ViewSonic CDP4237-L Owner's manual

CDP4237-L

CDP4737-L

CDP5537-L

User Guide

Model No. VS14673/VS14674/VS14675

IMPORTANT: Please read this User Guide to obtain important information on installing

and using your product in a safe manner, as well as registering your product for future

service. Warranty information contained in this User Guide will describe your limited

coverage from ViewSonic Corporation, which is also found on our web site at http://

ZZZYLHZVRQLFFRPLQ(QJOLVKRULQVSHFL¿FODQJXDJHVXVLQJWKH5HJLRQDOVHOHFWLRQ

box in the upper right corner of our website. “Antes de operar su equipo lea cu

idadosamente las instrucciones en este manual”

i

Compliance Information

For U.S.A.

This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1)

this device may not cause harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there

is no guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following measures:

5HRULHQWRUUHORFDWHWKHUHFHLYLQJDQWHQQD

,QFUHDVHWKHVHSDUDWLRQEHWZHHQWKHHTXLSPHQWDQGUHFHLYHU

&RQQHFWWKHHTXLSPHQWLQWRDQRXWOHWRQDFLUFXLWGLIIHUHQWIURPWKDWWRZKLFKWKHUHFHLYHULVFRQQHFWHG

&RQVXOWWKHGHDOHURUDQH[SHULHQFHGUDGLR79WHFKQLFLDQIRUKHOS

:DUQLQJ<RXDUHFDXWLRQHGWKDWFKDQJHVRUPRGL¿FDWLRQVQRWH[SUHVVO\DSSURYHGE\WKHSDUW\UHVSRQVLEOH

for compliance could void your authority to operate the equipment.

For Canada

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

CE Conformity for European Countries

The device complies with the EMC Directive 2004/108/EC and Low Voltage Directive 2006/95/

EC.

Following information is only for EU-member states:

The mark shown to the right is in compliance with the Waste Electrical and Electronic

Equipment Directive 2002/96/EC (WEEE).

The mark indicates the requirement NOT to dispose the equipment as unsorted municipal

waste, but use the return and collection systems according to local law.

ii

Important Safety Instructions

1. Read these instructions completely before using the equipment.

2. Keep these instructions in a safe place.

3. Heed all warnings.

4. Follow all instructions.

5. 'RQRWXVHWKLVHTXLSPHQWQHDUZDWHU:DUQLQJ7RUHGXFHWKHULVNRI¿UHRUHOHFWULFVKRFNGRQRWH[SRVH

this apparatus to rain or moisture.

6. Do not block any ventilation openings. Install the equipment in accordance with the manufacturer’s

instructions.

7. Do not install near any heat sources such as radiators, heat registers, stoves, or other devices (including

DPSOL¿HUVWKDWSURGXFHKHDW

8. Do not attempt to circumvent the safety provisions of the polarized or grounding-type plug. A polarized

plug has two blades with one wider than the other. A grounding type plug has two blades and a third

JURXQGLQJSURQJ7KHZLGHEODGHDQGWKHWKLUGSURQJDUHSURYLGHGIRU\RXUVDIHW\,IWKHSOXJGRHVQRW¿W

into your outlet, consult an electrician for replacement of the outlet.

9. Protect the power cord from being tread upon or pinched, particularly at the plug, and the point where

if emerges from the equipment. Be sure that the power outlet is located near the equipment so that it is

easily accessible.

10. 2QO\XVHDWWDFKPHQWVDFFHVVRULHVVSHFL¿HGE\WKHPDQXIDFWXUHU

11. 8VHRQO\ZLWKWKHFDUWVWDQGWULSRGEUDFNHWRUWDEOHVSHFL¿HGE\WKHPDQXIDFWXUHURUVROG

with the equipment. When a cart is used, use caution when moving the cart/equipment

combination to avoid injury from tipping over.

