CURT 13149 User manual

CURT
Brand
CURT
Model
13149
Type
User manual

CURT 13149 is a vehicle-specific trailer hitch custom-designed for the Toyota RAV4 (excluding electric models). It provides a safe and reliable towing solution, allowing you to transport trailers, bikes, or other equipment with ease. With a gross load capacity of 3,500 lbs. for weight carrying and 4,000 lbs. for weight distribution, it's ideal for a variety of towing needs. Installation is straightforward, requiring no drilling and utilizing existing weld nuts on the vehicle's frame. Detailed instructions and all necessary hardware are included.

CURT 13149 is a vehicle-specific trailer hitch custom-designed for the Toyota RAV4 (excluding electric models). It provides a safe and reliable towing solution, allowing you to transport trailers, bikes, or other equipment with ease. With a gross load capacity of 3,500 lbs. for weight carrying and 4,000 lbs. for weight distribution, it's ideal for a variety of towing needs. Installation is straightforward, requiring no drilling and utilizing existing weld nuts on the vehicle's frame. Detailed instructions and all necessary hardware are included.

PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE ALL FASTENERS ARE TIGHT AND ALL STRUCTURAL COMPONENTS ARE SOUND
CURT Manufacturing LLC. warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective, Curt Manufacturing LLC. may repair or replace
the product at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of this product voids the warranty. Curt Manufacturing LLC.'s liability is limited to repair or replacement
of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage.
For more information log onto www.curtmfg.com, & for helpful towing tips log onto www.hitchinfo.com
MAKE: STYLE:
MIN.
15
WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY
WEIGHT CARRYING:
INSTALLATION TIPS:
INSTALLATION REQUIRES:
VEHICLE PHOTO:
HITCH ILLUSTRATION:
REPRESENTATIVE PHOTO
MAKE SURE YOUR HITCH MATCHES
LEVEL OF DIFFICULTY:
EASY
EASY MODERATE CHALLENGING
1. BEFORE YOU BEGIN INSTALLATION, READ ALL
INSTRUCTIONS THOROUGHLY.
2. TO EASE INSTALLATION, 2 PEOPLE MAY BE
REQUIRED.
3. USING PROPER TOOLS WILL GREATLY IMPROVE
THE QUALITY OF THE INSTALL AND REDUCE THE
TIME REQUIRED.
4. NEED HELP OR HAVE SOME QUESTIONS?
CALL TECHNICAL SUPPORT AT 800.798.0813
Safety glasses should be
worn at all times while
installing this product
.
YEARS:
2006-CURRENT TOYOTA MODEL:
RAV4 (EXCEPT ELECTRIC)
COMPACT SUV
3,500
525
TRAILER WEIGHT:
TONGUE WEIGHT:
13149 INSTALLATION INSTRUCTIONS
LBS.
LBS.
1/28/2015
WEIGHT DISTRIBUTION:
TRAILER WEIGHT:
TONGUE WEIGHT:
4,000
525
LBS.
LBS.
MIN.
30
IF YOU ARE HESITANT TO UNDERTAKE
THIS TASK ON YOUR OWN, CONTACT AN AUTHORIZED
CURT INSTALLER FOR ADDITIONAL ASSISTANCE.
NOVICE INSTALL TIME:
PRO INSTALL TIME:
SOCKETS
17mm
19mm
WIRE PIPE
BRUSH
RATCHET
TORQUE
WRENCH
SOCKET
EXTENSION
8"
PART REMOVAL
CLEAN EXISTING WELD NUTS
USING A PIPE BRUSH
NO DRILLING RQUIRED
REMOVE TIE DOWN BRACKET
LOWER EXHAUST
INSTALLATION WALKTHROUGH:
For more information log onto www.curtmfg.com, & for helpful towing tips log onto www.hitchinfo.com
DESCRIPTIONPART NUMBERQTYITEM
HEX BOLTM12-1.25 x 35mm41
CONICAL TOOTHED WASHER1/2"42
1. If present remove panel and trim using panel trim
diagram below as reference. Remove the tie
down bracket from the drivers side frame rail
using the 17mm socket, 8" extension and ratchet.
Return the bracket and fasteners to vehicle owner.
2. Lower rear most exhaust isolator for ease of
installment.
2
1
DRIVER SIDE FRAME RAIL
PASSENGER SIDE FRAME RAIL
EXISTING WELDNUTS
(BOTH SIDES)
PANEL TRIM DIAGRAM
1.500 in
USE RIB
AS GUIDE
INSTALLATION WALKTHROUGH:
For more information log onto www.curtmfg.com, & for helpful towing tips log onto www.hitchinfo.com
3. Raise hitch into position over existing weldnuts
and install the supplied 12mm hex bolts and
conical tooth washers as shown.
4. Raise exhaust back into location and reinstall
rubber isolator.
5. Torque hardware to 86 lb-ft.
Install now complete
TOWING SAFETY INFORMATION
GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT.
GROSS LOAD CAPACITY WHEN USED AS A WEIGHT DISTRIBUTION HITCH: LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT
***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.***
HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT 1-800-798-0813
INSTALLATION STEPS
PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERS
ARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND.
Curt Manufacturing LLC., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective,
Curt Manufacturing LLC., may repair or replace the product, at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of
this product voids the warranty. Curt Manufacturing LLC.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or
consequential loss or damage.
3,500 525
4,000
525
TOYOTA RAV 4 (EXCLUDING ELECTRIC)
1/28/2015
13149
30
34
15
HITCH WEIGHT:
LBS.
INSTALL TIME
PROFESSIONAL: MINUTES
NOVICE (DIY): MINUTES
INSTALL NOTES:
Parts List
DESCRIPTIONPART NUMBERQTYITEM
HEX BOLTM12-1.25 x 35mm
4
1
CONICAL TOOTHED WASHER1/2"
42
1. If present remove panel and trim using panel trim diagram above as reference.
Remove tie down bracket from the driver's side of the vehicle and return to vehicle owner.
2. Lower rear most exhaust isolator for ease of installment.
3. Raise hitch into position over existing weldnuts and install the supplied 12mm hex bolts and conical tooth
washers as shown.
4. Raise exhaust back into location and reinstall rubber isolator.
5. Torque hardware to 86 lb-ft.
PASSENGER SIDE
FRAME RAIL
EXISTING WELDNUTS
(BOTH SIDES)
TOOLS REQUIRED
17, 19mm SOCKET
8" EXTENSION
SOCKET WRENCH
TORQUE WRENCH
- EXISTING WELDNUTS
- NO DRILLING REQUIRED
- REMOVE TIE DOWN BRACKET
- LOWER EXHAUST
1
2
DRIVER SIDE FRAME RAIL
USE RIB AS GUIDE
PANEL TRIM DIAGRAM
1.500 in
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

CURT 13149 User manual

CURT
Brand
CURT
Model
13149
Type
User manual

CURT 13149 is a vehicle-specific trailer hitch custom-designed for the Toyota RAV4 (excluding electric models). It provides a safe and reliable towing solution, allowing you to transport trailers, bikes, or other equipment with ease. With a gross load capacity of 3,500 lbs. for weight carrying and 4,000 lbs. for weight distribution, it's ideal for a variety of towing needs. Installation is straightforward, requiring no drilling and utilizing existing weld nuts on the vehicle's frame. Detailed instructions and all necessary hardware are included.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents