Bosch TES71525RW - VeroBar AromaPro 300 Owner's manual

de Gebrauchsanleitung

en Instruction manual

fr Mode d’emploi

it Istruzioni per l’uso

TES 712.. / TES 715..

Register your new Bosch now:

www.bosch-home.com/welcome

Page is loading ...

29

TES7.. | 08/2013

en

Safety instructions

Please read and follow the operating instructions carefully and

keep them for later reference. Enclose these instructions when

you give this appliance to someone else. This appliance is

designed for the preparation of normal household quantities in

the home, or in household-like, non-commercial environments.

Household-like environments include staff kitchens in shops,

of ces, agricultural and other small businesses or for use by

guests at bed-and-breakfast establishments, small hotels and

similar residential facilities.

¡ Danger of electric shock!

Connect and operate the appliance only according to the type plate

speci cations. To avoid potential hazards, repairs such as replacing

a damaged cable must only be carried out by our customer service

personnel.

This appliance may be used by children aged 8 years and older and

by persons with reduced physical, sensory or mental capabilities

or who lack experience and/or knowledge if they are supervised or

have been given instruction in the safe use of the appliance and

have understood the dangers involved. Keep children under 8 years

of age away from the appliance and connecting cable and do not

allow them to use the appliance. Children shall not play with the

appliance. Cleaning and user maintenance shall not be made by

children unless they are older than 8 years and supervised.

Never immerse the appliance or mains cable in water. Use only if

power cord and appliance show no signs of damage. Should a fault

occur, pull the plug or disconnect from the mains immediately.

30

Robert Bosch Hausgeräte GmbH

en

¡ Risk of suffocation!

Do not allow children to play with packaging material.

¡ Risk of scalding!

The milk frother 10 for milk / hot water

gets very hot. After use, allow to

cool down rst before touching.

¡ Risk of injury!

Do not reach into the grinding unit.

ONLY TES715

¡ Warning!

The cup warmer 27 gets very hot!

31

TES7.. | 08/2013

en

1 Power on/off switch O / I

2 Customising button á

3 Service programmes button à

4 Selection buttons < >

5 Display

a) Status line

b) Selection line

c) Navigation line

6 Rotary knob for display settings

7 Info menu button j

8 start button (drinks / programmes)

9 Coffee outlet,

height-adjustable and swivelling

10 Milk system,

height-adjustable and removable

(milk / hot water)

a) Upper part

b) Lower part

c) Suction hose

d) Suction pipe

11 Removable water tank

12 Lid for water tank

13 Storage compartments

(measuring spoon and milk frother

accessories)

14 Measuring spoon

(insertion aid for water lter)

15 Bean container

16 Aroma cover

17 Selector for grind setting

18 Powder compartment

(ground coffee / cleaning tablet)

19 Door to brewing unit

20 Brewing unit

a) Lock

b) Cover

21 Sliding button

22 Storage compartment for quick

reference guide

23 Drip tray

a) Panel

b) Grate

c) Coffee grounds container

24 Cable storage compartment

25 Rating label (ENo.; FD)

ONLY TES715

26 Milk container

27 Cup warming function

28 Button for cup warming function,

illuminated

Included in delivery

(Figure A on the fold-out pages)

1 Fully automatic espresso machine

TES712 / TES715

2 Instruction manual

3 Quick reference guide

4 Milk frother

5 Water hardness testing strip

6 Measuring spoon

ONLY TES715

7 Milk container

At a glance

(Figures B, C, D, E and F on the fold-out pages)

32

Robert Bosch Hausgeräte GmbH

en

Before using for the

rst time

General

Fill the water tank with pure, cold, uncar-

bonated water only and preferably use only

beans or coffee blends suitable for fully auto-

matic espresso and coffee machines. Do

not use coffee beans that have been glazed,

caramelised or treated with other additives

containing sugar, since they will block the

brewing unit.

The water hardness setting can be adjusted

on this appliance. The factory setting for the

water hardness

is 4. Check the hardness

of the water you use with the enclosed test

strip. If a value other than water hardness

4 is displayed, change the setting on the

appliance accordingly after switching on

(see “Menu settings – Water hardness”).

