MIMAKI JFX 200-2513 Operating instructions

MIMAKI ENGINEERING CO., LTD.

https://mimaki.com/

D202563-21

Original instructions

i

CAUTION .............................................................................v

DISCLAIMER OF WARRANTY ....................................... v

Requests ......................................................................... v

FCC Statement (USA) ..................................................... v

Interference to televisions and radios .............................. v

Restriction in use .............................................................vi

Foreword ............................................................................ vii

About usable ink .............................................................vii

On This Operation manual .............................................vii

Safety Precautions .............................................................viii

Symbols .........................................................................viii

Warning labels ................................................................... xiv

Chapter 1 Before Use

About installing this machine .............................................1-2

Where to Install This Machine ..........................................1-2

Working Environmental Temperature ...............................1-2

About fixing machine ........................................................1-3

Moving This Machine ........................................................1-3

Names of Parts and Functions ..........................................1-4

Front Side of the Machine ................................................1-4

Rear Side and Right Side of the Machine ........................1-4

Operation Panel ................................................................1-5

Carriage ............................................................................1-6

Capping station .................................................................1-6

EMERGENCY SWITCH ...................................................1-6

Connecting Cables ............................................................1-7

Connecting USB2.0 Interface Cable .................................1-7

Connecting Power Supply Cable ......................................1-8

Ink bottles ..........................................................................1-9

Replace the ink bottle .....................................................1-12

If the light-blocking cover comes off ...............................1-13

For Ink bottle lamps ........................................................1-14

Ink usage restrictions ......................................................1-14

About ink end and ink near end ......................................1-14

Caution in handling of ink bottles ....................................1-15

Media ...............................................................................1-16

Usable sizes of media ....................................................1-16

Caution in handling of medias ........................................1-16

Chapter 2 Basic Operations

Workflow ............................................................................2-2

Turning the Power ON/OFF ..............................................2-3

Turning the Power ON ......................................................2-3

Turning the Power OFF ....................................................2-4

Setting a Media .................................................................2-5

Setting the Media ..............................................................2-5

Move the irradiation position of the UV lamp .....................2-8

TABLE OF CONTENS

ii

Best-suited position of UV lamp according to printing ......2-8

Positioning method of UV lamp ......................................2-12

Test Printing ....................................................................2-13

Test Printing ....................................................................2-14

Head Cleaning ................................................................2-15

About head cleaning .......................................................2-15

Perform head cleaning depending on the test printing

result ...............................................................................2-15

Printing Data ...................................................................2-16

Starting a Printing Operation ..........................................2-16

Stopping a printing operation halfway .............................2-17

Deleting Received Data (Data Clear) .............................2-17

Move the Y-bar ...............................................................2-18

Chapter 3 Extended Functions

Changing origin .................................................................3-2

Changing origin with JOG keys ........................................3-2

Changing origin with FUNCTION menu ............................3-3

Registering the thickness of the media .............................3-4

Register the thickness of the media manually ..................3-4

Adjust head gap with the or keys ....................................3-4

Measuring the thickness of the media automatically ........3-5

Registering Head gap value .............................................3-6

List of Functions ................................................................3-7

Correct the ink drop position for bidirectional printing .......3-8

PatternCorrect dot position ...............................................3-8

Setting Logical Seek .......................................................3-10

Setting UV mode .............................................................3-11

Perform setting to reduce stripes between passes .........3-12

What is the MAPS Function? ..........................................3-12

Setting MAPS1 Function .................................................3-12

Setting MAPS2 Function (4 color) ..................................3-13

Setting MAPS2 Function (4 color + special color ink) .....3-14

Setting Work Change ......................................................3-17

Setting Ionizer .................................................................3-18

Setting Auto Cleaning .....................................................3-19

Setting nozzle face cleaning time ...................................3-20

Other Settings .................................................................3-21

Machine Settings ............................................................3-22

Setting a AUTO Power-off ..............................................3-22

Setting Time ....................................................................3-23

