FormNo.3363-429RevA
Snowthrower
forCompactUtilityLoaders
ModelNo.22456—SerialNo.310000001andUp
ToregisteryourproductordownloadanOperator'sManualorPartsCatalogatnocharge,gotowww.Toro.com.OriginalInstructions(EN)
ThisproductcomplieswithallrelevantEuropean
directives,fordetailspleaseseetheseparateproduct
specicDeclarationofConformity(DOC)sheet.
Introduction
ThissnowthrowerisintendedtobeusedonaToro
compactutilityloader.Itisdesignedprimarilyfor
removingsnowfrompavedsurfaces,suchasdriveways
andsidewalks,andothersurfacesfortrafcon
residentialorcommercialproperties.Itisnotdesigned
forremovingmaterialsotherthansnow,norisitamodel
withapivotingscraperdesignedforclearingoffgravel
surfaces.Itisnotdesignedforuseonnon-Torotraction
units.
Readthisinformationcarefullytolearnhowtooperate
andmaintainyourproductproperlyandtoavoidinjury
andproductdamage.Youareresponsibleforoperating
theproductproperlyandsafely.
YoumaycontactTorodirectlyatwww.Toro.comfor
productandaccessoryinformation,helpndinga
dealer,ortoregisteryourproduct.
Wheneveryouneedservice,genuineToroparts,or
additionalinformation,contactanAuthorizedService
DealerorToroCustomerServiceandhavethemodel
andserialnumbersofyourproductready.Themodel
andserialnumbersareprintedonaplatelocatedonthe
rightsideofthedrivehead.Writethenumbersinthe
spaceprovided.
ModelNo.
SerialNo.
Thismanualidentiespotentialhazardsandhas
safetymessagesidentiedbythesafetyalertsymbol
(
Figure1),whichsignalsahazardthatmaycauseserious
injuryordeathifyoudonotfollowtherecommended
precautions.
Figure1
1.Safetyalertsymbol
Thismanualalsouses2wordstohighlightinformation.
Importantcallsattentiontospecialmechanical
informationandNoteemphasizesgeneralinformation
worthyofspecialattention.
Contents
Introduction.................................................................2
Safety...........................................................................3
GeneralSnowthrowerSafety.................................3
ToroSnowthrowerSafety.....................................4
StabilityRatings....................................................5
SafetyandInstructionalDecals.............................5
Setup............................................................................7
1InstallingtheDischargeChute............................7
2InstallingtheCableGuide(200/300Series
TractionUnitsOnly).........................................7
3InstallingtheSnowthrower................................8
ProductOverview......................................................10
Specications.....................................................10
Attachments/Accessories...................................10
Operation...................................................................10
RemovingtheSnowthrower................................10
OperatingTips...................................................10
Maintenance...............................................................12
RecommendedMaintenanceSchedule(s)................12
Checking/AdjustingtheDischarge
Chute.............................................................12
CheckingtheAugerGearBoxOil.......................12
ReplacingtheScraperBlade................................13
AdjustingtheSkids.............................................13
Storage.......................................................................14
Troubleshooting.........................................................15
©2009—TheToro®Company
8111LyndaleAvenueSouth
Bloomington,MN55420
2
Contactusatwww.Toro.com.
PrintedintheUSA.
AllRightsReserved
Safety
Improperuseormaintenancebytheoperatoror
ownercanresultininjury.Toreducethepotential
forinjury,complywiththesesafetyinstructionsand
thoseinthetractionunit
Operator’ s Man ual
.Always
payattentiontothesafetyalertsymbol,which
means
Caution
,
W ar ning
,or
Danger
—personal
safetyinstruction.Failuretocomplywiththe
instructionmayresultinpersonalinjuryordeath.
DANGER
Whenthesnowthrowerisinoperation,theimpeller
andaugercanberotatingandcutofforinjure
handsandfeet.
•Beforeadjusting,cleaning,repairingand
inspectingthesnowthrower,andbefore
uncloggingthedischargechute,
mo v e the
auxiliar y h y draulics lev er to the of f position,
stop the engine, and w ait f or all mo ving par ts to
stop .
Removethekey.
•Useastick,
not y our hands
,toremovean
obstructionfromthedischargechute.
•Staybehindthehandlesandawayfrom
thedischargeopeningwhileoperatingthe
snowthrower.
