Page is loading ...
ASSEMBLY INSTRUCTIONS
RiverRidge® MEDFORD TALL CABINET
ITEM# 06-106 WHITE
ITEM# 06-107 ESPRESSO
ADULT ASSEMBLY REQUIRED
This product requires assembly by an adult because of small parts. Care should be taken
in unpacking and assembling this item to keep small parts away from children.
WARNING SEE FULL WARNING ON PAGE 2
Young children can be seriously injured or killed if furniture tips over. Don’t use this
item for a TV stand or place heavy objects on top of item. Always use angle-braces or
anchors to secure furniture to the wall.
Send requests for missing or damaged parts by email to: customer.service@ssi-rr.com or
call toll free 1-(844)-223-5201 or order parts on line at www.riverridgehome.com
THIS SHELF UNIT WILL HOLD UP TO 25 POUNDS PER SHELF OR A TOTAL OF 100 POUNDS. DO
NOT LOAD EACH SHELF WITH MORE THAN 25 POUNDS OR 100 POUNDS TOTAL WEIGHT. IF
OVERLOADED WITH MORE THAN 25 POUNDS PER SHELF OR 100 POUNDS TOTAL WEIGHT,
SHELF MAY TIP FROM THE WALL AND CAUSE SERIOUS INJURY OR DEATH.
PARTS LIST
NO QTY DESCRIPTION
1 1PC TOP BOARD
2 1PC UPPER LEFT SIDE PANEL
3 1PC UPPER RIGHT SIDE PANEL
4 1PC TOP SHELF
5 1PC MIDDLE CONNECTION BOARD
6 1PC DOOR
7 1PC ADJUSTABLE SHELF
8 1PC BOTTOM BOARD
9 1PC LOWER LEFT SIDE PANEL
10 1PC LOWER RIGHT SIDE PANEL
11 2PCS UPPER BACK BOARD
12 1PC LOWER BACK BOARD
NO
PARTS QTY DESCRIPTION
A
14PCS CAM BOLT
B
14PCS CAM LOCK
C
8PCS WOOD DOWEL
D
1PC MAGNET
E
10PCS SCREW 3x14mm
F
2PCS METAL BRACKET
G
2PCS SCREW 3x10mm
H
4PCS SHELF HOLDER
I
5PCS SCREW 4x35mm
J
1PC MAGNET PLATE
K
2PCS DOOR PIN
L
1PC SCREW 4x25mm
M
1PC KNOB
N
1PC PLASTIC LOCK STRAP
O
1PC PLASTIC ANCHOR
P
8PCS PLASTIC BRACKET
TOOLS NEEDED FOR ASSEMBLY: FLAT & PHILLIPS SCREWDRIVER (NOT INCLUDED)
THE USE OF POWER SCREWDRIVER IS NOT RECOMMENDED FOR ASSEMBLY
TOOL NEEDED FOR SECURING TO WALL: POWER DRILL (NOT INCLUDED)
STEP 1
STEP 1
1. Screw 4 cam bolts (A) into pre-threaded holes on top board (1).
2. Attach 1 metal bracket (F) to top board (1) by inserting 1 screw (G) through hole on metal bracket (F)
and tighten to top board (1).
3. Screw 4 cam bolts (A) into pre-threaded holes on middle connection board (5).
4. Attach magnet (D) to middle connection board (5) by inserting 2 screws (E) through holes on magnet (D)
and tighten to middle connection board (5).
STEP 2
STEP 2
1. Screw 1 cam bolt (A) into pre-threaded hole on upper left side panel (2).
2. Screw 1 cam bolt (A) into pre-threaded hole on upper right side panel (3).
STEP 3
STEP 3
1. Screw 2 cam bolts (A) into pre-threaded holes on lower left side panel (9).
2. Screw 2 cam bolts (A) into pre-threaded holes on lower right side panel (10).
STEP 4
STEP 4
1. Attach magnet plate (J) to door (6) by inserting 1 screw (G) through hole on magnet plate (J) and
tighten to door (6).
2. Attach knob (M) to door (6) by inserting 1 screw (L) through hole on door (6) and tighten to knob (M).
3. Insert 2 door pins (K) into holes on door (6).
STEP 5
STEP 5
1. Insert 2 wood dowels (C) into wood dowel holes on upper left side panel (2).
2. Attach top shelf (4) to upper left side panel (2) by inserting wood dowels (C) into wood dowel holes and
inserting cam bolts (A) into cam lock holes on top shelf (4).
3. Insert cam lock (B) into cam lock hole on top shelf (4) and rotate clockwise to secure cam bolt in place.
4. Repeat above steps to assemble upper right side panel (3) to top shelf (4).
STEP 6
STEP 6
1. Slide 1 upper back board (11) into grooves on upper left side panel (2), upper right side panel (3) and
top shelf (4).
2. Insert 2 wood dowels (C) into wood dowel holes on upper left side panel (2) and upper right side panel
(3).
3. Attach middle connection board (5) to upper left side panel (2), upper right side panel (3) and upper
back board (11) by aligning upper back board (11) with groove on middle connection board (5) and
inserting wood dowels (C) into wood dowel holes on middle connection board (5).
4. Insert 4 screws (I) through holes on middle connection board (5) and tighten to upper left side panel (2)
and upper right side panel (3).
STEP 7
STEP 7
1. Slide upper back board (11) into grooves on upper left side panel (2), upper right side panel (3) and
top shelf (4).
2. Attach top board (1) to upper left side panel (2), upper right side panel (3) and upper back board (11)
by aligning upper back board (11) with groove on top board (1) and inserting cam bolts (A) into cam
lock holes on upper left side panel (2) and upper right side panel (3).
3. Insert 4 cam locks (B) into cam lock holes and rotate clockwise to secure cam bolts in place.
STEP 8
STEP 8
1. Insert 1 wood dowel (C) into wood dowel hole on lower left side panel (9).
2. Attach bottom board (8) to lower left side panel (9) by inserting wood dowel (C) into wood dowel hole
and inserting cam bolts (A) into cam lock holes on bottom board (8).
3. Insert 2 cam locks (B) into cam lock holes on bottom board (8) and rotate clockwise to secure cam bolts
in place.
4. Repeat above steps to assemble lower right side panel (10) to bottom board (8).
5. Slide lower back board (12) to grooves on lower left side panel (9), lower right side panel (10) and
bottom board (8).
STEP 9
STEP 9
1. Attach door (6) to bottom board (8) by inserting door pin (K) into door pin hole on bottom board (8).
2. Attach pre-assembled upper unit to pre-assembled lower unit by inserting door pin (K) into door pin hole
on middle connection board (5) and inserting cam bolts (A) into cam lock holes on lower left side panel
(9) and lower right side panel (10).
3. Insert 4 cam locks (B) into cam lock holes on lower left side panel (9) and lower right side panel (10),
then rotate clockwise to secure cam bolts in place.
STEP 10
STEP 10
1. Insert 4 shelf holders (H) into holes on lower left side panel (9) and lower right side panel (10) and make
sure all 4 holders are on same level.
2. Place adjustable shelf (7) onto shelf holders (H).
STEP 11
STEP 11
1. Attach 8 plastic brackets (P) to back of cabinet by inserting 8 screws (E) through holes on plastic
brackets (P) and tighten to cabinet.
STEP 12
STEP 12
1. Place drawing with hole position on wall in desired location and drill 1 hole through the hole position on
the drawing.
2. Insert plastic anchor (O) into hole and attach metal bracket (F) to plastic anchor (O) by inserting 1 screw
(I) through hole on metal bracket (F) and tighten to plastic anchor (O).
3. Place cabinet against wall and insert 1 plastic lock strip (N) through metal bracket (F) on cabinet and
metal bracket (F) on wall.
4. Fasten plastic lock strip (N) to secure 2 metal brackets together firmly.
/
