Astria Fireplaces AllumeDLX Instruction Sheet

Brand: Astria Fireplaces

Model: AllumeDLX

Category: Fireplaces

Type: Instruction Sheet

Astria Fireplaces AllumeDLX is more than just a fireplace. It is a fully featured home and outdoors fireplace that combines elegance and functionality to perfection.

With an array of media options and accessories, you can personalize your fireplace to your liking.

It can heat up to 600 square feet so it is perfect for any room in your house, and it comes with adjustable heat settings, so you can always find the perfect temperature.

The AllumeDLX is also incredibly easy to use, with a convenient remote control that gives you control over all of the fireplace's features.

Astria Fireplaces AllumeDLX is more than just a fireplace. It is a fully featured home and outdoors fireplace that combines elegance and functionality to perfection.

With an array of media options and accessories, you can personalize your fireplace to your liking.

It can heat up to 600 square feet so it is perfect for any room in your house, and it comes with adjustable heat settings, so you can always find the perfect temperature.

The AllumeDLX is also incredibly easy to use, with a convenient remote control that gives you control over all of the fireplace's features.

NOTE: DIAGRAMS AND ILLUSTRATIONS ARE REPRESENTATIVE AND ARE NOT DRAWN TO SCALE.

IHP.us.com

pipe joint compounds on ﬂare ﬁttings.

• The burner oriﬁces provided in this

kit are only for use at elevations of

0–4,500 ft (0–1372 m) in the U.S.A.

and Canada. At higher elevations,

the BTU input must be derated by

4% for every 1,000 ft (305 m) to

maintain the proper ratio of gas to

air. If the installer must convert the

unit to adjust for varying altitudes,

a deration information sticker must

be completed by the installer and

attached to the appliance at time of

conversion. Contact your local gas

supplier for deration requirements

for your area.

In Canada:

• The conversion shall be carried out

in accordance with the requirements

of the provincial authorities having

jurisdiction and in accordance

with the requirements of the CAN/

CSA-B149.1 Installation code.

Au Canada:

• La conversion devra être

effectuée conformément aux

recommandations des autorités

provinciales ayant juridiction et

conformément aux exigences du

code d'installation CAN/CSA-B149.1.

KIT CONTENTS

• (1) Brass Burner Oriﬁce

• (1) Pilot Oriﬁce

• (1) SIT Regulator Conversion Kit

• (2) Gas Conversion

Information Labels

REQUIRED TOOLS

• 5/32 in. Allen Wrench

• Torx Bit (T20 with 1/4 in. shank) or

Flat-head Screwdriver

• 1/2 in. Open-End Wrench

Table 1: Gas Conversion Kits

Description Model No. Cat.

No.

Natural Gas to

Propane GCK-SM-LIN60 F3782

GENERAL INFORMATION

Gas conversion kits adapt the appliance

from the use of one type of gas to

another. This kit contains all components

required to complete the conversion,

as well as a self-adhesive label with gas

conversion information to apply to the

appliance rating plate.

• Before installing gas components, apply

pipe joint compound or Teﬂon tape to

all pipe ﬁttings. Always use propane-

resistant joint compounds. Never use

INSTALLATION INSTRUCTIONS FOR GAS CONVERSION KIT GCK-SM-LIN60 FOR USE WITH

ALLUMEDLX60TEN LINEAR DIRECT VENT GAS FIREPLACES WITH SIT PROFLAME 2 SYSTEM

[FIREPLACE MODEL ALLUMEDLX60TEN]

P/N 900927-00 Rev. NC 12/2018

HEARTH PRODUCTS

KITS AND ACCESSORIES

GAS CONVERSION KIT

GCK-SM-LIN60

WARNING

RISK OF PERSONAL INJURY,

DEATH, OR PROPERTY DAMAGE.

This conversion kit shall be installed

by a qualiﬁed service agency in

accordance with the manufacturer’s

instructions and all applicable codes

and requirements of the authority

having jurisdiction. If the information

in these instruction is not followed

exactly, a ﬁre or explosion or

production of carbon monoxide may

result, causing property damage,

personal injury, or loss of life. The

qualiﬁed service agency is responsible

for the proper installation of this

kit. The installation is not proper

and complete until the operation of

the converted appliance is checked

as speciﬁed in the manufacturer’s

instructions supplied with the

kit.The qualiﬁed service agency

performing this installation assumes

responsibility for this conversion.

