Mellanox Technologies SX1018HP User manual

www.mellanox.com

SX1018HP Ethernet Managed Blade Switch

User Guide for HP c-Class BladeSystems

PNs: SX1018HP

Rev 1.0

Document Number: 4159

Rev 1.0

Mellanox Technologies

350 Oakmead Parkway Suite 100

Sunnyvale, CA 94085

U.S.A.

www.mellanox.com

Tel: (408) 970-3400

Fax: (408) 970-3403

Mellanox Technologies, Ltd.

Beit Mellanox

PO Box 586 Yokneam 20692

Israel

www.mellanox.com

Tel: +972 (0)74 723 7200

Fax: +972 (0)4 959 3245

Mellanox®, Mellanox logo, BridgeX®, ConnectX®, CORE-Direct®, InfiniBridge®, InfiniHost®, InfiniScale®,

MLNX-OS®, PhyX®, SwitchX®, UFM®, Virtual Protocol Interconnect® and Voltaire® are registered trademarks of

Mellanox Technologies, Ltd.

Connect-IB™, FabricIT™, Mellanox Open Ethernet™, MetroX™, MetroDX™, ScalableHPC™, Unbreakable-Link™ are

trademarks of Mellanox Technologies, Ltd.

All other trademarks are property of their respective owners.

NOTE:

THIS HARDWARE, SOFTWARE OR TEST SUITE PRODUCT (“PRODUCT(S)”) AND ITS RELATED

DOCUMENTATION ARE PROVIDED BY MELLANOX TECHNOLOGIES “AS-IS” WITH ALL FAULTS OF ANY

KIND AND SOLELY FOR THE PURPOSE OF AIDING THE CUSTOMER IN TESTING APPLICATIONS THAT USE

THE PRODUCTS IN DESIGNATED SOLUTIONS. THE CUSTOMER'S MANUFACTURING TEST ENVIRONMENT

HAS NOT MET THE STANDARDS SET BY MELLANOX TECHNOLOGIES TO FULLY QUALIFY THE

PRODUCTO(S) AND/OR THE SYSTEM USING IT. THEREFORE, MELLANOX TECHNOLOGIES CANNOT AND

DOES NOT GUARANTEE OR WARRANT THAT THE PRODUCTS WILL OPERATE WITH THE HIGHEST

QUALITY. ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED

WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT

ARE DISCLAIMED. IN NO EVENT SHALL MELLANOX BE LIABLE TO CUSTOMER OR ANY THIRD PARTIES

FOR ANY DIRECT, INDIRECT, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES OF ANY KIND

(INCLUDING, BUT NOT LIMITED TO, PAYMENT FOR PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;

LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY

THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE

OR OTHERWISE) ARISING IN ANY WAY FROM THE USE OF THE PRODUCT(S) AND RELATED

DOCUMENTATION EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

SX1018HP Ethernet Managed Blade Switch HW User Manual Rev 1.0

Mellanox Technologies

Table of Contents

Revision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Documentation Feedback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

HP contact information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Chapter 1 Preparing for Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

1.1 Audience. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

1.2 Kit contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

1.3 Mellanox SX1018HP Ethernet Switch Connector Bays . . . . . . . . . . . . . . . . 10

1.4 Mellanox SX1018HP Ethernet Switch LEDs. . . . . . . . . . . . . . . . . . . . . . . . . 12

Chapter 2 Hardware Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

2.1 Installing the Mellanox SX1018HP Ethernet Switch. . . . . . . . . . . . . . . . . . . 13

2.2 Installing and Removing Cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Chapter 3 Configuring the Switch the First Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Chapter 4 Removing the Mellanox SX1018HP Ethernet Switch for Service. . . . . . . . 22

