MULTIPLEX WBK10X Water Booster Pump 00216382 Owner Instruction Manual

Instruction Sheet

Subject: Installation Procedure

Model WBK10X Water Booster Pump,

P.N. 00216382 (220-240 VAC, 50/60 Hz)

1 of 32

 PartNumber020006830 04/23/2018

MULTIPLEX

2100 FUTURE DR, SELLERSBURG, IN 47172

800-367-4233

WWW.WELBILT.COM

Contents

English ...................................................................................................... 1

German .................................................................................................... 7

French ..................................................................................................... 11

Spanish ...................................................................................................15

Italian ......................................................................................................19

Russian ...................................................................................................23

Exploded View .....................................................................................29

Declaration of Conformity ..............................................................31

Read These Before Proceeding:

n

Warning

To Avoid Serious Injury

Read the following warnings before beginning an

installation. Failure to do so may result in possible death

or serious injury.

DO Adhere to all National and Local Plumbing and

Electrical Safety Codes.

DO Turn off incoming electrical service switches when

servicing, installing, or repairing equipment.

DO Check that all flare fittings on the carbonation

tank(s) are tight (8mm). This check should be

performed with a wrench to ensure a quality seal.

DO Inspect pressure on regulators before starting up

equipment.

DO Protect eyes when working around refrigerants.

DO Use caution when handling metal surface edges

of all equipment.

DO Handle CO

2

cylinders and gauges with care.

Secure cylinders properly against abrasion.

DO Store CO

2

cylinder(s) in well-ventilated areas.

DO Use proper protective equipment when

performing maintenance or cleaning on the unit.

DO NOT Throw or drop a CO

2

cylinder. Secure the

cylinder(s) in an upright position with a chain.

DO NOT Connect the CO

2

cylinder(s) directly to the

product container. Doing so will result in an

explosion, causing possible death or injury. Best

to connect the CO

2

cylinder(s) to a regulator(s).

DO NOT Store CO

2

cylinders in temperatures above 125°F

(51.7°C), near furnaces, radiator or sources of heat.

DO NOT Release CO

2

gas from old cylinder.

DO NOT Touch refrigeration lines inside units. Some may

exceed temperatures of 200°F (93.3°C).

NOTE: Water pipe connections and fixtures directly

connected to a potable water supply shall be sized,

installed, and maintained in accordance with Federal,

State, and Local codes.

n

Warning

Disconnect and lock out all electrical power sources

before performing service or maintenance on this

machine – except when electrical tests are being

performed by qualified service personnel.

n

Warning

The appliance is not to be used by persons (including

children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction.

Children must be supervised and are not to play with

the appliance.

2 of 32

PartNumber02000683004/23/2018

Subject: Installation Procedure Model WBK10X Water Booster Pump

ATTENTION: PRESSURE REQUIREMENTS

Max. inlet water pressure: 0.345 MPa (3.45 bar) (50 psi)

Min. inlet water pressure: 0.138 MPa (1.38 bar) (20 psi)

INTRODUCTION

The following instructions cover the installation of a

220VAC,50/60Hz (international) booster. An appropriate

3-wire power receptacle must be located within 6ft (1.8m)

of the Booster Kits.

Unpack the unit from its transportation packaging and

visually check for any signs of damage.

NOTE: Do not plug in Booster Pump Module at this time.

Installation

Important

This booster pump is intended to be installed outside

zone 1 and 2, as specified in IEC 60364-7-701.

The booster pump needs to be installed with a horizontal

distance to possibly spraying water of 1.8 meter. It is not

allowed to install the water booster above or below

(vertically) of possibly spraying water sources.

The water booster has to be installed vertical and NOT

horizontal.

PREPARING THE POWER CORD/MAINS LEAD

INTERNATIONAL UNITS ONLY P.N.00216382

Important

The wires in the power cord/mains lead are colored in

accordance with the following code:

• Green / Yellow = Ground/Earth

• Blue = Neutral

• Brown = Line/Live

1. Locate a 3-terminal plug. This plug (not furnished with

kit) must have a ground-wire-connecting terminal.

2. Locate the loose end of the power cord attached to

the kit. All three (3) wires are stripped to 1/2" (1.3 cm)

length from the end.

3. Connect all three (3) wires to the plug using the

1/2" (1.3 cm) stripped ends or any other terminal

requirements. Different plugs and terminals may

require different stripped lengths.

4. Inspect the cord and plug connection for any loose or

bare wires.