Setting Units ...................................................................3-24

Setting a KEY BUZZER ..................................................3-25

Setting a LANGUAGE .....................................................3-26

Initializing the Settings ....................................................3-27

Confirming Machine Information .....................................3-28

Check the using status of the machine ...........................3-28

Check the machine version information ..........................3-29

Displaying the Information of this machine .....................3-30

iii

Chapter 4 Maintenance

Maintenance ......................................................................4-2

Precautions for Maintenance ............................................4-2

About Cleaning liquid ........................................................4-2

Maintenance of frame component ....................................4-2

MBIS Maintenance ...........................................................4-3

Cleaning the LM guide ......................................................4-3

Maintaining the Capping Station .......................................4-4

Cleaning the Wiper and Cap ............................................4-4

Cleaning the around station ..............................................4-7

Washing the Ink Discharge Passage (DISWAY WASH) ..4-8

When the Machine Is Not Used for a Long Time

(CUSTODY WASH) ..........................................................4-9

Cleaning the Head and the Area around It ......................4-12

When Nozzle Clogging Cannot Be Solved ......................4-14

Filling with ink from the sub tank to the head .................4-14

Washing of Head nozzle .................................................4-15

Washing of Head nozzle (When Using the PR-200 Washing

Liquid) .............................................................................4-17

If nozzle missing due to color mixture of ink or aeration .4-19

Alternative nozzles for printing, when nozzles missing can not be im-

proved ........................................................................................4-22

Automatic Maintenance Function ....................................4-27

Setting the Refreshing Intervals .....................................4-27

Setting the Cleaning Intervals .........................................4-28

Replacing consumables ..................................................4-29

Replacing the wiper ........................................................4-29

If a Waste Ink Tank Confirmation Message Appears .....4-30

Replacing the waste ink tank before the waste ink tank confir-

mation message is displayed (1) ....................................4-33

Replacing the waste ink tank before the waste ink tank confir-

mation message is displayed (2) ....................................4-34

Refilling antifreeze mixed water ......................................4-35

Refill cooling water .........................................................4-36

Exchange the flushing filter .............................................4-38

If a Flushing Filter Exchange Message Appears ............4-38

Replacing the flushing filter before the replacement message

is displayed .....................................................................4-39

Chapter 5 Troubleshooting

Troubleshooting .................................................................5-2

Power does not turn on ....................................................5-2

The machine does not start printing .................................5-2

Image quality is poor ........................................................5-3

Nozzle is clogged .............................................................5-3

Ink bottle warning appears ...............................................5-4

If a Message “SHAKE WHITE INK BOTLES” Appears ....5-5

If an error related to the sub tank occurs

(Error 618 to 61b) .............................................................5-6

If negative pressure abnormality occurs ...........................5-7

iv

Warning / Error Messages ................................................5-9

Warning messages ...........................................................5-9

Error messages ..............................................................5-12

Chapter 6 Appendix

Specifications ....................................................................6-2

Machine specifications ......................................................6-2

Ink specifications ..............................................................6-3

Order of ink bottles ...........................................................6-4

Sheet for inquiry ................................................................6-5

Function Flowchart ...........................................................6-6

v

CAUTION

DISCLAIMER OF WARRANTY

THIS LIMITED WARRANTY OF MIMAKI SHALL BE THE SOLE AND EXCLUSIVE WARRANTY AND IS IN

LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY

IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS, AND MIMAKI NEITHER ASSUMES NOR

AUTHORIZES DEALER TO ASSUME FOR IT ANY OTHER OBLIGATION OR LIABILITY OR MAKE ANY

OTHER WARRANTY OR MAKE ANY OTHER WARRANTY IN CONNECTION WITH ANY PRODUCT

WITHOUT MIMAKI’S PRIOR WRITTEN CONSENT.