12. Unplug this equipment when it will be unused for long periods of time.

13. 5HIHUDOOVHUYLFLQJWRTXDOL¿HGVHUYLFHSHUVRQQHO6HUYLFHLVUHTXLUHGZKHQWKHXQLWKDVEHHQGDPDJHG

in any way, such as: if the power-supply cord or plug is damaged, if liquid is spilled onto or objects fall

into the unit, if the unit is exposed to rain or moisture, or if the unit does not operate normally or has

been dropped.

iii

Declaration of RoHS Compliance

This product has been designed and manufactured in compliance with Directive 2002/95/EC of the European

Parliament and the Council on restriction of the use of certain hazardous substances in electrical and

electronic equipment (RoHS Directive) and is deemed to comply with the maximum concentration values

issued by the European Technical Adaptation Committee (TAC) as shown below:

Substance

Proposed Maximum Concentration

Actual Concentration

Lead (Pb) 0,1% < 0,1%

Mercury (Hg) 0,1% < 0,1%

Cadmium (Cd) 0,01% < 0,01%

Hexavalent Chromium (Cr6+) 0,1% < 0,1%

Polybrominated biphenyls (PBB) 0,1% < 0,1%

Polybrominated diphenyl ethers (PBDE) 0,1% < 0,1%

Certain components of products as stated above are exempted under the Annex of the RoHS Directives as

noted below:

Examples of exempted components are:

 0HUFXU\LQFRPSDFWÀXRUHVFHQWODPSVQRWH[FHHGLQJPJSHUODPSDQGLQRWKHUODPSVQRWVSHFL¿FDOO\

mentioned in the Annex of RoHS Directive.

 /HDGLQJODVVRIFDWKRGHUD\WXEHVHOHFWURQLFFRPSRQHQWVÀXRUHVFHQWWXEHVDQGHOHFWURQLFFHUDPLF

parts (e.g. piezoelectronic devices).

3. Lead in high temperature type solders (i.e. lead-based alloys containing 85% by weight or more lead).

4. Lead as an allotting element in steel containing up to 0.35% lead by weight, aluminium containing up

to 0.4% lead by weight and as a cooper alloy containing up to 4% lead by weight.

1

Copyright Information

®

ViewSonic

®

, the three birds logo, OnView

®

, ViewMatch

™

, and ViewMeter

®

are registered trademarks of

ViewSonic

®

Corporation.

ENERGY STAR

®

is a registered trademark of the U.S. Environmental Protection Agency (EPA).

As an ENERGY STAR

®

partner, ViewSonic Corporation has determined that this product meetsthe ENERGY

STAR

®

JXLGHOLQHVIRUHQHUJ\HI¿FLHQF\

Disclaimer: ViewSonic

®

Corporation shall not be liable for technical or editorial errors or omissions contained

herein; nor for incidental or consequential damages resulting from furnishing this material, or the performance

or use of this product.

In the interest of continuing product improvement, ViewSonic

®

Corporation reserves the right to change

SURGXFWVSHFL¿FDWLRQVZLWKRXWQRWLFH,QIRUPDWLRQLQWKLVGRFXPHQWPD\FKDQJHZLWKRXWQRWLFH

No part of this document may be copied, reproduced, or transmitted by any means, for any purpose without

prior written permission from ViewSonic

®

Corporation.

Product Registration

To meet your future needs, and to receive any additional product information as it becomes available, please

register your product on the Internet at: www.viewsonic.com.

For Your Records

Product Name:

Model Number:

Document Number:

Serial Number:

Purchase Date:

CDP4237-L/CDP4737-L/CDP5537-L

ViewSonic LCD Commercial Display

VS14673/VS14674/VS14675

CDP4237-L_4737-L_5537-L_UG_ENG Rev. 1A 02-03-12

Product disposal at end of product life

ViewSonic respects the environment and is committed to working and living green. Thank you for being part

of Smarter, Greener Computing. Please visit ViewSonic website to learn more.