Chapter 5 Regulatory Compliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

5.1 Regulatory Compliance Identification Numbers . . . . . . . . . . . . . . . . . . . . . . 23

5.2 Federal Communications Commission Notice. . . . . . . . . . . . . . . . . . . . . . . . 23

5.3 Modifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

5.4 Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

5.5 Canadian notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

5.6 European Union regulatory notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

5.7 Japanese class A notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

5.8 BSMI Notice. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

5.9 Korean class A notice. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

5.10 Chinese notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Rev 1.0

Mellanox Technologies

List of Figures

Figure 1: SX1018HP Ethernet Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Figure 2: HP BLade System Onboard Administrator . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Figure 3: QSFP Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Figure 4: Breakout or Fanout Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Figure 5: Port Splitting Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Figure 6: Switch LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Figure 7: Removing a Divider from the HP BladeSystem c7000 Enclosure Bay . . . . . 13

Figure 8: Install Blade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Figure 9: QSFP+ Cable Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Figure 10: Cable Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Figure 11: Cable Connected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Figure 12: Removing the Blade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Figure 13: For EU harmonized telecommunications products . . . . . . . . . . . . . . . . . . . . 24

Figure 14: For EU non-harmonized telecommunications products . . . . . . . . . . . . . . . . 24

SX1018HP Ethernet Managed Blade Switch HW User Manual Rev 1.0

Mellanox Technologies

List of Tables

Table 1 Document Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Table 2 Reference Documents and Web Sites. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Table 3 LED Assignments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Table 4 QSFP Cable Connector Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Table 5 Serial Terminal Program Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Table 6 Configuration Wizard Session - DHCP Configuration (Example) . . . . . . . . 17

Table 7 Configuration Wizard Session - Static IP Configuration . . . . . . . . . . . . . . . . 19

Table 8 Configuration Wizard Session - Zeroconf Configuration. . . . . . . . . . . . . . . . 20

Rev 1.0

Mellanox Technologies

Revision

Documentation Feedback

HP is committed to providing documentation that meets your needs. To help us improve the doc-

umentation, send any errors, suggestions, or comments to Documentation Feedback

(docsfeedback@hp.com).

Include the document title and part number, version number, or the URL when submitting your

feedback.

HP contact information

For United States and worldwide contact information, see the Contact HP website

(http://www.hp.com/ ).

In the United States:

• To contact HP by phone, call 1-800-334-5144. For continuous quality improvement,

calls may be recorded or monitored.

• It you have purchased a Care Pack (service upgrade), see the Support & Drivers website

(http://www8.hp.com/us/en/support-drivers.html). If the problem cannot be resolved at the web-

site, call 1-800-633-3600. For more information about Care Packs, see the HP website 

((http://www.hp.com/services/carepack).

Table 1 - Document Revision History

Date Revision Description of changes

April 2013 1.0 Initial release

SX1018HP Ethernet Managed Blade Switch HW User Manual Rev 1.0

Mellanox Technologies

About this Manual

This manual describes the installation and basic use of the Mellanox SX1018HP switch which is

based on the SwitchX-2 switch device.

Related Documentation

Additional Documentation available from Mellanox:

All of these documents can be found on the Mellanox Website. They are available either through

the product pages or through the support page with a login and password.

Conventions

Throughout this manual, the name and the term switch are used to describe the switch unless

explicitly indicated otherwise.

Table 2 - Reference Documents and Web Sites

Document Name Description

HP BladeSystem Technical

Resources

You can download the documentation for components referenced in this

installation guide from the HP Blade System Technical Resources web

site:

http://www.hp.com/go/bladesystem/documentation

Check the HP BladeSystem Technical Resources Website frequently for

updates.

HP BladeSystem Onboard

Administrator User Guide

http://www.hp.com/support/

BladeSystem_Onboard_Administrator_UG_en

Various HP BladeSystem

Onboard Administrator Manuals

http://www.hp.com/support/

BladeSystem_Onboard_Administrator_Manuals_en

HP BladeSystem Onboard

Administrator CLI User Manual

http://www.hp.com/support/

BladeSystem_Onboard_Administrator_CLI_UG_en

HP BladeSystem Onboard

Administrator - How to Make

"SHOW ALL" Inventory Report

http://www.hp.com/support/

BladeSystem_Onboard_Administrator_SHOW_ALL_Inv_Rpt_en

HP CLI Reference Manual

http://www.hp.com/support/MLNX-OS_CLI_SX1018HP_UG_en

HP MLNX-OS User Manual

http://www.hp.com/support/

MLNX_OS_EthernetManagedBladeSwitch_UG_en

HP SW release Notes for the

MLNX-OS software

http://www.hp.com/support/MLNX-OS_SX1018HP_RN_en

Rev 1.0

Mellanox Technologies

The following icons are used throughout this document to indicate information that is important

to the user.

This icon indicates information that is helpful to the user.

This icon indicates a situation that can potentially cause damage to hardware or soft-

ware.

BEWARE! This icon indicates a situation that can potentially cause personal injury or

damage to hardware or software.

This icon makes a recommendation.

SX1018HP Ethernet Managed Blade Switch HW User Manual Rev 1.0

Mellanox Technologies

1 Preparing for Installation

1.1 Audience

This document is intended for HP service representatives and other persons trained to install

hardware options in HP BladeSystem configurations. Such persons are expected to understand

the hazards of working in this environment and to take suitable precautions to minimize danger

to themselves and others.

1.2 Kit contents

The kit contains the following items:

• Mellanox SX1018HP Ethernet Switch for HP c-Class BladeSystems—689638-B21 (see Figure

• Warranty documentation

Figure 1: SX1018HP Ethernet Switch

Additional information

Mezzanine NIC installation determines interconnect bay assignments for switch installation. For

more information on the association between the mezzanine connector and the interconnect bays,

see the following documents under Mezzanine-to-Interconnect Mappings on the HP BladeSys

tem Technical Resources website:

• HP BladeSystem c7000 Enclosure Setup and Installation Guide:

http://www.hp.com/go/bladesystem/documentation

For specific port connections for each server blade, see the HP BladeSystem Onboard Adminis-

trator User Guide. Connections differ by server blade type. The information contained in this

document explains the cabling between the SX1018HP Ethernet Switch and the network

switches.

The HP Onboard Administrator screen example (see Figure 2) is a reference for port mapping.

This kit does not include cables. You must order the cables separately.

Your particular switch might look slightly different.

181716151413121110123456 789

UID

P L/A P L/A P L/A P L/A P L/A P L/A P L/A P L/A P L/A P L/A P L/A P L/A P L/A P L/A P L/APL/APL/APL/A

ellanox SX1018HP Ethernet Switch

Preparing for InstallationRev 1.0

Mellanox Technologies

Figure 2: HP BLade System Onboard Administrator

You can install up to 18 cables in the uplink ports on the SX1018HP Ethernet Switch.

1.3 Mellanox SX1018HP Ethernet Switch Connector Bays

Figure 3: QSFP Connectors

1.3.1 Uplink Ports

The ports labelled 1 to 18 are external uplink ports. You can install up to 18 40GbE QSFP+

cables or combinations of 40 GbE and 10GbE ports. The maximum number of 10GbE ports

available using this switch and breakout cables is 34.

1.3.2 Breakout Cables

Splitting the Data Stream Using Breakout (Fanout) Cables.

Specific ports can be split by using a QSFP 1X4 breakout cable to split one 40 GbE port into 4

lanes (4 SFP+ connectors 10GbE each). These 4 lanes then go, one lane to each of the 4 SFP+

connectors. Some ports can be split into 2 10 Gb/s ports, using lanes 1 and 2 only. When a QSFP

40GbE is supported in interconnect bays 3 to 8 only.

Your screen image might vary by switch type.

181716151413121110123456 789

UID

P L/A P L/A P L/A P L/A P L/A P L/A P L/A P L/A P L/A P L/A P L/A P L/A P L/A P L/A P L/APL/APL/APL/A

ellanox SX1018HP Ethernet Switch

SX1018HP Ethernet Managed Blade Switch HW User Manual Rev 1.0

Mellanox Technologies

port is split into 2 10Gb/s ports, then only SFP+ connectors #1 and #2 are used. Connectors #3

and #4 are left unconnected.

