Equinox Systems Swing Batten User manual

Equinox Systems
Brand
Equinox Systems
Model
Swing Batten
Category
Stroboscopes & disco lights
Type
User manual

This manual is also suitable for

Order code: EQLED033
Swing Batten
User Manual
www.prolight.co.uk Swing Batten User Manual
2
Safety advice
WARNING
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CARE-
FULLY BEFORE YOUR INITIAL START-UP!
• Beforeyourinitialstart-up,pleasemakesurethatthereisnodamagecausedduringtransportation.
• Shouldtherebeanydamage,consultyourdealeranddonotusetheequipment.
• Tomaintaintheequipmentingoodworkingconditionandtoensuresafeoperation,itisnecessary
fortheusertofollowthesafetyinstructionsandwarningnoteswritteninthismanual.
• Pleasenotethatdamagescausedbyusermodicationstothisequipmentarenotsubjecttowarranty.
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance
of this manual or any unauthorised modication to the equipment.
OPERATING DETERMINATIONS
Ifthisequipmentisoperatedinanyotherway,thanthosedescribedinthismanual,theproductmaysufferdamageand
thewarrantybecomesvoid.Incorrectoperationmayleadtodangere.g:short-circuit,burnsandelectricshocksetc.
Donotendangeryourownsafetyandthesafetyofothers!
Incorrectinstallationorusecancauseseriousdamagetopeopleand/orproperty.
CAUTION!
KEEP THIS EQUIPMENT
AWAY FROM RAIN,
MOISTURE AND LIQUIDS
CAUTION!
TAKE CARE USING
THIS EQUIPMENT!
HIGH VOLTAGE-RISK
OF ELECTRIC SHOCK!!
• Neverletthepowercablecomeintocontactwithother
cables.Handlethepowercableandallmainsvoltage
connectionswithparticularcaution!
• Neverremovewarningorinformativelabelsfromtheunit.
• Donotopentheequipmentanddonotmodifytheunit.
• Donotconnectthisequipmenttoadimmerpack.
• Donotswitchtheequipmentonandoffinshortintervals,
asthiswillreducethesystem’slife.
• Onlyusetheequipmentindoors.
• Donotexposetoammablesources,liquidsorgases.
• Alwaysdisconnectthepowerfromthemainswhen
equipmentisnotinuseorbeforecleaning!Onlyhandle
thepower-cablebytheplug.Neverpullouttheplugby
pullingthepower-cable.
• Makesurethattheavailablemainssupplyvoltageis
between100~240VAC,50/60Hz.
• Makesurethatthepowercableisnevercrimpedor
damaged.Checktheequipmentandthepowercable
periodically.
• Iftheequipmentisdroppedordamaged,disconnectthe
mainspowersupplyimmediatelyandhaveaqualied
engineerinspecttheequipmentbeforeoperatingagain.
• Iftheequipmenthasbeenexposedtodrastic
temperatureuctuation(e.g.aftertransportation),
donotconnectpowerorswitchitonimmediately.
Thearisingcondensationmightdamagetheequipment.
Leavetheequipmentswitchedoffuntilithasreached
roomtemperature.
• Ifyourproductfailstofunctioncorrectly,stopuse
immediately.Packtheunitsecurely(preferablyinthe
originalpackingmaterial),andreturnittoyourProLight
dealerforservice.
• Onlyusefusesofsametypeandrating.
• Repairs,servicingandpowerconnectionmustonlybe
carriedoutbyaqualiedtechnician.THISUNITCONTAINS
NOUSERSERVICEABLEPARTS.
• Thislightingxtureisforprofessionaluseonly-itis
notdesignedfororsuitableforhouseholduse.The
productmustbeinstalledbyaqualiedtechnicianin
accordancewithlocalterritoryregulations.Thesafetyof
theinstallationistheresponsibilityoftheinstaller.The
xturepresentsrisksofsevereinjuryordeathduetore
hazards,electricshockandfalls.