GROUNDING INSTRUCTIONS

The Multiplex Model WBK10X WaterBoosterPump should

be grounded/earthed. In the event of an electrical short

circuit, grounding reduces the risk of electric shock by

providing an escape wire for the electrical current. This

product is equipped with a cord having a grounding/

earth wire with an appropriate grounding plug. The plug

must be plugged into an outlet that is properly installed

and grounded in accordance with all local codes and

ordinances.

n

Warning

Risk of Electric Shock

This kit is supplied with a ground conductor and

grounding-type attachment plug (domestic only). To

reduce the risk of electric shock, be certain that it is

connected only to a properly grounded, grounding-

type receptacle.

NOTE: For 220-240VAC,50/60Hz International Units, a

ground male plug must be supplied at the installation of

the booster pump.

Check with a qualified electrician or serviceman if the

grounding instructions are not completely understood or

if in doubt as to whether the product is properly grounded.

Do not modify the plug provided; if it will not fit the outlet,

have the proper outlet installed by a qualified electrician.

Do not use an extension cord or an adapter plug with this

equipment.

Figure 1

3 of 32

PartNumber02000683004/23/2018

Subject: Installation Procedure Model WBK10X Water Booster Pump

INSTALLING TO A WALL

1. Locate the six (6) 5/16" lag screws and the mounting

bracket.

2. Mount the J-channel to the wall, by using three (3)

screws (provided).

NOTE: Screws must be located in a stud. If mounting to

concrete wall, proper hardware (not provided) must be

used.

3. Mount the booster panel on the wall by raising the

top of the panel over the J-channel. Place the panel

against wall and slide the panel down until it catches

on the J-channel. Mount the bottom of the panel to

the wall by using the remaining two (2) screws (refer to

Figure2).

4. Attach a 1/2" ID water inlet line to the inlet fitting

by using the 1/2" flare elbow with nut and clamp

provided. Then attach another 1/2" ID line to the water

outlet by using the remaining 1/2" flare elbow with nut

and clamp (refer to Figure2).

5. Turn on the main water supply to the booster assembly.

NOTE: Outlet pressure of this assembly is not regulated. A

regulator may be required for certain applications.

6. Plug the power cord into the wall receptacle. The

pump will not begin to run until low water pressure

circuit times out. When the pump cycles “off”, the

gauge should read 0.586 MPa (5.86 bar) (85 psi). Bleed

off water flow until pressure drops to approximately

0.448 MPa (4.48 bar) (65 psi). The pump motor

should begin to run, then turn “off” when pressure

reaches 0.586 MPa (5.86 bar) (85 psi). If not, there are

instructions on the inside of the pressure switch cover

for pressure switch adjustment.

Booster Splash

Guard

J-Channel

Mounting Bracket

Power Cord

#27 Water Inlet

(1/2" Male Flare)

#27 Water Outlet

(1/2" Male Flare)

Mounting

Wall

Water

Booster

Pump

Mounting Screws

Figure 2

4of32

PartNumber02000683004/23/2018

Subject: Installation Procedure Model WBK10X Water Booster Pump

INSTALLING TO A SUPPORT STAND

NOTE: This water booster pump can either be mounted

to the side or on the inside of the support stand. The

method of mounting is the same for either application. The

following instructions cover the side mounting. This stand

is factory assembled to mount the water booster pump on

the left-hand side of the support stand. However, the water

booster can be mounted on the right-hand side by moving

the channel to that side.

,

Caution

If the system has a plate style water filter, it MUST be

mounted to the right-hand side.

1. Locate the mounting hardware supplied with the

support stand: three (3) 1/4"-20 x 1/2" carriage bolts,

two (2) 1/4"-20 x 1/2" hex screws (not supplied), five

(5) 1/4"-20 locking nuts, and the J-channel mounting

plate, (supplied with the water booster). The J-channel

mounting plate will later be mounted to the water

booster pump.

2. With the hook end of the J-channel towards the floor,

mount the channel to the top portion on the side of

the stand.

3. Fasten the channel with three (3) 1/4"-20 x 1/2" carriage

bolts and 1/4"-20 locking nuts. Tighten all bolts

completely.

4. By lifting the back edge of the panel above the channel

and hooking it on the lower edge of the J-channel,

place the water booster pump panel on the J-channel.

5. Attach the lower edge of the water booster pump

panel to the channel on the support stand with two

(2) 1/4"-20 x 1/2" hex screws and 1/4"-20 locking nuts.

Tighten the screws and nuts completely.

