Tyan Tomcat i7221 S5150 User manual

Tomcat i7221 S5150 User’s Manual

i

http://www.tyan.com

Tomcat i7221

///

S5150

Revision 1.01

may be reproduced or translated without prior written consent from TYAN Computer Corp.

All registered and unregistered trademarks and company names contained in this manual are

property of their respective owners including, but not limited to the following.

TYAN, Tomcat, i7221 and S5150 are trademarks of TYAN Computer Corporation.

Intel Prescott and combinations thereof are trademarks of Intel Corporation.

Promise is a trademark of Promise Technology, Inc.

Award, AwardBIOS are trademarks of Award Software Incorporated.

Microsoft and Windows are trademarks of Microsoft Corporation.

IBM, PC, AT and PS/2 are trademarks of IBM Corporation.

Winbond is a trademark of Winbond Electronics Corporation.

SMSC is a trademark of Standard Microsystems Corporation.

Broadcom is a trademark of Broadcom Corporation.

Portable Document Format (PDF) is a trademark of Adobe Corporation.

Information contained in this document is furnished by TYAN Computer Corporation and has

been reviewed for accuracy and reliability prior to printing. TYAN assumes no liability

whatsoever, and disclaims any express or implied warranty, relating to sale and/or use of

TYAN products including liability or warranties relating to fitness for a particular purpose or

merchantability. TYAN retains the right to make changes to product descriptions and/or

specifications at any time, without notice. In no event will TYAN be held liable for any direct or

indirect, incidental or consequential damage, loss of use, loss of data or other malady resulting

from errors or inaccuracies of information contained in this document.

Tomcat i7221 S5150 Table of Contents

ii

http://www.tyan.com

Table of Contents

Before you begin… ..................................................................................................................v

Chapter 1: Introduction............................................................................................................1

1.1 Congratulations!............................................................................................................1

1.2 Hardware Specifications ............................................................................................... 1

Chapter 2: Board Installation..................................................................................................1

2.1 Installing the Motherboard ............................................................................................ 1

2.1.1 Installation Notes ................................................................................................ 1

2.2 Board Image .................................................................................................................2

2.3 Block Diagram...............................................................................................................3

2.4 Motherboard Components ............................................................................................ 4

2.5 Jumpers and Connectors.............................................................................................. 5

2.5.1 Serial Port: COM2 (J5) ....................................................................................... 6

2.5.2 SO-DIMM Socket: J10 ........................................................................................ 6

2.5.3 Serial ATA RAID Connectors: J19/J20/J21/J22 (SATA1 / SATA3 / SATA2 /

SATA4) ........................................................................................................................ 7

2.5.4 LAN2/LAN1 Disabled Headers: JP1/JP2............................................................ 7

2.5.5 Front Panel LAN1/LAN2 Link and Active LED Connector: JP3/JP6................... 8

2.5.6 Chassis Fan Connector: JP4 .............................................................................. 8

2.5.7 Front Panel LAN1/LAN2 Speed LED Pin-Header: JP5/JP7 ............................... 9

2.5.8 CPU Fan Connector: JP9 (P1FAN) .................................................................... 9

2.5.9 Front Panel USB 2.0 Connector: JP11/JP12.................................................... 10

2.5.10 Clear CMOS Jumper: JP13 ............................................................................ 10

2.5.11 Front Panel System Connector: JP14 ............................................................ 11

2.5.12 Front Fan Connector: JP15/JP17/JP21 (FAN2/FAN6/FAN4) ......................... 11

2.5.13 Chassis Fan Connector: JP16 (FAN1) ........................................................... 12

2.5.14 SMDC Connector: JP19 (Optional)................................................................. 12

2.5.15 PCI-X Speed Select Header: JP20................................................................. 13

2.5.16 SMDC/ASF2.0 Select Header:JP22/JP23 ...................................................... 13

2.6 Mounting the Motherboard.......................................................................................... 14

2.7 Installing Memory........................................................................................................ 15

2.7.1 Memory Installation Procedure ......................................................................... 16

2.8 Installing the Processor and Cooling Fan ................................................................... 16

2.9 Installing Drive Cables ................................................................................................ 19

2.10 Installing Expansion Cards ....................................................................................... 20

2.11 Connecting External Devices.................................................................................... 21

2.11.1 Onboard LAN LED Color Definition ................................................................ 21

2.12 Installing the Power Supply....................................................................................... 22

2.13 Finishing Up .............................................................................................................. 22

Chapter 3: BIOS Setup.............................................................................................................1

3.1 About the BIOS ............................................................................................................. 1

3.1.1 Starting Setup ..................................................................................................... 1

3.1.2 Setup Basics....................................................................................................... 1

3.1.3 Getting Help........................................................................................................ 1