•Keepface,hands,feet,andanyotherpartof
yourbodyorclothingawayfromconcealed,
moving,orrotatingparts.
WARNING
Theauger/impellermaypickupandthrowstones,
toys,andotherforeignobjects,causingserious
personalinjurytotheoperatorortobystanders.
•Keeptheareatobeclearedfreeofallobjects
thatcouldbepickedupandthrownbythe
auger/impeller.
•Keepallchildrenandpetsawayfromareaof
operation.
WARNING
Whentheengineisoff,attachmentsintheraised
positioncangraduallylower.Someonenearbymay
bepinnedorinjuredbytheattachmentasitlowers.
Alwayslowertheattachmentlifteachtimeyoushut
offthetractionunit.
WARNING
Ifyoudonotfullyseattheattachmentlocking
pinsintheattachmentmountplateholes,the
attachmentcouldfalloffofthetractionunitseverely
injuringtheoperatororbystanders.
•Ensurethatyoufullyseattheattachment
lockingpinsthroughtheholesintheattachment
mountplatebeforeliftingtheattachment.
•Ensurethattheattachmentmountplateisfreeof
anydirtordebristhatmayhindertheconnection
ofthetractionunittotheattachment.
•Refertoyourtractionunit
Operator’ s Man ual
fordetailedinformationonsafelyconnectingan
attachmenttoyourtractionunit.
CAUTION
Hydrauliccouplers,hydrauliclines/valves,and
hydraulicuidmaybehotandcanburnyouifyou
touchthem.
•Weargloveswhenoperatingthehydraulic
couplers.
•Allowthetractionunittocoolbeforetouching
hydrauliccomponents.
•Donottouchhydraulicuidspills.
GeneralSnowthrowerSafety
Thefollowinginstructionshavebeenadaptedfromthe
ANSI/OPEIandISOstandards.
Preparation
•Thoroughlyinspecttheareawheretheequipmentis
tobeusedandremovealldoormats,sleds,boards,
wires,andotherforeignobjects.
•Donotoperatetheequipmentwithoutwearing
adequatewinteroutergarments.Wearfootwearthat
willimprovefootingonslipperysurfaces.
•Adjusttheaugerhousingheighttocleargravelor
crushedrocksurface.
•Neverattempttomakeanyadjustmentswhile
theengineisrunning,exceptwhenspecically
recommendedbyToro.
•Letengineandmachineadjusttooutdoor
temperaturesbeforestartingtoclearsnow .
•Theoperationofanypoweredmachinecanresultin
foreignobjectsbeingthrownintotheeyes.Always
wearsafetyglassesoreyeshieldsduringoperationor
whileperforminganadjustmentorrepair.
3
Operation
•Donotputhandsorfeetnearorunderrotatingparts.
Keepclearofthedischargeopeningatalltimes.
•Exerciseextremecautionwhenoperatingonor
crossinggraveldrives,walks,orroads.Stayalertfor
hiddenhazardsortrafc.Donotcarrypassengers.
•Afterstrikingaforeignobject,stoptheengine,
cycletheauxiliaryhydraulicslever,disconnectthe
hydrauliclines,thoroughlyinspectthesnowthrower
foranydamage,andrepairthedamagebefore
restartingandoperatingthesnowthrower.
•Iftheunitshouldstarttovibrateabnormally,stop
theengineandcheckimmediatelyforthecause.
Vibrationisgenerallyawarningoftrouble.
•Stoptheenginewheneveryouleavetheoperating
position,beforeuncloggingtheauger/impeller
housingordischargechute,andwhenmakingany
repairs,adjustments,orinspections.
•Whencleaning,repairing,orinspecting,stopthe
engine,makecertaintheauger/impellerandall
movingpartshavestopped,cycletheauxiliary
hydraulicslever,anddisconnectthehydrauliclines.
•Donotclearsnowacrossthefaceofslopes.Exercise
extremecautionwhenchangingdirectiononslopes.
Donotattempttoclearsteepslopes.
•Neveroperatethesnowthrowerwithoutproper
guards,plates,orothersafetyprotectivedevicesin
place.
•Neveroperatethesnowthrowernearglass
enclosures,automobiles,windowwells,drop-offs,
andthelikewithoutproperadjustmentofthesnow
dischargeangle.Keepchildrenandpetsaway.
•Donotoverloadthemachinecapacitybyattempting
toclearsnowattoofastarate.
•Neveroperatethemachineathightransportspeeds
onslipperysurfaces.Lookbehindandusecarewhen
movinginreverse.
•Neverdirectdischargeatbystandersorallowanyone
infrontoftheunit.
•Disengagepowertotheauger/impellerwhenthe
snowthroweristransportedornotinuse.
•Neveroperatethesnowthrowerwithoutgood
visibilityorlight.
MaintenanceandStorage
•Checkfastenersatfrequentintervalsforproper
tightnesstobesuretheequipmentisinsafeworking
condition.
•AlwaysrefertotheOperator’sManualforimportant
detailsifthesnowthroweristobestoredforan
extendedperiod.
•Maintainorreplacesafetyandinstructionlabels,as
necessary.
•Runthemachineafewminutesafterthrowingsnow
topreventfreeze-upoftheauger/impeller.
ToroSnowthrowerSafety
Thefollowinglistcontainssafetyinformationspecicto
Toroproductsorothersafetyinformationthatyoumust
knowthatisnotincludedintheANSIorISOstandards.
•Therotatingauger/impellerorrotorbladescancut
offorinjurengersorhands.Stayintheoperator’s
positionandawayfromthedischargeopeningwhile
operatingthesnowthrower.Keepyourfacehands,
feet,andanyotherpartofyourbodyorclothing
awayfromconcealed,moving,orrotatingparts.
•Beforeadjusting,cleaning,repairing,andinspecting
thesnowthrower,andbeforeuncloggingthe
dischargechute,stoptheengine,removethekey,
andwaitforallmovingpartstostop.Also,cycle
theauxiliaryhydraulicsleveranddisconnectthe
hydrauliclines.
•Useastick,notyourhandstoremoveobstructions
fromthedischargechute.
•Beforeleavingtheoperator’sposition,stopthe
engine,removethekey,andwaitforallmovingparts
tostop.
•Donotwearloosettingclothingthatcouldpossibly
getcaughtinmovingparts.
•Ifashield,safelydevice,ordecalisdamaged,
illegible,orlost,repairorreplaceitbeforebeginning
operation.Also,tightenanyloosefasteners.
•Donotusethesnowthroweronaroof.
•Performonlythosemaintenanceinstructions
describedinthismanual.Beforeperformingany
maintenance,service,oradjustment,stoptheengine,
removethekey,cycletheauxiliaryhydraulicslever,
anddisconnectthehydrauliclines.Ifmajorrepairs
areeverneeded,contactyourAuthorizedToro
ServiceDealer.
•Toensurethebestperformanceandsafety,purchase
onlygenuineTororeplacementpartsandaccessories
tokeeptheToroallToro.Donotuse“WillFit”
replacementpartsandaccessoriesastheycould
causeasafetyhazard.
•Whenusingthesnowthrowerinaraisedposition,
stayawayfromoverheadpowerlinesanddrivethe
tractionunitonlyonlevelsurfaces.
4
•Alwaystransportthesnowthrowerinalowered
position.
•Usethesnowthroweronlytoremovesnow .Other
materialsmaydamagethesnowthrowerandcause
ahazard.
•Donottiltthesnowthrowersothatitdischarges
towardstheoperatororbystanders.
StabilityRatings
Todeterminethedegreeofslopeyoucantraversewith
theattachmentinstalledonatractionunit,ndthe
stabilityratingforthehillpositionyouwanttotravel
intheappropriatetablebelow,thenndthedegreeof
slopeforthesameratingandhillpositionintheStability
DatasectionofthetractionunitOperator’sManual.
WARNING
Exceedingthemaximumrecommendedslope
cancausethetractionunittotip,crushingyouor
bystanders.
Donotdrivethetractionunitonaslopesteeper
thanthemaximumrecommendedslope,as
determinedinthefollowingtablesandthetraction
unit
Operator’ s Man ual
.
Important:Ifyouhaveatractionunitotherthan
theTX,thesnowthrowerisratedforusewithout
thecounterweight.Ifyouusethecounterweight
withthesnowthrower,thetractionunitwillbeless
stableinthefrontandsideuphillpositions.
OrientationStabilityRating
FrontUphill
C
RearUphill
C
SideUphill
B
SafetyandInstructionalDecals
Safetydecalsandinstructionsareeasilyvisibletotheoperatorandarelocatednearanyareaof
potentialdanger.Replaceanydecalthatisdamagedorlost.
