Airaid Intake System Installation guide

Brand
Airaid
Model
Intake System
Type
Installation guide

Airaid Intake System

A high-quality intake system designed to improve airflow efficiency in your vehicle. With its advanced filtration technology, it traps harmful contaminants while allowing maximum airflow for optimal engine performance. The system is crafted from durable materials to withstand the demands of off-road adventures, ensuring long-lasting reliability. By enhancing airflow, the Airaid Intake System unleashes the true power of your engine for increased responsiveness and acceleration.

Airaid Intake System

A high-quality intake system designed to improve airflow efficiency in your vehicle. With its advanced filtration technology, it traps harmful contaminants while allowing maximum airflow for optimal engine performance. The system is crafted from durable materials to withstand the demands of off-road adventures, ensuring long-lasting reliability. By enhancing airflow, the Airaid Intake System unleashes the true power of your engine for increased responsiveness and acceleration.

1
#311-110 INSTALLATION INSTRUCTIONS
1997-2002 Jeep TJ 2.5L &
1997-2004 Jeep TJ 4.0L (Does Not Fit 2.4L)
Thank you for purchasing the Airaid Intake System. Please read the instruction manual carefully before proceeding with the
installation. Contact Airaid @ (800) 498-6951 8:00 AM - 5:00 PM MST Weekdays for questions regarding fit or instructions that are
not clear to you. Your Airaid Intake System was carefully inspected and packaged. Check that no parts are missing, or were damaged
during shipping. If any parts are missing, contact Airaid. The air filter element is protected from direct exposure to water and debris;
care should be taken not to drive through deep water. WATER INGESTION IS THE DRIVERS RESPONSIBILTY!
Thank you for selecting Airaid.
Packing List:
701-421 Filter 3.5”x 9” Short Flange 1
KIT110S Splash Guard 1
KIT110TAC Tube Assembly 1
KIT110A Adapter Tube x1
KIT25C50HCSS Bolt ¼-20x1/2” x2
KIT110FB Long Bracket x1
KIT110RB Short Bracket x1
KIT09FWZ019 ¼” Washer x2
KIT110HPS Hardware Pack 1
KIT110T Nylon Wire Tie x1
KIT09FWZ019 ¼” Washer x8
KIT25C62HCSS Bolt ¼-20x5/8” x4
KIT25CNNES Nut ¼ -20 x4
Tools Required for this Installation:
Ratchet wrench
11 mm socket or wrench
10 mm socket or wrench
8 mm wrench
5/16” socket or nut driver
7/16” socket
7/16” wrench
Flat blade screwdriver
Pliers
I
nstallation Instructions. Read Me!
2
I DISCONNECT NEGATIVE (-) BATTERY CABLE.
II
Remove air filter housing.
a) Loosen intake tube hose clamp at the air box lid. Separate from lid. FIG #1
b) Unclip the air box lid. Remove and set aside the lid and filter.
c) From underneath the fender, use a 10mm ratchet to remove the 3 (three) nuts that secure the air box base.
*
Note: Unscrew the nuts from underneath and use an 8mm wrench to keep the top bolts from turning. FIG #2
III Assemble Airaid Tube
a) Bolt the two brackets to the Airaid tube using the shorter 1/4-20x1/2” bolts and washers. See FIG #3
Do not tighten yet.
b) The longer bracket attaches to the front mount point.
IV
Install Airaid Tube
a) Position tube in place of air box. See FIG #4
b) Locate and adjust Airaid brackets over the original air box mounting holes. Insert a 1/4-20x5/8” bolt
and flat washer. Into each mounting bracket.
c) On the opposite side, secure to the fender with a flat washer and nut.
V
Install “Splash Shield”
a) Locate and test fit the mounting points. Remove the existing plastic fastener for the inside mount.
See FIG #5 - Then fasten the shield with 1/4-20x5/8 bolts and washers.
b) Tie Wrap is optional. Press into hole on the top rear of splash shield. Fasten to radiator strut rod.
VI
Finishing up Airaid Installation.
a) Check for any foreign objects in the airflow path.
b) Reconnect battery cable. Double-check your work.
c) After one week of driving, check hardware and filter for tightness.
Figure # 1 Figure # 2
Figure # 3 Figure # 4
Figure # 5 Figure # 6
3
4
Synthamax Air Filters do not require oil. Service air filter as needed by
cleaning with common non-petroleum all-purpose household cleaner and
water. Simple Green®, Formula 409® or equivalent works great. Apply
cleaner to outside of air filter and allow to soak. Then flush filter clean
from the inside out with a garden hose and repeat steps if necessary. Do
not apply high pressure water or air to clean filter. Allow filter to air dry
and reinstall.
Rev: 10/25/10
Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050
(
800
)
498-6951 AiraidInfo
@
airaid.co
m
www.airaid.co
m
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Airaid Intake System Installation guide

Brand
Airaid
Model
Intake System
Type
Installation guide

Airaid Intake System

A high-quality intake system designed to improve airflow efficiency in your vehicle. With its advanced filtration technology, it traps harmful contaminants while allowing maximum airflow for optimal engine performance. The system is crafted from durable materials to withstand the demands of off-road adventures, ensuring long-lasting reliability. By enhancing airflow, the Airaid Intake System unleashes the true power of your engine for increased responsiveness and acceleration.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents