ATA KPX-5 User manual

Brand: ATA

Model: KPX-5

Category: Numeric keypads

Type: User manual

ATA KPX-5 is a wireless digital keypad that allows you to control access to your garage door, gate, or other devices with a numeric code. With a capacity to store up to 20 unique 4-8 digit codes, it provides secure and convenient keyless entry for multiple users. The keypad features a built-in backlighting for easy operation in low-light conditions and a battery level monitor to alert you when the battery needs replacement. Additionally, it has a tamper alarm that sounds after three consecutive incorrect code entries, enhancing security against unauthorized access.

Thank you for purchasing the ATA SecuraCode

Wireless

Digital Keypad. Familiarise yourself with the following

instructions prior to commencing set up. Store this information

including codes in a safe place for future reference.

OPERATION

To open a door or gate using the keypad transmitter simply

enter a valid code via the numerical buttons followed by one of

the programmed channel buttons. Up to 20 individual codes can

be stored in the keypads memory.

The keypad is supplied with a factory preset code (1111)

which must be changed to a new number before the

keypad will operate. A code can be any 4-8 digit number except

8888 8888. Refer to the initial set up sequence below.

INITIAL SET UP

1. Press and hold Channel 1 (CH1) (Fig. 1) until a long beep

is heard.

2. Press 1111 then CH1.

3. Enter new code (eg 1234) then CH1.

4. Repeat Step (3) (within 3 seconds) to confirm.

CODING THE KEYPAD INTO THE OPENER

1. Press and hold the blue Door Code button on the control

panel of your ATA garage door opener (Fig. 2) or SW1/SW2

on the receiver board (Fig. 3 & 4).

2. Enter your PIN code then press one of the four channel

buttons (CH1 - CH4) you wish to use to operate the door or

gate etc.

3. Press the same CH button again.

4. Release Door Code or SW button. The CH button should

now be stored into the opener's memory.

5. Test operation of the Keypad. Enter a valid code followed by

the stored CH button.

Note: You only need to program the CH button once as all users

will have the same access privaleges once a valid code

has been entered.

ADDING AN ADDITIONAL PIN CODE

A user code can be any number of 4 to 8 digits except 1111 or

8888 8888.

1. Press and hold CH4 until a long beep is heard.

2. Enter any existing code followed by CH4.

3. Enter the new code followed by CH4.

4. Repeat step 4 to confirm.

5. Test operation using the new code.

CHANGING A STORED CODE

One code must remain in memory for adding, changing or

deleting additional codes.

WARNING: Changing a code to 8888 8888 will delete it.

Note: There is a timeout of approximatey 10 seconds after the

last button is pressed.

1. Press and hold CH1 until a long beep is heard.

2. Enter the code that is to be changed followed by CH1.

3. Enter the new code followed by CH1.

4. Repeat step 3 (within 3 seconds) to confirm.

5. Test operation using the new code. You should hear a

continuous string of beeps.

KPX-5 Wireless Digital Keypad Instruction Manual

KPX-5 Wireless Digital Keypad

GDO-2 & GDO-4 Garage Door Opener Control Panel

CRX-2 Stand Alone Receiver

SW1 SW2

RX-2 Receiver Board

SW1 SW2

Fig. 1

Fig. 2

Fig. 3

Fig. 4

DELETING A STORED CODE

One code is always required for adding new/additional codes.

1. Wait for the current code to timeout (if one is entered).

2. Press and hold CH1 until a long beep is heard.

3. Enter the code that is to be deleted followed by CH1.

4. Enter 8888 8888 followed by the CH1.

5. Repeat step 4 to confirm.

6. Test operation to ensure that the deleted code does not

operate the transmitter. This procedure is the same as

changing the code to 8888 8888.

USING THE KEYPAD BACK LIGHT

To illuminate the keypad press one of the CH buttons briefly

before the code is entered. The keypad will remain

illuminated for 10 seconds after the last key is released.

BATTERY LEVEL MONITOR

The keypad has a built in battery monitor that indicates when

the battery level is low by altering the normal transmission

sound to a 'slowing down' effect.

TAMPER ALARM

If more than three incorrect codes are entered in sequence, the

keypad will sound a tamper alarm for 10 seconds before

resuming normal operation. If another incorrect code is entered,

the tamper alarm will sound again. This situation will repeat for

each incorrect code until a valid code is entered, even if the

battery is removed and then reconnected.

KEEPING CODE RECORDS

It is important to keep records of the entered codes in a safe

place so that forgotten codes can be recalled and codes can be

deleted when no longer required. Use the table below to record

your user codes and store for future reference.

Automatic Technology Australia Pty Ltd

17-19 Advantage Road Highett Vic 3190 Australia

T: +61 3 9532 2788 F: +61 3 9532 2799

E: [email protected] W: www.ata-aust.com.au

is a registered trademark of Automatic Technology Australia P/L.

In an ongoing commitment to product quality ATA reserve the right to change specifications without notice. Printed for Export.

NOTE: If you lose or forget a code you will need to return the

keypad to ATA for reprograming. A charge will apply

for this service.

WARRANTY

Subject to all of the matter set out below, Automatic

Technology Australia Pty Ltd (“ATA”) warrants for twelve (12)

months from the date of purchase (specified in the tax invoice

receipt) that the KPX-5 Wireless Digial Keypad (the “Product”)

is free of any defects in material and workmanship rendering it

unmerchantable.

This warranty referred to above applies only where:

a) the consumer seeking to rely on the said warranty;

1) returns the Product which it claims to be defective; and

2) presents the relevant sales docket and this warranty

document, to the retailer from whom the Product was

purchased to confirm that date of purchase; and

b) the purchaser notified ATA or the retailer from whom the

Product was purchased of the alleged defect in the Product

immediately upon experience or learning of the alleged

defect.

Except for the warranty against defects in material andwork-

manship set out above, ATA gives no warranties of any kind

whatsoever, whether express or implied or whether statutory or

at common law, in relation to the Product, and all warranties of

fitness for particular purpose and other warranties of

whatsoever kind relating to the Product are hereby declaimed.

Without limiting the generality of the foregoing, ATA disclaims

any liability of whatsoever nature in respect of any claim or

demand loss or damage which arise out of;

a) accidental damage to or normal wear and tear to the Product

or to the Product’s components;

b) flood, rain, water, fire or lightning;

c) incorrect, improper or unreasonable maintenance and/or use;

d) installation, adjustment or use other than ATA which is not in

accordance with the instructions set out in installation

instructions incorporated in the document;

e) attempted or complete modification or repairs to the Product

carried out by a person who is not authorised by ATA to

carry out such modification or repairs;

f) radio (including citizen band transmission) or any electronic

interference,

g) damage caused by electrical surges,

h) damage caused by insects.

ATA’s liability under the warranty set out above is limited, at

ATA’s absolute option, to replacing or repairing the Product

which ATA, in its unfettered opinion, considers to the defective

either in material and/or workmanship or to credit the consumer

with the price at which the Product was purchased by the con-

sumer. Where the Product is retailed by any person other than

ATA, except for the warranty set out above, such person has no

authority from ATA to give any warranty or guarantee on ATA’s

behalf in addition to the warranty set out above.

USER CODE NOTES

ATA KPX-5 User manual

Brand: ATA

Model: KPX-5

Category: Numeric keypads

Type: User manual

Download PDF

report

ATA KPX-5 User manual

ATA KPX-5 User manual

Related papers

Other documents