IN NO EVENT SHALL MIMAKI BE LIABLE FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES

OR FOR LOSS OF PROFITS OF DEALER OR CUSTOMERS OF ANY PRODUCT.

Requests

• This Operation manual has been carefully prepared for your easy understanding.

However, please do not hesitate to contact a distributor in your district or our office if you have any inquiry.

• Description contained in this Operation manual are subject to change without notice for improvement.

FCC Statement (USA)

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This equipment generates, uses

and can radiate radio frequency energy and, if not installed and used in accordance with the Operation manual,

may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user

will be required to correct the interference at his own expense.

In the case where MIMAKI-recommended cable is not used for connection of this machine, limits provided by

FCC rules can be exceeded.

To prevent this, use of MIMAKI-recommended cable is essential for the connection of this printer.

Interference to televisions and radios

The product described in this manual generates high frequency when operating.

The product can interfere with radios and televisions if set up or commissioned under improper conditions.

The product is not guaranteed against any damage to specific-purpose radio and televisions.

The product’s interference with your radio or television will be checked by turning on/off the power button of the

product.

In the event that the product is the cause of interference, try to eliminate it by taking one of the following

corrective measures or taking some of them in combination.

• Change the orientation of the antenna of the television set or radio to find a position without reception difficulty.

• Separate the television set or radio from this product.

• Plug the power cord of this product into an outlet which is isolated from power circuits connected to the

television set or radio.

CAUTION

vi

1

2

3

4

5

6

Restriction in use

This machine features high-speed parts, hot parts and UV irradiating parts which need very careful attention. Use

of this machine is limited to the user who understands the risks of inappropriate use completely.

Restriction for user

The user of this machine shall get proper training. Limit to the user those who got proper training to operate this

machine.

Restriction area

• Coming closer to the machine is prohibited for the person other than the user who got proper training. Set up

the restriction area within the range indicated below. You have to install this machine in the dedicated room, or,

set up a fence and make the person recognize that it is a dangerous area.

• If restricting the area with safety fences, set up the safety fences in accordance with the EN ISO13857

standards.

• If installing this machine in a dedicated room, install a lock or interlock on the room’s door, and perform risk

assessment for the final installation place before using the machine.

6,400 mm or more

(252.0 in or more)

1,000 mm

or more

(39.4 in

or more)

1,000 mm

or more

(39.4 in

or more)

1,000 mm or more

(39.4 in or more)

1,000 mm or more

(39.4 in or more)

4,450 mm or more

(175.2 in or more)

vii

Foreword

Congratulations on your purchase of MIMAKI color ink jet printer "JFX200 Series" .

“JFX200 Series” is a UV inkjet printer that can print with UV ink realizing high speed and high image quality.

About usable ink

Usable ink for this machine is LUS-150, LUS-200, LH100, LUS-120,LUS-350 (4-color/ 4-color+white ink / 4-

color+white + clear ink model).

On This Operation manual

• This Operation manual is describing the operations and maintenance of "UV inkjet printer JFX200 Series"

(called as this machine hereafter)

• JFX200-2513 are identical with models IPPR671.

• Read this Operation manual carefully and understand them thoroughly to use.

• This Operation manual has been carefully prepared for your easy understanding, however, please do not

hesitate to contact a distributor in your district or our office if you have any inquiry.

• Descriptions contained in this Operation manual are subject to change without any notice for improvement.

• You can also download the latest manual from our website.

Reproduction of this manual is strictly prohibited.

4-colors version : 2 each of Cyan, Magenta, Yellow and Black color ink bottle are use.

4-colors + White version : One bottle each of yellow and black, and two bottles of cyan, magenta,

white are used.

4-colors + White + Clear version

(LUS150, LH100, LUS120)

: One bottle each of cyan, magenta, yellow and black, and two bottles of

white, clear are used.

4-colors + White + Clear + Primer

version (LUS150, LH100)

: One bottle each of Cyan, Magenta, Yellow, Black, Clear and Primer, and

two bottles of white are used.