USA & Canada: http://www.viewsonic.com/company/green/recycle-program/

Europe: http://www.viewsoniceurope.com/uk/kbase/article.php?id=639

Taiwan: http://recycle.epa.gov.tw/recycle/index2.aspx

2

CONTENTS

4 LICENSES

5 ASSEMBLING AND

PREPARING

5 Accessories

6 Optional Accessories

7 Parts and buttons

8 Using the Mounting Cable Tie

8 Connecting the Speakers

9 Connecting the stand

9 Using the Kensington security system

10 Portrait Layout

11 Mounting on a wall

12 REMOTE CONTROL

14 USING THE MONITOR

14 Connecting to a PC

15 - RGB connection

15 - DVI-D connection

16 - HDMI connection

16 - Display Port connection

17 Adjusting the screen

17 - Selecting an image mode

17 - Customizing image options

18 - Customizing PC display options

18 Adjusting the sound

18 - Selecting an sound mode

19 - Customizing sound options

19 Using additional options

19 - Adjusting aspect ratio

21 - Using the input list

22 ENTERTAINMENT

22 - Connecting to a wired network

23 - Network Status

24 - Connecting USB storage devices

25 - Browsing files

26 - Viewing movies

30 - Viewing photos

33 - Listening to music

36 - DivX® VOD Guide

37 - Using PIP/PBP

39 CUSTOMIZING SETTINGS

39 Accessing main menus

40 - PICTURE settings

43 - AUDIO settings

44 - TIME settings

45 - OPTION settings

50 - NETWORK settings

51 MAKING CONNECTIONS

52 Connecting to a HD receiver, DVD,

Camcorder, Camera, Gaming Device or

VCR player

52 - HDMI connection

52 - Component connection

53 - AV(CVBS) connection

53 Connecting to a USB

54 Connecting to the LAN

54 - LAN connection

55 Daisy Chain Monitors

3

56 TROUBLESHOOTING

59 SPECIFICATIONS

67 IR CODES

68 CONTROLLING THE MULTIPLE

PRODUCT

68 Connecting the cable

68 RS-232C Configurations

68 Communication Parameter

4

LICENSES

Supported licenses may differ by model. For more information of the licenses, visit www.ViewSonic.com.

HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks

or registered trademarks of HDMI Licensing LLC.

ABOUT DIVX VIDEO: DivX is a digital video format created by DivX, LLC, a

subsidiary of Rovi Corporation. This is an official DivX Certified

device that

plays DivX video. Visit divx.com for more information and software tools to

convert your files into DivX videos.

ABOUT DIVX VIDEO-ON-DEMAND: This DivX

Certified

device must be registered in order to play purchased DivX Video-

on-Demand (VOD) movies. To obtain your registration code, locate the

DivX VOD section in your device setup menu. Go to vod.divx.com for more

information on how to complete your registration.

DivX Certified

to play DivX video up to HD 1080p, including premium

content.

DivX

, DivX Certified and associated logos are trademarks of Rovi

Corporation or its subsidiaries and are used under license.

Covered by one or more of the following U.S. patents: 7,295,673; 7,460,668;

7,515,710; 7,519,274

Manufactured under license from Dolby Laboratories. “Dolby” and the

double-D symbol are trademarks of Dolby Laboratories.

5

ASSEMBLING AND PREPARING

Accessories

Check your product box for the following items. If there are any missing accessories, contact the local

dealer where you purchased your product. The illustrations in this manual may differ from the actual product

and accessories.

y

Do not use any pirated items to ensure the safety and product life span.

y

Any damages or injuries by using pirated items are not covered by the warranty.

y

The accessories supplied with your product may vary depending on the model.

y

Product specifications or contents in this manual may be changed without prior notice due to upgrade

of product functions.

Remote control and Batteries Power Cord

CD (Owner's Manual)

/ Card

D-sub 15 pin signal cable Mounting Cable Tie

(Provided for CDP4237-L and

CDP4737-L models only)

CAUTION

NOTE

P

A

G

E

INPUT

ENERGY

SAVING

MARK

ARC

ON

OFF

X

. , !

Y

ABC

Z

DEF

[

GHI

\

JKL

]

MNO

^

PQRS

_

TUV

`

1/a/A

W

- * #

WXYZ

CLEAR

MONITOR

PSM

AUTO

MUTE

BRIGHT

NESS

MENU

POWER

OK

ID

BACK

TILE

ON

OFF

EXIT

6

Optional Accessories

Without prior notice, optional accessories are subject to change to improve the performance of the product,

and new accessories may be added. The illustrations in this manual may differ from the actual product and

accessories.

y

Cable holder/Cable tie may not be available in some areas or for some models.

y

Optional accessories are not included for all models.

Stand

Screws

: Diameter 4.0 mm x Pitch 0.7 mm x

Length 10mm(Included Spring Washer)

Cable holder

/Cable Tie

Screws

Diameter 4.0 mm x Pitch 0.7 mm x

Length 8 mm(Included Spring Washer)

Speaker

NOTE

Stand kit (STND-019)

Speaker kit (SPK-012)

7

y

You can set the Power indicator to on or off by selecting OPTION in the main menu.

Parts and buttons

Screen Marks Description

INPUT Changes the input source.

MENU Accesses the main menus, or saves your input and exits the menus.