Setting up the appliance

● Place the fully automatic espresso machine

on a at, waterresistant surface that can

take its weight.

Important: Only use the appliance in frost-

free rooms

. If the appliance has been trans-

ported or stored at temperatures below

0 °C, wait at least 3 hours before operation.

● Pull out the mains plug from the cable

compartment 24 and plug it in. Adjust the

length of the cable by pushing it back in

and pulling it out. To do this, place the

appliance with its back ush with the edge

of the work surface and either pull the

cable downwards or push it upwards.

● Lift the lid of the water tank 12.

● Remove and rinse the water tank 11 and

ll it with fresh, cold water. Do not ll

above the “max” mark.

● Replace the water tank 11 and push it

rmly downwards into place.

● Close the water tank lid 12 again.

● Fill the bean container 15 with coffee

beans.

● Press the power switch 1 O / I. The

start button 8 lights up and the different

languages appear in the display 5.

The following languages can be selected:

TES7.. DE

Deutsch English

Français Italiano

TES7.. RW

English Русский

Nederlands Français

Italiano Svenska

Español Polski

Українська Magyar

Türkçe Dansk

Norsk Suomi

Português Čeština

Ελληνικa

● Use the buttons < and > 4 to select the

language in which you want the

display

texts to appear

.

The selected language is highlighted.

● Press the

start

button 8. The

language

you selected is saved.

● The brand logo lights up in the display 5.

The appliance now heats up and rinses.

Some water will run out of the coffee

outlet 9.

33

TES7.. | 08/2013

en

● The appliance is ready for use when the

symbols for the drink selection and the

start button 8 light up in the display 5.

Espresso

ËË

Í

Â Ã À Á Å Æ

Info: The factory settings of the fully auto-

matic espresso machine

are programmed for

optimal

performance. The appliance switches

off automatically after a specic time (see

“Menu settings – AutoOffafter”).

Note: If the appliance is being used for the

rst time, the

service programme has been

run

, or the appliance has not been oper-

ated for a long period, the rst beverage will

not have the full Aroma and should not be

consumed.

When the fully automatic espresso machine

is rst used, you will achieve a suitably thick

and stable “crema” only after the rst few

cups have been dispensed.

Controls

Power on/off switch O / I

The power on/off switch 1 O / I is used to

switch the appliance on or off. The appliance

rinses automatically when it is switched on

and off.

The appliance will not rinse if:

● it is still warm when switched on.

● there was no coffee drawn before

switching off.

The appliance is ready for use when the

symbols for the drink selection and the start

button 8 light up in the display 5.

Customising button á

The appliance provides the option of sav-

ing and calling up customised settings for

coffee drinks. Please refer to the section

“ Customising” for information on how to

save and call up these settings.

Service programmes button

à

Press the à button 3 briey to call up the

selection of service programmes. Please

run the programme as described in “Service

Programmes”.

Press and hold to activate or deactivate the

child-proof lock, see “Child-proof lock”.

Rotary knob

Turn the rotary knob 6 to the left or right to

navigate through the display 5, or to adjust

parameters in the menu.

Selection buttons < and >

Press the selection buttons 4 < and > to

navigate up and down through the menu

levels (navigation line 5c).

34

Robert Bosch Hausgeräte GmbH

en

Display

The display 5 uses symbols to indicate the

selection options, coffee strength and per-

cup quantity, and uses text to indicate set-

tings, ongoing processes and messages.

The rotary knob

6 and selection buttons

4 can be used to change settings

. The

selected setting is highlighted by a frame.

Espresso

ËË

Í

Â Ã À Á Å Æ

5a

5b

5c

Example:

The status line 5a shows the name of the

type of drink, along with the strength setting

55 and per-cup quantity

�

.

The selection line 5b shows symbols for

drink selection.

The arrows in the navigation line 5c indicate

the direction in which more menu levels can

be found.

Please refer to “Displays” for more detailed

information.

Start button

Press the start button 8 to begin drink

preparation or to start a service programme.

Press the start button 8 again during drink

preparation to stop the dispensing process

prematurely.

j button and settings

Use the j button 7 to display information

(press briey) and adjust settings (hold

down for at least 3 seconds).

Displaying information

The following information can be displayed

in the Info menu:

● when should the next service be

completed.

● how many drinks have been dispensed

since the espresso machine was

switched on.

● Press the j button 7 briey and navigate

with the < and > buttons 4.

Info

Descale after. 200

À

Clean after 200

À

Change filter in 200

À

*

Info

No. of coffees 11

No. of milk mixes 15

Amount hot water 2l

* appears only if the lter is activated.

Press the j button 7 briey to return to the

drink selection. If no button is pressed for

about 10 seconds, the appliance automati-

cally switches back to drink selection mode.

Adjusting settings

See “Menu settings”.

35

TES7.. | 08/2013

en

Adjusting the grinding unit

The rotary selector 17 adjusts the grind

settings from coarse to ne.

¡ Warning!

Adjust the grinding unit only while it is run-

ning! Otherwise the appliance may be dam-

aged. Do not reach into the grinding unit.

● While the grinding unit is running,

adjust the rotary selector 17 from

ne (a: Turn anticlockwise) to

coarse (b: Turn clockwise).

a b

Info: The new setting will not become

apparent until after the second cup of

coffee.

Note: If the message Please adjust

grinding unit to coarser setting!

appears in the display, the grind setting

for the coffee beans is too ne. Adjust the

grinding unit to a coarser setting.

Tip: For dark roast coffee beans, choose a

ner grind; for lighter beans a coarser grind.

ONLY TES715

Cup warming function

¡ Warning!

The cup warmer 27 gets very hot!

The fully automatic espresso machine has

a cup warmer 27 that can be switched on or

off manually with button 28. When the cup

warmer 27 is on, button 28 lights up.

Tip: For optimal cup warming, place the

base of the cups on the cup warmer 27.

Displays

Display messages

Various messages are shown in the

display 5.

Information (only TES715)

For example:

Espresso

ËË

Í

Water tank

almost empty

Prompts

For example:

Espresso

ËË

Í

Refill water tank

36

Robert Bosch Hausgeräte GmbH

en

Display settings

Press the selection buttons < and > 4 to

select the following selection menus in the

menu levels:

Drink selection

Espresso

Ë

Í

Â Ã À Á Å Æ

Coffee strength (only for coffee drinks)

Espresso

Ë

Í

5 55 555

Per-cup quantity

Espresso

Ë

Í

Î Ð Ò

Select your personal per-cup quantity

Espresso

Ë

Í

Î

± 0 ml

My coffee (only TES715)

My coffee

Ë

Í

Espresso Milk

40%

Turn the rotary knob 6 to adjust the

following parameters within the menus:

Settings – Drink selection:

Â

2xEspresso

Ã

2xCoffee

À

Espresso

Á

Coffee

Ä

Caffe Latte (only TES715)

Å

Macchiato

Æ

Cappuccino

Ç

My coffee (only TES715)

È

Milk froth

É

Warm milk

Ê

Hot water

Settings – Coffee strength:

å

Very mild

åå

Mild

ååå

Normal

ä

Strong

ã

Very strong

2x

å

AromaDouble Shot strong

2x

ååå

AromaDouble Shot strong +

2x

ã

AromaDouble Shot strong ++

AromaDouble Shot:

The longer the coffee is brewed, the

more bitter substances and undesired

Aromas are released. This has a nega-

tive effect on the taste and makes the

coffee less easily digestible. So for extra

strong coffee, the TES7.. has a special

AromaDouble Shot function. When half

the quantity has been prepared, coffee is

ground and brewed again so that only the

pleasant, Aromatic scents are released.

The AromaDouble Shot function can be

selected for all coffee drinks except for

EspressoÀ with a small per-cup quantity,

2 x Espresso Â and 2xCoffee

Ã

.

37

TES7.. | 08/2013

en

Settings – Per-cup quantity

�

small

Ð

medium

Ò

large

Settings – Personal per-cup quantity

The preset per-cup quantity

�

,

Ð

or

Ò

can

be individually adjusted to the size of the

cup in use by turning the rotary knob 6. The

per-cup quantity can be adjusted according

to the drink selected. An arrow in the

Ò

symbol in the top right-hand corner of

the display indicates whether the per-cup

quantity was increased or decreased. If you

set for example Coffee Á, the adjustment

of the per-cup quantity in ml, and in the

case of a milk-based coffee drink, for

example Cappuccino

Æ

, the adjustment of

the per-cup quantity including the volume of

milk (froth) in ml, is indicated.

Important: The selected amount in ml is

an approximate value and can vary sig-

nicantly as a result of crema forming, the

grind setting or the type of milk used, etc.

Settings – My coffee (only TES715)

In addition to selecting coffee strength and

per-cup quantity, you can choose the exact

mix of espresso and milk for your own coffee

setting Mycoffee Ç:

● The setting can be dened in 20 % steps

by turning the rotary knob 6.

Customising

You can store up to 6 user proles in the

User settings menu. The required coffee

and hot water temperatures are saved in

the user proles.

Important: The “Customising” settings

(á button 2) are not identical to those

under “Menu settings” (j button 7) and vice

versa.

Storing or changing the user

● Hold down the

á button 2 for at least

3 seconds.

The menu appears:

User settings

User 1



start

User 2

User 3

● Select the required user using the selec-

tion button and press the start button 8.

The following selection appears in the

display:

User settings: User 1

Edit name



start

Delete name

Coffee temp.

● To change the user name, use the selec-

tion button to go to Edit name



start

and press the start button 8.

The input eld appears in the display:

â ABCDEFGHIJKLMNOPQ

_ _____

Abort Store

● Turn the rotary knob 6 to select a letter or

number.

● Conrm by pressing the start button 8.

There are 6 characters available for the

user name.

To delete entries made, select the symbol

â and press the start button 8.

Note:

Press the selection button

> to save your

entry. Press the selection button < to cut

the process short.

Info: The entry can be overwritten at any

time.

38

Robert Bosch Hausgeräte GmbH

en

To delete the user, use the selection button

Delete name



start and press the start

button 8.

Saving temperatures

● Use the selection button to select Coffee

temp. or Hot water temp..

● Turn the rotary knob 6 to select the

required setting.

● Press the á button 2.

The settings are saved.

Calling up a user prole

● Press the

á button 2 briey.

The user prole menu appears:

Select a profile

Robert User 1 User 2

● Turn the rotary knob 6 to select a user

prole and press the start button 8.

The drink selection menu appears:

Macchiato

Ë

Í

Robert

À Á Å Æ

● Set the drink, coffee strength, etc. (see

“Display settings”).

● Dispense a drink (see “Preparation using

coffee beans”).

● The selected settings are saved.

● Press the á button 2 to exit the

customised menu.

Info: If you wish the appliance to exit the

menu automatically, you can set this as

described under “Menu settings – Exit

profile

”.

Child-proof lock

The appliance can be locked to protect

children from scalding and burning.

● Hold down the à button 3 for at least

3 seconds.

The display 5 shows a key; the child-proof

lock is activated.

Espresso

Ë

Í

It is no longer possible to operate the

appliance.

ONLY TES715

The cup warmer 27 is switched off.

● To deactivate the child-proof lock,

hold down the à button 3 for at least

3 seconds. The key disappears from

the display 5.

39

TES7.. | 08/2013

en

Menu settings

● Hold down the j button 7 for at least

3 seconds.

The different setting options are now

displayed.

Settings

Coffee temp.

Hot water temp. <85°C

Exit profile

The different setting options can be selected

with the selection buttons < and > 4.

Note: The changes you have made are

saved automatically. It is not necessary

to conrm them additionally. If no entry is

made after approx. 2 minutes, the menu will

close automatically.

The following settings can be selected:

Language

● Turn the rotary knob 6 to select the

required language.