6-colors + White version

(only LUS150)

: One bottle each of Cyan, Magenta, Yellow, Black, Light cyan and Light

magenta, and two bottles of white are used.

Depending on the ink type, the available clear ink type differs.

• Please note that other than above combination can not be used.

Ink type Ink type of clear ink

LUS150 LH100

LH100 LH100

LUS120 HUS120

viii

1

2

3

4

5

6

Safety Precautions

Symbols

Symbols are used in this Operation Manual for safe operation and for prevention of damage to the machine.

The indicated sign is different depending on the content of caution.

Symbols and their meanings are given below. Please follow these instructions as you read this manual.

Examples of symbols

Meaning

Failure to observe the instructions given with this symbol can result in death or serious injuries

to personnel. Be sure to read it carefully and use it properly.

Failure to observe the instructions given with this symbol can result in injuries to personnel or

damage to property.

Important notes in use of this machine are given with this symbol. Understand the notes

thoroughly to operate the machine properly.

Useful information is given with this symbol. Refer to the information to operate the machine

properly.

Indicates the reference page for related contents.

The symbol " " indicates that the instructions must be observed as strictly as the CAUTION

instructions (including DANGER and WARNING instructions). A sign representing a precaution

(the sign shown at left warns of hazardous voltage) is shown in the triangle.

The symbol “ ” indicates that it is the forbidden action. If there is a concrete instruction, it is

indicated in or around the symbol “ ”.

The symbol “ ” indicates that the action is forced to be done or the instruction must be

observed. If there is a concrete instruction, it is indicated in the symbol “ ”.

ix

Warning for Use

WARNING

• Be sure to setup the appropriate air-moving system in case of using this machine in a closed room or a room

with bad ventilation.

• The ink used for this machine falls into the category of UN No.3082 and UN Class 9. Since the ink is

flammable, never use fire when using this machine.

• When cleaning the ink station and head, be sure to wear the included safety glasses and gloves.

• If anyone drinks ink or washing liquid in mistake, get the person to vomit and see a doctor immediately.Do not

allow him or her drink vomit.Then, refer SDS about the inquiry.

• If you absorb a lot of vapor and feel bad, immediately move to a location where fresh air is present and then

keep yourself warm and quiet.Then, consult a doctor as soon as possible.

• Discard the waste ink according to the local regulations of the area this unit is used.

• Prevent any leaks into sewage or natural water systems.

• In case of ink leakage, please turn off the main power, unplug the power cable and call for service to our

service or dealer.

Do not disassemble or remodel this machine Handling of ink bottles

• Never disassemble or remodel the main unit of

the printer and the ink cartridge.Disassembling/

remodeling any of them will result in electric

shocks or breakdown of this machine.

• Some of the ingredients (UV Curing initiator)

have toxic consequences to aquatic life.Avoid

leak into water system or sewage containing

water.

• Store ink bottles and waste ink tank in a place

that is out of the reach of children.

• If ink settles on the skin or clothes, immediately

wash it off with detergent or water.If you get ink

in your eyes, immediately wash your eyes with a

lot of clean water for at least 15 minutes. In this

case, also wash the backside of eyelids to rinse

ink away completely. Then, consult a doctor as

soon as possible.

Do not use this machine in damp places

• Avoid damp environments when putting this

machine into service. Do not splash water onto

this machine.Highhumidity or water will give rise

to fire, electric shocks or breakdown of this

machine.

Abnormal event occurs

• If this machine is used under an abnormal

condition where this machine produces smoke

or unpleasant smell, fire or electric shocks can

result.Be sure to turn off the power switch

immediately and detach the plug from the

receptacle.Check first to be sure that this

machine no longer produces smoke, and contact

a distributor in your district for repair.

• Never repair your device by yourself since it is

very dangerous for you to do so.

Grounding work

• Grounding work is necessary to prevent

electrocution accidents when installing an outlet.

• Carry out the grounding work.

