Lifetime 90179 Owner's manual

MODEL N° 90179

OWNER’S MANUAL

3

SAFE HANDLING OF THE GLASS BACKBOARD

BEFORE & DURING ASSEMBLY

5IPSPVHIMZJOTQFDUUIF#BDLCPBSECFGPSFCFHJOOJOHBTTFNCMZ%POPUVTFUIF#BDLCPBSEJGUIFSFBSFBOZDIJQTDSBDLT

PSPUIFSEFGFDUTJOUIFCPBSE$BMMPVS$VTUPNFS4FSWJDF%FQBSUNFOUJGBOZQSPCMFNTBSFGPVOE

6TFFYUSFNFDBVUJPOXIFOIBOEMJOHPSXPSLJOHBSPVOEUIF#BDLCPBSE

,FFQUPPMTIBSEXBSFBOEPUIFSTIBSQBOEIFBWZPCKFDUTBXBZGSPNUIF#BDLCPBSE

/FWFSSFTUUIF#BDLCPBSEEJSFDUMZPOBIBSETVSGBDFTVDIBTDPODSFUFPSQBWFNFOU"MXBZTQMBDFDBSECPBSEPSPUIFS

DVTIJPOJOHNBUFSJBMCFUXFFOUIF#BDLCPBSEBOEUIFHSPVOEPSPUIFSIBSETVSGBDFT

"MXBZTMBZUIF#BDLCPBSEnBU/FWFSQMBDFJUJOBQPTJUJPOXIFSFJUNJHIUUJQPWFSBOECSFBL

(MBTTJTWFSZIFBWZ"MXBZTVTFBUMFBTUUXPBEVMUTXIFOQJDLJOHVQPSNPWJOHUIF#BDLCPBSE

GENERAL HANDLING & CARE

*OTQFDUUIF#BDLCPBSECFGPSFFBDIVTF%POPUVTFUIF#BDLCPBSEJGUIFSFBSFBOZDIJQTDSBDLTPSPUIFSEFGFDUTJOUIF

CPBSE*GBOZTJHOTPGEBNBHFBSFGPVOEGPMMPXUIFJOTUSVDUJPOTGPSi)BOEMJOH#SPLFO(MBTTwCFMPX

6TFFYUSFNFDBVUJPOXIFOIBOEMJOHPSXPSLJOHBSPVOEUIF#BDLCPBSE

5IF#BDLCPBSEXBTEFTJHOFEGPSVTFXJUIB#BTLFUCBMM%POPUVTFPUIFSUZQFTPGCBMMTPSPUIFSPCKFDUTXJUIUIFTZTUFN

%POPUVTFUIJTTZTUFNGPSBOZQVSQPTFPUIFSUIBOJUTEFTJHOFEQVSQPTF

HANDLING BROKEN GLASS

At the ﬁ rst sign of breakage:

,FFQFWFSZPOFFTQFDJBMMZDIJMESFOBXBZGSPNUIFJNNFEJBUFBSFBPGUIF#BDLCPBSE

1VUPOFZFQSPUFDUJPOBOEXFBSUIJDLVUJMJUZHMPWFTBOEMPOHTMFFWFT4NBMMQJFDFTPGUFNQFSFEHMBTTNBZQPQPVUPGUIF

#BDLCPBSE

-PXFSUIF#BDLCPBSEUPJUTMPXFTUIFJHIUBOEDPNQMFUFMZDPWFSUIF#BDLCPBSEXJUIBUBSQ

%POPUSFNPWFUIF#BDLCPBSEGSPNUIFTZTUFNXJUIPVUmSTUMPXFSJOHUIFTZTUFNUPJUTMPXFTUTFUUJOH$BSFGVMMZSFBEBOE

GPMMPXUIFi3FNPWJOH#BDLCPBSEGSPN4ZTUFNwJOTUSVDUJPOTCFMPX

REMOVING BACKBOARD FROM SYSTEM

See Section 7 of this manual for instructions on how to safely remove the backboard from the system.

*Six adults required to

complete assembly*

Only adults should set up the product. Do not allow children

in the setup area until assembly is complete.

4

BEFORE BEGINNING ASSEMBLY

" ,FFQUIFIBSEXBSFCBHTBOEUIFJSDPOUFOUTTFQBSBUF*GBOZQBSUTBSFNJTTJOHDBMMPVS$VTUPNFS

4FSWJDF%FQBSUNFOU

# 5FTUmUBMM#PMUTCZJOTFSUJOHUIFNJOUPUIFJSSFTQFDUJWFIPMFT*GOFDFTTBSZDBSFGVMMZTDSBQFBXBZBOZ

FYDFTTQPXEFSDPBUJOHCVJMEVQGSPNJOTJEFUIFIPMFT%POPUTDSBQFBXBZBMMPGUIFQPXEFSDPBUJOH

#BSFNFUBMNBZSVTU:PVNBZOFFEUPQPVOETPNF#PMUTJOUPQMBDFXJUIBIBNNFSPSNBMMFU

TOOLS AND PARTS REQUIRED FOR THIS ASSEMBLY

*This system comes in 3 boxes.

Do not attempt assembly until all 3 boxes have arrived.*



3/4”



Cement

Rubber Mallet



1/2”



1/4” Allen Wrench



9/16”



3/8” Allen Wrench



Shovel Carpenter’s Level

 

ZBSEPS

MCCBHY

Tape Measure



Ladder



Adjustable Wrench

PQUJPOBM

Flathead Screwdriver

15/16”



This area is located at the top, left-hand

corner of the page and indicates which tools

and hardware are needed to complete the

assembly steps on a page.

This area is located at the top, right-hand

corner of the page and shows an image of the

product with shaded parts indicating which

section is being assembled.

SEC

#

Note:

!

Refer to the following areas throughout the instructions

to assist in the assembly process:

This area is usually located in the bottom,

left-hand corner of a step and indicates that

special attention is needed to perform a

particular part of a step.

These areas are usually located in the bottom,

right-hand corner of a step and indicate that

damage to the product or serious injury may

occur if the caution or warning is not heeded.

Throughout the Parts & Hardware List, Part

& Hardware Identiﬁ ers, and instructions

are three-letter IDs. These IDs are below

the images of the parts and hardware to

help you locate and identify the parts and

hardware during assembly. These IDs are not

necessarily on the parts themselves.

WARNING

ASSEMBLY GUIDES

TOOLS AND HARDWARE REQUIRED FOR THIS PAGE

CAUTION

ADZY

wYw1BO)FBE4DSFX

This area is located at the top, left-hand

corner of the page and indicates which tools

and hardware are needed to complete the

assembly steps on a page.

This area is located at the top, right-hand

corner of the page and shows an image of the

product with shaded parts indicating which

section is being assembled.

SEC

#

Note:

!

Refer to the following areas throughout the instructions

to assist in the assembly process:

This area is usually located in the bottom,

left-hand corner of a step and indicates that

special attention is needed to perform a

particular part of a step.

These areas are usually located in the bottom,

right-hand corner of a step and indicate that

damage to the product or serious injury may

occur if the caution or warning is not heeded.

Throughout the Parts & Hardware List, Part

& Hardware Identiﬁ ers, and instructions

are three-letter IDs. These IDs are below

the images of the parts and hardware to

help you locate and identify the parts and

hardware during assembly. These IDs are not

necessarily on the parts themselves.

WARNING

ASSEMBLY GUIDES

TOOLS AND HARDWARE REQUIRED FOR THIS PAGE

CAUTION

ADZY

wYw1BO)FBE4DSFX

6

HARDWARE LIST

PARTS LIST

ID Item Description Qty

CZA Parts Box 1

"-( Pole 1

",% 6QQFS&YUFOTJPO"SN 2

",& -PXFS&YUFOTJPO"SN"TTFNCMZ 1

"+3 (BT4QSJOH 2

",( (BT4QSJOH$PWFS 2

"-4 -JGUFS"SN 2

"&; w3FCBS 4

"&* +#PMU 4

",5 +#PMU5FNQMBUF 1

$9: -FGU$BN1MBUF 1

$9; 3JHIU$BN1MBUF 1

".5 8BSOJOH4UJDLFS"QQMJFEUP1PMF 1

ID Item Description Qty

CZB Parts Box 2

"+* #BDLCPBSE 1

CZC Parts Box 3

"-9 3JN 1

",; /FU 1

",* Lift Handle 1

"." 3JN$PWFS1MBUF 1

$:" )BOEMF#SBDLFU 2

".0 5SJHHFS1JO 1

",9 )BOEMF-PDL#SBDLFU 1

"-$ 1BE-PDLXJUI,FZOPUQJDUVSFE 1

",1 )FJHIU4UJDLFS 1

ID Item Description Qty

CZD Setup Hardware

"&0 wYw)FY#PMU 1

$:7 w)FY/VU$PVQMFS 1

"&3 w)FY/VU 8

CZE Handle to Pole Assembly Hardware

$:- wYw(SBEF#PMU 1

$:% wYw(SBEF#PMU 3

%%9 wYw(SBEF#PMU 1

$:$ w-BSHF1PMZ4QBDFS 2

$:& wYw4QBDFS 4

$:2 wYw4QBDFS 1

%': wYw4QBDFS 2

$:' w(SBEF/ZMPDL/VU 3

$:/ w/ZMPDL/VU 1

$:( w/ZMPDL/VU 1

"&( w1MBTUJD8BTIFS 2

"&) w1MBTUJD8BTIFS 2

"+; %BSL-JUIJVN(SFBTFOPUQJDUVSFE 1

",) 4JMJDPOF(SFBTF8IJUFOPUQJDUVSFE 1

CZF Extension Arms to Pole Assembly Hardware

$:* wYw(SBEF#PMU 2

$:+ wYw(SBEF#PMU 1

$:, wYw(SBEF#PMU 4

$:) wYw(SBEF#PMU 1

$:0 wYw4QBDFS 1

$:2 wYw4QBDFS 2

$:1 wYw3VCCFS4QBDFS 2

"&( w1MBTUJD8BTIFS 4

"&) w1MBTUJD8BTIFS 4

$:. w8BTIFS 4

$:' w(SBEF/ZMPDL/VU 

$:( w(SBEF/ZMPDL/VU 3

ID Item Description Qty

BCR Backboard to Pole Assembly Hardware

$:+ wYw(SBEF#PMU 1

$:5 wYw(SBEF#PMU 2

"&) w1MBTUJD8BTIFS 2

"&( w1MBTUJD8BTIFS 6

$:( w(SBEF/ZMPDL/VU 1

$:' w(SBEF/ZMPDL/VU 2

CZG Pole to J-Bolt Template Assembly Hardware

"%- w/ZMPDL/VU 4

".4 w/ZMPO$BQ 4

#*1 w6448BTIFS 8

$6" w-PDL8BTIFS 4

BCS Rim to Backboard Assembly Hardware

"#: wYw)FY#PMU 4

"%6 .Y1BOIFBE4DSFX 2

""' w'MBU8BTIFS 8

""" w/ZMPDL/VU 4

7

Parts shown at 10% of Actual Size

PARTS IDENTIFIER

AKZY

/FU

AEZY

w3FCBS

AKEY

-PXFS&YUFOTJPO"SN"TTFNCMZ

AKDY

6QQFS&YUFOTJPO"SN

ALSY

-JGUFS"SN

AJRY

(BT4QSJOH

AKGY

(BT4QSJOH$PWFS

ALXY

3JN"TTFNCMZ

AMAY

3JN$PWFS1MBUF

AKIY

Lift Handle

AKTY

+#PMU5FNQMBUF

AEIY

+#PMU

AKPY

)FJHIU4UJDLFS

8

Part shown at 25% of Actual Size

Part shown at Actual Size

CXZY

3JHIU$BN1MBUF

CXYY

-FGU$BN1MBUF

CYAY

)BOEMF#SBDLFU

ALGY

Pole

AJIY

#BDLCPBSE

AKXY

)BOEMF-PDL#SBDLFU

AMOY

5SJHHFS1JO

Parts shown at 5% of Actual Size

PARTS IDENTIFIER

9

HARDWARE IDENTIFIER

SETUP HARDWARE [CZD]

Hardware shown at Actual Size

HANDLE TO POLE ASSEMBLY HARDWARE [CZE]

Hardware shown at Actual Size

CYVY

w)FY/VU$PVQMFS

AERY

w)FY/VU

AEOY

wYw)FY#PMU

/PUBDUVBMMFOHUI

8 5/8”

CYCY

w-BSHF1PMZ4QBDFS

CYDY

wYw(SBEF#PMU

CYLY

wYw(SBEF#PMU

CYEY

wYw4QBDFS

CYNY

w/ZMPDL/VU

CYFY

w(SBEF/ZMPDL/VU

AEGY

w1MBTUJD8BTIFS

CYQY

wYw4QBDFS

DFYY

wYw4QBDFS

/PUBDUVBMMFOHUI

8 5/8”

DDXY

wYw(SBEF#PMU

CYGY

w(SBEF/ZMPDL/VU

AEHY

w1MBTUJD8BTIFS

10

HARDWARE IDENTIFIER

EXTENSION ARMS TO POLE ASSEMBLY HARDWARE [CZF]

Hardware shown at Actual Size

/PUBDUVBMMFOHUI

11 1/4”

CYGY

w(SBEF/ZMPDL/VU

CYPY

wYw3VCCFS4QBDFS

CYIY

wYw(SBEF#PMU

CYFY

w(SBEF

/ZMPDL/VU

CYMY

wYw8BTIFS

CYKY

wYw(SBEF#PMU

AEHY

w1MBTUJD8BTIFS

CYQY

wYw4QBDFS

CYOY

wYw4QBDFS

AEGY

w1MBTUJD8BTIFS

/PUBDUVBMMFOHUI

8”

CYHY

wYw(SBEF#PMU

CYJY

wYw(SBEF#PMU

8 1/4”

/PUBDUVBMMFOHUI

11

HARDWARE IDENTIFIER

BACKBOARD TO POLE ASSEMBLY HARDWARE [BCR]

Hardware shown at Actual Size

CYTY

wYw(SBEF#PMU

CYFY

w(SBEF/ZMPDL/VU

AEGY

w1MBTUJD8BTIFS

CYJY

wYw(SBEF#PMU

AEHY

w1MBTUJD8BTIFS

CYGY

w(SBEF/ZMPDL/VU

AAAY

w/ZMPDL/VU

ABYY

wYw)FY#PMU

AAFY

w'MBU8BTIFS

ADUY

.YNN

1BOIFBE4DSFX

RIM TO BACKBOARD ASSEMBLY HARDWARE [BCS]

Hardware shown at Actual Size

/PUBDUVBMMFOHUI

8 1/4”

ADLY

w/ZMPDL/VU

AMSY

w/ZMPO$BQ

POLE TO J-BOLT ASSEMBLY HARDWARE [CZG]

Hardware shown at Actual Size

CUAY

w-PDL8BTIFS

BIPY

w'MBU8BTIFS

12

SETUP

HARDWARE REQUIRED

PARTS REQUIRED

TOOLS USED (NOT INCLUDED)

SEC

1

Parts shown at 10% of Actual Size

CYVY

w)FY/VU$PVQMFS

AERY

w)FY/VU

AEOY

wYw)FY#PMU

AEZY

w3FCBS

AKTY

+#PMU5FNQMBUF

AEIY

+#PMU

Carpenter’s Level Shovel

ZBSEPS

MCCBHY

Cement

Tape Measure

SETUP HARDWARE [CZD]

