Vitek VT-PTZ10T LEGACY User manual

VITEK

VT-PTZ10T

Compact HD-TVI/CVBS PTZ Camera

with WDR & 10x Optical Zoom

VT-PT12/CMT

VT-PTZ10T Pedestal

Ceiling Mount

VT-MD/WMT

Mighty Dome /

VT-PTZ10T Wall Mount

VT-MD/PLMT

Mighty Dome /

VT-PTZ12 Pole Mount

Adapter

VT-MD/CNMT

Mighty Dome /

VT-PTZ12 Corner Mount

Adapter

• 1/3” Panasonic CMOS Sensor

• 2.1 MegaPixel HD-TVI / 700TVL CVBS Output

• Built-In 5.1 to 51mm Lens with 10x Optical / 32x Digital Zoom

• True Day/Night function with ICR

• 128 Presets programmed with view direction, zoom, and BLC

• 8 Patterns record and play back user preference of surveillance path up to 120º sec.

• 8 Scans: 8 speed steps from slow to medium panning with smooth Diagonal Scan

• 4 Tours: Each tour consists up to 32 Presets, Patterns, and/or Scans

• 4 Alarm inputs with 1~4 priority / 1 Auxiliary output with programmable NC & NO

• 8 Privacy Zones: Video off or up to 8 masked blocks

• 64 steps of variable speed from 0.4º/sec to 90º/ sec. Max manual speed 190º/sec

with Turbo key pressed, Preset speed is 380º/sec.

• Built-in RS-485 receiver driver, power-line surge lightning protection, Heater/Blower

for use in Extreme Temperatures

• Wide Dynamic Range (WDR) accurately captures clear images even in scenes that

contain both very bright and very dark areas

• IP 67 with optional Mounting bracket

FEATURES

OPTIONAL ACCESSORIES:

1 2

VT-PTZ10T

UNPACKING

Before installing the Dome camera, please make sure that the following items are

included in the box:

1. Mini Speed Dome Camera

2. Instruction Manual

3. Mounting Hardware

If any of these materials are missing, please contact the vendor or VITEK customer help

desk immediately.

2

VT-PTZ10T

DISCLAIMER

• While every effort has been made to ensure that the information contained in this

guide is accurate and complete, no liability can be accepted for any errors or

omissions.

• VITEK reserves the right to change the specifications of the hardware and software

described herein at any time without prior notice.

• No part of this guide may be reproduced, transmitted, transcribed, stored in a

retrieval system, or translated into any language in any form, by any means, without

prior written permission of VITEK.

• VITEK makes no warranties for damages resulting from corrupted or lost data due to

a mistaken operation or malfunction of the Speed Dome Cameras, peripheral

devices, or unapproved/unsupported devices.

3 4

VT-PTZ10T

WARNING AND CAUTION

4

VT-PTZ10T

FCC COMPLIANCE STATEMENT

CE COMPLIANCE STATEMENT

FCC INFORMATION: THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO

COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL DEVICE, PURSUANT TO

PART 15 OF THE FCC RULES. THESE LIMITS ARE DESIGNED TO PROVIDE

REASONABLE PROTECTION AGAINST HARMFUL INTERFERENCE WHEN

THE EQUIPMENT IS OPERATED IN A COMMERCIAL ENVIRONMENT. THIS

EQUIPMENT GENERATES, USES, AND CAN RADIATE RADIO FREQUENCY

ENERGY AND IF NOT INSTALLED AND USED IN ACCORDANCE WITH THE

INSTRUCTION MANUAL, MAY CAUSE HARMFUL INTERFERENCE TO RADIO

COMMUNICATIONS. OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL

AREA IS LIKELY TO CAUSE HARMFUL INTERFERENCE IN WHICH CASE THE

USER WILL BE REQUIRED TO CORRECT THE INTERFERENCE AT HIS OWN

EXPENSE.

CAUTION: CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY

THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER'S

AUTHORITY TO OPERATE THE EQUIPMENT.

THIS CLASS A DIGITAL EQUIPMENT COMPLIES WITH CANADIAN ICES-003.

CET APPAREIL NUMÉRIQUE DE LA CLASSE A EST CONFORME À LA NORME

NMB-003 DU CANADA.

WARNING

THIS IS A CLASS A PRODUCT. IN A DOMESTIC ENVIRONMENT THIS

PRODUCT MAY CAUSE RADIO INTERFERENCE IN WHICH CASE THE USER

MAY BE REQUIRED TO TAKE ADEQUATE MEASURES.