Adjust the up and down.

Adjusts the volume level.

AUTO/SET Displays the current signal and mode.

Press this button to adjust the screen automatically (available only in RGB mode)

/I

Turns the power on or off.

IR Receiver This is where the unit receives signals from the remote control.

Power Indicator This Indicator lights up blue when the display operates normally(on mode). If the display

In sleep mode (In Power Saving mode), this indicator color changes to amber.

Connection panel

Screen Buttons

Screen Marks

IR Receiver /

Power Indicator

y

Lighting On: Turned on

y

Lighting Off: Turned off

NOTE

MEZ63829306(REV00)

8

Connecting the Speakers

- Only on some models.

1

Connect an input signal cable to use before

installing the speakers.

3

After installing your speakers, use holders and

cable ties to organize the speaker cables.

2

Mount the speaker by using a screw as shown

in the following. Then connect the speaker

cable.

Using the Mounting Cable

Tie

- Applicable only to CDP4237-L and CDP4737-L

models.

First, connect the input signal cable to be used.

Insert the cable tie into the bottom hole on the

back as shown in the figure to organize cables.

y

The Mounting cable tie is provided for

CDP4237-L and CDP4737-L models only.

NOTE

9

2

Use the screws to secure the stand on the rear

side of the product as shown in the diagram.

Connecting the stand

- Only on some models.

1

Place a soft cloth on the table and put the

product with the screen facing downward.

Connect the stand as shown in the following

picture.

Using the Kensington

security system

The Kensington security system connector is

located at the back of the Monitor. For more

information of installation and using, refer to the

manual supplied with the Kensington security

system or visit

http://www.kensington.com

.

Connect the Kensington security system cable

between the Monitor and a table.

y

The Kensington security system is optional.

You can obtain additional accessories from

most electronics stores.

NOTE

10

Portrait Layout

- Only on some models.

When installing in a Portrait Layout, rotate the

monitor clockwise 90 degrees (when facing the

screen).

11

Mounting on a wall

For proper ventilation, allow a clearance of 10

cm on each side and from the wall. Detailed

installation instructions are available from your

dealer, see the optional Tilt Wall Mounting Bracket

Installation and Setup Guide.

10 cm

If you intend to mount the Monitor to a wall, attach

Wall mounting interface (optional parts) to the back

of the set.

When you install the Monitor using the wall

mounting interface (optional parts), attach it

carefully so it will not fall.

1

Please, Use the screw and wall mount interface

in accordance with VESA Standards.

2

If you use screw longer than standard, the

monitor might be damaged internally.

3

If you use improper screw, the product might

be damaged and drop from mounted position.

In this case, ViewSonic Electronics is not

responsible for it.

4

VESA compatible.

5

Please use VESA standard as below.

y

785mm(31 inch) or greater

* Fastening screw: Diameter 6.0 mm x Pitch 1.0

mm x Length 10 mm

y

Disconnect the power before installing or

moving the monitor. Otherwise electric shock

may occur.

y

If you install the Monitor on a ceiling or

slanted wall, it may fall and result in severe

injury. Use an authorized ViewSonic wall

mount and contact the local dealer or

qualified personnel.

y

Do not over tighten the screws as this may

cause damage to the Monitor and void your

warranty.

y

Use screws and wall mounts that meet the

VESA standard. Any damages or injuries by

misuse or using an improper accessory are

not covered by the warranty.

y

Use screws that are listed on the VESA

standard screw specifications.

y

The wall mount kit includes an installation

manual and necessary parts.

y

The wall mount bracket is optional. You can

obtain additional accessories from your local

dealer.

y

The length of screws may differ depending

on the wall mount. Be sure to use the proper

length.

y

For more information, refer to the instructions

supplied with the wall mount.

CAUTION

NOTE

12

REMOTE CONTROL

P

A

G

E

INPUT

ENERGY

SAVING

MARK

ARC

ON

OFF

X

. , !

Y

ABC

Z

DEF

[

GHI

\

JKL

]

MNO

^

PQRS

_

TUV

`

1/a/A

W

- * #

WXYZ

CLEAR

S.MENU

MONITOR

PSM

AUTO

MUTE

BRIGHT

NESS

MENU

POWER

/ I (POWER)

Turns the Monitor on or off.

MONITOR ON / OFF

Turn off the monitor and then

turn it back on.

1/a/A Button

This button selection is not

applicable.

ENERGY SAVING

Adjusts the brightness of

the screen to reduce energy

consumption.

INPUT

Selects the input mode.

Number and Alphabet buttons

Enters numbers.

The alphabet selection is not

applicable.

CLEAR

This button selection is not

applicable.

PSM

Selects the Picture Status

Mode.

MUTE

Mutes all sounds.

ARC

Selects the Aspect Ratio

Mode.

Volume Up / Down

Adjusts the volume level.

BRIGHTNESS Key

Adjust the brightness by

pressing the Up and Down

buttons on the remote control.

In USB mode, the OSD menu

has the Page function to move

to the next file list.

The descriptions in this manual are based on the buttons of the remote control. Please read this manual

carefully and use the Monitor correctly.

To replace batteries, open the battery cover, replace batteries (1.5 V AAA) matching

and ends to the

label inside the compartment, and close the battery cover.

To remove the batteries, perform the installation actions in reverse.

y

Do not mix old and new batteries, as this

may damage the remote control.

y

Make sure to point the remote control at the

remote control sensor on the Monitor.

CAUTION

13

E

OK

AUTO

MUTE

NESS

MENU

ID

BACK

TILE

ON

OFF

EXIT

Clears all on-screen displays

and returns to Monitor

viewing from any menu.

TILE

Selects the TILE Mode.

MENU (See p.39)

Accesses the main menus

or saves your input and exit

menus.

Navigation buttons

Scrolls through menus or

options.

OK

Selects menus or options and

confirms your input.

BACK

Allows the user to move back

one step.

USB Menu control buttons

Controls media playback.

ID ON/OFF

When more than one monitor

is present in the same room,

this allows you to control them

individually.

AUTO

Automatically adjusts picture

position and minimizes image

instability.(RGB input only)

14

USING THE MONITOR

Connecting to a PC

Your Monitor supports the Plug & Play* feature.

* Plug & Play: This is the function that allows a PC

to use the monitor without installing a driver.

NOTE

y

Connect the signal

input cable and tighten

it by turning the screws

clockwise.

y

Do not press the

screen with your finger for a long time as

this may result in temporary distortion on the

screen.

y

Avoid displaying a fixed image on the screen

for a long period of time to prevent image

burn. Use a screensaver if possible.

y

It is recommended to use the Monitor with

the HDMI connection for the best image

quality.

y

Use a shielded signal interface cable, such

as D-sub 15 pin signal cable and DVI cable,

with a ferrite core to maintain standard

compliance for the product.

y

If you turn the Monitor on when the set

becomes cold, the screen may flicker. This

is normal.

y

Some red, green, or blue spots may appear

on the screen. This is normal.

CAUTION

15

DVI-D connection

Transmits the digital video signal from your PC to

the Monitor. Connect the PC and the Monitor

set with the DVI cable as shown the following

illustrations.

Select DVI-D input source on the monitor.

RGB OUT (PC)

AUDIO OUT

RGB connection

Transmits the analog video signal from your PC to

the Monitor. Connect the PC and the Monitor

set with the 15 pin signal cable as shown the

following illustrations.

Select RGB input source on the monitor.

y

Use the standard Macintosh

adapter since an incompatible

adapter is available in the

market. (Different signaling

system)

y

Apple computers may require an adapter to

connect to this monitor. Call or visit their web

site for more information.

NOTE

AUDIO OUT

DVI OUT

Macintosh Adapter

(not included)

16

HDMI connection

Transmits the digital video and audio signals from

your PC to the Monitor. Connect the PC and the

Monitor with the HDMI cable as shown in the

following illustrations.

Select HDMI input source.

Display Port connection

Transmits the digital video and audio signals from

your PC to the Monitor. Connect the PC and the

Monitor with the Display Port cable as shown in

the following illustrations.

Select Display Port input source.

y

Use a High Speed HDMI™ Cable.

y

Please check the PC environment if you

cannot hear the sound in HDMI mode. Some

PCs require you to manually change the

default audio output to HDMI.

y

If you want to use HDMI PC mode, you must

set PC/DTV to PC mode.

y

When HDMI PC is used, a compatiblity

problem might occur.

NOTE

HDMI

DP OUT

(not included)

Page is loading ...

ViewSonic CDP4237-L Owner's manual

This manual is also suitable for

ViewSonic CDP4237-L Owner's manual

Related papers

Other documents