63–3510
1.Dischargechuterotation
5
93-7133
1.Cutting/dismembermenthazard,auger/impeller—stayaway
frommovingparts.
2.Warning—removetheignitionkeyandreadtheinstructions
beforeservicingorperformingmaintenance.
3.Thrownobjecthazard—keepbystandersawayfromthe
machine.
4.Warning—readtheOperator’sManual.
93-7309
1.Cutting/dismembermenthazard,impeller—removethe
ignitionkeyandreadtheinstructionsbeforeservicingor
performingmaintenance.
93-7310
1.Cutting/dismembermenthazard,auger—keepbystanders
awayfromthemachine.
6
Setup
LooseParts
Usethechartbelowtoverifythatallpartshavebeenshipped.
ProcedureDescription
Qty.
Use
Snowthrowerhousing
1
Dischargechuteassembly1
Deectorshield
1
Carriagebolt
3
Washer3
1
Locknut3
Installthedischargechute.
2
Cableguide
1
Installthecableguide(200/300series
tractionunitsonly).
Chutecontrolbracket
1
Knob2
Handleclamp(200/300seriesonly)
1
Washer,large(200/300seriesonly)
1
Washer,small(200/300seriesonly)
1
Mountingbracket(TXseriesonly)
1
Self-tappingscrews(5/16x3/4inch)
(TXseriesonly)
2
3
Retainingplate(TXseriesonly)
1
Instalthesnowthrower.
1
InstallingtheDischargeChute
Partsneededforthisprocedure:
1
Snowthrowerhousing
1Dischargechuteassembly
1
Deectorshield
3
Carriagebolt
3Washer
3Locknut
Procedure
Installthedeectorshieldandthedischargechute
assemblyontothesnowthrowerhousingwiththree
carriagebolts(headstoinside),washers,andlocknuts
(
Figure2).
G01 1829
1
2
3
4
5
Figure2
1.Dischargechute4.Locknut
2.Carriagebolt5.Deectorshield
3.Washer
7
2
InstallingtheCableGuide
(200/300SeriesTractionUnits
Only)
Partsneededforthisprocedure:
1
Cableguide
Procedure
1.Ifyourtractionunithasaboltinstalledinthe
undersideoftheloaderarmcrossbar,betweenthe
rightloaderarmandthehydraulichoses,remove
thebolt.
2.Placethecableguideovertheloaderarmcrossbar
onthefarrightside(
Figure3).
G01 1830
1
2
3
4
5
Figure3
1.Cableguide4.Slot
2.Loaderarmcrossbar5.Knob
3.Clamp
3.Inserttheclampintotheslotinthecableguide,then
secureitwithaknob(
Figure3).
3
InstallingtheSnowthrower
Partsneededforthisprocedure:
1
Chutecontrolbracket
2Knob
1
Handleclamp(200/300seriesonly)
1
Washer,large(200/300seriesonly)
1
Washer,small(200/300seriesonly)
1
Mountingbracket(TXseriesonly)
2
Self-tappingscrews(5/16x3/4inch)(TXseriesonly)
1
Retainingplate(TXseriesonly)
InstallingtheSnowthrowerona200/300
SeriesTractionUnit
1.Connectthesnowthrowertothetractionunitmount
plateandconnectthehydrauliclines.Refertoyour
tractionunitOperator’sManualforinstructions.
2.Locatetheholeinthesideplateoftheframe
(
Figure4)thatislocatedjustbehindandtotheleft
ofthelefthandle.
G01 1831
1
2
3
4
5
6
3
Figure4
1.Chutecontrolbracket4.Lefthandle
2.Upperleftsideplate
5.Largewasher
3.Knob6.Handleclamp
Ifthereisnohole,completethefollowing:
A.Copythetemplateatthebackofthebook,cut
outthetemplate,andalignitwiththeupperleft
sideplateofthetractionunit(thearrowonthe
templateshouldpointup).
Note:Thetemplateisdesignedtotonthe
outsideofthesideplate.
B.Marktheholelocationonthesideplateatthe
centerofthecrosshairsonthetemplate.
8
C.Drilla3/8to1/2inch(1to1.25cm)hole
throughtheframeatthemarkedlocation.
3.Placethechutecontrolbracketbetweentheleft
handleandthesideplate(
Figure4).
4.Securethebrackettotheframewithaknobandthe
largewasher(Figure4).