• Warning!RiskGroup2LEDproductaccordingto
EN62471.Donotviewthelightoutputwithoptical
instrumentsoranydevicethatmayconcentratethebeam.
• WARRANTY:Oneyearfromdateofpurchase.
www.prolight.co.uk Swing Batten User Manual
3
Product overview & technical specications
TheSwingBattenisadynamicmulti-beameffectdispensingeightintense,long-throwbeamsgeneratedbythe
10WCREEquad-colourLEDs.Thebattencutsthroughhazewitheaseproducingstunningbeameffects.The4
buttonmenusystemallowscontrolofmaster/slavefunctions,andthexturecanbealsobeoperatedinsound
activeandDMXmodes.
•8x10WCREEquad-colourLEDs(RGBW)
•Beamangle:4°
•16,100Lux@2m(perLED,fullon)
•IndividuallycontrollableLEDs
•Refreshrate:400Hz
•DMXchannels:6/12or16selectable
•Auto,soundactiveandmaster/slavemodes
•Tilt:220°
•0-100%dimmingandvariablestrobe
•Quickreleaseomegaclampsincluded
•4pushbuttonmenuwithLEDdisplay
•PowerCONinput/output
•3-PinXLRinput/output
•Convectioncooled
Swing Batten
Specications
Powerconsumption 100W
Powersupply 100~240V,50/60Hz
Fuse F3A250V
Dimensions 160x1065x80mm
Weight 7.5kg
Ordercode EQLED033
1065mm 80mm
160mm
www.prolight.co.uk Swing Batten User Manual
4
DMX INPUT DMX OUTPUT POWER INPUT:
100-240V~50/60Hz
POWER OUTPUT
ON
FUSE: F3A 250VOFF
www.prolight.co.uk
SWING
BATTEN
MENU UP DOWN ENTER
DMX INPUT DMX OUTPUT POWER INPUT:
100-240V~50/60Hz
POWER OUTPUT
ON
FUSE: F3A 250VOFF
www.prolight.co.uk
SWING
BATTEN
MENU UP DOWN ENTER
Technical specications
01-LCDdisplay
02-Menubutton
03-Upbutton
04-Downbutton
05-Enterbutton
06-3-pinDMXinput
07-3-pinDMXouput
08-PowerCONinput
09-PowerCONinput
10-On/offswitch
11-FuseF3A250V
12-Rubberfeet
13-Vents
14-Omegaclampmounts
15-Safetybondpoint
02
03
04
05
06
13 1314 14 14 1415
07 08 09 10 11
01
Inthebox:1 x xture,
1 x power cable,
1 x user manual &
2 x omega clamps
12 12
www.prolight.co.uk Swing Batten User Manual
5
Operating instructions
A d d r
A 0 0 1
A 5 1 2
C h N d
6 C h
1 6 C h
S h N d
S h 0
S h 8
S o U n
o n
o F F
S e n S
0
1 0 0
DMX address setting
Channel mode
Show mode 0-8
Slave 1
S L N d
S L 1
S L 2
Sound active mode
Sound sensitivity
L e d
o n
o F F
LED display on
LED display off
d s p I
I d s P
Display inversion
y e s
n o
t
I
L t
Tilt inversion
N a S t
Master mode
Slave 2
1 2 C h
r S e t
Reset
u e r
Firmware version
h o u r
Fixture hours
t e S t
Auto test
DMX mode:
OperatinginaDMXcontrolmodeenvironment
givestheuserthegreatestexibilitywhenit
comestocustomisingorcreatingashow.
Inthismodeyouwillbeabletocontrol
eachindividualtraitofthextureand
eachxtureindependently.
ToaccesstheDMXaddressmode,pressthe
“MENU”buttononthefrontoftheunittoshow
AddrontheLEDdisplay.Nowpressthe
“ENTER”buttonandusethe“UP”and“DOWN”
buttonstosettherequiredDMXaddress.
Pressthe“ENTER”buttontoconrmthesetting.
Toexitoutofanyoftheaboveoptions,
pressthe“MENU”button.