Handling of the power cable

• Use a power cable attached to this unit.

• Take care not to damage, break or work on the

power cable.If a heavy matter is placed on the

power cable, heated or drawn, the power cable

can break to cause fire or electric shocks.

Wearing protective devices

• When cleaning parts such as the head, wiper, or

cap, which may scatter ink and washing liquid,

be sure to wear the included safety glasses and

gloves, or ink and washing liquid might enter

your eyes or ink and washing liquid put on your

hands might make your hands rough.

Do not ride on the table

• There is a possibility that the board accuracy

falls. Please never ride on top of the table.

Handling of vacuum

• Never disassemble or remodel the vacuum.

Also, do not touch the relief valve (pressure regulating valve) or

cover the vacuum outlet.

Doing so will decrease the suction power and cause

overheating or malfunction. (Vacuum is placed directly under

the table.)

• High-pitched sounds may occasionally be heard from the

vacuum when the machine is used in a low-temperature

environment, but this is not a fault.

Relief valveVacuum

Safety Precautions

x

1

2

3

4

5

6

WARNING

Power supply and voltage

• This unit contains parts applied high voltage.Carrying out electrical work by those unauthorized for that work is

prohibited.

• Use it with the displayed power supply specifications. The power-supply voltage of this machine shall be

single-phase 200 to 240 Vac 15 A and less. (You cannot use this machine in the 100V system.)

• Be sure to always disconnect the power plug when performing maintenance in order to prevent electrical

shock. Depending on this machine, one minute might be required for condenser discharging time. Be sure to

always wait five minutes or more after disconnecting the power plug before performing any work.

• Be sure to carry out grounding work to prevent electrical shock.

• The main power circuit breaker should be set ON only by personnel with sufficient knowledge about operations

of this unit.

• Do not touch the LED UV unit on or right after the lamp off with bare hands to avoid from burn injury.

Handling the Anti-freezing liquid

• Use the exclusive Anti-freezing liquid by Mimaki ,or the machine may be damaged.

• If the Anti-freezing liquid or Cooling tank water gets on the skin or clothes, immediately wash it off with soap.

If you get the Anti-freezing liquid or Cooling tank water in your eyes, immediately wash your eyes with a lot of

clean water.

Then, consult a doctor as soon as possible.If high temperature Anti-freezing liquid or Cooling tank water gets

on the skin, immediately wash it off with soap and cool with iced water. Then, consult a doctor as soon as

possible.

• Before using the Anti-freezing liquid, be sure to read the Safety Data Sheet (SDS).

• If you swallowed the Anti-freezing liquid or mixed soft water with antifreezing liquid accidentally, try to get to

vomit, and then consult a doctor as soon as possible.

• When unused the Anti-freezing liquid or used Cooling tank water should discard as followings,

 Incinerating the fluid which is absorbed to the sawdust or waste cloth.

 Entrust them to an industrial waste disposal contractor, clarifying their contents.

• Avoid ignition such as static electricity and impact spark.

• Be sure to wear safety glassess and gloves for handling the Anti-freezing liquid.

Handling of LED UV unit

• Do not use the LED UV in an ambience with a possibility of catching fire (gasoline, combustible gas spray,

thinner, lacquer, powder dust, etc.). In addition, do not put paper or cloth near or on the LEDUV, or it may

cause fire.or it may cause electrical shock.

• Never look at the LED UV being lit with your naked eyes,or it may cause pain in your eyes or visual

impairment.Be sure to wear safety glasses.

• Do not apply ultraviolet (UV) light directly to your skin,or it may cause irritation on your skin.

• It is recommended to replace the LED UV unit within the rated life.

Disposition of this machine

• When discarding this machine, request the treatment of it for an industrial waste disposal contractor.

• Treat it properly in compliance with regulation in the local area.

Keep children away

• Keep children away from this machine.

xi

Precautions in Use

CAUTION

Protection against dust Periodic exchange parts

• It is strongly recommended to use this machine

in a room that is not dusty.

• When leaving the workshop after the working

hours, be sure to take off any media from the roll

• hanger.If any media is left on the roll hanger,

dust can put on it.

• Store media in a bag.Wiping off dust

accumulated on a media will adversely affect the

media due to static electricity.

• Dust in the head will also cause drops of ink to

fall abruptly down on the media during printing.If

this phenomenon takes place, be sure to clean

up the head. ( P.2-15)

• There are some parts which must be replaced by

service men.You have to make a contract with

distributors or dealers for after-sale service.

Keep the machine flatly

• Be sure to adjust the level foot to keep the

machine flatly.

Handling of maintenance liquid

• Be sure to store the maintenance liquid in a cold

and dark place.Store the maintenance liquid in a

place that is out of the reach of children.

Warning labels Note on maintenance

• This machine is adhered with a warning label.

Be sure understand firmly the warnings given on

the labels.In the case where any of the warning

label has become so soiled that the warning

message is illegible or has come off, purchase a

new one from your local distributor or our office.

• When cleaning parts such as the head, wiper, or

cap, make sure to wear the attached gloves.

Handling the Anti-freezing liquid Power supply

• Be sure to store the Anti-freezing liquid in a cold

and dark place.

• Store the Anti-freezing liquid in a place that is out

of the reach of children.

• Leave the breaker turned ON.

• Do not turn off the main power switch on the

right side of this machine.

Handling of ink bottles

• Precautions regarding ink are indicated on the Ink bottle. Read these carefully and make sure you understand

the contents before using the product.

• Use the JFX200 genuine ink. Remember that the user shall be filled for a repair to correct any damage

resulting from the use of ink other than the exclusive type.

• The machine does not operate with any ink other than the JFX200 genuine ink.

• Do not use the JFX200 genuine ink with other printers, as doing so may cause damage to such machines.

• Do not refill ink other than the one specified by our company in the bottle. We are not responsible for any

defects caused by your using such an ink.

• If the ink bottle is moved from a cold place to a warm place, leave it in the room temperature for three hours or

more before using it.

• Open the ink bottle just before installing it in the machine. If it is opened and left for an extended period of time,

normal printing performance of the machine may not be ensured.

• Make sure to store ink bottles in a cool and dark place.

• Store ink bottles and waste ink tank in a place that is out of the reach of children.

• Be sure to thoroughly consume the ink in the ink bottle, once it is opened, within three months. If an extended

period of time has passed away after opening the ink bottle, printing quality would be poor.

• Neither pound the ink bottle nor shake it violently, as doing so can cause leakage of ink.

• Do not touch or stain the contacts of the IC chip, as doing so may cause damage to the print circuit board.

• Waste ink is equivalent to waste oil of industrial waste. Request an industrial waste disposal company for

disposal of waste ink.

Safety Precautions

xii

1

2

3

4

5

6

CAUTION

Handling of media

• Use media recommended by MIMAKI to ensure reliable, high-quality printing.

• Pay attention to the expansion and contraction of the media.

Do not use media immediately after unpacking. The media can be affected by the room temperature and

humidity, and thus it may expand and contract. The media have to be left in the atmosphere in which they are

to be used for 30 minutes or more after unpacked.

• Do not use curled media.

The use of curled media can not only cause a media jam but also affect print quality. Straighten the sheet of

media, if significantly curled, before using it for printing. If a regular-sized coated sheet of media is rolled and

stored, the coated side has to face outside.

About UV light About hot parts

• A little UV light leaks from the LED UV unit. UV

light applied to your skin might cause

inflammation and/or skin cancer.Though weak

UV light might cause no inflammation, repeated

exposure to it may lead to chronic

disorders.Avoid applying UV light to your skin

and eyes.

• The LED UV unit and the Post Cure Unit

become very hot. When carrying out

maintenance, wait until the temperature has

been sufficiently lowered after the lamp is turned

OFF.

