Interlogix 6250FM Series Installation guide

Brand: Interlogix

Model: 6250FM Series

Type: Installation guide

Sentrol 6250FM Series

Flush Mount SureShot PIR

Installation Instructions

Models 6255FM, 6257FM

Single gang box

(not included)

Masking kit

Sliding LED cover

Flush mount cover plate

Lens

LED

Tamper switch

(6257FM only)

Terminal block

Mounting screws

Note: The masks have two notches to prevent incor-

rect installation. One notch matches a rib in the

front cover. The second notch matches a dimple

in the lens.

Avoid False Alarm Sources

Sunlight or

reflected sunlight

Pets

Intermittent

heat sources

Hot or cold air

directed onto sensor

For false-alarm-free operation, a PIR should not “see"

sources of heat or cold.

Masking

1. Choose the mask you need, if any.

2. Press in on side latches of unit and pull the back cover

off.

3. Insert the mask behind lens on front cover by pressing

over four mounting pins. Once back cover is snapped

back on, the mask will be held tight against the lens.

4. Replace back cover and proceed with mounting.

The unit can be mounted into a standard single gang

electrical box, a remodel single gang box, or a rough-in

plate. It can be mounted in the wall or on the ceiling. The

following directions apply to any of the above.

1. Feed wire through the single gang box or rough-in plate

and hook up to the terminals on the back of the unit.

2. Connect wires per “wiring” diagrams on following pages.

3. Tie the wire to the strain relief hanger on the back of the

unit using the tie wrap provided in the box.

4. Place the cover plate over the unit and set into the single

gang box or rough-in plate.

5. Tighten screws on the cover plate.

6. After walk testing, the LED cover can be slid up to cover

the LED.

Side Latches

Terminal Block

Strain Relief

Hanger

SIDE VIEW

Installing the Flush Mount Sureshot

Note: When mounting on the ceiling, align the unit to

maximize the oblong detection pattern for the

room.

Always use “center spot” mask when

mounting on ceiling.

Note: To correctly mount the Pet Alley Mask, the lens

must be removed from the front cover and

rotated 180

Mounting

WIDE

ANGLE

Align notch

with dimple

Align

notch

with rib

Inside of

front cover

Align notch

with dimple

Inside of

front cover

Rotate

lens 180°

PET

ALLEY

ROTATE LENS

180

Capture zone

at 8' mounting height

20'

15'

ZONE PATTERNS

With "Vertical Barrier" MaskWall Mount–No Mask

With "Pet Alley" Mask

Strip back the outer jacket on your wiring cable. This will

allow wires to flex in the case. Use cable strain relief built

into back cover to prevent stressing wires at their connec-

tion.

With "Single Spot" Mask

Wiring

1 Zone

2 Beams

29 Zones

58 Beams

7 Zones

14 Beams

7 Zones

14 Beams

With "Wide Angle" Mask

Side View

18 Zones

36 Beams

Side View

29 Zones

58 Beams

Ceiling Mount–Center Spot Mask

Capture

Zone

25' diameter (7.5m)

coverage pattern

8' (2.4m)

Note: Intruder must enter capture zone in order to be detected. False alarm sources,

such as heaters, should be kept out of the coverage pattern. Be sure to insert center

spot mask to reduce potential for false alarms.

15' (4.59m) X 20' (6.12m)

capture zone

Note: The unit should be connected to a UL listed power

supply, capable of providing four hours of standby power.

Side View

30'

9.14m

40'

12.19m

38.4°

2.13m

10'

3.04m

20'

6.09m

30'

9.14m

40'

12.19m

+54°

+38.4°

+18°

54°

20°

0°

54°

38.4°

20°

90°

30'

(9.14m)

40'

(12.19m)

40'

12.19m

2.13m

10°

40'

12.19m

0' 40'

12.19m

2.13m

7°

Top View

10'

3.04m

30'

9.14m

20'

6.09m

Top View

5.9°

Top View

10°

40'

12.19m

0' 40'

12.19m

10'

3.04m

20'

6.09m

30'

9.14m

2.13m

Top View

Side View

Note: Lens must be

inverted for pet alley

90°

30'

9.14m

40'

12.19m

.91m

40'

12.19m

Side View

10'

3.04m

20'

6.09m

30'

9.14m

Top View

30'

9.14m

20'

6.09m

10'

3.04m

–

Power-In

7 to 16 VDC

Power-In

7 to 16 VDC

6255FM Model

6257FM Model

NC COM

N O C OM T/ NO Ta mp

NOTE: This unit will fit in most standard single gang electrical boxes or

rough-in plates, available at any electrical supply store.

SPECIFICATIONS

FEATURES

Pulse Count......................... Bi-directional, 1 zone (2 pulses)

with Motion Verification

Capture Zone (at 70½ F)

Wide Angle (90½) ................... 30' (9.14m) x 30' (9.14m)

Single Spot...................................... 40' (12.19m) range

Vertical Barrier ................................. 40' (12.19m) range

Pet Alley (90½) ................................... 30' (9.14m) range

360°Ceiling ...... 15' x 20' (4.57m x 6.10m) at 8' (2.44cm)

mounting height

....... 16' x 30' (4.88m x 9.14m) at 12' (3.65m)

mounting height

....Ceiling mounting height up to 12' (3.65m)

Mounting ............................................ Wall, corner, or ceiling

LED indicator............................................................Walktest

Size ...................................................... 2.75" (6.99cm) Width

4.50" (11.43cm) Height

1.63" (4.13cm) Total Depth

1.37" (3.49cm) Depth behind wall

0.25" (0.64cm) Depth in front of wall

Color .................................................................. White/White

ELECTRICAL

Voltage ............................................................... 7 to 16 VDC

Current ............................................8 mA typical, 10mA max.

Maximum relay rating .....................................16VDC, 50 mA

Alarm output ............. Fail safe contacts w/ 10 ohms in series,

6255FM - Form A, Normally Closed (NC)

6257FM - Form C, Normally Closed and Open (SPDT)

Alarm duration................................................ 2 to 5 seconds

Cover tamper contacts................................Normally Closed,

rating: 50 mA, 12VDC

(6257FM only)

ENVIRONMENTAL

Operating Temperature........... 0°F to 120°F (-17°C to +50°C)

Humidity ................................... 10% to 90% noncondensing

RFI immunity ...... greater than 10V/meter from 0 to 1000MHz

Side View

2.75"

6.99 cm

4.50"

11.43 cm

Front View

ORDERING INFORMATION

PART LOOP ELECTRICAL COMMENTS LISTING

NUMBER TYPE CONFIGURATION

6255FM Normally Closed N.C. – Form A No Tamper UL

6257FM Normally Closed or Open SPDT (N.C. and N.O.) – Form C Incl. Tamper UL

12345 SW Leveton Dr.

Tualatin, OR 97062

Tel.: 503.692.4052 Fax:

503.691.7566

U.S. & Canada: 800.547.2556

Technical Service: 800.648.7424

FaxBack: 800.483.2495

CORPORATE HEADQUARTERS

Sentrol reserves the right

to change specifications

without notice.

SENTROL

13048 Rev. B 06/00

Static/lightning immunity............. 2.5KV, 2 joules max energy

impulse, 1 msec rise / 50 msec decay

4.5"

11.43 cm

1.63"

4.13 cm

.25"

0.64 cm

1.37"

3.49 cm

Interlogix 6250FM Series Installation guide

Interlogix 6250FM Series Installation guide

Interlogix 6250FM Series Installation guide

Related papers

Other documents