Coffee temp.

● Turn the rotary knob 6 to set the coffee

temperature. The setting applies to all

types of preparation, except the custom-

ised settings under “Customising”.

Hot water temp.

● Turn the rotary knob 6 to set the tem-

perature. The setting applies to all types

of preparation except the customised

settings under “Customising”.

Exit profile

● Here you can set whether the appliance

should exit the customising function

automatically automatic or manually

manually.

Auto off after

● Turn the rotary knob 6 to enter the time

span after which the appliance should

automatically switch off following the last

drink preparation.

A time between 5 minutes and 8 hours can

be set.

Cup warm. off in (only TES715)

Here you can set the time span after which

the cup warmer 27 switches off again

automatically.

● Set the required time by turning the rotary

knob 6.

Contrast

The display 5 contrast can be set from –10

to +10. The factory setting is +0.

● Turn the rotary knob 6 to select the

required setting.

Water hardness

● Turn the rotary knob 6 to select the

required water hardness 1, 2, 3 or 4.

Info: It is important to set the water hard-

ness correctly, so that the appliance indi-

cates accurately when the descaling pro-

gramme should be run. The factory setting

for the water hardness is 4.

You can check the water hardness using

the enclosed test strip or by asking your

local water supplier.

● Dip the test strip briey in water and

check the result after one minute.

Level Water hardness

German (°dH) French (°fH)

1

2

3

4

1-7

8-14

15-21

22-30

1-13

14-25

26-38

39-54

40

Robert Bosch Hausgeräte GmbH

en

Water filter

A new water lter must be rinsed before it

can be used.

● To do this, press the water lter rmly

into the water tank 11 with the aid of the

measuring spoon 14. Fill the water tank

with water up to the “max” mark.

● Turn the rotary knob 6 to select start

and press the start button 8.

Place 1 l container

Place suction pipe in container



start

● Place a container with a capacity of 1 litre

under the milk frother 10.

● Place the end of the suction pipe 10d in

the container.

● Press the start button 8. Water will now

ow through the lter to rinse it.

● Next, empty the container.

The appliance is ready for use again.

Info: Rinsing the lter simultaneously

activates the setting for the “change lter”

display.

You can nd detailed information about the

water lter in the enclosed lter instructions.

The lter is no longer effective when the

Service - change filter display appears, or

at the latest after two months. It needs to be

replaced for reasons of hygiene and so that

there is no build-up of limescale (this could

damage the appliance).

Replacement lters can be obtained from

retailers (TCZ7003) or from customer

service (575491).

If no new lter is used, turn the

Water filter setting to no.

Info: If the appliance has not been used for

a prolonged period (for example, when you

are on vacation), the existing lter should

be rinsed before the appliance is used

again. To do this, simply dispense a cup of

hot water.

Transport. lock

● To avoid damage caused by frost during

transport and storage, the appliance must

be completely emptied rst.

Info: The appliance must be ready for use

and the water tank 11 lled.

● Press the start button 8. The appliance

automatically empties the pipe system

and switches off.

● Empty the water tank 11 and the drip

tray 23.

Factory reset

You can cancel your own settings and reset

the factory settings.

● To activate the factory settings, press the

start button 8.

Info: The appliance can also be reset to

the factory settings using a combination of

buttons. The appliance must be switched

off fully.

● Hold down the selection buttons < and >

4 and the on/off switch 1 O / I at the same

time for at least 5 seconds. Press the

start button 8. The factory settings are

now reactivated.

41

TES7.. | 08/2013

en

Preparation using

coffee beans

This fully automatic espresso machine

grinds beans freshly for each brew. If pos-

sible, use only beans for fully automatic

coffee and espresso machines. For optimal

quality, deep-freeze the beans or store in

a cool place in sealed containers. Coffee

beans can be ground while frozen.

Important: Fill the water tank 11 with cold,

fresh water every day. The water tank 11

should always contain sufcient water for

operating the appliance.

Tip (only TES715): Pre-warm cups,

especially

small, thick

espresso cups, on

the cup warmer 27.

