Sub-Zero 700TR is a tall refrigerator unit with upper cabinet refrigerator and refrigerator storage drawers. It has a 15.5 cu ft storage capacity, dual refrigeration system, and electronic digital controls. The unit is designed for "point-of-use" refrigeration and can be integrated into your cabinetry for a seamless look. The adjustable shelves, drawers, and door compartments allow for flexible storage options. The unit also features an audible door alarm to alert you if a door or drawer is left open.
Sub-Zero 700TR is a tall refrigerator unit with upper cabinet refrigerator and refrigerator storage drawers. It has a 15.5 cu ft storage capacity, dual refrigeration system, and electronic digital controls. The unit is designed for "point-of-use" refrigeration and can be integrated into your cabinetry for a seamless look. The adjustable shelves, drawers, and door compartments allow for flexible storage options. The unit also features an audible door alarm to alert you if a door or drawer is left open.
Removable
crisper cover
Adjustable glass
shelf and deli drawer
Adjustable spill-proof
glass shelves
Electronic digital
control panel
Adjustable dairy
compartment
Seamless
molding
Egg container
Adjustable door
shelves
Lower refrigerator
storage drawer
Upper refrigerator
storage drawer
Front venting with
removable kickplate
Magnetic door /
drawer gaskets
Location of serial
number
Stationary shelf
Planning Information
Integrated Model 700TR
All Refrigerator
1
Dimensions in parentheses are in
millimeters unless otherwise specified.
11/06
The Sub-Zero Model 700TR integrated
design accepts custom wood or stainless
steel door and drawer panels. Stainless
steel panels and handles are available as
sales accessories in three finishes—
classic, platinum and carbon.
Who says bigger is better? In this instance a 27"
(686) wide by 80" (2032) high refrigerator is perfect.
At 15.5 cu ft (439 L) of storage, you have plenty of
space for most households and when coupled with a
Model 700TF or 700TFI you have a 54" (1372) wide
refrigerator/ freezer combination.
With this model, you can adjust the door cabinet
temperature independent of the two drawer environ-
ment. The range for both compartments is 34˚F (1˚C)
to 45˚F (7˚C).
The door swing must be specified when ordering this
unit.
With the installation of a harness kit, these appliances are Star-K
compliant to meet strict religious regulations in conjunction with
specific instructions found on star-k.org. You may purchase this
harness kit through your Sub-Zero dealer. To obtain local dealer
information, visit the Locator section of our website, subzero.com.
Model 700TR
TOP OF
ROUGH
OPENING
789/16"*
(1995)
341/2"*
(876)
14"(356)
13/16"
(21)
93/4"
(248)
4"
(102)
80"*
(2032)
27"
(686)
24"
(610)
*
1/2"(13) +
_ADJUSTMENT IN LEVELING LEGS
FRONT VIEW SIDE VIEW
(UNIT DIMENSION) (UNIT DIMENSION)
3/8"
(10)
131/4"
(337)
1/2"
(13)
101/4"
(260)
203/8"
(518)
DOOR
MOUNTING
DETAIL
DRAWER
MOUNTING DETAIL
105˚
90˚
90˚ DOOR OPENING
DOOR/DRAWER
CLOSED
MAXIMUM DOOR OPENING
*DOOR/DRAWER PANEL THICKNESS NOT INCLUDED – DIMENSION WILL VARY WITH INSTALLATION
DOOR/DRAWER
CLOSED
191/2"*
(495)251/2"*
(648)
24"
(610)
257/8"(657)
45/8"*(117)
TOP VIEW
Planning Information
Integrated Model 700TR
2
Dimensions may vary by ±1/8"(3).
Dimensions in parentheses are in
millimeters unless otherwise specified.
OVERALL DIMENSIONS
FEATURES
Tall refrigerator unit with upper cabinet
refrigerator and refrigerator storage drawers
Integrated design for "point-of-use" refriger-
ation
Dual refrigeration system with two distinct
temperature zones ensures the freshest food
and energy efficiency
Electronic digital controls are up front and
easy to use
Flat to the ceiling bright lighting in cabinet
and drawers
Door alarm will let you know with an audible
beeping if a door or drawer is left open
Adjustable,spill-proof glass shelves
Refrigerator deli drawer for storage of
smaller items
Aremovable crisper cover with a clear-view
window can be used in either storage
drawer
Each storage drawer has a removable divider
The exclusive dual-action hinge has a built-in
90˚ door stop
Meets strict Department of Energy require-
ments
UL approved for US and Canada
Two, five and twelve year residential
warranty – exclusions apply; warranty
information can be found on our website,
subzero.com
Planning Information
Integrated Model 700TR
Dimensions in parentheses are in
millimeters unless otherwise specified. 3
MODEL
Tall Refrigerator Unit 700TR
PANEL OPTIONS
Integrated (custom panels)
Classic Stainless Steel Finish /S
Platinum Stainless Steel Finish /P
Carbon Stainless Steel Finish /B
Stainless steel door and drawer front
panels are ordered and shipped as sales
accessories and include tubular handles.