3.1.4 In Case of Problems ........................................................................................... 2

3.1.5 Setup Variations ................................................................................................. 2

3.2 Main BIOS Setup .......................................................................................................... 2

3.3 Standard CMOS Features ............................................................................................ 4

3.4 Advanced BIOS Features ............................................................................................. 5

3.4.1 CPU Features ..................................................................................................... 7

3.4.2 Boot Sequence ................................................................................................. 10

3.4.3 Console Redirection ......................................................................................... 12

3.5 Advanced Chipsets Features...................................................................................... 12

Tomcat i7221 S5150 Table of Contents

iii

http://www.tyan.com

3.5.1 PCI Express Root Port Function....................................................................... 14

3.6 Integrated Peripherals................................................................................................. 16

3.6.1 OnChip IDE Device........................................................................................... 16

3.6.2 Onboard Device................................................................................................ 18

3.6.3 Super IO Device................................................................................................ 19

3.7 Power Management Setup ......................................................................................... 21

3.7.1 PCI Express PM Function................................................................................. 23

3.7.2 Power On Setup................................................................................................ 24

3.7.3 Reload Global Timer Events............................................................................. 25

3.8 PnP/PCI Configurations .............................................................................................. 26

3.8.1 IRQ Resources ................................................................................................. 27

3.9 PC Health Status ........................................................................................................ 28

3.10 Frequency/Voltage Control ....................................................................................... 28

3.11 Load Fail-Safe Defaults ............................................................................................ 30

3.12 Load Optimized Defaults........................................................................................... 30

3.13 Supervisor/User Password Setting ........................................................................... 31

3.14 Save & Exit Setup ..................................................................................................... 32

3.15 Exit Without Saving................................................................................................... 32

Chapter 4: SATA/RAID Setup (for SATA RAID model) ......................................................... 1

4.1 Configuring BIOS for Intel RAID for Serial ATA on board............................................. 1

4.1.1 Creating, Deleting, and Resetting RAID Sets ..................................................... 1

4.1.2 Create RAID 0 or RAID 1 Volume ...................................................................... 1

4.1.3 Delete RAID Volume........................................................................................... 2

4.1.4 Reset RAID Data ................................................................................................ 2

4.2 Loading the Intel Application Accelerator RAID Edition Driver During Operating

System Install...................................................................................................................... 2

4.2.1 Instructions on Creating F6 Floppy Diskette....................................................... 3

4.2.2 Installation Using F6 Method .............................................................................. 3

4.3 Intel RAID Option ROM................................................................................................. 4

4.3.1 Description.......................................................................................................... 4

4.3.2 Confirming Version of Intel RAID Option ROM Installed .................................... 4

4.3.3 Using the Intel RAID Option ROM ...................................................................... 4

4.4 Installing the Intel Application Accelerator RAID Edition............................................. 10

4.4.1 Installation Caution ........................................................................................... 10

4.4.2 Steps to Take Before Installing the Intel Application Accelerator RAID Edition 10

4.4.3 Obtaining and Installing the Intel Application Accelerator RAID Edition ........... 10

4.5 Confirming the Intel Application Accelerator RAID Edition is Installed ....................... 14

4.6 Confirming Version of Intel Application Accelerator RAID Edition Installed................ 14

4.6.1 Using the Intel Application Accelerator RAID Edition Utility:............................. 15

4.6.2 RAID Driver File Properties: ............................................................................. 15

4.7 Issues During Installation............................................................................................ 15

4.7.1 Symptom: Incompatible Hardware.................................................................... 15

4.7.2 Symptom: Unable to launch Intel(R ) Application Accelerator Readme file...... 15

4.8 “RAID Ready”.............................................................................................................. 16

4.8.1 “RAID Ready” Definition ................................................................................... 16

4.8.2 “RAID Ready” System Requirements ............................................................... 16

4.8.3 Steps on Setting Up a “RAID Ready” System .................................................. 16

4.8.4 Converting a “RAID Ready” System into RAID 0 or RAID 1 System with

Migration Feature....................................................................................................... 16

4.9 RAID Migration Instructions ........................................................................................ 17

4.9.1 Create RAID Volume from Existing Hard Drive ................................................ 18

4.9.2 Migration Process May Take Considerable Time to Complete......................... 21

4.10 Uninstalling the Intel Application Accelerator RAID Edition ...................................... 22

4.10.1 Uninstall Warning............................................................................................ 22

Tomcat i7221 S5150 Table of Contents

iv

http://www.tyan.com

4.10.2 Windows* 2003 / Windows 2000 .................................................................... 22

4.11 Unattended Installation Under Windows* 2003 / Windows 2000.............................. 23

4.12 Intel Storage Utility.................................................................................................... 23