• Do not touch the parts with the caution label

placed and their vicinity, or burn injury may

occur.

• Possible damage to your eyes due to ultraviolet

is acute disorder (feeling like something is in

your eye, pain and flow of tears) and chronic

disorder (cataract etc.). When using this

machine, take protective measures such as

gloves, long-sleeve cloth, light-resistant mask,

attached light-resistant glasses, etc.

• When it is unavoidable to touch hot parts, be

sure to wear heat-insulating gloves to protect

your hands.

Notes on LED UV unit About cleaning

• When handling the LED UV or the silica glass on

the bottom of the irradiation device, be sure to

wear the gloves attached and never touch them

with bare hands, or the UV ink curing level is

significantly lowered. If the LED UV or silica

glass is contaminated, wipe it with clean gauze

moistened with alcohol.(Do not use alcohol for

cleaning the exterior cover, or the paint will peel

off.)

• After using the unit long time, foreign materials

and dust may be gathered on the conductive

and insulating parts, causing electric

leakage.Periodically clean such parts.

• For cleaning, do not use compressed air

because it scatters foreign materials and dust,

which may cause malfunctions when put inside

the conductive parts.Be sure to use vacuum

cleaner for cleaning of foreign materials and

dust.

• Do not use the unit in a place where there is a

possibility of being wet, or electrical leakage may

occur.

• Electrical leakage, if it should occur, may lead to

electrical shock of personnel or fire.

• In order to prevent accidents from occurring, be

sure to carry out periodic inspections and

replacement of timechange components.

• Never use those UV devices other than those

recommended by Mimaki. We would take no

responsibility for any troubles caused through

the use of a UV devices not recommended by

Mimaki.

About firing and smoking

• Touching hot parts such as the LED UV unit with combustible materials may cause firing and/or smoking.

Leaving combustible materials under the UV LED unit for a couple minutes may also cause firing and/or

smoking.

• After the unit is used long time, foreign materials or dust gathered on the stabilizer or other parts may cause

electrical leakage or insulation deterioration may cause firing and/or smoking.Periodically clean the parts and

measure the insulation resistance, replacing deteriorated parts, if any.

• After the unit is used long time, screws, etc. on the conductive parts may be loosened, causing firing and/or

smoking.Periodically tighten such screws.

• Because this unit is not of explosion proof type,do not use it in an ambience with hazardous materials, or a

possibility of explosion may arise.

• If abnormalities of the unit such as a strange odor, a smoking or a spark burn are found, turn the power off and

call Mimaki immediately.

Safety Precautions

xiii

Cautions on Installation

CAUTION

A place exposed to direct

sunlight

On an inclined surface

A place where temperature or

humidity varies significantly

• Use the machine under the

following environmental

conditions:

• Operating environment:

15 to 30 °C (59 to 86 °F)

35 to 65 % (Rh)

A place that vibrates

A place exposed to direct air

flow from an air conditioner or

the like.

Around a place where fire is

used

A place with much dust A place with chemicals around

xiv

1

2

3

4

5

6

Warning labels

Warning labels are stuck on the machine. Be sure to fully understand the warning given on the labels.

If a warning label is illegible due to stains or has come off, purchase a new one from a distributor or our sales

office.

Affixed under the

belt.

Warning labels

xv

1:Reorder .M909381 2:Reorder .M903330

3:Reorder .M906115 6:Reorder .M902663

7:Reorder .M905980 8:Reorder .M906311

8:Reorder .M906311 8:Reorder .M906311

8:Reorder .M906311

This chapter

describes the items required to understand before use, such as the name of each part of

the machine or the installation procedures.

About installing this machine ........................1-2

Where to Install This Machine ..................... 1-2

Working Environmental Temperature ......... 1-2

About fixing machine ................................... 1-3

Moving This Machine .................................. 1-3

Names of Parts and Functions ......................1-4

Front Side of the Machine ........................... 1-4

Rear Side and Right Side of the Machine ... 1-4

Operation Panel ..........................................1-5

Carriage ...................................................... 1-6

Capping station ........................................... 1-6

EMERGENCY SWITCH .............................. 1-6

Connecting Cables ........................................1-7

Connecting USB2.0 Interface Cable ............1-7

Connecting Power Supply Cable .................1-8

Ink bottles ......................................................1-9

Setting ink bottles ........................................1-9

Replace the ink bottle ................................1-12

If the light-blocking cover comes off ..........1-13

For Ink bottle lamps ...................................1-14

Ink usage restrictions .................................1-14

About ink end and ink near end .................1-14

Caution in handling of ink bottles ...............1-15

Media ..........................................................1-16

Usable sizes of media ................................1-16

Caution in handling of medias ...................1-16

Chapter 1

Before Use

1-2

About installing this machine

Where to Install This Machine

Secure a suitable installation space before assembling this machine.

The place of installation must have enough space for not only this machine itself, but also for the printing

operation.

Working Environmental Temperature

Use this machine in an environment of 15°C (59 °F) to 30°C (86 °F) to ensure reliable printing.

Model Width Depth Height Gross weight

JFX200-2513

4,400 mm

(173.2 in)

2,450 mm

(96.5 in)

1,250 mm

(49.2 in)

650 kg

(1,433 lb)

• A service engineer will perform installation work of this machine. At this time, he/ she will contact you

and explain about the usage and the installation of this machine. After fully understanding that

content, use this machine safely.

• When you usually use photographic fixer, do not install this machine in a room filled with vapor of

photographic fixer. If you install this machine in such a room, ink adhering to the head hardens and it

may cause image quality defect that cannot be improved even if you perform head cleaning many

times and may cause nozzle clogging.

• Besides photographic fixer, if you leave this machine in an environment where acidic vapor (acetic

acid, muriatic acid, etc.) is generated, the same phenomenon occurs.

• Do not use the machine in an environment full of metal cutting fluids or materials containing highly

volatile substances (amines, amine-denatured alcohols). Also, isolate ink, maintenance kits and the

machine from such an environment. This may cause nozzle clogging.

6,400 mm or more

(252.0 in or more)

1,000 mm

or more

(39.4 in

or more)

1,000 mm

or more

(39.4 in

or more)

1,000 mm or more

(39.4 in or more)

1,000 mm or more

(39.4 in or more)

4,450 mm or more

(175.2 in or more)

About installing this machine

1-3

1

Before Use

3

4

5

6

About fixing machine

The leg of this machine has the level foot to fix the machine.

Before turning the power ON, make sure that the printer body is fixed with the leveling feet. The printer body

may start moving during operation if it is not fixed with the leveling feet.

Moving This Machine

• Put the supplied base plate (gray) made of resin between each leveling foot and the floor. To hold the

weight of the printer, using plate is recommended.

• When the machine is moved to any place other than on the same step-free floor, contact your

distributor or our service office.

If you move it by yourself, failure or damage may occur.

Be sure to request your distributor or our service office to move this machine.

1-4

Names of Parts and Functions

Front Side of the Machine

Rear Side and Right Side of the Machine

Operation panel

This panel has the operation keys required for

operating the machine and the LCDs for displaying

setting items, etc.

Waste ink tank

Waste ink gathers in this tank.

Suction valve

Switch at setting media.

Power button

*1

Turns on/off the power to

the machine.

*1: When the power supply button is turned ON, it lights in green, and when it is OFF, it goes out. The ink clogging

prevention function is periodically operated even when the power button is OFF. (Auto maintenance function)

Carriage

The carriage is provided with the

heads for printing.

Y-bar

Moved on the table at printing.

Table

Setting media on it.

There are absorbing holes on the

table so that media is absorbed

when vacuum is ON.

Page is loading ...

MIMAKI JFX 200-2513, JFX200-2513 Operating instructions

Related papers

Other documents