5 6

VT-PTZ10T

IMPORTANT SAFEGUARDS

1. Read these instructions.

2. Heed all warnings.

3. Follow all instructions.

4. Do not use this equipment near water.

5. Clean only with dry cloth.

6. Do not block any ventilation openings. Install in accordance with the manufacturer's

instructions.

7. Do not install near any heat sources such as radiators, heat registers, stoves, or

other equipment (including amplifiers) that produce heat.

8. Do not defeat the safety purpose of the polarized or grounding-type plug. A

polarized plug has two blades with one wider than the other. A grounding type plug

has two blades and a third grounding prong. The wide blade or the third prong is

provided for your safety. If the provided plug does not fit into your outlet, consult an

electrician for replacement of the obsolete outlet.

9. Protect the power cord from being walked on or pinched, particularly at plugs,

convenience receptacles, and the point where they exit from the equipment.

10. Only use attachments/accessories specified by the manufacturer.

11. Unplug this equipment during lightning storms or when unused for long periods of

time.

12. Refer all servicing to qualified service personnel. Servicing is required when the

equipment has been damaged in any way, such as power-supply cord or plug is

damaged, liquid has been spilled or objects have fallen into the equipment, the

equipment has been exposed to rain or moisture, does not operate normally, or has

been dropped.

13. CAUTION - THESE SERVICING INSTRUCTIONS ARE FOR USE BY QUALIFIED

SERVICE PERSONNEL ONLY. TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT PERFORM ANY SERVICING OTHER THAN THAT CONTAINED IN THE

OPERATING INSTRUCTIONS UNLESS YOU ARE QUALIFIED TO DO SO.

Use Certified/Listed Class 2 power supply transformer only.

6

VT-PTZ10T

TABLE OF CONTENTS

ABLE OF CONTENTS

DISCLAIMER ................................................................................................................... 1

I. INTRODUCTION .......................................................................................................... 6

Features .................................................................................................................................................. 6

II. INSTALLATION AND CONFIGURATION ................................................................... 7

2.1 Typical System Configuration ........................................................................................................ 7

2.2 Basic Configuration of Speed Dome Camera System .................................................................. 8

2.3 Connecting the Speed Dome directly into the DVR ...................................................................... 9

2.4 Connecting the Speed Dome into the Controller via J-box ......................................................... 9

2.5 Connecting Both Speed Dome and DVR via J-box ..................................................................... 10

2.6 Setting Video Out ........................................................................................................................... 12

2.7 Principle of Termination ................................................................................................................ 12

2.8 Dome Camera Address (ID) .......................................................................................................... 14

2.9 Setting Protocols ........................................................................................................................... 14

2.9 Connections ................................................................................................................................... 15

2.10 Mounting the Dome Camera ....................................................................................................... 16

2.11 Power on and Boot-up Sequence ............................................................................................... 17

III. PROGRAM & OPERATION ...................................................................................... 18

Dome Camera Selection ...................................................................................................................... 18

3.1 FUNCTIONS .................................................................................................................................... 18

3.1.1 HOME FUNCTION (MENU =>FUNCTIONS => HOME FUNCTION) ................................................................................. 19

3.1.2 PRESET (MENU => FUNCTIONS => PRESET Short Cut: PRST) ................................................................................... 20

3.1.3 SCAN (MENU => FUNCTIONS => SCAN or Shortcut: SCAN) ......................................................................................... 22

3.3 SCREEN .......................................................................................................................................... 27

3.3.1 LANGUAGE (MENU => SCREEN => LANGUAGE) ......................................................................................................... 27

3.3.2 NORTH DIRECTION (MENU => SCREEN => NORTH DIRECTION) .............................................................................. 28

3.4 CAMERA (MENU => CAMERA) ..................................................................................................... 30

3.4.1 FOCUS CONTROL (MENU => CAMERA => FOCUS CONTROL) .................................................................................. 30

3.4.2 WB (white balance) (MENU => CAMERA => WB CONTROL) ......................................................................................... 30

3.4.3 EXPOSURE SETUP (MENU => CAMERA => EXPOSURE SETUP) .............................................................................. 31

3.4.4 BLC/WDR (MENU è CAMERA èBLC/WDR) ................................................................................................................. 31

3.4.5 DEFOG (MENU è CAMERA èDEFOG) ......................................................................................................................... 31



3.4.6 SHARPENSS CONTROL (MENU => CAMERA =>SHAPENESS) ................................................................................... 32

3.4.7 DIGITAL ZOOM (MENU => CAMERA =>DIGITAL ZOOM) .............................................................................................. 32

3.4.8 NIGHT SHOT MENU (MENU => CAMERA =>NIGHT SHOT) .......................................................................................... 32

3.4.9 DIS (MENU => CAMERA =>DIS (Digital Image Stabilization)) ......................................................................................... 32

3.4.10 CAMERA INITIALIZE (MENU => CAMERA =>CAMERA INITIALIZE) ........................................................................... 32

3.5 SETUP (MENU => SETUP)............................................................................................................. 33

3.5.1 FLIP (MENU => SETUP => FLIP) ...................................................................................................................................... 33

3.5.2 SPEED (MENU => SETUP => SPEED) ............................................................................................................................. 33

3.5.3 PRESET FREEZE (MENU => SETUP => PRESET FREEZE) .......................................................................................... 33

3.5.4 PANNING RANGE (MENU => SETUP => PANNING RANGE) ......................................................................................... 34

3.5.5 TILT LIMIT (MENU => SETUP => TILT LIMIT) .................................................................................................................. 34

3.5.6 CALIBRATION (MENU => SETUP => CALIBRATION) ..................................................................................................... 34

3.5.7 RESOLUTION (MENU => SETUP => RESOLUTION) ....................................................................................................... 35

3.5.8 FACTORY DEFAULT (MENU => SETUP => FACTORY DEFAULT) ................................................................................ 35

3.5.9 ERASE DATA (MENU => SETUP => ERASE DATA) ........................................................................................................ 35

3.5.10 SYSTEM INFORMATION (MENU => SETUP => SYSTEM INFORMATION) ................................................................. 35

Appendix A — Troubleshooting ................................................................................. 37

Glossary ........................................................................................................................ 38

7 8

VT-PTZ10T

I. INTRODUCTION

Features

The Speed Dome Camera features a high resolution 1/3” CMOS imager for enhanced

lowlight sensitivity. User friendly, on-screen pull-down menus and short-cuts make it

easy to setup and program functions.

System information aides trouble shooting by displaying the hardware and software

version of the camera’s firmware version, baud rate, and protocol.

• Built-in 10X times Optical Zoom Camera.

True Night Shot function with ICR Day/Night function.

• Digital Image Stabilization function.

• 128 Presets programmed with view direction, zoom, and BLC & WDR.

• 8 Scans: 8 speed steps from slow to medium panning with smooth DiagonalScan.

• 4 Tours: Each tour consists up to 32 Preset, Pattern, or Scans.

Smooth DiagonalScan mode and programmable Individual dwell time camera

functions.

• 4 Alarm inputs with 1~4 priority / 1 Auxiliary outputs programmable NC & NO.

• 64 steps of variable speed from 0.4°/sec to 140°/sec.

Max manual speed 190°/sec with Turbo key pressed, Preset speed is 380°/sec.

• Programmable user preferences of speed (Slow, Medium, and Fast).

• Addressable up to 99 camera IDs (Extendable up to 3999 in special mode).

• Built-in RS-485 receiver driver.

• On-site software upgrade and upload/download of programmed data into the

KBD/Dome.

• Built-in power-line surge protection and lightning protection.

• Optional Tinted Bubble, Indoor & Outdoor pendant housing, Heater & Blower.

Flush Mount Kit

8

VT-PTZ10T

II. INSTALLATION AND CONFIGURATION

2.1 Typical System Configuration

Additional Speed Dome joystick controllers and a variety of external switching devices

such as multiplexers (MUXes) and Digital Video Recorders (DVRs) may be incorporated

to accommodate the needs from a small to a large surveillance/security system.

Figure 1 illustrates sample installation.

Figure 1 - Typical System Configuration

9 10

VT-PTZ10T

STP AWG # 22

VIDEO

BNC MONITOR

AC 24V

POWER

HALF DUPLEX MODE

TRX-

TRX+

TRX-

CONTROLLER

DOME

POWER

AC 24V

HEATER

1 AUX OUTPUT

4 ALARM INPUT

COMM.(TRX+/TRX-)

RS-485

2.2 Basic Configuration of Speed Dome Camera System

Figure 2 - Basic Installation Diagram

10

VT-PTZ10T

2.3 CONNECTING THE SPEED DOME DIRECTLY INTO THE DVR

• Locate the RS485 + & - conductor wire from the Speed Dome Camera.

• Connect the + & - into the TRX+ & TRX- ports of the DVR. Tx+ & Tx- ports can be found

on the rear panel of the DVR.

Figure 3 - Camera into DVR

2.4 CONNECTING THE SPEED DOME INTO THE CONTROLLER VIA J-

BOX

Figure 4 - Camera into Controller

11 12

VT-PTZ10T

2.5 CONNECTING BOTH SPEED DOME AND DVR VIA J-BOX

Figure 5 - Connecting Camera & DVR into Controller

12

VT-PTZ10T

Video

Power AC 24V~

Comm.(RX/TX)

Heater AC 24V~

1 Aux Output

4 Alarm Input

Fan

1

2

3

4

5

6

7

8

9

0

S2

S1

9

8

7

6

5

4

3

2

0

1

Selection Switches

S4 S3S5

Address(ID)

Termination

Protocol

The dome camera must be installed by qualified service personnel. Before installing the

dome camera system, this instruction manual must be read thoroughly and understood

fully. Dome cameras must be set up properly before starting the installation. This

involves properly setting configuration switches. Figure 6 shows the location of these

switches.

Figure 6 - Layout of Switches

13 14

VT-PTZ10T

2.6 SETTING VIDEO OUT

HD

1 3

SD

1 3

TVI OUT

CVBS OUT

SD

HD

1 3

Figure 7 - Setting Video Out

2.7 Principle of Termination

The device that is connected at the end of the communication data line must be

terminated by either the DIP switch setting or an appropriate device such as a

termination jumper to prevent potential control signal errors.

See Figure 8 for termination switch settings and Figure 9 for examples of devices

requiring termination. Note: Total length of the cable for communication should not

exceed 1.2Km or .74 mile.

** Unless communication error, put the position 2, 3 of the S5 in OFF state.

Position 2, 3 should be set as a pair. (Both 2, 3 to ON position or OFF position)

Figure 8 - Setting Dome Camera Termination

S5

D1

D2

D3

D4

Terminated

Not

Used

X

ON

Not terminated

X

OFF

Pull Up/Down **

ON

X

Normal **

OFF

X

14

VT-PTZ10T

Figure 9 - Termination Diagram

SW1:Termination ON

SW!:Termination ON

TERMINATION ON

SW1:Termination ON

DVR Termination ON

S1:Dome1 port Termination ON

SW1:Termination ON SW1:Termination ON

DVR Termination ON

SW1:Termination ONSW1:Termination ON

SW1:Termination ON

S1:Dome1 port Termination ON

S4:DVR port Termination ON

DVR Termination ON

SW1:Termination ON

S1:Dome1 port Termination ON

S3:Dome2 port Termination ON

SW1:Termination ON

15 16

VT-PTZ10T

1

2

3

4

5

6

7

8

9

0

S2

S1

S3

S4

3

2

6

5

4

8

7

9

1

0

on

D1 D4 D5 D8

.. ..

2.8 Dome Camera Address (ID)

Each dome camera must have a unique address (ID). Identical IDs on the same line

may damage the control circuit caused by an electrical short. When installing multiple

dome cameras or a DVR, it is recommended that the dome camera ID’s be identical to

the camera port of the DVR.

Cam Port 1 = Dome ID1, Cam Port 2 = Dome ID 2 … Cam Port 16 = Dome ID 16.

If more than 16 dome cameras are installed using two or more DVRs the following

formula is useful to determine the Dome ID: ID =16x (n-1) +m (where n= number of

DVR, m=Camera Port)

Refer to Figures 10 for setting the dome camera address (ID) and protocol selection.

Figure 10 - Setting Dome Camera Address (ID) and Protocol

2.9 Setting Protocols

A Speed Dome camera is capable of negotiating with multiple protocols if the

communication speed is matched (same baud rate i.e., 9600 bps). See Figure 10 for the

appropriate protocol switch settings.

Note: Consult service personnel if a dome camera is installed with a device other than a

recommended Speed Dome Controller.

Dip S/W

Function

S4

D1

Protocol

D2

D3

D4

S3

D5

Baud Rate

D6

D7

D8

Extended ID

Protocol

D1

D2

D3

D4

AUTO Selection(no parity)

DEFAULT

Off Off Off Off

AUTO selection(even parity)

On

Off

PP

Off

On

Off

EZ

On

Off

S2

Off

On

Off

PD

On

Off

On

Off

VC

Off

On

Off

SN

On

Off

DC

Off

On

Reserved

On

Off

On

PPS

Off

On

Off

On

Reserved

On

Off

On

Reserved

Off

On

VVL

On

Off

On

DDI

Off

On

Reset

On

Baud Rate

D5

D6

D7

2400 bps

Off

4800 bps

Off

ON

9600 bps

Off

ON

Off

19200 bps

Off

ON

38400 bps

ON

Off

VIDEO

D8

NTSC

Off

PAL

On

for setting the dome camera address (ID)

protocol

DOME ID

S2

S1

1

0

1

.

99

9

16

VT-PTZ10T

Figure 11 - Protocol Selection tables

2.9 Connections

• How to Connect RS485

The dome camera has a built-in RS-485 receiver so that it can be controlled

remotely by an external control device such as a joystick controller or a DVR.

RS-485: Connect the TXA (Tx+) and TXB (Tx-) of the RS485 control devices

(KBD, DVR…) to TRX+, TRX- of the dome camera.

RS-485 does not allow for a star connection layout. A splitter is required if a

star connection layout is desired. RS-485 guarantees 1.2 Km of data line

routing. A repeater is recommended to extend over 1.2 Km.

• Connecting Alarms

AL1 to 4 (Alarm In)

Magnetic, PIR or other external sensor devices can be used to signal the

dome camera reacting to an event.

See Chapter 3.2 — Program and Operation for configuring alarm input.

GND (Ground)

NOTE: All the connectors marked GND are common.

Connect the ground of the Alarm input and/or alarm output to the GND

connector.

NO / NC (Normally Opened or Normally Closed dry contact relay output)

The dome camera can activate external devices such as buzzers or lights

using dry contact relays. Connect the device to the NO (NC) (Alarm Out) and

COM (Common) connectors. See Chapter 3 — Program and Operation for

configuring alarm output.

• Connecting the Power

Connect AC 24V 40VA power to the dome camera.

Use certified / Listed Class 2 power supply transformer only.

17 18

VT-PTZ10T

2.10 Mounting the Dome Camera

Once all DIP switches are set properly and all external connections are made, the dome

camera can be mounted.

The Mini PTZ Dome camera is designed to mount on a structural body supporting

loads up to 6.6Lbs / 3 Kg. See Figure 12.

Figure 12 - Example of a flush mounted installation

Installation Hint

Using Four ST4X30 screws, attach flush mount base to sturdy surface

18

VT-PTZ10T

2.11 Power on and Boot-up Sequence

When the power is applied to the dome camera, it will start the boot-up sequence.

When boot-up is done, the following information is displayed on the monitor screen.

On Screen Display in normal control mode

RAM TEST

CHECK NO. : OK!

CHECK AAAA : OK!

CHECK 5555 : OK!

XPRESS DOME Vx.xxx

ID:0001 9600BPS AUTO

CAMERA TYPE xxxx

TILT ORIGIN SET OK

PAN ORIGIN SET OK

INITIAL CAMERA OK

001PRESET W→

EMPTY DATA !

ALARM:1

360.0,090.0 CAM xxxx

Preset No.

Information

Alarm Display

Dome Camera Title

Dome Camera ID

Compass Direction

Pan & Tilt Angle

Preset Title

Or Area Title

19 20

VT-PTZ10T

III. PROGRAM & OPERATION

Dome Camera Selection

Prior to programming or operating a dome camera, please make sure that both the

camera and the joystick controller are communicating. In order for changes to take

effect for a camera, particular camera’s ID must be selected on the controller.

Example: Pressing 1 , 6 and CAM key sequentially will select dome camera 16. The

selected dome camera ID will be displayed on the monitor.

Principle of joystick usage in the programming (editing) mode

Button or Joystick movement in menu

Function

Joystick left or right

Go into the sub-menu items.

Execute the command(exit)

Change value.

Navigate through the menu items.

Joystick

up or down

Navigate through the menu items.

Joystick

down

Finish editing title.

Zoom handle twist

Change value.(Increase / Decrease)

Enter editing title mode.

SHFT + Joystick

PTZ control mode.

ESC

Escape from the menu without change.

Home or Off button

Delete value or name of the field.

3.1 FUNCTIONS

By pressing the MENU button on the keyboard controller, the following On-screen MAIN

MENU will be shown on the monitor screen.

MAIN MENU

FUNCTION

ALARM

SCREEN

CAMERA

SETUP

EXIT

Page is loading ...

Vitek VT-PTZ10T LEGACY User manual

This manual is also suitable for

Vitek VT-PTZ10T LEGACY User manual

in other languages

Related papers

Other documents