ToaccesstheDMXchannelmode,pressthe
“MENU”buttononthefrontoftheunittoshow
ChNdontheLEDdisplay.Nowpressthe
“ENTER”buttonandusethe“UP”and“DOWN”
buttonstochooseoneofthe6,12or16DMX
channelmodes.Pressthe“ENTER”buttonto
conrmthesetting.
Toexitoutofanyoftheaboveoptions,
pressthe“MENU”button.
www.prolight.co.uk Swing Batten User Manual
6
Operating instructions
6 channel mode:
Channel Value Function
CH1 000-255 Masterdimmer(0-100%)
CH2
000-007 Nofunction
008-255 Strobe(slow-fast)
CH3
000-007 Nofunction
008-049 Show1
050-091 Show2
092-133 Show3
134-175 Show4
176-217 Show5
218-247 Show6
248-255 Soundactive
CH4 000-255 Showmodespeed(slow-fast)
CH5
000-005 Nofunction
006-009 R
010-013 G
014-017 B
018-021 W
022-025 RG
026-029 RB
030-033 RW
034-037 GB
038-041 GW
042-045 BW
046-049 RGB
050-053 RGW
054-057 RBW
058-061 GBW
062-063 RGBW
064-079 Colourchase1
080-095 Colourchase2
096-111 Colourchase3
112-127 Colourchase4
128-143 Colourchase5
144-159 Colourchase6
160-175 Colourchase7
176-191 Colourchase8
192-207 Colourchase9
208-223 Colourchase10
224-239 Colourchase11
240-255 Colourchase12
CH6 000-255 Colourchasespeed(slow-fast)
12 channel mode:
Channel Value Function
CH1 000-255 Tilt(0°-270°)
CH2 000-255 Tiltmovementspeed
CH3 000-255 Masterdimmer(0-100%)
CH4
000-007 Nofunction
008-255 Strobe(slow-fast)
CH5
000-008 Nofunction
009-024 LED1-R
025-041 LED1-G
042-057 LED1-B
058-074 LED1-W
075-090 LED1-RG
091-107 LED1-RB
108-123 LED1-RW
124-140 LED1-GB
141-156 LED1-GW
157-173 LED1-BW
174-189 LED1-RGB
190-206 LED1-RGW
207-222 LED1-RBW
223-239 LED1-GBW
240-255 LED1-RGBW
CH6 - LED2(usevaluesfromCH5)
CH7 - LED3(usevaluesfromCH5)
CH8 - LED4(usevaluesfromCH5)
CH9 - LED5(usevaluesfromCH5)
CH10 - LED6(usevaluesfromCH5)
CH11 - LED7(usevaluesfromCH5)
CH12 - LED8(usevaluesfromCH5)
www.prolight.co.uk Swing Batten User Manual
7
Operating instructions
16 channel mode:
Channel Value Function
CH1 000-255 Tilt(0°-270°)
CH2 000-255 Tiltmovementspeed
CH3 000-255 Masterdimmer(0-100%)
CH4
000-007 Nofunction
008-255 Strobe(slow-fast)
CH5
000-008 Nofunction
009-024 LED1-R
025-041 LED1-G
042-057 LED1-B
058-074 LED1-W
075-090 LED1-RG
091-107 LED1-RB
108-123 LED1-RW
124-140 LED1-GB
141-156 LED1-GW
157-173 LED1-BW
174-189 LED1-RGB
190-206 LED1-RGW
207-222 LED1-RBW
223-239 LED1-GBW
240-255 LED1-RGBW
CH6 - LED2(usevaluesfromCH5)
CH7 - LED3(usevaluesfromCH5)
CH8 - LED4(usevaluesfromCH5)
CH9 - LED5(usevaluesfromCH5)
CH10 - LED6(usevaluesfromCH5)
CH11 - LED7(usevaluesfromCH5)
CH12 - LED8(usevaluesfromCH5)
CH13
000-007 Nofunction
008-049 Show1
050-091 Show2
092-133 Show3
134-175 Show4
176-217 Show5
218-247 Show6
248-255 Soundactive
CH14 000-255 Showmodespeed(slow-fast)
CH15
000-005 Nofunction
006-009 R
010-013 G
014-017 B
018-021 W
022-025 RG
026-029 RB
030-033 RW
034-037 GB
038-041 GW
042-045 BW
046-049 RGB
050-053 RGW
054-057 RBW
058-061 GBW
062-063 RGBW
064-079 Colourchase1
080-095 Colourchase2
096-111 Colourchase3
112-127 Colourchase4
128-143 Colourchase5
144-159 Colourchase6
160-175 Colourchase7
176-191 Colourchase8
192-207 Colourchase9
208-223 Colourchase10
224-239 Colourchase11
240-255 Colourchase12
CH16 000-255 Colourchasespeed(slow-fast)
www.prolight.co.uk Swing Batten User Manual
8
Operating instructions
Master/slave mode:
Tosetthemasterunit,pressthe“MENU”buttononthefrontofthemasterunittoshowSLNd onthe
LEDdisplay.Nowpressthe“ENTER”buttonandusethe“UP”and“DOWN”buttonstochooseNast.
Pressthe“ENTER”buttontoconrmthesetting.Thenselectyourdesiredprogram(soundactive,DMX
oroneofthebuilt-inprograms).
Tosettheotherunitsinslavemode,pressthe“MENU”buttononthefrontoftheunittoshowSLNd
ontheLEDdisplay.Nowpressthe“ENTER”buttonandusethe“UP”and“DOWN”buttonstochoose
eitherSL1(Slave1)orSL2(Slave2).Pressthe“ENTER”buttontoconrmthesetting.Theunitwill
nowruninsequencewiththemasterunit.
Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.
PleaseensurethatallslaveunitsaresettothesameDMXchannelmodeasthemasterunit.
Show mode (built-in programs):
Toaccesstheshowmodes,pressthe“MENU”buttononthefrontoftheunittoshowShNd
ontheLEDdisplay.Nowpressthe“ENTER”buttonandusethe“UP”and“DOWN”buttonstochoosethe
showyourequirefromSh 0~Sh 8.Pressthe“ENTER”buttontoconrmthesetting.
Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.
Sound active mode:
Toaccessthesoundactivemode,pressthe“MENU”buttononthefrontoftheunittoshowSoUn
ontheLEDdisplay.Nowpressthe“ENTER”buttonandusethe“UP”and“DOWN”buttonstosetthe
soundmodeonoroff.Pressthe“ENTER”buttontoconrmthesetting.
Toadjustthesoundsensitivity,pressthe“MENU”buttononthefrontoftheunittoshowSens
ontheLEDdisplay.Nowpressthe“ENTER”buttonandusethe“UP”and“DOWN”buttonstosetthe
soundsensitivity0~100.Pressthe“ENTER”buttontoconrmthesetting.
Value: 0 - 100 (0 = low sensitivity, 100 = high sensitivity)
Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.
www.prolight.co.uk Swing Batten User Manual
9
Setting the DMX address:
TheDMXmodeenablestheuseofauniversalDMXcontroller.Eachxturerequiresa“startaddress”
from1-512.Axturerequiringoneormorechannelsforcontrolbeginstoreadthedataonthechannel
indicatedbythestartaddress.Forexample,axturethatoccupiesoruses7channelsofDMXandwas
addressedtostartonDMXchannel100,wouldreaddatafromchannels:100,101,102,103,104,105
and106.Chooseastartaddresssothatthechannelsuseddonotoverlap.E.g.thenextunitinthe
chainstartsat107.
DMX 512:
DMX(DigitalMultiplex)isauniversalprotocolusedasaformofcommunicationbetweenintelligent
xturesandcontrollers.ADMXcontrollersendsDMXdatainstructionsformthecontrollertothexture.
DMXdataissentasserialdatathattravelsfromxturetoxtureviatheDATA“IN”andDATA“OUT”
XLRterminalslocatedonallDMXxtures(mostcontrollersonlyhaveadata“out”terminal).
DMX linking:
DMXisalanguageallowingallmakesandmodelsofdifferentmanufacturestobelinkedtogether
andoperatefromasinglecontroller,aslongasallxturesandthecontrollerareDMXcompliant.
ToensureproperDMXdatatransmission,whenusingseveralDMXxturestrytousetheshortest
cablepathpossible.TheorderinwhichxturesareconnectedinaDMXlinedoesnotinuencethe
DMXaddressing.Forexample;axtureassignedtoaDMXaddressof1maybeplacedanywherein
aDMXline,atthebeginning,attheend,oranywhereinthemiddle.Whenaxtureisassigneda
DMXaddressof1,theDMXcontrollerknowstosendDATAassignedtoaddress1tothatunit,
nomatterwhereitislocatedintheDMXchain.
DATA cable (DMX cable) requirements (for DMX operation):
ThisxturecanbecontrolledviaDMX-512protocol.TheDMXaddressissetonthebackoftheunit.
YourunitandyourDMXcontrollerrequireastandard3-pinXLRconnectorfordatainput/output,
seeimagebelow.
Also remember that DMX cable must be daisy chained and cannot be split.
FurtherDMXcablescanbe
purchasedfromallgoodsound
andlightingsuppliersor
ProLightConceptsdealers.
Pleasequote:
CABL10 – 2m
CABL11 – 5m
CABL12 – 10m
DMX setup
www.prolight.co.uk Swing Batten User Manual
10
Notice:
Besuretofollowthediagramsbelowwhenmakingyourowncables.Donotconnectthecables
shieldconductortothegroundlugorallowtheshieldconductortocomeincontactwiththeXLRs
outercasing.Groundingtheshieldcouldcauseashortcircuitanderraticbehaviour.
Special note:
Line termination:
Whenlongerrunsofcableareused,
youmayneedtouseaterminatoron
thelastunittoavoiderraticbehaviour.
Using a cable terminator will decrease
the possibilities of erratic behaviour.
(3-pin - Order ref: CABL9O, 5-pin - Order ref: CABL89)
5-pin XLR DMX connectors:
Somemanufacturesuse5-pinXLRconnectorsfordatatransmissioninplaceof3-pin.5-pinXLRxtures
maybeimplementedina3-pinXLRDMXline.Wheninsertingstandard5-pinXLRconnectorsintoa
3-pinlineacableadaptormustbeused.Thediagrambelowdetailsthecorrectcableconversion.
Terminationreducessignaltransmission
problemsandinterference.itisalways
advisabletoconnectaDMXterminal,
(resistance120Ohm1/4W)betweenpin2
(DMX-)andpin3(DMX+)ofthelastxture.
5-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
Pin 4: N/C
Pin 5: N/C
3-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
3-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
5-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
Pin 4: N/C
Pin 5: N/C
DMX setup
www.prolight.co.uk Swing Batten User Manual
11
WEEE notice
Correct Disposal of this Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries
with separate collection systems)
Thismarkingshownontheproductoritsliterature,indicatesthatitshouldnotbedisposedof
withotherhouseholdwastesattheendofitsworkinglife.Topreventpossibleharmtothe
environmentorhumanhealthfromuncontrolledwastedisposal,pleaseseparatethisfromother
typesofwastesandrecycleitresponsiblytopromotethesustainablereuseofmaterialresources.
Householdusersshouldcontacteithertheretailerwheretheypurchasedthisproduct,ortheir
localgovernmentofce,fordetailsofwhereandhowtheycantakethisitemforenvironmentally
saferecycling.
Businessusersshouldcontacttheirsupplierandcheckthetermsandconditionsofthe
purchasecontract.Thisproductshouldnotbemixedwithothercommercialwastesfordisposal.
www.prolight.co.uk Swing Batten User Manual
12
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Equinox Systems Swing Batten User manual

Equinox Systems
Brand
Equinox Systems
Model
Swing Batten
Category
Stroboscopes & disco lights
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents