Scott Living 1022MR-24-V01 Installation guide

Questions, problems, missing parts?

Before returning to your retailer,

call our customer service department at

1-855-571-1044

8 a.m. - 8 p.m., EST, Monday - Friday.

www.greentouchchinaltd.com

Français p. 10

Español p. 19

Date Purchased _______________________

Mirror

MODEL # 1022MR-24-V01

ASSEMBLY, CARE & USE INSTRUCTIONS

ITEM # 0819969

TM

PACKAGE CONTENTS

2

PART DESCRIPTION QUANTITY

A Mirror 1

B Main Body (preassembled to Mirror (A)) 1

A

B

HARDWARE CONTENTS (NOT SHOWN ACTUAL SIZE)

PRODUCT SPECIFICATION

3

PART DESCRIPTION QUANTITY

AA Wall Mount Screw 4

BB Drywall Anchor 4

AA BB

Power Input: 120VAC / 60 Hz

Power Rating: Max. 17W

LED Light Color: Warm White

20-7/8in

12-3/4in

29in

3-3/8in 3-3/8in

16-3/4in

7-9/16in

1in

1/4in

1-1/2in

24in

36in

SAFETY INFORMATION

IMPORTANT SAFETY INSTRUCTIONS

4

When using an electrical furnishing, basic precautions should always be followed, including the following:

Read all instructions before using this mirror.

DANGER – To reduce the risk of electric shock:

1. Always unplug the power cord before cleaning around the electrical components.

WARNING – To reduce the risk of burns, fire, electric shock, or injury to persons:

1. Unplug from outlet before putting on or taking off parts.

2. The appliance is not to be used by persons (including children) with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge, unless they have been given supervision or

instruction. Children should be supervised to ensure that they do not play with the appliance.

3. Use this furnishing only for its intended use as described in these instructions. Do not use

attachments/accessories not recommended by the manufacturer.

4. Never operate this furnishing if it has a damaged cord or plug, if it is not working properly, if it has

been dropped or damaged, or dropped into water. Return the furnishing to a service center for

examination and repair.

5. Never drop or insert any object into any opening.

6. For household and dry locations use only.

7. Do not use outdoors.

8. Never operate the furnishing with the air openings blocked. Keep the air openings free of lint, hair, and

the like.

9. Do not operate where aerosol (spray) products are being used or where oxygen is being administered.

Please read and understand this entire manual before attempting to assemble, operate or install the

product.

This equipment has been tested and found to comply with the limits for Class B digital devices,

pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. The equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio or television reception, which can be determined by turning the equipment

off and on. The user is encouraged to try and correct the interference by one or more of the following

measures:

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may cause undesired

operation.

Modifications not approved by the party responsible for compliance could void user’s authority to

operate the equipment.

This Class B digital apparatus complies with Canadian ICES-005.

Reorient or relocate the receiving antenna

Increase the separation between the equipment and the receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

•

PREPARATION

MOUNTING OPTIONS

10. To disconnect, turn all controls to the off position, then remove plug from outlet.

11. WARNING: Risk of Electric Shock – Connect this furnishing to a properly grounded outlet only. See

Grounding Instructions.

12. Keep the cord away from heated surfaces.

SAVE THESE INSTRUCTIONS

SAFETY INFORMATION

5

GROUNDING INSTRUCTIONS

This product is for use on 120 volts. The cord has a plug as shown below. See illustration for grounding

instruction. An adapter as shown at (C) is available for connecting three-blade grounding type plugs to

two slot receptacles. The green grounding lug extending from the adapter must be connected to a

permanent ground such as a properly grounded outlet box. The adapter should not be used if a three-slot

grounded receptacle is available.

WARNING: Before beginning assembly of product, make sure all parts are present. Compare parts with

package contents list and hardware contents list. If any part is missing or damaged, do not attempt to

assemble the product.

Secure main body (B) to wall

using screws (AA)(included) at

marked stud locations.

Screw wall anchors (BB)(included) flush

into desired wall location. Secure main

body (B) onto wall using provided screws

(AA)(included) into wall anchors (BB).

Drill holes at marked locations,

then insert wall anchors (not

included) into holes. Secure

the main body (B) to wall using

fasteners (not included).

Estimated

Assembly Time:

20 Minutes

Helpful Tools

(not included):

Tape Measure

Level

Tools Required for

Installation (not included):

Phillips Screwdriver

STUD WALL: DRYWALL: CONCRETE WALL:

(CONT’D)

A B C D

Grounding Pin

Grounding Means

Metal

Screw

Cover of

Grounding

Box

Adapter

1

ASSEMBLY INSTRUCTIONS

Place the mirror assembly face down on a soft clean

surface such as the styrofoam sheet included in the

packaging. Take care to not scratch or damage the

mirror surface.

1.

Unscrew two screws (DD) located on both sides of the

main body (B).

2.

6

DD

3

A

B

Lift the main body (B) from the mirror (A) and set a side.3.

2

DD

ASSEMBLY INSTRUCTIONS

Using the dimension drawings on page 3, determine the

desired location for the mirror. Take into account you

should have a 3 inch minimum clearance between the

bottom of the mirror and the top of the faucet/vanity.

Use the main body (B) to mark the screw locations on

the wall.

Note: Make sure it is level.

Note: The installation location has to have power outlet

inside of main body (B) as shown

4.

Secure the main body (B) to the wall using screws (AA)

or the hardware best suited for your wall type. Refer to

Mounting Options on page 5. Be careful to not drill into

hidden electrical or plumbing lines inside the wall when

mounting main body (B) to wall.

5.

7

With the help of another adult, hold mirror (A) away

from the main body (B), connect the quick connect

wires (1), then plug the power cord into the wall outlet

(2). Secure power cord to avoid contact with sharp

objects.

6.

4

B

5

B

AA

Hardware Used

Wall Mount Screw

Drywall Anchor

x 4

AA

BB

(CONT’D)

AA

BB

6

A

B

2

1

ASSEMBLY INSTRUCTIONS

Align the hook on the back of the mirror (A) with the

receiving bracket on the main body (B). Carefully lower

the hook into the receiving bracket.

WARNING: Make sure it feels fully seated and secure

before releasing the mirror (A).

Back Light

The touch switch on the front of the mirror is to turn the

back light ON/OFF.

When the back light is powered ON the button color will

glow Blue; when it is in standby mode it will glow Red.

Adjust Brightness of the Back Light

When the back light is powered ON, press and hold the

power button for approximately 3 seconds. The

brightness will scroll up then back down. Take your

finger off the touch button to leave the brightness at the

setting you choose. This brightness setting will be

retained in memory. To adjust the brightness repeat the

above steps.

•

7.

8

7

A

B

Re-install the screws (DD) on both sides as shown.8.

8

A

OPERATING INSTRUCTIONS

Touch Switch

(CONT’D)

DD

The glass can be cleaned using standard household glass cleaning agents.

Any other servicing should be performed by an authorized service representative.

The manufacturer warrants this item against defects in materials and workmanship for a period of one

(1) year from the date of original retail purchase. This warranty applies only to the original purchaser.

This warranty does not apply to any damage on the product by accident, misuse, or modified,

improper installation or by affixing accessories not produced by the manufacturer. The manufacturer

is not accountable whatsoever for product installation during the warranty period. There is no further

expressed warranty. The manufacturer shall not be legally responsible for incidental, consequential

or special damages arising at or in connection with product use or performance except as may

otherwise be accorded by law. The manufacturer disclaims any and all implied warranties.

•

CARE AND MAINTENANCE

WARRANTY

9

For replacement parts, call our customer service department at 1-855-571-1044, 8 a.m. - 8 p.m., EST,

Monday - Friday.

REPLACEMENT PARTS

AA CC DDBB

PART DESCRIPTION PART #

AA Wall Mount Screw MWA-2.5x3.1-SET2

MWA-2.5x3.1-SET2

PU16-AED15-1400ILS-LD

BB Drywall Anchor

PU16-0.9x0.4-SSDD Screw

CC LED Driver

Page is loading ...

Scott Living 1022MR-24-V01 Installation guide

Scott Living 1022MR-24-V01 Installation guide

in other languages

Related papers

Other documents