Figure 4: Breakout or Fanout Cable

Figure 5: Port Splitting Options

1.3.3 Mini USB

The mini USB in between uplink ports 9 and 10 is a debug port. This is for use by HP FAEs and

qualified service technicians only.

12 34 5 6 7 89 10 1112 1314 151617 18

This port is split-able into 4 10Gb/s SFP+ ports

This port is split-able into 2 10Gb/s SFP+ ports

This port is unmapped

Preparing for InstallationRev 1.0

Mellanox Technologies

1.4 Mellanox SX1018HP Ethernet Switch LEDs

Figure 6: Switch LEDs

The logical link activity LED flashes with greater frequency as network activity increases.

Table 3 - LED Assignments

Item Description Status

1 Unit ID LED Blue = Activated

Off = Deactivated

2 Internal health LED Green = Normal

Amber = Component degraded

Off = Power off

3 Physical Link LED Off = no link

Green = Physical link up

Blinking green = error detected.

4 Logical Link Activity

LED

Amber = no traffic

Blinking amber = traffic

123456

UID

P L/A P L/A P L/A P L/A P L/A P L/A

ellanox SX1018HP Ethernet Switch

SX1018HP Ethernet Managed Blade Switch HW User Manual Rev 1.0

Mellanox Technologies

2 Hardware Installation

This chapter contains the following sections:

• Installing the Mellanox SX1018HP Ethernet Switch

• Installing and removing cables in the Mellanox SX1018HP Ethernet Switch

2.1 Installing the Mellanox SX1018HP Ethernet Switch

2.1.1 Prepare the Interconnect Module Bay in the HP BladeSystem c7000 Enclosure

 To prepare the interconnect module bay in the HP BladeSystem c7000 enclosure, follow

these steps:

1. Remove any devices or blanks.

2. To remove the divider, press the divider release button and slide the divider out of the inter-

connect module bay (see Figure 7).

Figure 7: Removing a Divider from the HP BladeSystem c7000 Enclosure Bay

3. Press the divider release button.

4. Slide divider out from the interconnect module bay.

All panels and doors should be in place and securely fastened while the unit is in opera-

tion for proper cooling and for EMI emissions control.

Hardware InstallationRev 1.0

Mellanox Technologies

2.1.2 Install the Mellanox SX1018HP Ethernet Switch into the HP BladeSystem Enclo-

sure

 To install the Mellanox SX1018HP Ethernet Switch into the HP BladeSystem c7000 enclo-

sure, follow these steps:

1. Slide the Mellanox SX1018HP Ethernet Switch all the way into the HP BladeSystem c7000

enclosure (see

Figure 8).

2. Push the blade handle in until it is in the locked position (see Figure 8). The blade handle is

locked when you can not pull it back out without pushing the blade handle release.

Figure 8: Install Blade

2.2 Installing and Removing Cables

Figure 9 shows a cable with a QSFP+ connector used with the Mellanox SX1018HP Ethernet

Switch. QSFP+ connector to QSFP+ connector cables are used to connect multiple Mellanox

SX1018HP Ethernet Switches together. For example, you might connect two or more c-Class

interconnect modules together, for example, when another switch is installed in another HP Blad

eSystem c7000 enclosure that is mounted in the same rack. The Mellanox SX1018HP Ethernet

Switches are connected together by the QSFP+ to QSFP+ cables to form a high-performance net

work.

SX1018HP Ethernet Managed Blade Switch HW User Manual Rev 1.0

Mellanox Technologies

Figure 9: QSFP+ Cable Connector

2.2.1 Installing a Cable in the Mellanox SX1018HP Ethernet Switch

 To install a cable in the Mellanox SX1018HP Ethernet Switch, follow these steps:

1. Align the cable QSFP+ connector with the Mellanox SX1018HP Ethernet Switch port ( Fig-

ure 10).