5.Insertthehandleclampintotheslotinthechute
controlbracket,wrappingitaroundthehandle,then
secureitwithaknob(
Figure4).
6.Routethechutecontrolcablethroughthecable
guide.
InstallingtheSnowthroweronaTX
SeriesTractionUnit
1.Connectthesnowthrowertothetractionunitmount
plateandconnectthehydrauliclines.Refertoyour
tractionunitOperator’sManualforinstructions.
2.Alignthebracketassemblyontheleftsideofthe
tractionunitasillustratedin
Figure5.
G01 1832
1
2
3
4
5
Figure5
1.Chutecontrolbracket4.Locationfor3/8in.hole
throughthecontrolpanel.
2.Mountingbracket
5.Self-tappingscrews(5/16
x3/4inch)andlocation
ofthetwo0.290in.holes
throughtheframe
3.Knob
3.
4.Marktheholelocationsonthetractionunitforthe
twomountingbracketholesandfortheholeinthe
controlbracketonthecontrolpanel(Figure5).
5.Usingan0.290inch(sizeL)drillbit,drilltheholes
forthemountingbracketthroughthetractionunit
frame(Figure5).
6.Usinga3/8inchdrillbit,drilltheholeforthe
controlbracketinthecontrolpanel(
Figure5).
7.Installthemountingbracketwiththe2self-tapping
screws(5/16x3/4inch)(
Figure5)
8.Securethecontrolbrackettothecontrolpanelusing
theotherknobandtheretainingplate(insertedfrom
behindthecontrolpanel)(Figure6).
G01 1833
1
2
Figure6
1.Knob2.Retainingplate
9
ProductOverview
Specications
Note:Specicationsanddesignaresubjecttochange
withoutnotice.
Width
47.75inches(121.3cm)
Length
43.2inches(109.7cm)
Height
50.4inches(128cm)
Weight
335lbs(152Kg)
Clearingwidth44inches(111.7cm)
Attachments/Accessories
AselectionofToroapprovedattachmentsand
accessoriesareavailableforusewiththemachineto
enhanceandexpanditscapabilities.Contactyour
AuthorizedServiceDealerorDistributororgoto
www.Toro.comforalistofallapprovedattachments
andaccessories.
Operation
DANGER
Whenthesnowthrowerisinoperation,theimpeller
andaugercanberotatingandcutofforinjure
handsandfeet.
•Beforeadjusting,cleaning,repairingand
inspectingthesnowthrower,andbefore
uncloggingthedischargechute,
mo v e the
auxiliar y h y draulics lev er to the of f position,
stop the engine, and w ait f or all mo ving par ts to
stop .
Removethekey.
•Useastick,
not y our hands
,toremovean
obstructionfromthedischargechute.
•Staybehindthehandlesandawayfrom
thedischargeopeningwhileoperatingthe
snowthrower.
•Keepface,hands,feet,andanyotherpartof
yourbodyorclothingawayfromconcealed,
moving,orrotatingparts.
RefertoyourtractionunitOperator’sManualformore
informationoninstallingandremovingattachments
onyourtractionunit.
Important:Alwaysusethetractionunittoliftand
movetheattachment.
RemovingtheSnowthrower
Note:Toinstallthesnowthrower,refertoSetup.
1.Starttheengineandlowertheattachmenttothe
groundorontoatrailer,thenstoptheengine.
2.Removethechutecontrolbracketasfollows:
•On200/300seriestractionunits,removethe
knobs,washer,andhandleclampfromthechute
controlbracketandremovethebracket.
•OnTXseriestractionunits,removetheknobs
andretainingplatefromthechutecontrol
bracketandremovethebracket.
3.Installthefasteninghardwareonthechutecontrol
bracketforsafekeeping.
4.On200/300seriestractionunits,removethechute
controlcablefromthecableguide.
5.Disconnectthehydrauliclinesandremovethe
snowthrowerfromthemountplate.Refertoyour
tractionunitOperator’sManualforinstructions.
OperatingTips
•Alwaysusefullthrottle(maximumenginespeed).
10
•Ifyourtractionunithasaspeedselector,usethe
slowposition(turtle).
•Ifyourtractionunithasaowdivider,setitas
appropriateforthesnowconditions(i.e.,varythe
settingfrom10o’clockforheavysnowto12o’clock
forlightersnow).
•Thedischargechutecanberotated180°sideto
side.Thedirectioniscontrolledbyturningthe
chutecontrolcrankinthechutecontrolbracket.
•Thechutedeector,ontopofthedischargechute,
canbemovedupanddowntocontroltheheight
anddistancesnowisthrown(
Figure7).
G01 1834
1
2
Figure7
1.Dischargechute
2.Chutedeector
•Removesnowassoonaspossibleafteritfalls.This
producesthebestsnowremovalresults.
•Adjusttheskidstomatchthetypeofsurfacebeing
cleaned;refertoAdjustingSkids.
•Thesnowthrowerisdesignedtocleansnowdown
tothecontactsurface,buttherearetimeswhenthe
frontofthesnowthrowermaytendtorideup.If
thishappens,reduceforwardspeed.
•Dischargesnowdownwindwheneverpossible,and
overlapeachpasstoensurecompletesnowremoval.
Ifwheelsslip,reduceforwardspeed.
•Runthesnowthrowerforafewminutesafter
clearingsnowsomovingpartsdonotfreeze.
•Donotoverloadthesnowthrowerbyclearing
snowattoofastarate.Iftheengineslowsdown,
reduceforwardspeedoradjusttheowdivider
(whereapplicable)tosupplymorepowertothe
snowthrower.
•Insomesnowandcoldweatherconditions,some
controlsandmovingpartsmayfreeze.Therefore,
whenanycontrolbecomeshardtooperate,stopthe
machineandwaitforallmovingpartstostop;then
checkallpartsforfreezeup.Donotuseexcessive
forcewhentryingtooperatefrozencontrols.
Freeallcontrolsandmovingpartsbeforeoperating.
11
Maintenance
RecommendedMaintenanceSchedule(s)
MaintenanceService
Interval
MaintenanceProcedure
Every25hours
•Check/adjustthedischargechute.
Every50hours
•Checktheaugergearboxoil.
Every100hours
•Checktheconditionofthescraperblade.
Beforestorage
•Paintchippedsurfaces.
Yearlyorbeforestorage
•Check/adjustthedischargechute.
•Checktheaugergearboxoil.
•Checktheconditionofthescraperblade.
•Adjusttheskidsasrequired.
CAUTION
Ifyouleavethekeyinthetractionunitignitionswitchwhilethesnowthrowerisattached,someonecould
accidentlystarttheengineandseriouslyinjureyouorotherbystanders.
Removethekeyfromtheignitionanddisconnectthewire(s)fromthesparkplug(s)beforeyoudoany
maintenance,requiringthatthesnowthrowerbeattachedtothetractionunit.Setthewire(s)asidesothatit
doesnotaccidentallycontactthesparkplug(s).
Checking/Adjustingthe
DischargeChute
ServiceInterval:Every25hours
Yearlyorbeforestorage
Ensurethatthechuterotatessmoothlywhenthechute
controlcrankisturned.Ifitdoesnotrotatesmoothly,
adjustthewormgearasfollows:
1.Loosenthewormbracketmountingscrews
(
Figure8),rmlypushingthewormgearagainstthe
teethintheretainingring.
G01 1836
1
2
Figure8
1.Wormbracket2.Wormgear
2.Whileholdingthebracketinplace,tightenthe
mountingscrews.
CheckingtheAugerGearBox
Oil
ServiceInterval:Every50hours
Yearlyorbeforestorage
1.Withthesnowthrowerloweredandonalevel
surface,removethepipeplugfromtheaugergear
box(
Figure9)byplacingtheopenendofa3/8in.
drivesocketextensionovertheplugandusinga
3/8in.openendwrenchonthesquareendofthe
extension.
G01 1835
1
Figure9
1.Pipeplug
2.Checkthelevelofoilinthegearbox.Theoilmust
beatthepointofoverowinginthelleropening.
3.Iftheoillevelislow,addSAE90EPGL-4
transmissionoiltothegearbox.
4.Installthepipepluginthegearbox.
12
ReplacingtheScraperBlade
ServiceInterval:Every100hours—Checkthe
conditionofthescraperblade.
Yearlyorbeforestorage—Checkthe
conditionofthescraperblade.
Thescraperbladecontactsthegroundpreventing
damagetothesnowthrowerhousing.Periodically
inspectthescraperbladeforwear.Whenthescraper
becomesworn,beforetheworkingsurfacecontactsthe
housing,replacethescraperblade.
1.Raisethesnowthrowerafootoffofthegroundand
stoptheengine.
2.Removethenuts,washers,carriagebolts,andscraper
blade(
Figure10).
G01 1838
1
2
3
4
Figure10
1.Nut
3.Carriagebolt
2.Washer
4.Scraperblade
3.Replacethescraperbladeandsecurethenewblade
withthepreviouslyremovedhardware(Figure10).
AdjustingtheSkids
ServiceInterval:Yearlyorbeforestorage
Thedistancebetweenthescraperbladeandtheground
iscontrolledbyskidsoneachsideofthehousing.The
heightcanbeadjustedsothescraperbladewillnotcatch
onunevensurfaces
1.Lowerthesnowthroweruntilitis1to2inches(2.5
to5cm)abovealevelsurface,thenstoptheengine.
2.Removethenuts,washers,andboltssecuringthe
skidstothehousing(Figure11).
G01 1837
1
2
3
Figure11
1.Skid
3.Nuts,washers,andbolts
(boltheadstotheoutside)
2.Housing
3.Positiontheskidsequallyonbothsides,toobtaina
levelscrapingaction,andsecuretheskidswiththe
nuts,washers,andbolts(Figure11).
Note:Onsmooth,pavedsurfaces,thescraperblade
canbeclosetothesurfaceOnuneven,gravelor
crushedrocksurfaces,adjusttheskidstoraisethe
scraper,topreventcatchingorpickinguprocks.
Important:Thescrapershouldbehigher
abovethepavementifthepavementsurfaceson
whichthesnowthrowerwillbeusedarecracked,
rough,oruneven.
13
Storage
1.Beforelongtermstorage,washtheattachmentwith
milddetergentandwatertoremovedirtandgrime.
2.Checktheconditionofthescraperblade.
3.Checktheaugergearboxoillevel.
4.Checkandtightenallbolts,nuts,andscrews.Repair
orreplaceanydamagedorwornpart.
5.Paintallscratchedorbaremetalsurfaces.Paintis
availablefromyourAuthorizedServiceDealer.
6.Storetheattachmentinaclean,drygarageorstorage
area.Coverittoprotectitandkeepitclean.
14
Troubleshooting
Problem
PossibleCauseCorrectiveAction
1.Ahydrauliccouplerisnotcompletely
connected
1.Checkandtightenallcouplers.
2.Ahydrauliccouplerisdamaged.
2.Checkthecouplersandreplaceany
thataredamaged.
3.Thereisanobstructioninahydraulic
hose.
3.Findandremovetheobstruction.
4.Ahydraulichoseiskinked.4.Replacethekinkedhose
5.Theauxiliaryvalveonthetractionunit
isnotopening.
5.Repairthevalve.
Thesnowthrowerdoesnotoperate.
6.Ahydraulicmotorisdamagedorworn.6.Replaceorrepairthemotor.
15
16
G011840
This page may be copied for installation purposes.
17
Notes:
18
Notes:
19
ToroCompactUtilityEquipmentWarranty
AOne-YearLimitedWarranty
CUEProducts
ConditionsandProductsCovered
TheT oro®Companyanditsafliate,T oroWarrantyCompany,pursuant
toanagreementbetweenthem,jointlywarrantyourToroCompactUtility
Equipment(“Product”)tobefreefromdefectsinmaterialsorworkmanship.
Thefollowingtimeperiodsapplyfromthedateofpurchase:
ProductsWarrantyPeriod
Loaders,TrenchersandAttachments1yearor1000operating
hours,whicheveroccursrst
KohlerEngines3years
AllotherEngines2years
Whereawarrantableconditionexists,wewillrepairtheProductatnocost
toyouincludingdiagnosis,labor,andparts.
InstructionsforObtainingWarrantyService
IfyouthinkthatyourToroProductcontainsadefectinmaterialsor
workmanship,followthisprocedure:
1.ContactanyAuthorizedT oroCompactUtilityEquipment(CUE)
ServiceDealertoarrangeserviceattheirdealership.Tolocatea
dealerconvenienttoyou,accessourwebsiteatwww.T oro.com.
YoumayalsocallourToroCustomerCareDepartmenttollfree
at888-865-5676(U.S.customers)or888-865-5691(Canadian
customers).
2.Bringtheproductandyourproofofpurchase(salesreceipt)tothe
ServiceDealer.
3.IfforanyreasonyouaredissatisedwiththeServiceDealer’s
analysisorwiththeassistanceprovided,contactusat:
LCBCustomerCareDepartment
ToroWarrantyCompany
8111LyndaleAvenueSouth
Bloomington,MN55420-1196
TollFree:888-865-5676(U.S.customers)
TollFree:888-865-5691(Canadacustomers)
OwnerResponsibilities
YoumustmaintainyourT oroProductbyfollowingthemaintenance
proceduresdescribedintheOperator’sManual.Suchroutine
maintenance,whetherperformedbyadealerorbyyou,isatyourexpense.
Partsscheduledforreplacementasrequiredmaintenance(“Maintenance
Parts”),arewarrantedfortheperiodoftimeuptothescheduled
replacementtimeforthatpart.Failuretoperformrequiredmaintenance
andadjustmentscanbegroundsfordisallowingawarrantyclaim.
ItemsandConditionsNotCovered
Notallproductfailuresormalfunctionsthatoccurduringthewarranty
periodaredefectsinmaterialsorworkmanship.Thisexpresswarranty
doesnotcoverthefollowing:
•Productfailureswhichresultfromtheuseofnon-Tororeplacement
parts,orfrominstallationanduseofadd-on,modied,orunapproved
accessories
•Productfailureswhichresultfromfailuretoperformrequired
maintenanceand/oradjustments
•ProductfailureswhichresultfromoperatingtheProductinan
abusive,negligentorrecklessmanner
•Partssubjecttoconsumptionthroughuseunlessfoundtobe
defective.Examplesofpartswhichareconsumed,orusedup,during
normalProductoperationinclude,butarenotlimitedto,diggingteeth,
tines,sparkplugs,tires,tracks,lters,chains,etc.
•Failurescausedbyoutsideinuence.Itemsconsideredtobeoutside
inuenceinclude,butarenotlimitedto,weather,storagepractices,
contamination,useofunapprovedcoolants,lubricants,additives,or
chemicals,etc.
•Normal“wearandtear”items.Normal“wearandtear”includes,butis
notlimitedto,wornpaintedsurfaces,scratcheddecalsorwindows,
etc.
•Anycomponentcoveredbyaseparatemanufacturer’swarranty
•Pickupanddeliverycharges
GeneralConditions
RepairbyanAuthorizedT oroCompactUtilityEquipment(CUE)Service
Dealerisyoursoleremedyunderthiswarranty.
NeitherTheToro®CompanynorToroWarrantyCompanyisliable
forindirect,incidentalorconsequentialdamagesinconnectionwith
theuseoftheToroProductscoveredbythiswarranty,including
anycostorexpenseofprovidingsubstituteequipmentorservice
duringreasonableperiodsofmalfunctionornon-usepending
completionofrepairsunderthiswarranty.Allimpliedwarranties
ofmerchantabilityandtnessforusearelimitedtotheduration
ofthisexpresswarranty.Somestatesdonotallowexclusionsof
incidentalorconsequentialdamages,orlimitationsonhowlong
animpliedwarrantylasts,sotheaboveexclusionsandlimitations
maynotapplytoyou.
Thiswarrantygivesyouspeciclegalrights,andyoumayalsohaveother
rightswhichvaryfromstatetostate.
ExceptfortheenginewarrantycoverageandtheEmissionswarranty
referencedbelow,ifapplicable,thereisnootherexpresswarranty.The
EmissionsControlSystemonyourProductmaybecoveredbyaseparate
warrantymeetingrequirementsestablishedbytheU.S.Environmental
ProtectionAgency(EPA)ortheCaliforniaAirResourcesBoard(CARB).
ThehourlimitationssetforthabovedonotapplytotheEmissions
ControlSystemWarranty.RefertotheCaliforniaEmissionControl
WarrantyStatementsuppliedwithyourProductorcontainedintheengine
manufacturer’sdocumentationfordetails.
CountriesOtherthantheUnitedStatesorCanada
CustomerswhohavepurchasedToroproductsexportedfromtheUnitedStatesorCanadashouldcontacttheirT oroDistributor(Dealer)toobtain
guaranteepoliciesforyourcountry,province,orstate.IfforanyreasonyouaredissatisedwithyourDistributor’sserviceorhavedifcultyobtaining
guaranteeinformation,contacttheT oroimporter.Ifallotherremediesfail,youmaycontactusatT oroWarrantyCompany.
374-0261RevA
/
