Warning, page 4

• Multiple Power Cords, page 5

monospace bold type Commands and keywords and user-entered text appear in monospace courier

type.

monospace italic

type

Arguments for which you supply values are in monospace italic type.

< > Non-printing characters such as passwords are presented in angle brackets.

[ ] Default responses to system prompts are presented in square brackets.

!, # An exclamation point (!) or a hash sign (#) at the beginning of a line of code

indicates a comment line.

3

Cisco ASA 5500-X Series Hardware Installation Guide

OL-32129-01

About This Guide

Document Conventions

• Circuit Breaker (15A) Warning, page 5

• 48 VDC Power System, page 5

• Grounded Equipment Warning, page 5

• Safety Cover Requirement, page 5

Power Supply Disconnection Warning

Warning

Before working on a chassis or working near power supplies, unplug the power cord on AC units;

disconnect the power at the circuit breaker on DC units.

Statement 12

More than One Power Supply Warning

Warning

This unit has more than one power supply connection; all connections must be removed completely

to completely remove power from the unit.

Statement 102

Jewelry Removal Warning

Warning

Before working on equipment that is connected to a power source, remove jewelry (including rings,

necklaces, and watches). Metal objects will heat when connected to power and ground, and can

cause serious burns or weld the metal object to the terminals.

Statement 43

Wrist Strap Warning

Warning

During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly

touch the backplane with your hand or any metal tool, or you could receive a shock.

Statement 94

Work During Lightning Warning

Warning

Do not work on the system, or connect or disconnect cables during periods of lightning.

Statement

1001

Installation Instructions Warning

Warning

Read all installation instructions before connecting the system to a power source.

Statement 1004

Chassis Warning for Rack-Mounting and Servicing

Warning To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to

ensure that the system remains stable. The following guidelines are provided to ensure your safety: This unit

should be mounted at the bottom of the rack if it is the only unit in the rack. When mounting this unit in a partially

4

Cisco ASA 5500-X Series Hardware Installation Guide

OL-32129-01

About This Guide

Document Conventions

filled rack, load the rack from the bottom to the top with the heaviest component at the bottom of the rack.If the

rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit in the rack.

Statement 1006

Short-Circuit Protection Warning

Warning

This product requires short-circuit (overcurrent) protection, to be provided as part of the building

installation. Install only in accordance with national and local wiring regulations.

Statement 1045

SELV Circuit Warning

Warning

To avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to telephone-network

voltage (TNV) circuits. LAN ports contain SELV circuits, and WAN ports contain TNV circuits. Some

LAN and WAN ports both use RJ-45 connectors. Use caution when connecting cables.

Statement 1021

Ground Conductor Warning

Warning

This equipment must be grounded. Never defeat the ground conductor, or operate the equipment in the

absence of a suitably installed ground conductor. Contact the appropriate electrical inspection

authority, or an electrician if you are not certain that suitable grounding is available.

Statement 1024

Faceplates and Cover Panels Warning

Warning

Blank faceplates and cover panels serve three important functions: they prevent exposure to

hazardous voltages and currents inside the chassis; they restrict electromagnetic interference

(EMI) that might disrupt other equipment; and they direct the flow of cooling air through the chassis.

Do not operate the system unless all cards, faceplates, front covers, and rear covers are in place.

Statements 1029 and 142

Product Disposal Warning

Warning

Ultimate disposal of this product should be handled according to all national laws and regulations.

Statement 1040

Compliance with Local and National Electrical Codes Warning

Warning

Installation of the equipment must comply with local and national electrical codes.

Statement 1074

TN Power Warning

Warning

The device is designed to work with TN power systems.

Statement 19

5

Cisco ASA 5500-X Series Hardware Installation Guide

OL-32129-01

About This Guide

Document Conventions

Multiple Power Cords

Warning

This unit has more than one power cord. To reduce the risk of electric shock when servicing a unit,

disconnect the power cord of the power strip into which the unit is plugged.

Statement 137

Circuit Breaker (15A) Warning

Warning

This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that

a fuse or circuit breaker no larger than 120 VAC, 15A U.S. (240 VAC, 10A international) is used on the

phase conductors (all current-carrying conductors).

Statement 13

48 VDC Power System

Warning

The customer 48-volt power system must provide reinforced insulation between the primary AC power

and the 48 VDC output.

Statement 128

Grounded Equipment Warning

Warning

This equipment is intended to be grounded. Ensure that the host is connected to earth ground during

normal use.

Statement 39

Safety Cover Requirement

Warning

The safety cover is an integral part of the product. Do not operate the unit without the safety cover

installed. Operating the unit without the cover in place will invalidate the safety approvals and pose

a risk of fire and electrical hazards.

Statement 117

Where to Find Safety and Warning Information

For safety and warning information, see the Regulatory Compliance and Safety Information document

at the following URL:

http://www.cisco.com/c/en/us/td/docs/security/asa/hw/regulatory/compliance/asa5500x_rcsi.html

This RCSI document describes the international agency compliance and safety information for the

Cisco ASA 5500-X series. It also includes translations of the safety warnings used in this guide.

Related Documentation

For a complete list of the Cisco ASA 5500-X series documentation and where to find it, see the

documentation roadmap at the following URL:

http://www.cisco.com/en/US/docs/security/asa/roadmap/asaroadmap.html

6

Cisco ASA 5500-X Series Hardware Installation Guide

OL-32129-01

About This Guide

Obtaining Documentation and Submitting a Service Request

For information on obtaining documentation, using the Cisco Bug Search Tool (BST), submitting a

service request, and gathering additional information, see What’s New in Cisco Product Documentation

at: http://www.cisco.com/c/en/us/td/docs/general/whatsnew/whatsnew.html.

Subscribe to What’s New in Cisco Product Documentation, which lists all new and revised

Cisco technical documentation, as an RSS feed and deliver content directly to your desktop using a

reader application. The RSS feeds are a free service.

CHAPTER

1-1

Cisco ASA 5500-X Series Hardware Installation Guide

OL-32129-01

1

About the ASA 5500-X

This chapter describes the Cisco ASA 5512-X, 5515-X, 5525-X, 5545-X, and 5555-X models. We

recommend that you read this entire guide before beginning any of the procedures contained herein.

Warning

Only trained and qualified personnel should install, replace, or service this equipment

.

Statement 49

Caution Read the safety warnings in the Regulatory Compliance and Safety Information document for the Cisco

ASA 5500-X (http://www.cisco.com/go/asa5500x-compliance), and follow proper safety procedures

when performing any tasks in this guide.

This chapter includes the following topics:

• Package Contents, page 1-1

• Internal and External USB Flash Drives, page 1-3

• Solid State Drives, page 1-4

• Alarm LED, page 1-4

• ASA 5500-X I/O Cards, page 1-4

• SFP Modules, page 1-5

• ASA Chassis Panels, page 1-7

• Power Supply, page 1-14

• Hardware Specifications, page 1-16

Package Contents

This section lists the package contents of each chassis. Note that contents are subject to change, and your

exact contents might contain additional or fewer items.

• ASA 5512-X, ASA 5515-X, or ASA 5525-X, page 1-2

• ASA 5545-X and ASA 5555-X, page 1-2

1-2

Cisco ASA 5500-X Series Hardware Installation Guide

OL-32129-01

Chapter 1 About the ASA 5500-X

Package Contents

ASA 5512-X, ASA 5515-X, or ASA 5525-X

ASA 5545-X and ASA 5555-X

1 ASA 5512-X, ASA 5515-X, or ASA 5525-X

Chassis

2 Blue Console Cable and Serial PC Terminal

Adapter (DB-9 to RJ-45)

3 Power Cord 4 Power Cord Retainer

5 4 10-32 Phillips Screws for rack mounting 6 4 12-24 Phillips Screws for rack mounting

7 4 M6 Phillips Screws for rack mounting

1 ASA 5545-X or ASA 5555-X Chassis

(one power supply shown)

2 Blue Console Cable and Serial PC Terminal

Adapter (DB-9 to RJ-45)

3 Power Cord 4 Power Cord Retainer

5 Rack-Mount Bracket Kit

1

3 4

2

330545

76

5

330544

1

3

2

4

5

1-3

Cisco ASA 5500-X Series Hardware Installation Guide

OL-32129-01

Chapter 1 About the ASA 5500-X

Internal and External USB Flash Drives

The Cisco ASA 5500-X has internal and (optional) external USB drives.

• Internal USB Drive, page 1-3

• External USB Drives (Optional), page 1-3

• USB Online Insertion and Removal, page 1-3

• FAT-32 File System, page 1-3

Internal USB Drive

An embedded USB (eUSB) device is used as the internal flash (disk0). See Hardware Specifications,

page 1-16 for the size shipped with each model.

External USB Drives (Optional)

The ASA 5500-X supports external USB flash drives for data storage. The ASA 5500-X uses disk1 as

the external USB flash drive identifier. When the ASA is powered on, an inserted USB flash drive is

mounted to disk1 and available for you to use. Additionally, the file system commands that are available

to disk 0 are also available to disk1, including copy, format, delete, mkdir, pwd, cd, and so on. When

you remove the USB flash drive, the system unmounts disk1, and disk1 becomes an invalid file system

label that you can no longer access.

If you insert a USB drive with more than one partition, only the first partition is mounted.

USB Online Insertion and Removal

While the ASA back panel has two USB slots, only one is supported for online insertion and removal

(OIR), with priority given to the USB drive that was inserted first. For example, based on the time

sequence, the first inserted USB flash drive is mounted to disk1, regardless of the slot in which you insert

it. When you insert a second USB device, an error message appears on the console to notify you that an

extra, unsupported USB flash drive exists. Removing either one of the USB devices does not change the

priority that you just established. To change the priority you must safely remove the USB device and

begin again to establish the desired priority.

FAT-32 File System

The ASA 5500-X supports only FAT-32-formatted file systems for the eUSB and external USB drives.

If you insert an external USB drive that is not in FAT-32 format, the system mounting process fails, and

you receive an error message. You can enter the format disk1: command to format the partition to FAT

32 and mount the partition to disk1 again; however, data might be lost.

1-4

Cisco ASA 5500-X Series Hardware Installation Guide

OL-32129-01

Chapter 1 About the ASA 5500-X

Solid State Drives

You must install a Cisco Solid State Drive (SSD) for use with the some software modules. Only Cisco

SSDs are supported. You can install one SSD in the ASA 5512-X, ASA 5515-X, and ASA 5525-X. You

can install two SSDs in a RAID 1 configuration in the ASA 5545-X and ASA 5555-X.

Note When you install an SSD for the first time, you must reload the ASA and then re-image the installed

module.

The SSD is hot-swappable. The SSD resides in a carrier, which you install into the drive bay. You can

use the SSD with an AC or DC power supply. See Install and Remove a Solid State Drive for a Services

Module, page 4-22 for more information.

Alarm LED

The ASA 5500-X performs autonomous environmental monitoring, polling all external sensors and

monitoring operating conditions. In the event of damage to certain internal components, or surpassed

temperature thresholds, the system activates an alarm LED to notify you of a critical condition. For

example, the alarm LED is activated by firmware in the event of various critical over-voltage and

over-temperature conditions, as well as when the ASA has missing or unrecognized internal chip

components. When the alarm LED lights, you can find details about the system condition from the

system message that appears on the console, or by entering the show environment or show controller

pci CLI commands.

Note If you remove one of the power-supply modules from an ASA with redundant power supplies—in other

words, one with two power supplies installed—the Alarm LED will light. To turn off the light, you must

power-cycle the chassis; that is, turn it completely off and then turn it back on. See Power Supply,

page 1-14 for more information about the redundant power-supply configuration. See Remove and

Install the Power Supply, page 4-14 for more information about removing a power supply.

ASA 5500-X I/O Cards

The ASA 5500-X six-port GigabitEthernet interface cards extend the I/O capabilities of the

ASA 5525-X, ASA 5545-X, and ASA 5555-X models by providing additional GigabitEthernet ports.

The I/O cards provide the following benefits:

• Segmentation of network traffic into separate security zones

• Fiber-optic cable connectivity for communications over long distances

• Load-sharing of traffic, and protection against link failure, using EtherChannel

• Support for Jumbo Ethernet frames of up to 9000 bytes

• Protection for Active/Active failover, and for full-mesh firewall deployments against cable failure

For information about installing an I/O card in your ASA, see Chapter 4, “Maintenance and Upgrade

Procedures for the ASA 5500-X.”

1-5

Cisco ASA 5500-X Series Hardware Installation Guide

OL-32129-01

Chapter 1 About the ASA 5500-X

SFP Modules

The ASA uses field-replaceable small form-factor pluggable (SFP) modules to establish Gigabit

Ethernet connections. Table 1-1 lists the supported SFP modules.

Use only Cisco-certified SFP modules on the ASA. Each SFP module has an internal serial EEPROM

that is encoded with security information. This encoding allows Cisco to identify and validate that the

SFP module meets the requirements for the ASA.

All SFP ports require cables with LC-type connectors. Minimum cable distance for all SFPs listed (both

SMF and MMF) is 2 m (6.5 feet); cables must not exceed specified cable lengths for reliable

communications. Table 1-2 lists the fiber-optic cable requirements.