2. Insert the QSFP+ connector into the Mellanox SX1018HP Ethernet Switch port (Figure 10)

until it is fully engaged and locked.

Figure 10: Cable Installation

Table 4 - QSFP Cable Connector Description

1 Cable

2 QSFP+ connector release pull tab

3 QSFP+ connector

The cables are not included in this kit and must be purchased separately.

1 QSFP+ connector

2 Mellanox SX1018HP Ethernet Switch - port # 1

3 Cable

72mm

max

18.35

Hardware InstallationRev 1.0

Mellanox Technologies

Figure 11: Cable Connected

You can install up to 18 cables in the Mellanox SX1018HP Ethernet Switch. It is not necessary to

install the cables in any particular order.

2.2.2 Removing a Cable from the Mellanox SX1018HP Ethernet Switch

To remove a cable from the Mellanox SX1018HP Ethernet Switch, pull the QSFP+ connector

release tab (

Figure 9) which releases the connector while using your other hand to remove the

connector from the switch port.

To completely remove the cable, it might be necessary to remove a releasable cable tie on the HP

c-Class blade cable management bracket.

If it is necessary to remove a releasable cable tie from the cable management bracket to fully

release a QSFP+ connector from the switch, reverse the installation procedure documented in the

cable management bracket installation guide.

1 Cable installed in port 1 of the Mellanox SX1018HP Ethernet Switch.

2 Mellanox SX1018HP Ethernet Switch.

SX1018HP Ethernet Managed Blade Switch HW User Manual Rev 1.0

Mellanox Technologies

3 Configuring the Switch the First Time

The procedures described in this chapter assume that you have already installed and powered-on

your switch according to the instructions in this document.

Step 1. If you are not already connected to the Onboard Administrator, connect to the Onboard Admin-

istrator of the Chassis using the serial port to your laptop. 

For more information see the http://www.hp.com/support/

BladeSystem_Onboard_Administrator_UG_en

Step 2. Connect to the HP Onboard Administrator and run “connect interconnect <slot number 1-7>”.

Step 3. Configure a serial terminal program (for example, HyperTerminal, minicom, or Tera Term) on

your host PC with the settings described in

Table 5.

Step 4. Login (from a serial terminal program) as admin and use admin as password. This starts the

Mellanox configuration wizard.

Step 5. Go through the Mellanox configuration wizard. Table 6 shows an example of a wizard session.

No remote IP connection is available at this stage.

Table 5 - Serial Terminal Program Configuration

Parameter Setting

Baud Rate 9600

Data bits 8

Stop bits 1

Parity None

Flow Control None

Table 6 - Configuration Wizard Session - DHCP (Sheet 1 of 2)Configuration (Example)

Wizard Session Display Comments

Mellanox configuration wizard

Do you want to use the wizard

for initial configuration? yes

You must perform this configuration the first time you

operate the switch or after resetting the switch. Type ‘y’

and then press <Enter>.

Step 1: Hostname? [switch] If you wish to accept the default hostname, then press

<Enter>. Otherwise, type a different hostname and press

<Enter>.

Configuring the Switch the First TimeRev 1.0

Mellanox Technologies

Step 2: Use DHCP on mgmt0

interface? [no] yes

Perform this step to obtain an IP address for the switch.

(mgmt0 is the management port of the switch.)

If you wish the DHCP server to assign the IP address,

type ‘yes’ and press <Enter>.

If you type ‘no’ (no DHCP), then you will be asked

whether you wish to use the ‘zeroconf’ configuration or

not.

If you enter ‘no’ (no Zeroconf), then you need to enter a

static IP, and the session will continue.

Step 3: Enable IPv6? [yes] The management interface will be able to use IPv6

addresses.

Step 4: Enable IPv6 auto-config

(SLAAC) on mgmt0 interface?

[no]

This turns on auto-configuration of the IPv6 addresses.

This is unsuitable for DHCPv6.

