2. Computers & electronics
  3. Telecom & navigation
  4. Mobile phones
  5. Car kits
  6. MUTOH
  7. ValueJet VJ-1204
ValueJet VJ-1204

MUTOH ValueJet VJ-1204 User Maintenance And Cleaning Manual

  • Hello! I am an AI chatbot trained to assist you with the MUTOH ValueJet VJ-1204 User Maintenance And Cleaning Manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • How often should I clean the wiper?
    What supplies do I need to clean the VJ-1204?
    How do I clean the wiper?
    How do I clean around the cap?
    How do I clean around the print head?
VJ-1204
User
Maintenance
and Cleaning
Guide
Page 1 of 9
ATTENTION: This is a supplementary document and is to be
used in conjunction with the ValueJet 1204 User Operations Manual.
Please refer to Section 4: Daily Maintenance of the Quick Reference
Guide or Section 6: Maintenance of the Operation Manual CD, for
complete step by step instructions for performing these items.
Section 1: Intervals
User Level Maintenance Intervals VJ-1204
1-2 times per week Once a week Every 1-2 Months
□ Clean Wiper
□ Clean around cap
□ Clean Around Print
Head
□ Replace Flushing Box
Sponge
Section 2: Supplies
1. Supplies for cleaning the VJ-1604 can purchased as a kit P/N: 11608-0001
6
5
4
3
2
1
Item # Description Qty
1 Tweezers 1
2 Foam Swabs 25
3 250ml bottle eco-cleaning 36
4 Flushing Box Insert w/ Pad 1
5 Rubber Gloves 5 pair
6 Lint Free Cloth 36
Please Note: If item #6 is not present please use Isopropyl Alcohol only.
Page 2 of 9
Section 3: Cleaning Procedures
** Clean Wiper
Do not touch Wiper. Oil from your hands may prevent the wiper from cleaning the
head properly.
1. The wiper can be cleaned using either the foam swabs or the lint free cloth. Either Eco-
cleaning solution or Isopropyl Alcohol may be used in conjunction with the cleaning
utensil of choice..
2. Wipe the front of the wiper in a horizontal motion.
Page 3 of 9
3. Wipe the back of the wiper in a vertical motion.
** Clean around cap
Do not touch the Rubber Cap. Oil from your hands may prevent the cap from
sealing properly.
1. Using either a foam swab or a lint free cloth soaked in Eco-cleaning solution or Isopropyl
Alcohol, wipe around the edges of the rubber cap. This ensures a good seal is maintained
during head cleaning process.
Page 4 of 9
** Clean around Print Head
CAUTION
• When cleaning around Print Heads
Do Not Touch the Bottom of the heads.
Do Not Clean the Nozzle Surface with the cleaning device.
Do not use water to clean the head. Nozzle clogging may occur
Do Not Re-use dirty foam swabs or lint free cloths
1. Using a foam swab or lint free cloth clean the following areas under the carriage.
• Stainless steel ring around the head
• Space between the print head and the guide ramps
• Bottom sides of the guide ramps
• Any other areas under the print head carriage that appears to have ink or dirt build-up.
Page 5 of 9
2. To clean behind the print head, position the foam swab parallel to the pressure roller and
slide the swab behind the carriage. To clean either move the swab in a horizontal motion
or move the carriage back and forth.
Page 6 of 9
3. Clean the front of the head in a horizontal motion.
Page 7 of 9
4. To clean the area between the head an the guide ramps, position the carriage such that it
is just off the right side of the platen. Work the swab under the head, being especially
careful not to touch the nozzle surface area.
Guide RampPrint Head
Clean the space between the
head and the guide ramps
Page 8 of 9
/