Aventura FBR-8FE1LX-SFP User manual

Brand: Aventura

Model: FBR-8FE1LX-SFP

Category: Network media converters

Type: User manual

AventuraTechnologies

180AdamsAvenue

Hauppauge,NY11788

(877)707‐9600

www.aventuratechnologies.com

Instruction Manual

SFP Based, 10/100 Ethernet, 9-Port Unmanaged Switch / Media

Converter

Model Numbers:

FBR-8FE1LX-SFP – SFP Based, 10/100 Mbps Ethernet, 9-Port Unmanaged Switch /

Media Converter

INSTALLATION AND OPERATION INSTRUCTIONS

FUNCTIONAL DESCRIPTION

The FBR-8FE1LX-SFP is a nine-port unmanaged switch, with eight UTP 10/100 Ethernet interfaces

and one SFP based 1000Mbps optical interface. The unit uses industry standard Small Form-Factor,

Pluggable (SFP) modules for connecting to the fiber media. A proper Aventura Technologies approved

SFP module is selected by the customer to accommodate the type and number of fibers, as well as the

transmission distance.

The FBR-8FE1LX-SFP switches data packets between eight 10/100base-T/TX Ethernet ports and a

1000Mbps optical fiber port, based on the destination address in each data packet.

The FBR-8FE1LX-SFP is configured to auto-negotiate the data rate on any UTP Ethernet port to either

10 or 100 Mbps, and operating mode to either full or half-duplex. Additionally, the unit is configured to

perform the MDI/MDIX sensing and switching automatically. This feature allows for the use of

standard, straight through patch cords, without regard to the configuration (MDI or MDIX) of the device

the FBR-8FE1LX-SFP unit is connected to.

The data rate on the optical port of the FBR-8FE1LX -SFP is always 1000Mbps, full-duplex.

This unit is contained in a compact and rugged steel housing with internal dc voltage regulation. The

detachable terminal block and LED indicators provide for easy installation and monitoring of Ethernet,

optical link, and dc power status.

The unit operates as either a surface mounted, modular, stand-alone device, or within a rack mounted

card cage.

INSTALLATION

THE INSTALLATION OF THIS UNIT SHOULD BE MADE BY A QUALIFIED SERVICE

PERSON(S) AND MUST CONFORM TO ALL LOCAL CODES.

The physical outline and front/rear panel configuration of the unit is detailed in Figure 2.

Mount the unit to a secure surface using #8 (3mm) hardware in two places. See Figure 3 for a full size

mounting template. Be sure to allow sufficient room for the required minimum bend radius of the fiber

cable used.

POWER SOURCE

The unit requires a +12VDC power source for proper operation. The DC input is diode protected against

reverse polarity connection.

In the USA and in Canada, for standalone surface mounted installation, an Aventura Technologies FBR-

PSUS12DC1A is supplied with this unit. Contact Aventura Technologies for ordering power supply

units for use in countries other than the USA and Canada.

When installed in a rack mounted card cage, the power for the unit is supplied from the card cage’s

power supply.

POWER CONNECTION

Power is supplied to the unit via a two-pin terminal block connector. Follow the labeling on the unit for

proper connections of the +12 volt dc and ground leads.

ETHERNET CONNECTION

The UTP Ethernet connections are made via the eight RJ-45 connectors on the front of the unit. For

proper operation, the use of a patch cord and/or cable rated Category-5 or better is required.

FIBER CONNECTION

The fiber optic connections vary, depending on the selection of SFP module. Refer to the instructions

supplied with the SFP module for the proper procedure of installing the SFP module in the FBR-

8FE1LX-SFP unit, as well as for the proper procedure for connecting the fiber to the SFP module.

STATUS INDICATORS

Each unit provides the following LED status indicators to aid in installation and troubleshooting:

POWER INDICATOR

A bi-color LED indicator monitors the voltage at the unit’s input connector and the operating internal

voltage of the module. The power status associated with this indicator is summarized below.

Power Indicator Power Status

Green Proper Input Voltage Present – Proper Internal Operating Voltage Present

Red Proper Input Voltage Present – Internal Operating Voltage Faulty

Off No Input Voltage Detected

OPTICAL LINK INDICATOR

A bi-color LED indicator monitors the power of, and proper synchronization with the optical input

signal that is being received at the FBR-8FE1LX-SFP. The optical link status associated with this

indicator is summarized below.

Optical Link Indicator Optical Status

Green Proper Optical Input Present

Red Optical Input Not Detected

Off Check Power Supply

ETHERNET INDICATORS

Two LED indicators on the RJ-45 connector of the FBR-8FE1LX-SFP unit monitor the status and

operating mode of the Ethernet link. The Ethernet status associated with these indicators is summarized

below.

Ethernet Indicators Ethernet Status

Speed

(GREEN)

Lit: Link operating at 100Mbps

Unlit: link operating at 10Mbps or no link

Link/Activity

(GREEN)

Lit: Good link on the port

Blinking: The port is receiving/transmitting data

Unlit: No link

Device Compatible With (Depending on SFP Module Selection)

FBR-8FE1LX-SFP FBR-1GE1LX-SFP-MINI

FBR-1GE1LX-SFP

FBR-2X1GE1LX-SFP

FBR-1GE2LX -SFP

FBR-8FE1LX-SFP

Figure 1 – List of Compatible Devices

Figure 2 – Physical Outline And Front/Rear Panel Configuration Of Units

Figure 3 – Surface Mounting Template (1:1)

LIMITED LIFETIME WARRANTY INFORMATION

This limited lifetime warranty applies only to the original end user customer of the product for so long

as the original end user customer owns the product. This limited warranty is non-transferable.

Damage due to shipping the products to you is covered under this limited warranty. Otherwise, this

limited warranty does not cover damage due to external causes, including accident, abuse, misuse,

problems with electrical power, servicing not authorized by Aventura Technologies, Inc., usage not in

accordance with product instructions, failure to perform required preventive maintenance, and problems

caused by use of parts and components not supplied by Aventura Technologies, Inc.

During the warranty period beginning on the invoice date, Aventura Technologies, Inc. will repair or

replace products covered under this limited warranty that are returned to Aventura Technologies, Inc.'s

facility. To request limited warranty service, you must contact Aventura Technologies, Inc.'s Customer

Technical Support within the limited warranty period. Refer below to find the appropriate contact

information for obtaining customer assistance. If limited warranty service is required, Aventura

Technologies, Inc. will issue a Return Material Authorization Number. You must ship the products back

to Aventura Technologies, Inc. in their original or equivalent packaging, prepay shipping charges, and

insure the shipment or accept the risk of loss or damage during shipment. Aventura Technologies, Inc.

will ship the repaired or replacement products to you freight prepaid if you use an address in the

continental United States, where applicable. Shipments to other locations will be made freight collect.

To view the full terms of the warranty, please go to: www.ati247.com

SERVICE INFORMATION

There are no user serviceable parts inside the unit.

In the event that service is required to this unit, please direct all inquiries to:

Aventura Technologies, Inc.

180 Adams Avenue Phone: (631) 300-4000

Hauppauge, NY 11788 FAX (631) 434-7000

E-mail:

[email protected]

Aventura FBR-8FE1LX-SFP User manual

Brand: Aventura

Model: FBR-8FE1LX-SFP

Category: Network media converters

Type: User manual

Download PDF

report

Aventura FBR-8FE1LX-SFP User manual

Aventura FBR-8FE1LX-SFP User manual

Related papers

Other documents