Table 1-1 Supported SFP Modules

SFP Module Type of Connection Cisco Part Number

1000BASE-T Copper, twisted pair (RJ-45) GLC-T=

1000BASE-EX Single-mode fiber (SMF) GLC-EX-SMD=

1000BASE-ZX SMF GLC-ZX-SMD=

1000BASE-SX Multi-mode fiber (MMF) GLC-SX-MM=

1000BASE-LX/LH MMF/SMF GLC-LH-SM=

1-6

Cisco ASA 5500-X Series Hardware Installation Guide

OL-32129-01

Chapter 1 About the ASA 5500-X

SFP Modules

Table 1-2 Cabling Requirements for Fiber-optic SFP Modules

SFP Module Wavelength Fiber Type Core Size

Modal Bandwidth

(MHz-km)

1

1. Specified at transmission wavelength.

Operating

Distance

1000BASE-EX

(GLC-EX-SMD=)

1310 nm SMF —

2

2. ITU-T G.652 SMF as specified by the IEEE 802.3z standard.

— 40 km (131,234 ft)

1000BASE-ZX

(GLC-ZX-SMD=)

1550 nm SMF — — ~70 km, depending

on link loss

1000BASE-SX

(GLC-MM=)

850 nm MMF 62.5 µm 160 (FDDI grade) 220 m (722 ft)

62.5 µm 200 (OM1) 275 m (902 ft)

50 µm 400 (400/400) 500 m (1640 ft)

50 µm 500 (OM2) 550 m (1804 ft)

50 µm 2000 (OM3) 1000 m (3281 ft)

1000BASE-LX/LH

(GLC-SM=)

1310 nm MMF

3

3. An IEEE-standard, mode-conditioning patch cord is required regardless of span length. Note that the mode-conditioning

patch cord for 62.5-µm fiber has a different specification than the patch cord for 50-µm fiber.

62.5 µm 500 550 m (1804 ft)

50 µm 400 550 m (1804 ft)

50 µm 500 550 m (1804 ft)

SMF — — 10 km (32,821 ft)

1-7

Cisco ASA 5500-X Series Hardware Installation Guide

OL-32129-01

Chapter 1 About the ASA 5500-X

ASA Chassis Panels

This section describes the front and rear ASA panels, and includes the following topics:

• Front Panel LEDs, page 1-7

• Rear Panel LEDs, page 1-10

• Rear Panel Ports, page 1-12

Front Panel LEDs

Figure 1-1 shows the front panel LEDs for the ASA 5512-X, ASA 5515-X, and ASA 5525-X models.

Figure 1-1 Front Panel LEDs for the Cisco ASA 5512-X, ASA 5515-X, and ASA 5525-X

LED Description

1 Power button A soft switch that turns the system on and off. Once pressed, the

button stays in the “on” position:

• On—The power symbol on the button is lit.

• Off—The power symbol on the button is dark.

For information about the power state, see the Power Supply

Considerations, page 2-3.

2 Hard-disk release button Releases the hard disk from the device.

Cisco ASA 5515

Adapative Security Appliance

BOOT

ACTIVE

PS

ALARM

VPN

HD

282360

Cisco ASA 5515

Adapative Security Appliance

BOOT

ACTIVE

PS

ALARM

VPN

HD

1

2

5

8

7

6

3

4

1-8

Cisco ASA 5500-X Series Hardware Installation Guide

OL-32129-01

Chapter 1 About the ASA 5500-X

ASA Chassis Panels

3 Alarm System operating status:

• Off—Normal operating system function.

• Solid amber—Critical Alarm indicating one or more of

the following:

–

a major failure of a hardware or software component.

–

an over-temperature condition.

–

power voltage is outside of the tolerance range.

Note May appear red on some devices.

4 VPN VPN tunnel status:

• Solid green—VPN tunnel is established.

• Off—No VPN tunnel established.

5 HD Hard Disk Drive status:

• Flashing green—Proportioned to read/write activity.

• Solid amber—Hard-disk drive failure.

• Off—No hard-disk drive present.

6 PS Power supply status

7 Active Status of the failover pair:

• Solid green—Failover pair is operating normally.

• Off—Failover is not operational.

8 Boot Power-up diagnostics:

• Flashing green—Power-up diagnostics are running, or system

is booting.

• Solid green—System has passed power-up diagnostics.

• Off—Power-up diagnostics are not operational.

Page is loading ...

Cisco ASA5555-CU-2AC-K9 Installation guide

This manual is also suitable for

Cisco ASA5555-CU-2AC-K9 Installation guide

Related papers

Other documents