Hardware shown at Actual Size

15/16" Wrench

Y

TOOLS AND HARDWARE REQUIRED FOR THIS PAGE

13

SEC

1

SEC

1.1

SEC

1.2

%JHBIPMFwEFFQBOEwTRVBSF5IFFEHFPG

UIFIPMFTIPVMECFnVTIXJUIUIFFEHFPGUIFQMBZJOH

DPVSU *G ZPV MJWF JO BO BSFB XIFSF GSPTU IFBWFT

NBZ QPTFB QSPCMFNDPOTVMU ZPVS MPDBM CVJMEJOH

JOTQFDUPSUPEFUFSNJOFUIFBQQSPQSJBUFIPMFEFQUI

#FMMPVUUIFCPUUPNPGUIFIPMFBTJMMVTUSBUFE8F

SFDPNNFOECVJMEJOHBGPSNUPLFFQUIFUPQPGUIF

DPODSFUFTUSBJHIUBOETRVBSF1MBDFUIFGPSNTPJU

JTMFWFMXJUIUIFQMBZJOHTVSGBDF

5ISFBEB5/8” Hex Nut (AER) BMM UIF XBZ POUP FBDI

J-Bolt (AEI)4MJEFUIFUISFBEFEFOETPGUIF+#PMUT

UISPVHIUIFDPSOFSIPMFTJOUIFJ-Bolt Template (AKT)

BOETFDVSFUIFNDPNQMFUFMZXJUI5/8” Hex Nuts (AER).

*OTFSUUIF5/8” x 2” Hex Bolt (AEO)UISPVHIUIFDFOUFS

IPMF JO UIF +#PMU 5FNQMBUF BOE UJHIUFO UIF Nut

Coupler (CYV)POUPUIF#PMUBTGBSBTJUXJMMHP

Note: There must be a 3-foot area behind the pole

to allow the user to adjust the Rim height.

!

AEOY

AERY

CYVY

AKT

w

w

w

Note: Make sure the curved ends of the J-Bolts

are in a rectangular pattern as shown.

!

OPUBDUVBMTJ[F

#FGPSFEJHHJOHDBMMUPMPDBUFBOZCVSJFEVUJMJUZMJOFT

CAUTION

CYV

AEI

AER

AEO

AEI

AER

15/16”Y

TOOLS AND HARDWARE REQUIRED FOR THIS PAGE

14

SEC

$FOUFSUIFJ-Bolt Template (AKT)PWFSUIFIPMFThe front

of the Template is the side with the Nut Coupler (CYV) and

should be toward the playing surface.

*OTFSUUIFJ-Bolts (AEI)JOUPUIFDPODSFUFBOEBHJUBUFUIF

5FNQMBUFBTTFNCMZUPFMJNJOBUFBOZBJSCVCCMFT

1VTIUIF+#PMUTJOUPUIFDFNFOUVOUJMUIF5FNQMBUF

JTSFTUJOHnBUBHBJOTUUIFDFNFOU'PSNUIFDFNFOU

JOUPBEPXOXBSETMPQFUPXBSEUIFQMBZJOHTVSGBDF

to allow water runoff. The lower four 5/8” Hex Nuts (AER)

and the Nut Coupler will be in the concrete permanently.

$MFBOPGGBOZDPODSFUFPOUIF+#PMU5FNQMBUFPSUIF

FYQPTFEQPSUJPOPGUIF+#PMUT6TJOHBDBSQFOUFST

MFWFMNBLFTVSFUIF5FNQMBUFJTTRVBSFUPUIFQMBZJOH

TVSGBDF1MBUFTIPVMECFMFWFMBOEBCPVUwBCPWF

UIFQMBZJOHTVSGBDFGPSXBUFSUPESBJOPGGPGUIFTUFFM

1

*GZPVBSFVTJOHDPODSFUFNJYNJYUIFDPODSFUF

BDDPSEJOHUPUIFJOTUSVDUJPOTPOUIFCBHTPlease

note that a thicker mix of concrete will dry stronger.

1PVSUIFDPODSFUFJOUPUIFIPMFTUPQQJOHBCPVU

JODIFTGSPNUIFUPQPGUIFIPMF

1VTIUIFGPVSQJFDFTPG36” Rebar (AEZ)mSNMZUPUIF

CPUUPNPGUIFIPMF5IF3FCBSTIPVMECFBSSBOHFE

JOBTRVBSFBCPVUJODIFTXJEFJOUIFDFOUFSPG

UIFIPMFTPFBDIQJFDFXJMMCFOFYUUPUIF+#PMUT

XIFOUIFZBSFQMBDFEJOUIFDFNFOU

'JOJTImMMJOHUIFIPMFUPUIFUPQXJUIDPODSFUF5IF

UPQPGUIFDPODSFUFTIPVMESFBDIBCPVUwBCPWF

UIFQMBZJOHTVSGBDFBOETMPQFEPXOUPXBSEUIF

QMBZJOHTVSGBDFUPBMMPXXBUFSSVOPGG

SEC

1.3

SEC

1.4

(Not to scale)

AKT

18”

AEI

CYV

AER

Playing surface

Note: You are now ﬁnished with the initial assembly steps. DO

NOT PROCEED WITH THE ASSEMBLY until the concrete has fully

cured. Curing will take a minimum of 72 hours (3 days). In

humid climates or wet weather, allow additional time for the

concrete to cure. Never use the system without ﬁrst following

the cementing instructions.

!

AEZ

MC#BHY

NO HARDWARE REQUIRED FOR THIS PAGE

15

HANDLE TO POLE ASSEMBLY

HARDWARE REQUIRED

SEC

2

/PUBDUVBMMFOHUI

8 5/8”

CYCY

w-BSHF1PMZ4QBDFS

CYDY

wYw(SBEF#PMU

CYLY

wYw(SBEF#PMU

CYEY

wYw4QBDFS

CYNY

w/ZMPDL/VU

CYFY

w(SBEF/ZMPDL/VU

AEGY

w1MBTUJD8BTIFS

CYQY

wYw4QBDFS

DFYY

wYw4QBDFS

HANDLE TO POLE ASSEMBLY HARDWARE [CZE]

Hardware shown at Actual Size

/PUBDUVBMMFOHUI

8 5/8”

DDXY

wYw(SBEF#PMU

CYGY

w(SBEF/ZMPDL/VU

AEHY

w1MBTUJD8BTIFS

16

TOOLS USED (NOT INCLUDED)

1/2" Wrench

Y

Parts shown at 25% of Actual Size

Parts shown at 10% of Actual Size

Part shown at Actual Size

1/4" Allen Wrench

Y

CYAY

)BOEMF#SBDLFU

AKXY

)BOEMF-PDL#SBDLFU

AMOY

5SJHHFS1JO

HANDLE TO POLE ASSEMBLY

PARTS REQUIRED

SEC

2

Part shown at 5% of Actual Size

ALGY

Pole

AKIY

Lift Handle

AJRY

(BT4QSJOH

AKGY

(BT4QSJOH$PWFS

ALSY

-JGUFS"SN

3/4" Wrench

Y

3/8" Allen Wrench

Y

Rubber Mallet

15/16" Wrench

Y

TOOLS AND HARDWARE REQUIRED FOR THIS PAGE

17

SEC

!

2

"UUBDIUIFHandle Brackets (CYA)UPUIFPole (ALG)XJUIUIFIBSEXBSFTIPXO

SEC

2.1

CYEY

CYF

CYD

CYA

CYE

OPUBDUVBMTJ[F

CYFY

3/4"

3/8"

CYDY

8 5/8”

OPUBDUVBMMFOHUI

ALG

Note: DO NOT overtighten the hardware. The Handle Brackets must move freely

around the Bolt. You should be able to rotate the Spacers with your ﬁngers.

!

Note: Coat the 1/2” x 8 5/8” Bolt (CYD) lightly with Dark

Lithium Grease (AJZ) before performing this step.

!

Note: Make sure each Handle Bracket (CYA) is oriented

so the side of the Bracket with the holes is closest to the

ground.

TOOLS AND HARDWARE REQUIRED FOR THIS PAGE

18

SEC

"UUBDIUIFHandle Assembly (AKI)UPUIF)BOEMF#SBDLFUTVTJOHUIFIBSEXBSFTIPXOJOUIFMPDBUJPOJOEJDBUFE

.BLFTVSFUIF1/2” x 1.44” Spacers (CYE)BSFJOTUBMMFEJOUIFHBQCFUXFFOUIF)BOEMF#SBDLFUBOEUIF)BOEMF

"TTFNCMZ

SEC

2.2

CYF

3/4"

2

3/8"

CYE

CYD

CYEY

OPUBDUVBMTJ[F

CYFY

CYDY

8 5/8”

OPUBDUVBMMFOHUI

AKI

Note: DO NOT overtighten the hardware. Make sure the Handle

Assembly is oriented as shown.

!

Note: Coat the 1/2” x 8 5/8” Bolt (CYD) lightly with Dark

Lithium Grease (AJZ) before performing this step.

TOOLS AND HARDWARE REQUIRED FOR THIS PAGE

19

SEC

!

2

4FDVSFUIF)BOEMF"TTFNCMZUPUIF)BOEMF#SBDLFUTVTJOHUIFIBSEXBSFTIPXOJOUIFTFUPGIPMFTBUUIFFOEPG

UIF)BOEMF#SBDLFUT.BLFTVSFUIF1/2” Plastic Washers (AEG)BSFQMBDFECFUXFFOUIF)BOEMF#SBDLFUTBOEUIF

)BOEMF"TTFNCMZ

SEC

2.3

CYF

AEG

CYD

AEGY

CYFY

CYDY

8 5/8”

OPUBDUVBMMFOHUI

3/4"

3/8"

Note: DO NOT overtighten the hardware.

3FNPWFBMMQBDLBHJOHGSPNUIFGas Springs (AJR)4MJEFUIFGas Spring Cover (AKG)POUPUIF(BT4QSJOHBTJMMVTUSBUFE

MJOJOHVQUIFIPMFTJOUIF(BT4QSJOH$PWFSXJUIUIPTFJOUIFOBSSPXFOEPGUIF(BT4QSJOHRepeat this step for the

remaining Gas Spring and Gas Spring Cover.

SEC

2.4

1

2

Note: The Gas Spring Cover will rest loosely on the Gas Spring.

It will be secured to the Gas Spring later in the assembly.

!

AKG

AJR

Note: To simplify the upcoming steps, it may be helpful to fully extend the Gas Springs. To do so, carefully tap the small

release pin at the larger end of the Gas Spring with a Bolt. Continue tapping repeatedly until the Gas Spring is fully extended.

!

Note: Coat the 1/2” x 8 5/8” Bolt (CYD) lightly with Dark

Lithium Grease (AJZ) before performing this step.

TOOLS AND HARDWARE REQUIRED FOR THIS PAGE

20

SEC

!

-JOFVQUIFIPMFTJOUIFGas Spring Cover (AKG) and Gas Spring (AJR)XJUIUIPTFPOUIFQPMFCSBDLFUT4FDVSFUIF

(BT4QSJOHTBOE(BT4QSJOH$PWFSTUPUIF1PMFVTJOHUIFIBSEXBSFTIPXO

SEC

2.5

2

CYL

CYN

CYLY

CYNY

Pole Brackets

Line up the holes

Note: Do NOT overtighten the hardware. The Gas Springs need

to rotate freely on the pole brackets.

1/2"

1/4"

5”

OPUBDUVBMMFOHUI

TOOLS AND HARDWARE REQUIRED FOR THIS PAGE

21

SEC

4MJEFUIFTrigger Pin (AMO)UISPVHIUIFVQQFSTFUPGIPMFTJOUIFGas Springs (AJR).

SEC

2.6

2

AJR

AMO

AJR

1

2

NO TOOLS OR HARDWARE REQUIRED FOR THIS PAGE

Page is loading ...

Lifetime 90179 Owner's manual

Lifetime 90179 Owner's manual

Related papers

Other documents