6. Complete the remaining installation using the

instructions supplied with the water booster pump.

NOTE: Installer must fit/install a back flow prevention device

compliant with local water regulations in incoming water

supply line.

Booster

Splash Guard

J-Channel

Mounting

Bracket

Model WBK10X

Water Booster

Pump

Multiplex

Support

Stand

Mounting Screws & Nuts

(supplied with support stand)

Figure 3

BEFORE INSTALLING THE WATER BOOSTER PUMP

Incoming

Water

Supply

Coarse

Filter

Accumulator Tank

(optional)

Regulator

0.379 MPa

(3.79 bar)

(55 psi)

Beverage Unit

To

Dispenser

Figure 4

AFTER INSTALLING THE WATER BOOSTER PUMP

Beverage Unit

To

Dispenser

Water

Booster

Pump

Regulator

0.379 MPa

(3.79 bar)

(55 psi)

Accumulator Tank

(optional)

Filter

Coarse

Filter

Backflow

Preventer

Incoming

Water

Supply

Figure 5

5 of 32

PartNumber02000683004/23/2018

Subject: Installation Procedure Model WBK10X Water Booster Pump

Operation

1. Before applying supply water pressure, verify with air

gauge that the bladder pressure (Schrader valve) is

charged to 0.414 MPa (4.14 bar) (60 psi).

2. Turn water supply on, then plug unit into supply power

outlet/mains electrical supply.

3. Verify unit pump comes on and pumps up to 0.586 MPa

(5.86 bar) (85 psi) and then pump goes off.

4. Verify unit pump comes on at 0.448 MPa (4.48 bar)

(65 psi), by expelling water from system.

Annual Cleaning (Trained Service Technician)

A. Isolate or disconnect unit from power source/

mains electrical supply.

B. Remove exterior debris or dirt from unit or its

components using a vacuum cleaner, soft bristle

brush or a nonabrasive towel/rag.

C. Check all electrical connections for condition and

water connections for leaks to ensure safety during

operation. If any issues are found then repairs are

needed before unit can be put back into operation.

D. Reconnect unit to power source/mains electrical

supply.

,

Caution

Before shipping, storing, or relocating this unit, system

must be vented of pressure, drained and cleaned.

n

Warning

If left in a freezing environment with residual water inside

unit/system damage will occur to internal components.

Important

Welbilt recommends that for countries with non-

chlorinated potable water supplies, cleaning of the potable

water supplies should be performed on a 90-day time

interval, or more regularly if required by local legislation.

Cleaning or disinfecting should be performed by using an

environmentally friendly and approved chlorine detergent.

The approved chlorine detergent solution should be

injected into water supply line(s) after any in-line water

filtration systems and flushed through this equipment

to the point of dispense. Thorough flushing through of

the equipment with potable water following cleaning to

ensure no residual chemicals are left in the system.

Tools required for Maintenance or Repair

A. 1/4" (7mm) socket or nut driver

B. 5/16" (8mm) socket or nut driver

C. Standard or Straight Blade Screwdriver

D. Phillips Head Screwdriver

Max Noise dB(A)

Noise emission from this model does not exceed 70 dB(A).

Page is loading ...

29 of 32

PartNumber02000683004/23/2018

Subject: Installation Procedure Model WBK10X Water Booster Pump

WBK10X Exploded View

Page is loading ...

31 of 32

PartNumber02000683004/23/2018

Subject: Installation Procedure Model WBK10X Water Booster Pump

Declaration of Conformity

MULTIPLEX

2100 FUTURE DR, SELLERSBURG, IN 47172

800-367-4233

WWW.WELBILT.COM

PartNumber02000683004/23/2018

Welbilt provides the world’s top chefs, and premier chain operators or growing independents with industry leading equipment and soluons.

Our cung-edge designs and lean manufacturing taccs are powered by deep knowledge, operator insights, and culinary experse.

All of our products are backed by KitchenCare® – our aermarket, repair, and parts service.

CLEVELAND

CONVOTHERM®

DELFIELD®

FITKITCHEN™

FRYMASTER®

GARLAND

KOLPAK®

LINCOLN

MANITOWOC®

MERCO®

MERRYCHEF®

MULTIPLEX®

WWW.WELBILT.COM

MULTIPLEX WBK10X Water Booster Pump 00216382 Owner Instruction Manual

MULTIPLEX WBK10X Water Booster Pump 00216382 Owner Instruction Manual

in other languages

Related papers

Other documents