Step 5: Enable DHCPv6 on

mgmt0 interface? [no]

To enable DHCPv6 on the MGMT0 interface.

Step 6: Admin password (Press

<Enter> to leave unchanged)?

<new_password>

Step 6: Confirm admin pass-

word? <new_password>

To avoid illegal access to the machine, please type a pass-

word and then press <Enter>. Then confirm the password

by re-entering it.

Note that password characters are not printed.

You have entered the following

information:

<A summary of the configura-

tion is now displayed.>

To change an answer, enter the

step number to return to or hit

<enter> to save changes and exit.

Choice: <Enter>

Configuration changes saved.

The wizard displays a summary of your choices and then

asks you to confirm the choices or to re-edit them.

Either press <Enter> to save changes and exit, or enter the

configuration step number that you wish to return to.

Note:

To re-run the configuration wizard run the command

“configuration jump-start” in Config mode.

Table 6 - Configuration Wizard Session - DHCP (Sheet 2 of 2)Configuration (Example)

Wizard Session Display Comments

SX1018HP Ethernet Managed Blade Switch HW User Manual Rev 1.0

Mellanox Technologies

Table 7 - Configuration Wizard Session - Static IP Configuration

Wizard Session Display - Static IP Configuration (Example)

Mellanox configuration wizard

Do you want to use the wizard for initial configuration? yes

Step 1: Hostname? [switch]

Step 2: Use DHCP on mgmt0 interface? [yes] no

Step 3: Use zeroconf on mgmt0 interface? [no]

Step 4: Primary IP address? [for example 192.168.10.4] 10.10.10.10

Mask length may not be zero if address is not zero (interface eth0)

Step 5: Netmask? [0.0.0.0] 255.255.255.0

Step 6: Default gateway? [for example 192.168.10.1] 10.10.10.255

Step 7: Primary DNS server?

Step 8: Domain name?

Step 9: Enable IPv6? [yes]

Step 10: Enable IPv6 autoconfig (SLAAC) on mgmt0 interface? [no]

Step 11: Admin password (Enter to leave unchanged)?

To change an answer, enter the step number to return to.

Otherwise hit <enter> to save changes and exit.

Choice:

Configuration changes saved.

To return to the wizard from the CLI, enter the "configuration jump-start"

command from configure mode. Launching CLI...

switch>

Configuring the Switch the First TimeRev 1.0

Mellanox Technologies

Step 6. Before attempting a remote (for example, SSH) connection to the switch, check the mgmt0

interface configuration. Specifically, verify the existence of an IP address. To check the current

mgmt0 configuration, enter the following commands:

The following is an example of the output:

Table 8 - Configuration Wizard Session - Zeroconf Configuration

Wizard Session Display - IP Zeroconf Configuration (Example)

Mellanox configuration wizard

Do you want to use the wizard for initial configuration? yes

Step 1: Hostname? [switch]

Step 2: Use DHCP on mgmt0 interface? [yes] no

Step 3: Use zeroconf on mgmt0 interface? [no] yes

Step 4: Default gateway? [For example:192.168.10.1]

Step 5: Primary DNS server?

Step 6: Domain name?

Step 7: Enable IPv6? [yes]

Step 8: Enable IPv6 autoconfig (SLAAC) on mgmt0 interface? [no]

Step 9: Admin password (Enter to leave unchanged)?

To change an answer, enter the step number to return to.

Otherwise hit <enter> to save changes and exit.

Choice:

Configuration changes saved.

To return to the wizard from the CLI, enter the "configuration jump-start"

command from configure mode. Launching CLI...

switch>

switch > enable

switch # configure terminal

switch (config)# show interfaces mgmt0

Interface mgmt0 state

Admin up: yes

Link up: yes

IP address: 192.168.10.4

Netmask: 255.255.255.0

Speed: 1000Mb/s (auto)

Duplex: full (auto)

Interface type: ethernet

Page is loading ...

Mellanox Technologies SX1018HP, Mellanox SX1018 User manual

Related papers

Other documents