Bticino F470/2 is a 2-relay radio actuator that can be used in both traditional and My Home Bticino systems to add home automation functionalities or to create a mixed radio-wire bus system. The device can be controlled by radio controls or by means of the local micro pushbuttons on the device. It can be used to operate blinds, rolling shutters, light points, or similar loads. The two relays can work in an interlocked mode or independently, depending on the configuration.
Bticino F470/2 is a 2-relay radio actuator that can be used in both traditional and My Home Bticino systems to add home automation functionalities or to create a mixed radio-wire bus system. The device can be controlled by radio controls or by means of the local micro pushbuttons on the device. It can be used to operate blinds, rolling shutters, light points, or similar loads. The two relays can work in an interlocked mode or independently, depending on the configuration.
Page is loading ...
Page is loading ...
GB
2-RELAY RADIO ACTUATOR
6
Power supply:
230 V a.c. 50 Hz
Operating temperature:
+5°C ÷ +35°C
Frequency
: 868 MHz
Size: 2 DIN modules
Range: 100 m in free space
(metal and cement walls or metal plates reduce the range)
7
TECHNICAL DATA
This radio device can be used, together with other Bticino radio devices, in
both a traditional system
(to add house-automation
functions) and
a Bticino My Home system
to make full use of the benefi ts of radio technology in a mixed radio-wire bus
system.
If the F470/2 actuator is used in a traditional system it can be controlled directly by radio controls or by means of the local micro
pushbuttons on the device. If instead it is used in a My Home system, as well as being directly controlled by radio controls and
by means of the local micro pushbuttons, it can also be controlled by the system’s wire controls (by means of the transmitting
interface L/N/NT4576N HC/HS4576).
DECLARATION OF CONFORMITY
Item
F470/2
conforms to the essential requirements of directive 1999/5/CE, because it respects the following standards:
ETSI EN 300 220-3 ETSI EN301 489-3 EN60669-2-1
Year of approval of the CE marking according to the directive indicated: 2005
Type of load
Max.
Resistive loads
6 A
Incandescent lamp
2 A
Fluorescent lamps
0.3 A
Rolling shutter motors
500 W
Electronic transformers
0.3 A
Ferromagnetic transformers
cos
f
= 0,5
2 A
AR
T
.F470/2
T.F470/2T
NO
NO
C
L
N
1
2
3
Configurator
housing
LED (luminous indicators)
Micro pushbuttons
Relay contacts
Power supply
230V~ 50Hz
Left yellow LED ON = load active/programming
Right yellow LED ON = load 2 active
Left yellow LED flashing = wrong configuration
CONFIGURATION
8
The F470/2 radio actuator can be used in both a traditional system and a
My Home system. In both cases it must be
programmed.
When used in a traditional system
, the device can only be used to operate blinds, rolling shutters or similar loads. The
working of the two relays is interlocked and no confi guration is necessary apart from, possibly, the mode M confi gurator. In
this mode of use the device can be controlled by radio control devices such as, for example, radio remote control 3527 or
radio control L4572.
Use of item F470/2 in traditional systems to operate blinds, rolling shutters or similar loads.
Type of system
A
PL1
PL2
M
G
Traditional system
None
None
None
None
, 1÷4
None
Possible functions
Confi guration position M
Timed stop for motor-operated devices: the actuator deactivates after the time set:
None = 1 min, 1 = 2 min, 2 = 5 min, 3 = 10 min, 4 = infi nite or until next command
None
, 1÷4
The confi guration operations must be performed with the actuator s
witched OFF.
9
PROGRAMMING
1) Switch on the device.
2) Keep the left micro pushbutton pressed until the left LED lights up (about 4 seconds).
3) Release the key.
4) Within 20 seconds send the signal from the radio control device to be programmed.
Example:
For remote control item 3527 press the key to be associated with the actuator.
5) The left LED fl ashes and then goes out, indicating that programming has taken place.
6) Repeat the sequence of operations from point 2 to point 5 for all the radio control devices to be programmed (max. 16).
10
CANCELLING
This operation cancels all the radio control devices previously programmed in the actuator.
1)
Switch on the device.
2)
Keep the left micro pushbutton pressed for 11 seconds (after 4 seconds the left LED switches ON, after another 7 seconds the left LED switches
OFF).
3)
Release the key.
4)
The left LED fl ashes and then goes out, indicating that all the radio control devices previously programmed in the actuator have been cancelled.
1
2
3
1
2
3
1
2
3
1
2
3
1
2
3
1
2
3
1
2
3
1
2
3
When used in a My Home system
,
the device can be used not only to operate blinds or rolling shutters, but also to control light points. In this
mode of use, the actuator can be controlled by radio control devices such as, for example, radio remote control L4572 or transmitting radio
interface item L/N/NT4576N HC/HS4576. In My Home systems, at least positions A, PL1 and PL2 must be confi gured.
If confi gurators PL1 and PL2 are the same, the actuator is confi gured to operate blinds and rolling shutters and the two relays are
interlocked.
Use of item F470/2 in My Home systems to operate blinds, rolling shutters or similar loads.
Type of system
A
PL1
PL2
M
G
My Home system with
rolling shutters
1÷9
1÷9 (PL1 = PL2)
1÷9 (PL1 = PL2)
None
, 1÷4, PUL
None
, 1÷9
Possible functions
Confi guration position M
Timed stop for motor-operated devices: the actuator deactivates after the time set:
None = 1 min, 1 = 2 min, 2 = 5 min, 3 = 10 min, 4 = infi nite or until next command
None, 1÷4
The actuator ignores the Area and General commands and deactivates after 1 minute
PUL
As an alternative to being used to operate rolling shutters, the actuator can be used to control one or two light points. If position PL2 is confi gured
the two relays are used independently. If, instead, position PL2 is not confi gured then just one relay is used. To set this mode at least A and PL1
must be confi gured.
Type of system
A
PL1
PL2
M
G
All the types of My Home
system with one or two loads
1÷9
1÷9
None,1÷9
None, PUL
None, 1÷9
Possible functions
Confi guration position M
Normal operation
None
The actuator ignores the Area and General commands
PUL
If the confi guration is wrong, once there is power to the actuator, the left LED fl ashes continuously.
-
1
-
2
-
3
-
4
Bticino F470/2 is a 2-relay radio actuator that can be used in both traditional and My Home Bticino systems to add home automation functionalities or to create a mixed radio-wire bus system. The device can be controlled by radio controls or by means of the local micro pushbuttons on the device. It can be used to operate blinds, rolling shutters, light points, or similar loads. The two relays can work in an interlocked mode or independently, depending on the configuration.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
- italiano: Bticino F470/2 Istruzioni per l'uso
Related papers
-
Bticino F470/1 Operating instructions
-
-
-
-
-
-
-
-
-
Other documents
-
Alpha VBL15X47BU User manual
-
Nice F470 User manual
-
Legrand TESTPDF1 Installation guide
-
Nibe F470 Installer Manual
-
Vemer KLIMA LCD RF User manual
-
SEAV LTX 2296 User guide
-
Quick BTR250 User manual
-
Quick BTR1806512 Installation and Use Manual
-
SICK T4000 Multi Safety Switch Operating instructions
-
Elvox 69PH Installer's Manual