Different coffee drinks can be prepared

quite simply at the press of a button.

Note: With some settings, the cof-

fee is prepared in two stages (see

“ AromaDouble Shot”). Wait until the proce-

dure is fully completed.

Drink preparation without milk

The appliance must be ready for use.

● Place the pre-warmed cup(s) under the

coffee outlet 9.

● Select the required 2 xEspresso Â,

2xCoffee

Ã

, Espresso À or CoffeeÁ

by turning the rotary knob 6.

The display 5 shows the selected drink

along with the setting for coffee strength

and per-cup quantity for this drink.

Espresso

Ë

Í

Â Ã À Á Å Æ

You can change the settings (see “Display

settings”) or call up and customise settings

(see “Customising”).

● Press the start button 8.

The coffee is brewed and then dispensed

into the cup(s).

Drink preparation with milk

The appliance must be ready for use.

● Place the suction pipe 10d of the milk

frother 10 deep in the milk container 26.

● Swivel the coffee outlet 9 to the right until

it clicks into place.

● Place the pre-warmed cup or glass under

the coffee outlet 9 and milk frother 10.

● Select the required Caffe Latte Ä (only

TES715), Macchiato

Å

, Cappuccino

Æ

or Mycoffee Ç (only TES715) by

turning the rotary knob 6.

The display 5 shows the selected drink

along with the setting for coffee strength

and per-cup quantity for this drink.

Cappuccino

Ë

Í

À Á Å Æ È É

You can change the settings (see “Display

settings”) or call up and customise settings

(see “Customising”).

● Press the start button 8.

First milk is delivered into the cup or glass.

Then the coffee is brewed and dispensed

into the cup or glass.

Important: Dried milk residue is difcult

to remove, so the milk frother 10 must be

cleaned with lukewarm water immediately

after use (see “Cleaning the milk system”).

42

Robert Bosch Hausgeräte GmbH

en

Preparation using

ground coffee

This fully automatic espresso machine can

also be operated using ground coffee (not

instant coffee powder).

Note: The AromaDouble Shot function

cannot be used when coffee is prepared

using ground coffee.

Drink preparation without milk

The appliance must be ready for use.

● Place the pre-warmed cup(s) under the

coffee outlet 9.

● Select the required Espresso À or

CoffeeÁ by turning the rotary knob 6.

● Open the powder compartment 18.

● Pour in no more than 2 level measuring

spoons 14 of ground coffee.

¡ Warning!

Do not use whole beans or instant coffee.

● Close the powder compartment 18.

● Press the start button 8.

The coffee is brewed and then dispensed

into the cup(s).

Note: Repeat the procedure for another cup

of coffee. If coffee is not dispensed within

90 seconds, the brewing chamber emp-

ties automatically to avoid an overow. The

appliance rinses.

Drink preparation with milk

The appliance must be ready for use.

● Place the suction pipe 10d of the milk

frother 10 deep in the milk container 26.

● Swivel the coffee outlet 9 to the right until

it clicks into place.

● Place the pre-warmed cup or glass under

the coffee outlet 9 and milk frother 10.

● Select the required Caffe Latte Ä (only

TES715), Macchiato

Å

, Cappuccino

Æ

or Mycoffee Ç (only TES715) by turn-

ing the rotary knob 6.

● Open the powder compartment 18.

● Pour in no more than 2 level measuring

spoons 14 of ground coffee.

¡ Warning!

Do not use whole beans or instant coffee.

● Close the powder compartment 18.

● Press the start button 8.

First milk is delivered into the cup or glass.

Then the coffee is brewed and dispensed

into the cup or glass.

Important: Dried milk residue is difcult

to remove, so the milk frother 10 must be

cleaned with lukewarm water immediately

after use (see “Cleaning the milk system”).

Note: Repeat the procedure for another

cup of coffee / milk drink. If coffee is not

dispensed within 90 seconds, the brewing

chamber empties automatically to avoid an

overow. The appliance rinses.

43

TES7.. | 08/2013

en

Preparing milk froth and

warm milk

¡ Risk of burns!

The milk frother 10 gets very hot. After use,

allow to cool down rst before touching.

The appliance must be ready for use.

● Place the suction pipe 10d of the milk

frother 10 deep in the milk container 26.

● Place the pre-warmed cup or glass under

the outlet of the milk frother 10.

● Select the required setting Milk froth

È

or Warmmilk

É

by turning the rotary

knob 6.

● Press the start button 8.

Milk froth or warm milk ows from the outlet

of the milk frother 10.

Press the start button 8 again to cut the

process short.

Info: When preparing warm milk, you may

hear a whistling sound. This is caused by

the milk frother 10 for technical reasons.

Tip: For optimal milk froth quality, use cold

milk with a fat content of at least 1.5 % if

possible.

Important: Dried milk residue is difcult

to remove, so the milk frother 10 must be

cleaned with lukewarm water immediately

after use (see “Cleaning the milk system”).

Dispensing hot water

¡ Risk of burns!

The milk frother 10 gets very hot. After use,

allow to cool down rst before touching.

The milk frother must be cleaned before

drawing hot water.

The appliance must be ready for use.

● Place the pre-warmed cup or glass under

the outlet of the milk frother 10.

● Select the required setting for Hot

water

Ê

by turning the rotary knob 6.

● Press the start button 8.

Please remove suction hose



start

● Remove the milk suction hose 10c and

press the start button 8.

Hot water runs out of the milk frother

outlet 10.

Press the start button 8 again to cut the

process short.

Note: It is possible to set the temperature of

the hot water (see “Menu settings”).

44

Robert Bosch Hausgeräte GmbH

en

Maintenance and

daily cleaning

¡ Danger of electric shock!

Unplug the appliance before cleaning it.

Never submerse the appliance in water.

Do not use a steam cleaner.

● Wipe the outside of the appliance with a

soft, damp cloth.

● Do not use any cleaning agents that

contain alcohol or spirits.

● Do not use abrasive cloths or cleaning

agents.

● Always remove any limescale, coffee,

milk, cleaning or descaling uid residue

immediately. Such residue can cause cor-

rosion. New sponge cloths may contain

salts. Salts can cause rust lm on stain-

less steel and must therefore be washed

out thoroughly before use.

● Pull the drip tray 23 with the coffee

grounds container 23c forwards and out.

Remove the panel 23a and grate 23b.

Empty and clean the drip tray and coffee

grounds container.

K

Do not put the following items in the

dishwasher: Panel of drip tray 23a,

powder compartment 18, brewing unit

20, water tank 11, Aroma cover 16 and

milk container cover (onlyTES715).

J

The following parts may be cleaned

in the dishwasher: Drip tray 23,

grate 23b, coffee grounds container

23c, measuring spoon 14 and milk

container (onlyTES715).

● Remove powder compartment 18 and

rinse under running water.

● Wipe out the inside of the tray holders.

Important: Drip tray 23 and coffee

grounds container 23c should be emptied

and cleaned daily to prevent mould from

developing.

Note: If the appliance is cold when

switched on, or if it is switched off after

dispensing coffee, it rinses automatically. In

other words, the system cleans itself.

Important: If the appliance has not been

used for a prolonged period of time (e. g.

after a vacation), clean the entire

appliance

thoroughly, including the milk system 10

and brewing unit 20.

45

TES7.. | 08/2013

en

Cleaning the milk system

Important: The milk system 10 must be

cleaned immediately after use!

The milk system 10 can be pre-cleaned

automatically (see “Service programmes” or

cleaned manually.

Dismantling the milk system 10 for cleaning:

● Pull the milk system 10 forward out of the

appliance.

● Turn the upper part 10a in an anti-

clockwise direction and remove from the

lower part 10b.

● Clean the individual parts with detergent

solution and a soft cloth.

● Rinse all parts with clean water and dry.

● Put all the parts back together. The milk

frother can then be clicked back into

place in the appliance.

Info: All parts of the milk frother 10 can also

be put in the dishwasher.

Cleaning the brewing unit (Fig. F)

(refer also to the quick reference guide)

In addition to the automatic cleaning

programme, the brewing unit 20 should be

removed regularly for cleaning.

● Switch the appliance off completely at the

power on/off switch 1 O / I ; no buttons

are lit.

● Slide the door opener to the right and

open the door 19 to the brewing unit.

● Slide the red lock 20a on the brewing unit

20 completely to the left.

● Press the red button 21, grasp the

brewing unit 20 by the recessed grips and

remove carefully.

● Remove the cover 20b of the brewing unit

and rinse the brewing unit 20 thoroughly

under running water.

46

Robert Bosch Hausgeräte GmbH

en

● Thoroughly clean the brewing unit sieve

under the running water.

Important: Clean the brewing unit with-

out detergent and do not put it in the

dishwasher.

● Wipe out the inside of the appliance

thoroughly with a damp cloth and remove

any coffee residues.

● Allow the brewing unit 20 and the inside

of the appliance to dry.

● Replace the cover 20b on the brewing

unit and reinsert the brewing unit 20 fully

into the appliance.

● Slide the red lock 20a fully to the right

and close the door 19.

Service Programmes

Tip: Refer also to the quick reference guide

in the storage compartment 22.

At regular intervals, the display 5 shows the

following texts:

Short rinse milk system or

Service - Descale or

Service - Clean or

Service - Calc‘nClean.

The appliance should be cleaned or descaled

immediately using the corresponding pro-

gramme. You have the option of combining

the processes Descaling and Cleaning

with the Calc‘nClean function (see

“ Calc‘nClean”). If the service programme is

not run as instructed, the appliance may be

damaged.

¡ Warning!

Follow the instructions for using the descal-

ing

and cleaning agents for each service

programme.

Never interrupt the service

programme!

Do not drink the liquids!

Never use vinegar, vinegar-based products,

citric acid or citric acid-based products!

Never put descaling tablets or other descal-

ing agents in the powder compartment 18!

Before starting the respective service

programme (descaling, cleaning or

Calc‘nClean), remove the brewing unit,

clean as instructed and replace.

47

TES7.. | 08/2013

en

Specially developed and suitable descal-

ing and cleaning tablets are available

from retailers or customer service.

Accessories Ordering number

Retail Customer

service

Cleaning

tablets

TCZ6001 310575

Descaling

tablets

TCZ6002 310967

Cleaning the milk system

Duration: approx. 1 minute

Cleaning and service

Short rinse

milk system



start

Calc‘nClean

The milk system 10 can be pre-cleaned

automatically.

● Press the à button 3.

Short rinse milk system



start

● Press the start button 8.

Place glass under frother, place

suction pipe in glass



start

● Place an empty glass under the milk

system 10 and put the end of the pipe

10d in the glass.

● Press the start button 8. The milk system

is cleaned automatically.

● Now empty the glass and clean the

suction pipe 10d.

In addition to this, clean the milk system

thoroughly at regular intervals (by hand or

in the dishwasher).

Descaling

Duration: approx. 30 minutes.

Cleaning and service

Descale



start

Clean

The

start

button 8 ashes while the different

descaling processes are running.

The gures on the top right indicate the

progress of the programme.

Important: If there is a water lter in the

water tank 11, it needs to be removed

before the service programme is run.

● Press the à button 3.

Descale



start

● Press the start button 8; the display 5 will

guide you through the programme.

Empty drip tray

Replace drip tray

● Empty the drip tray 23 and reinsert it.

Place 1 l container

Place suction pipe in container



start

● Place a container with 1 litre capacity

under

the milk frother 10.

● Place the end of the suction pipe 10d in

the container.

● Press the start button 8.

Remove filter



start

Info: If the water lter is activated, the

display will prompt you to remove the lter,

then press the start button 8 again.

Page is loading ...

Bosch TES71525RW - VeroBar AromaPro 300 Owner's manual

Bosch TES71525RW - VeroBar AromaPro 300 Owner's manual

in other languages

Related papers

Other documents