AG-40 Digital Grande Piano
Easy Assembly Guide
IF YOU HAVE ANY QUESTIONS OR PROBLEMS
PLEASE CALL OUR TOLL FREE HELPLINE
ASSEMBLY GUIDE
888-998-9848
DO NOT RETURN TO THE STORE
What’s Included:
Assembly:
a
b
c
d
e
f
g
h
j
i
k
IMPORTANT NOTE:
DO NOT ATTEMPT TO ASSEMBLE UNIT
WITHOUT HELP.
2 OR MORE PERSONS REQUIRED FOR
ASSEMBLY.
A. Lyre
B. Right Leg
C. Le Leg
D. Rear Leg
E. Piano Body
F. Leg Bolt x 6
H. Lyre Support Rod Screws x 8
I. Lyre Support Rods x 2
J. Wrench
G. Lyre Bolts x 2 K. Screwdriver
L. Washers
l
UNBOXING YOUR PIANO
1. Begin assembly by placing the main piano unit on its side,on a padded or carpeted surface, as shown.
Not pictured:
SD Memory Card, Documentation,
AC Power Cable.
LEG BOLT
LYRE BOLT
PIANO ASSEMBLY (CON’T)
2. Leaving piano on side, attach the lyre assembly and the top and rear legs, as shown. Attach using the cor-
rect bolts and washers, as shown below. DO NOT ATTACH BOTTOM LEG AT THIS POINT.
3. Attach Lyre supports to the lyre and piano body as shown, using two lyre screws at each point shown.
upright position
PIANO ASSEMBLY (CON’T)
4. Position a pillow or thick blanket so that the pedal assembly will rest upon it when the piano is turned
upright.
5. With the lyre, top leg and rear leg rmly secured, li and rotate piano in a tipping motion to the upright
position.
blanket
!
Ensure that two to three
people undertake steps
4,5 & 6 of the assembly.
!
!
ADJUSTING THE PEDAL FEET
8. With your piano placed in its nal position, locate the two pedal feet on the bottom of the lyre as shown
in the picture below. Turn each foot counter-clockwise until they make rm contact with the oor surface.
If you relocate the piano in the future, be sure to raise the pedal feet back up by turning them clockwise pri-
or to doing so to avoid damage to the pedal feet and lyre assembly.
PIANO ASSEMBLY (CON’T)
6. Attach the bottom leg using the correct bolts and
washers as shown above. Once the bottom leg is
secured to the piano, one person may need to li the
front of the piano slightly so that the other person
may remove the blanket from under the piano.
7. Once the blanket is removed from underneath
of the lyre, locate the CAT5 cable that is attached to
the lyre. Plug the CAT5 cable into the receptacle as
shown in the picture. (g 1) Locate the AC power
chord receptacle underneath of the piano and plug in
the provided power cable. (g 2)
(g 1)
(g 2)
!
If you have any questions about your piano please contact us
toll free 888 - 998 - 9848
Virgin (VMI) is the Parent Company of Artesia Pianos
Virgin Musical Instrument Company
P.O. BOX 2908
LA MESA, CA 91943
info@virginmusicalinstruments.com
www.virginmusicalinstruments.com
PIANO BENCH ASSEMBLY
9. To assemble the bench, insert the threaded leg rod through a metal bracket (located on all four corners
underneath of the padded top). Secure each leg with a locking washer and nut, then tighten with the wrench
provided as shown in the picture below.
Padded Bench
Locking Washer (4)
Wrench
Nut (4)
Leg (4)
Locking Washer
Metal Bracket
Leg Rod
Nut
-
1
-
2
-
3
-
4
-
5
-
6