AVERTISSEMENT

RISQUE DE BLESSURE, MORT OU

DOMMAGE À LA PROPRIÉTÉ

Cette trousse de conversion doit être

installée par un technicien agréé,

selon les instructions du fabricant

et selon toutes les exigences et tous

les codes pertinents de l’autorité

compétente. Assurez-vous de bien

suivre les instructions dans cette

notice pour réduire au minimum

le risque d’incendie, d’explosion

ou la production de monoxyde

de carbone pouvant causer des

dommages matériels, des blessures

ou la mort. Le tecnicien agréé est

responsable de l’installation de

cette trousse. L’installation n’est

pas adéquate ni complète tant que

le bon fonctionnement de l’appareil

converti n’a pas été vériﬁé selon les

instructions du fabricant fournies avec

la trousse. Le fournisseur de service

qualiﬁé ayant réalisé l'installation

assume les responsabilités liées à la

conversion.

CAUTION

RISK OF PERSONAL INJURY OR PROPERTY DAMAGE.

• Never operate ﬁreplace with glass door assemblies removed.

• Securely tighten door latch screws when reinstalling glass door assemblies to

prevent doors from falling out.

• Handle glass door assemblies with extreme care. Replace damaged glass door

assemblies with approved replacement assemblies only.

• The door assemblies contain ceramic glass. Handle with care to prevent

damage. If the door frame or glass becomes damaged, replace the entire glass

door assembly with a manufacturer-approved replacement assembly only. Do

not attempt to substitute any materials used on door assemblies or replace

cracked or broken glass with any other materials.

WARNING

HOT GLASS WILL CAUSE BURNS. DO NOT TOUCH GLASS UNTIL

COOLED.

NEVER ALLOW CHILDREN TO TOUCH GLASS.

• Fireplaces surfaces get EXTREMELY HOT!

• Install only when ﬁreplace is OFF and COLD.

• The glass on the front of the ﬁreplace reaches EXTREMELY HIGH temperatures

and can cause severe burns if touched. Even after the gas is turned off, ﬁreplace

surfaces remain extremely hot.

• Keep children away from an operating ﬁreplace. Closely supervise children in

any room where a ﬁreplace is operating to prevent contact with glass.

INNOVATIVE HEARTH PRODUCTS • ALLUMEDLX LINEAR GAS FIREPLACES WITH SIT PROFLAME • GAS CONVERSION KIT INSTALLATION INSTRUCTIONS

NOTE: DIAGRAMS AND ILLUSTRATIONS ARE REPRESENTATIVE AND ARE NOT DRAWN TO SCALE.

IHP.us.com

WARNING / AVERTISSEMENT

BURN HAZARD. Install only when ﬁreplace is OFF and COLD.

Risque de brûlure. Installer seulement lorsque le foyer est éteint et froid.

CAUTION / ATTENTION

Before proceeding with this conversion, the gas supply must be shut off prior to

disconnecting the electrical power.

Avant de procéder à cette conversion, l’approvisionnement en gaz doit être

coupée avant de débrancher l’alimenta tion électrique.

NOTICE

• Read all steps before starting installation.

• These instructions must be left with the appliance.

• All warnings, precautions, and instructions in the Installation Instructions

and Care and Operation Instructions provided with the appliance also apply to

these instructions.

• If you encounter any problems, need clariﬁcation of these instructions, or are

not qualiﬁed to properly install this kit, contact your local distributor or dealer.

INSTALLATION INSTRUCTIONS

1. Shut OFF the gas supply to the appliance.

2. Disconnect the power supply at the circuit breaker.

3. Remove the optional trim kit (if installed) by gently lifting up and pulling out from

sides of top and bottom trim face to detach it from side face tabs. (see Figure 1).

Positioning

cut-outs

Tabs for

Positioning

Trim Cut-

outs

Figure 1: Removing Optional Trim

4. Lift the barrier to clear the bottom channel and swing the bottom of the barrier out. Then

lower the barrier to clear the top channel.

Upper Front Face

Barrier Channel

Bottom Front Face

Barrier Channel

Push UP Barrier Top to

slide up then slide Down

pulling OUT

Bottom Front Face

Screen Barrier

Figure 2: Removing Screen Barrier

5. Detach the four (4) door latches on top

of ﬁrebox.

6. Swing the top of the glass door away

from the ﬁreplace at about 15° angle.

(see Figure 3).

7. Carefully grip the door at the top and

bottom, and remove it from the ﬁreplace.

Place the door in a safe location for later

reinstallation.

8. Remove access control door from

rectangular opening in front of the glass

door by lifting it up from the bushings

and pulling up to release the tabs from

slots on side retaining brackets. Set

aside the access control door for later

reinstallation (see Figure 4).

9. If ﬁreplace has not been installed,

remove nine (9) screws holding the

bottom front ﬁreplace face to have

better access to the ﬁreplace control

(Figure 4).

Glass Door

4 Door Latches

Figure 3: Removing Glass

Door Assembly

10. Remove the media (if installed),

following the instructions provided

with the Media Kit, set media aside

for later reinstallation.

11. Remove the eight (8) 5/16 in. screws

securing the pan media (see Figure

5, page 3) Set aside the screws and

pan assembly in a secure location

for later reinstallation.

12. Remove two (2) screws holding the

pilot assembly.

13. Remove the eight (8) 5/16 in. screws

securing the burner assembly (see

Figure 5, page 3).

INNOVATIVE HEARTH PRODUCTS • ALLUMEDLX LINEAR GAS FIREPLACES WITH SIT PROFLAME • GAS CONVERSION KIT INSTALLATION INSTRUCTIONS

NOTE: DIAGRAMS AND ILLUSTRATIONS ARE REPRESENTATIVE AND ARE NOT DRAWN TO SCALE.

IHP.us.com

Access Control Door

Bottom Face

Removed

Remove 9 screws

holding Bottom

Face

Figure 4: Accessing the Control Compartment

Pilot

Screws

Holding

the burner

Assembly

(Qty. 8)

Screws holding

Pilot Assembly

Air Shutter

Lever

Pan

Media

Screws holding

the Pan Media

(Qty. 8)

Control

Access Pilot Shield

Burner

Figure 5: Removing Pan Media and Burner Assembly

14. Carefully rotate the burner towards the front to disengage the air shutter lever and slide the burner to the left, to clear the venturi

from the oriﬁce. Then, lift the burner and take it out of the ﬁreplace (see Figure 5). Set aside the screws and burner assembly in

a secure location for later reinstallation.

INNOVATIVE HEARTH PRODUCTS • ALLUMEDLX LINEAR GAS FIREPLACES WITH SIT PROFLAME • GAS CONVERSION KIT INSTALLATION INSTRUCTIONS

NOTE: DIAGRAMS AND ILLUSTRATIONS ARE REPRESENTATIVE AND ARE NOT DRAWN TO SCALE.

IHP.us.com

IMPORTANT!

• Use pipe joint compound or

Teﬂon tape on all pipe ﬁttings

before installing.

• Use propane-resistant compounds

in propane applications.

• Do NOT use pipe joint compounds

on ﬂare ﬁttings.

22. Loosen shutter cap set screw before

the shutter opening can be adjusted

with the shutter lever (Figure 10).

23. Install the air shutter adjustment

lever (see Figure 10).

24. Place the burner assembly into

position, taking care to ensure the

air shutter clears the pilot bracket.

Replace the screws securing the

burner to the burner brackets.

25. Turn ON the gas supply to the

ﬁreplace and relight the appliance.

With the main burner ON, use a gas

leak test solution to test the new

pressure regulator assembly and all

gas line joints for leaks.

26. Attach the conversion information

label to the back side of rating plate,

(see Figure 11, page 5).

27. Using a long thin ﬂat screwdriver

loosen plug screws on valve (Figure

7).Using a manometer, test the inlet

and manifold gas pressures. Gas

supply pressure requirements are

listed in Table 3 and Table 4, page 5.

NOTE: Always test pressures with

the valve regulator control at the

highest setting.

28. Reinstall the control compartment

access door (see Figure 4, page 3).

29. Verify appliance operation.

30. Reinstall the media (if applicable),

glass door assembly, screen barrier

and trim kit (if applicable).

31. Relight the main burner and verify

proper burner ignition and operation.

32. Inspect the pilot system for proper

ﬂame. The pilot ﬂame should engulf

the ﬂame sensor, as shown in Figure

12, page 5.

20. Verify the new burner oriﬁce is the

correct size. See Table 2 for oriﬁce

sizes and Figure 8 for an illustration

of the oriﬁce.

NOTE: The new oriﬁces are attached

to the back cover of this manual.

Table 2: Burner Oriﬁce Size—

0–4500 ft (0–1372 m)

Fireplace

Model

Natural Gas

drill size

(inches)

Propane

drill size

(inches)

ALLUMEDLX60TEN #30 (0.1285 in.)*

Cat. No. J6988

#49 (0.073 in.)**

Cat. No. J6989

* Standard size installed at factory.

** Available as ﬁeld conversion only.

size

Figure 8: Burner Oriﬁce

21. Remove the existing burner oriﬁce

and replace it with the provided

oriﬁce. Use pipe joint compound

or Teﬂon® tape when installing

the oriﬁce (Figure 9).

15. Refer to Figure 7 and the

instructions provided with the SIT

regulator conversion kit. Using a

Torx T20 driver with a 1/4 in. shank,

or ﬂat-head screwdriver, remove

and discard the two (2) pressure

regulator mounting screws, the

pressure regulator tower, the

diaphragm assembly (if applicable),

and the spring. Ensure the rubber

gasket installed on the back of the

replacement pressure regulator is

properly positioned.

16. Install the new stepper motor

pressure regulator assembly using

the supplied screws. Tighten the

screws to 25 lb-in.

17. Attach the enclosed identiﬁcation

label to the valve body where it can

be easily seen.

18. Make stepper motor and valve

electrical connections.

19. Remove the pilot hood assembly to

access the hex-head pilot oriﬁce.

Using a 5/32 in. Allen wrench,

remove and replace the pilot oriﬁce

with the one provided with the kit

(see Figure 6).

NOTE: Use extreme care to avoid

damaging the igniter assembly.

Pilot

Oriﬁce

Pilot

Hood

Figure 6: Installing the Pilot Oriﬁce

Orange Wire

(from DFC Wire

Harness)

Pressure Regulator

Tower

Main Gas Inlet

3/8" NPT

Green Wire

(from DFC Wire Harness)

Line (IN) Test Port

Manifold (OUT) Test Port Connect GTMS

wire harness.

Yellow Ground Wire

(from DFC Wire Harness)

Figure 7: SIT Proﬂame Gas Valve

Using a

Wrench,

Hold elbow

Using another,

Wrench, re-

move/Replace

Oriﬁce

Figure 9: Burner Oriﬁce

Air Shutter

Screw Cap

50°

Air Shutter

Lever

Figure 10: Loosening Shutter Screw

Cap

INNOVATIVE HEARTH PRODUCTS • ALLUMEDLX LINEAR GAS FIREPLACES WITH SIT PROFLAME • GAS CONVERSION KIT INSTALLATION INSTRUCTIONS

NOTE: DIAGRAMS AND ILLUSTRATIONS ARE REPRESENTATIVE AND ARE NOT DRAWN TO SCALE.

IHP.us.com

Apply New Conversion

Labels

Existing

Rating

Label

Rating

Plate

Figure 11: Apply Conversion Labels

Pilot Hood

Igniter Rod

Flame

Sensor Pilot

Nozzles

Figure 12: Pilot Flame Appearance

NOTE: For complete lighting

instructions, see the lighting label in

the appliance control compartment

or in the Care and Operation

Instructions provided with the

appliance.

33. Turn OFF the gas supply to the

ﬁreplace.

34. Disconnect the manometer. Using

a long thin ﬂat screwdriver tighten

plug screws on valve.

Table 3: Inlet Gas Supply Pressures

Fuel # Minimum Maximum

Natural Gas 5.0 in. WC

(1.25 kPa)

10.5 in. WC

(2.61 kPa)

Propane 11.0 in. WC

(2.74 kPa)

13.0 in. WC

(3.23 kPa)

Table 4: Manifold Gas Supply Pressures

Fuel # Low High

Natural Gas 1.6 in. WC

(0.4 kPa)

3.5 in. WC

(0.87 kPa)

Propane 6.3 in. WC

(1.57 kPa)

10.0 in. WC

(2.49 kPa)

Table 5: BTU Inputs

Fuel # Input (BTU/Hr)

MAX. MIN

Natural Gas 47,000 32,000

Propane 41,000 32,000

35. Turn ON the gas supply to the

ﬁreplace. Use a gas leak test solution

to test the NPT plugs for leaks.

CAUTION

• Air shutter adjustment should

only be performed by a qualiﬁed

professional service technician.

• Soot will be produced if the

air shutter is closed too much.

Any damage due to carboning

resulting from improperly setting

the air shutter is not covered

under the warranty.

36. Read "Flame Appearance

and Sooting" and "Air Shutter

Adjustment Guidelines" before

proceeding. Before adjusting the

air shutter, allow the burner to

operate for at least 30 minutes while

continuously observing the ﬂame.

37. Adjust the air shutter using the

lever located just under the door,

slightly right of center (see Table 6).

See Figure 13 for proper ﬂame

appearance.

• To INCREASE air shutter gap, pull

the lever toward front of ﬁreplace.

• To DECREASE air shutter gap,

push the lever toward back of

ﬁreplace).

• If the ﬂame appears weak or sooty,

pull lever toward back of ﬁreplace

until proper ﬂame appearance is

achieved.

• If ﬂame stays lowered blue, push

lever toward back of ﬁreplace

until proper ﬂame appearance

is achieved.

Flame Appearance and Sooting

Proper ﬂame appears blue at the base

and becomes yellow-orange in the body

of the ﬂame. When the appliance is ﬁrst

lit, the entire ﬂame may be blue and will

gradually turn yellow-orange during the

ﬁrst 30 minutes of operation. After 30

minutes of operation, if the ﬂame is blue,

or if the ﬂame is orange with evidence

of sooting (black tip), the air shutter

opening may need to be adjusted.

If the air shutter opening is closed too

far, sooting may develop. Sooting is

indicated by black puffs developing at

the tips of very long orange ﬂames.

Sooting results in black deposits forming

on the logs, interior appliance surfaces,

and on exterior surfaces adjacent to the

vent termination.

Sooting is caused by incomplete

combustion in the ﬂames and lack of

combustion air entering the air shutter

opening. To achieve a warm yellow-

orange ﬂame with an orange body that

does not soot, the shutter opening must

be adjusted between these two extremes.

Air Shutter Adjustment Guidelines

• If smoke or soot is present, push

the lever IN to increase the air

shutter gap.

• The more offsets in the vent system,

the larger the air shutter opening will

need to be.

• An appliance operated with the

air shutter opened too far, may

have ﬂames that appear blue and

transparent.

• Propane models may exhibit ﬂames

that candle—or appear stringy.

If this condition is present and

persists, adjust the air shutter to a

more OPEN position. Then operate

the appliance for a few more minutes

to ensure that the ﬂame normalizes

and the ﬂames do not appear sooty.

Table 6 is provided to aid in achieving

the correct air shutter adjustment.

Table 6: Air Shutter

Adjustment Guidelines

Amount of

Primary Air Flame

Color Air Shutter

Adjustment

If air shutter is

closed too far...

... ﬂame will

be orange.

Air shutter gap should

be increased:

Pull lever toward front

of ﬁreplace.

If air shutter is

open too far...

... ﬂame will

be blue.

Air shutter gap should

be decreased:

Push lever toward back

of ﬁreplace.

Gas Flex

tube

Air Shutter

Adjustment Lever

Figure 13: Burner Flame Appearance

Table 7: Main Shutter Opening

Model Natural

Gas Propane/

ALLUMEDLX60TEN 1/8"

(3.18mm) Fully Open

INNOVATIVE HEARTH PRODUCTS • ALLUMEDLX LINEAR GAS FIREPLACES WITH SIT PROFLAME • GAS CONVERSION KIT INSTALLATION INSTRUCTIONS

NOTE: DIAGRAMS AND ILLUSTRATIONS ARE REPRESENTATIVE AND ARE NOT DRAWN TO SCALE.

IHP.us.com

______________________________________________________

NOTES

INNOVATIVE HEARTH PRODUCTS • ALLUMEDLX LINEAR GAS FIREPLACES WITH SIT PROFLAME • GAS CONVERSION KIT INSTALLATION INSTRUCTIONS

NOTE: DIAGRAMS AND ILLUSTRATIONS ARE REPRESENTATIVE AND ARE NOT DRAWN TO SCALE.

IHP.us.com

______________________________________________________

NOTES

INNOVATIVE HEARTH PRODUCTS • ALLUMEDLX LINEAR GAS FIREPLACES WITH SIT PROFLAME • GAS CONVERSION KIT INSTALLATION INSTRUCTIONS

NOTE: DIAGRAMS AND ILLUSTRATIONS ARE REPRESENTATIVE AND ARE NOT DRAWN TO SCALE.

IHP.us.com

ALLUMEDLX ORIFICE AND LABEL

[Staple oriﬁce and conversion labels here]

1769 East Lawrence Street • Russellville, AL 35654

P/N 900927-00 Rev. NC 12/2018

Innovative Hearth Products reserves the right to make changes

at any time, without notice, in design, materials, speciﬁcations,

prices and also to discontinue colors, styles, and products.

Consult your local distributor for ﬁreplace code information.

Astria Fireplaces AllumeDLX Instruction Sheet

Brand: Astria Fireplaces

Model: AllumeDLX

Category: Fireplaces

Type: Instruction Sheet

Astria Fireplaces AllumeDLX is more than just a fireplace. It is a fully featured home and outdoors fireplace that combines elegance and functionality to perfection.

With an array of media options and accessories, you can personalize your fireplace to your liking.

It can heat up to 600 square feet so it is perfect for any room in your house, and it comes with adjustable heat settings, so you can always find the perfect temperature.

The AllumeDLX is also incredibly easy to use, with a convenient remote control that gives you control over all of the fireplace's features.

Download PDF

report

Astria Fireplaces AllumeDLX Instruction Sheet

Astria Fireplaces AllumeDLX Instruction Sheet

Related papers

Other documents