ACCESSORIES
Drawer front panels with tubular
handles in classic,platinum and
carbon stainless steel
Tubular handles in classic,
platinum and carbon stainless
steel and polished chrome
Shelf and crisper assembly
Dozen egg container with lid
Drawer crisper cover with lid
Dual installation heater kit
Accessories are available through your
Sub-Zero dealer. To obtain local dealer
information, visit the Locator section of
our website, subzero.com.
SPECIFICATIONS
Model 700TR Upper Cabinet Refrigerator
with Refrigerator Drawers
Overall Width 27" (686)
Overall Height 80" (2032)
Overall Depth 24" (610)
Refrigerator Capacity 15.5 cu ft (439 L)
Minimum Height (levelers in) 79 1/2"(2019)
Door Clearance 25 1/2"(648)
Drawer Clearance 19 1/2"(495)
Electrical Requirements 115 V AC, 60 Hz, 15 amp circuit
Annual Energy Usage 425 kWh / $ 39
(based on 9.06 cents per kilowatt hour)
Shipping Weight 360 lbs (163 kg)
Special Note Door and drawer panels and handles are
available in three stainless steel finishes
Specifications are subject to change without notice.
ANTI-TIP
BRACKET*
*PLACEMENT OF THE
ANTI-TIP BRACKET
SHOULD BE 24" (610)
FROM THE FRONT OF THE
UNIT WITHOUT PANELS
TO THE BACK OF THE
ANTI-TIP BRACKET.
25"
(635)
27"
(686)
25"
(635)
11/2"
(38)
131/2"
(343)
TOP VIEW
SIDE VIEW FRONT VIEW
ANTI-TIP
BRACKET
80"
(2032)
41/2"
(114)
21/2"(64)
151/2"(394)
1/4"
(6)
13" (330)
ANTI-TIP
BRACKET
LOCATE ELECTRICAL WITHIN
SHADED AREA – ORIENT GROUND
PRONG TORIGHT AS SHOWN
NOTE: ANTI-TIP BRACKET MUST BE INSTALLED TO
PREVENT UNIT FROM TIPPING FORWARD
Planning Information
Integrated Model 700TR
Dimensions in parentheses are in
millimeters unless otherwise specified. 4
INSTALLATION SPECIFICATIONS
DIMENSIONS
Finished Rough Opening Width 27" (686)
Finished Rough Opening Height 80" (2032)
Finished Rough Opening Depth 25" (635)*
Location of Electrical Within shaded area
* The depth of the Model 700TR is 24" (610) from the front of the unit to its back. Your design
may necessitate moving the unit back, or cabinets forward to achieve a flush fit. This will require
aminimum rough opening depth of 25" (635).
See Installation Instructions shipped with unit for detailed specifications.
Planning Information
Integrated Model 700TR
Dimensions in parentheses are in
millimeters unless otherwise specified. 5
INSTALLATION NOTES
Refer to the illustrations and specifications
for overall dimensions, finished rough opening
dimensions and installation specifics.
IMPORTANT NOTE: The depth of Model 700TR
is 24" (610) from the front of the unit to its
back. Your design may necessitate moving the
unit back, or cabinets forward to achieve a
flush fit. This will require a minimum rough
opening depth of 25" (635). Refer to the instal-
lation illustration on page 4.
The anti-tip bracket must be installed to
prevent the unit from tipping forward.
Integrated units are compatible with virtually
any style of cabinetry. They can be used with
framed as well as frameless cabinets.
Refer to the full-scale illustrations on pages
14 and 15 for specifics on panels and door
openings.
Door panels can grow beyond 453/8"(1153)
and exceed the 80" (2032) height to accommo-
date any size of door as long as you stay below
the recommended door panel weight limit of
40 lbs (18 kg). Door panels must be a minimum
of 5/8"(16) thick.
The weight of each drawer panel cannot
exceed 12 lbs (5 kg). Drawer panels must be a
minimum of 5/8"(16) thick.
For the bottom drawer, the maximum panel
height is 16 11/16"(424). You must keep a
minimum space of 4" (102) clear below the
bottom edge of the lower drawer panel, so the
unit can be properly vented. In addition, any
decorative base molding must be removable for
possible servicing and cleaning of the
condenser.
Werecommend using D-style handles, which
should be located on the opposite side from the
hinge, centered on the cabinet door and the
top, center area of the drawer panel.
Two Integrated units may be installed next to
one another. Refer to page 11 for additional
information.
A115 volt, 6OHz, 15 amp circuit breaker and
electrical supply are required. A separate circuit,
servicing only this appliance is necessary.
All Integrated models are equipped with a
power supply cord with a 3-prong grounding
plug, which must be plugged into a mating
3-prong grounding type wall receptacle. The
electrical outlet must be placed so the ground-
ing prong is to the right of the thinner blades.
The outlet must be flush with the back wall.
Locate electrical within the shaded area shown
in the installation illustration on page 4.
Do not use an extension cord or two prong
adapter. Electrical ground is required on this
appliance. Do not under any circumstances
remove the power supply cord ground prong.
You must follow all National Electrical Code
regulations. In addition, be aware of local codes
and ordinances when installing your service.
The Integrated Refrigeration Installation
Instructions packed with the appliance will give
you step-by-step procedures for making sure
the unit is installed properly.
Planning Information
Integrated Model 700TR
Dimensions in parentheses are in
millimeters unless otherwise specified. 6
CABINETRY APPLICATIONS
Integrated refrigeration is compatible with virtually any
style and look of cabinetry. The models can be used with
framed as well as frameless cabinets. Because of the
precise application and the look you may want to achieve,
there are important questions you need to answer before
ordering panels for the doors and/or drawers. As you look
at styles of cabinets, keep some important facts in mind:
IMPORTANT NOTE: The depth of each Integrated unit is
24" (610) from the front of the unit to its back. You must
allow for the thickness of the panel you are applying when
planning for the finished rough opening depth if you want
the front panel to be flush with surrounding cabinetry. You
may have to move the unit back into drywall or bring the
cabinets forward to achieve a flush fit.
Weight Limitations –The door panel cannot exceed
40 lbs (18 kg) and each drawer panel must not exceed
12 lbs (5 kg).
Panel Thickness –Door and drawer panels must be a
minimum of 5/8"(16) thick.
The height of the door panel can grow beyond 453/8"
(1153) and exceed the 80" (2032) overall height as long as
you staybelow the recommended door panel weight limit.
The toe kick clearance can vary with the height of the
lower drawer panel; the maximum panel height is 16 11/16"
(424). You must keep a minimum space of 4" (102) clear
below the bottom edge of the lower drawer panel so the
unit can be properly vented.
IMPORTANT NOTE: The inside edges of the rough
opening, as well as the sides and a portion of the backside
of the decorative panels will need to be finished, as they
will be exposed when the door or drawers are open.
Werecommend using D-style handles. For the cabinet
door, handles must be located near the edge of the panel
opposite the hinge, centered top to bottom. Locate
handles in the top center area of the drawer panels.
As the reveal between cabinets
and the Integrated unit decreases,
the potential exists for severe
finger pinching or crushing if a
hand or fingers are placed in the
opening when the door is closing.
Planning Information
Integrated Model 700TR
Dimensions in parentheses are in
millimeters unless otherwise specified. 7
FRAMED CABINETRY APPLICATIONS
Framed cabinetry applications present you with different
questions to address. The illustrations on this page show
common applications of framed cabinetry. These are not
meant to be the only alternatives, but are suggestions
from designers around the country. Also refer to the full-
scale illustrations at the end of this section for specifics
on door openings.
IMPORTANT NOTE: The depth of each Integrated unit is
24" (610) from the front of the unit to its back. You must
allow for the thickness of the panel you are applying when
planning for the finished rough opening depth if you want
the front panel to be flush with surrounding cabinetry. You
may have to move the unit back into drywall or bring the
cabinets forward to achieve a flush fit. Refer to the
illustrations.
Illustrations on the following pages give dimensions for an
Integrated 27" (686) wide tall unit installed within a framed
cabinetry beaded inset application. Review the illustrations,
giving particular attention to the overall panel specifica-
tions. Also refer to the full-scale illustrations at the end of
this section for specifics on door openings.
FRAMED CABINETRY
Traditional Frame – 3/8"(10) offset
(top view).
Traditional Frame – standard overlay
(top view).
Traditional Frame – full overlay (top view).
SUB-ZERO
UNIT
PANEL
CABINET
DOOR
CABINET
FRAME
TO WALL
24
(610)
T
1/8" (3)
REVEAL
1
27
(686)
PANEL
CABINET
DOOR
CABINET
FRAME
SUB-ZERO
UNIT
S
TO WALL
24
(610)
T
1/8" (3)
REVEAL
1
27
(686)
2
PANEL
CABINET
DOOR
CABINET
FRAME
SUB-ZERO
UNIT TO WALL
24
(610)
1
1/8" (3)
REVEAL
2
27
(686)
2
Planning Information
Integrated Model 700TR
Installation of an Integrated 27" (686)
wide tall unit within framed cabinetry.
*Dimensions may vary.
Dimensions in parentheses are in
millimeters unless otherwise specified. 8
A) ALL REVEALS ARE 1/8" (3)
B) DRAWER RAILS ARE ATTACHED TO DRAWER FRONTS
C) BOTTOM RAIL MUST BE REMOVABLE
*DIMENSIONS MAY VARY
CA
A
A
B
B
TOP VIEW
A A
DOOR PANEL
CABINET DOOR
TO WALL
SUB-ZERO
UNIT
PANEL WIDTH
11/2"
(38)
11/2"
(38)
477/8"
(1216)
FRONT VIEW SIDE VIEW
263/4"(679)
139/16"
(345)
151/16"
(383)
84"
(2624)
11/2"
(38)
11/2"
(38)
4"*
(102) 4" (102)
80"*
(2032)
341/2"
(876)*
24"
(610)
27"
(686)
SHADED AREA
INDICATES STATIONARY
STYLES AND RAILS
27"
(686)
24"
(610)
The illustration shows an Integrated 27" (686) wide tall
unit installed within a framed cabinetry beaded inset
application.
IMPORTANT NOTE: Dimensions are based on a 1/8"(3)
reveal. A reveal of up to 1/4"(6) is possible, but panel
dimensions need to be adjusted accordingly.
FRAMED CABINETRY – BEADED INSET APPLICATION
Planning Information
Integrated Model 700TR
9
A
A
A
A) ALL REVEALS ARE 1/8" (3) *DIMENSIONS MAY VARY
SIDE VIEW
24"
(610)
PANEL WIDTH
453/8"
(1153)
263/4"* (679)
139/16"
(345)
1611/16"*
(424)
4"*
(102)
80"*
(2032)
341/2"
(876)*
27"
(686)
FINISHED OPENING
TOE KICK
797/8"*
(2029)
FRAMELESS CABINETRY APPLICATIONS
The illustration below shows a hypothetical installation of
an Integrated 27" (686) wide tall unit within frameless
cabinetry. Review the illustration, giving particular attention
to the overall panel specifications. Also refer to the full-
scale illustrations at the end of this section for specifics
on door openings.
IMPORTANT NOTE: Dimensions are based on a 1/8"(3)
reveal. A reveal of up to 1/4"(6) is possible, but panel
dimensions need to be adjusted accordingly.
FRAMELESS CABINETRY
Installation of an Integrated 27" (686)
wide tall unit within frameless cabinetry.
*Dimensions may vary.
Dimensions in parentheses are in
millimeters unless otherwise specified.
Planning Information
Integrated Model 700TR
Dimensions in parentheses are in
millimeters unless otherwise specified. 10
PANEL CONSIDERATIONS
The illustrations below provide panel
width dimensions for installation of a
27" (686) wide tall unit and for
installing two 27" (686) wide tall units
side by side.
IMPORTANT NOTE: Dimensions are
based on a 1/8"(3) reveal. A reveal of
up to 1/4"(6) is possible, but panel
dimensions need to be adjusted
accordingly.
263
4(679)
3
4(19) PANEL
APPLIANCE
DOOR WIDTH
SUB-ZERO
UNIT
TOBACK
OF UNIT
257
8(657)
27
(686)
24
(610)
CABINETRY
OR SIDE
PANEL
25
(635)
CABINETRY
OR SIDE
PANEL
25
(635)
1
8(3)
REVEAL
min
*
1
8(3)
REVEAL
min
*
*SUBTRACT PANEL WIDTH FROM CABINETRY OPENING TO DETERMINE ACTUAL WIDTH OF REVEAL
C
2613
16 (681) 2613
16 (681)
3
4(19) PANEL 3
4(19) PANEL
DOOR
SUB-ZERO
UNIT
DOOR
SUB-ZERO
UNIT
54 (1372)
TO BACK
OF UNIT
24
(610)
1
8(3)
REVEAL
min
*
1
8(3)
REVEAL
min
*
1
8(3)
REVEAL
min
*
*SUBTRACT PANEL WIDTH FROM CABINETRY OPENING TO DETERMINE ACTUAL WIDTH OF REVEAL
*
CABINETRY
OR SIDE
PANEL
25
(635)
CABINETRY
OR SIDE
PANEL
25
(635)
Panel width dimensions for
installation of a 27" (686) wide
tall unit.
Panel width dimensions for
installation of two 27" (686)
wide tall units side by side.
When 3/4"(19) or thicker panels are used and a reveal
less than 1/4"(6) is maintained, the door panels may
cause damage to the Sub-Zero unit when the door is
open at the maximum 105˚ door stop. You should use
the built-in 90˚ door stop to prevent damage.
Planning Information
Integrated Model 700TR
Dimensions in parentheses are in
millimeters unless otherwise specified. 11
INSTALLATION OPTIONS
The illustrations on this page show some typical
installations and their dimension considerations.
The depth dimension in the illustrations may vary
depending on cabinet styles, treatment of counter-
tops or other design options.
IMPORTANT NOTE: The depth of each Integrated
unit is 24" (610) from the front of the unit to its
back. Your design may necessitate moving the unit
back, or cabinets forward to achieve a flush fit. This
will require a minimum rough opening depth of 25"
(635). Refer to the illustrations.
DUAL INSTALLATIONS
If two or more Integrated models are installed side
byside where there is 2" (51) or less of space
between the units, a heater kit is recommended—
TTDUAL for two tall units installed side by side and
BBDUAL for a tall unit and a drawer unit installed
side by side. These optional components are avail-
able through your Sub-Zero dealer. To obtain local
dealer information, visit the Locator section of our
website,subzero.com.
Installation without side panels.
Installation with side panels.
Installation of two units side byside.
Installation at end of run.
TOP VIEW
CABINETS
25
(635)
C
27
(686)
2
CABINETS
25
(635)
T
27
(686)
2
MINIMUM 5/8" (16) SIDE PANELS
M
TOP VIEW
CABINETS
54
(1372)
25
(635)
C
CABINETS
25
(635)
2
27
(686)
MINIMUM 5/8" (16) SIDE PANELS
Planning Information
Integrated Model 700TR
Dimensions in parentheses are in
millimeters unless otherwise specified. 12
DOOR PANEL HEIGHT
The height of the door panel can grow beyond 453/8"
(1153) and exceed the 80" (2032) overall height, as long as
you stay below the recommended door panel weight limit
of 40 lbs (18 kg).
The illustration below shows how the panel may grow and
what you need to consider doing to finish the area in back
of the door panel.
IMPORTANT NOTE: The valance you use to finish the area
behind the door panel must stay behind the front plane of
the finished molding as shown in the illustration.
IMPORTANT NOTE: The depth of each Integrated unit is
24" (610) from the front of the unit to its back. Your
design may necessitate moving the unit back, or cabinets
forward to achieve a flush fit. This will require a minimum
rough opening depth of 25" (635). Refer to the illustration.
UPPER VALENCE DETAIL
453
8
(1153)
TO
BOTTOM
OF
DOOR
PANEL
TO
FLOOR
1
8
(3)
11
2(38)
TO WALL
DECORATIVE VALANCE
DECORATIVE VALANCE
CANNOT EXTEND BEYOND
THE FRONT OF THIS PLANE
REMOVABLE MOLDING
BY SUB-ZERO
TOP HINGE
25
(635)
*FINISHED HEIGHT OF 80" (2032) IS TO TOP OF SUB-ZERO MOLDING
80*
(2032)
Planning Information
Integrated Model 700TR
Dimensions in parentheses are in
millimeters unless otherwise specified. 13
TOE KICK CLEARANCE
The toe kick clearance can vary with the height of the
lower drawer panel; the maximum panel height is 16 11/16"
(424).
IMPORTANT NOTE: You must keep a minimum space of
4" (102) clear below the bottom edge of the lower drawer
panel so the unit can be properly vented. In addition, any
decorative base molding must be removable for possible
servicing and cleaning of the condenser.
The illustration below shows the area below the lower
drawer where the operating mechanical equipment of the
Integrated unit is housed.
IMPORTANT NOTE: The depth of each Integrated unit is
24" (610) from the front of the unit to its back. Your
design may necessitate moving the unit back, or cabinets
forward to achieve a flush fit. This will require a minimum
rough opening depth of 25" (635). Refer to the illustration.
TOE KICK AREA DETAIL
10 9
16
(268)
16
11
16
(424)
PANEL
PANEL
10
(254)
4
(102)
OPTIONAL
25
8
(67)
4
(102)
TO
911
16
(246)
1
2
(13)
FLOOR
TO WALL
25
(635)
BASE MOLDING MUST
BE REMOVABLE
Planning Information
Integrated Model 700TR
Dimensions in parentheses are in
millimeters unless otherwise specified. 14
FRAMED CABINETRY
IMPORTANT NOTE: The depth of each Integrated
unit is 24" (610) from the front of the unit to its
back. Your design may necessitate moving the unit
back, or cabinets forward to achieve a flush fit.
1
8
3
4
MIN.
(3)
PANEL
SIDE MOLDING AND
INSTALLATION HARDWARE
PROVIDED BY SUB-ZERO
LINE OF INTERFERENCE*
AT MAXIMUM DOOR OPENING
MOUNTING BRACKET SCREW
(19)
FLUSH
FURNITURE
FINISH
LINE OF INTERFERENCE*
TO BACK
OF UNIT
24
(610)
SUB-ZERO DOOR
257
8(657) APPLIANCE DOOR WIDTH
REVEAL
T
24
(610)
LINE OF INTERFERENCE*
SUB-ZERO
DOOR
TO BACK
OF UNIT
Door closed – full scale (top view)
105˚ maximum door opening – 1/4scale (top view)
*If the panel is thicker than 3/4"(19), it is recommended that you
utilize the built-in 90˚ door stop to prevent damage to the panel
and face frame.
Planning Information
Integrated Model 700TR
Dimensions in parentheses are in
millimeters unless otherwise specified. 15
FRAMELESS CABINETRY
IMPORTANT NOTE: The depth of each Integrated
unit is 24" (610) from the front of the unit to its
back. Your design may necessitate moving the unit
back, or cabinets forward to achieve a flush fit.
1
8MIN.
(3)
REVEAL
3
4PANEL
LINE OF INTERFERENCE*
AT MAXIMUM DOOR OPENING
MOUNTING BRACKET SCREW
(19)
TO BACK
OF UNIT
24
(610)
SIDE MOLDING AND
INSTALLATION HARDWARE
PROVIDED BY SUB-ZERO
LINE OF INTERFERENCE*
SUB-ZERO DOOR
257
8(657) APPLIANCE DOOR WIDTH
TO
WALL
24
(610)
LINE OF INTERFERENCE*
SUB-ZERO DOOR
3/4"(19) DOOR PANEL
SIDE PANEL
COUNTERTOP
105˚ maximum door opening – 1/4scale (top view)
Adjacent side panel and countertop application
Door closed – full scale (top view) *If the panel is thicker than 3/4"(19), it is recommended that you
utilize the built-in 90˚ door stop to prevent damage to the panel
and face frame.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
Sub-Zero 700TR is a tall refrigerator unit with upper cabinet refrigerator and refrigerator storage drawers. It has a 15.5 cu ft storage capacity, dual refrigeration system, and electronic digital controls. The unit is designed for "point-of-use" refrigeration and can be integrated into your cabinetry for a seamless look. The adjustable shelves, drawers, and door compartments allow for flexible storage options. The unit also features an audible door alarm to alert you if a door or drawer is left open.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Sub-Zero 700 Series Refrigeration User manual
-
Sub-Zero ID-36R Specification
-
Sub-Zero 736TI Troubleshooting guide
-
-
-
-
Wolf I700BR User manual
-
Sub-Zero ICBB-36R User manual
-
Sub-Zero 400 Series Wine Storage Design Guide
-
Sub-Zero 736TFI User manual