4.12.1 Description...................................................................................................... 23

4.12.2 Create Volume Manually ................................................................................ 24

4.12.3 Successful Creation........................................................................................ 27

4.13 Configure BIOS for Adaptec RAID for Serial ATA on Board..................................... 27

4.13.1 BIOS Configuration......................................................................................... 27

4.13.2 Installing Serial ATA (SATA) hard disks ......................................................... 28

4.13.3 Adaptec RAID Configuration Utility................................................................. 28

4.13.4 Manage Array ................................................................................................. 29

4.13.5 Create Array ................................................................................................... 30

4.13. 6 Add/Delete Hotspare ..................................................................................... 32

4.13.7 Initialize Drives................................................................................................ 32

4.13.8 Disk Utilities .................................................................................................... 33

Chapter 5: Diagnostics............................................................................................................1

5.1 Beep Codes ..................................................................................................................1

5.2 Flash Utility.................................................................................................................... 1

Appendix I: Glossary ...............................................................................................................1

Appendix II: Post Error Code for BIOS ..................................................................................7

Technical Support..................................................................................................................12

Tomcat i7221 S5150 Before you begin…

v

http://www.tyan.com

Before you begin…

Check the package contents before you proceed.

The retail motherboard package should contain the following:

1 x Tomcat i7221 S5150 motherboard

1 x 34-Pin floppy drive cable

1 x Ultra-DMA-133/100/66/33 IDE cable

1 x Tomcat i7221 S5150 User’s Manual

1 x Tomcat i7221 S5150 Quick Reference Guide

1 x TYAN driver CD

1 x Intel 82801FR (ICH6R) Driver Diskette

1 x Adaptec Driver Diskette

1 x I/O shield

2 x Serial ATA power cable

4 x Serial ATA cable

1 x USB2.0 cable

If any of these items are missing, please contact your vendor or dealer for replacement before

continuing with the installation process.

Tomcat i7221 S5150 Chapter 1: Introduction

1-1

http://www.tyan.com

Chapter 1: Introduction

1.1 Congratulations!

Congratulations on your purchase of the TYAN Tomcat i7221 S5150, one of the most powerful

and versatile motherboard solutions available for Intel Prescott processors. Based on the

acclaimed Intel i7221 GMCH chipset, the S5150 offers exceptional performance and

outstanding features. With the x1 PCI Express slots, onboard two Gigabit Ethernet port, Serial

ATA RAID, four Dual-channel DDR DIMM sockets, plus the optional SCSI, four port and eight

port Serial ATA modules, the Tomcat i7221 S5150 is fast and flexible enough to fit your

server/workstation needs.

For more information about this and other TYAN products, visit the TYAN Web site at

http://www.tyan.com. Product FAQs, a list of distributors and advanced BIOS information are

also available on the Web site.

1.2 Hardware Specifications

Processors

y Single Socket-T (LGA775 socket)

y Intel



“Prescott” processor with EM64T

support

y 800/533MHz FSB support

Expansion Slots

y PCI-X 64-bit 133/100/66MHz bus supports

with

― One PCI-X slot (maximum of 100MHz

w/ riser card application)

― One proprietary 200-pin SO-DIMM

connector

y Two x1 PCI Express connectors

y One 32-bit, 33MHz PCI v2.3 slots

y Five total usable expansion slots/connectors

Chipset

y Intel E7221 GMCH

y Intel ICH6R South Bridge

y Intel PXH-V I/O bridge

y SMSC DME1737 Super I/O

System Management

y SMSC DME1737 w/ hardware monitoring

y One 3+1-pin CPU Fan header w/

tachometer input and temperature-sensing

auto fan control

y Four 3-pin system Fan headers (two w/

tachometer input and temperature-sensing

auto fan control)

y Temperature and voltage monitoring

y Watchdog timer

y Port 80 code display LED

Integrated I/O Interface

y One floppy connector

y Four USB 2.0 ports (via cable)

y One COM2 port (via cable)

y One LPT port (via cable)

y Power/IDE/SATA LED connectors

y Two 2+2-pin headers for front panel

LAN LED

y TYAN 2 x 9 front-panel pin header

Integrated LAN Controllers

y Two GbE LAN controllers

― Two Broadcom BCM5721 PCI

Express GbE LAN controller

― Operating at x1 PCI-E interface

― ASF 2.0 support

― Pin headers for front panel LAN

LED

Optional modules

y M7901/M7902, SO-DIMM Ultra 320

SCSI card

― Adaptec AIC-7901/7902 single/dual-

channel Ultra 320 SCSI controller

― Adaptec HostRAID support w/RAID

0, 1, 10 supported

y M8110/M8120 SO-DIMM SATA card

― Adaptec AIC-8110/8120 SATA

controller

― Support up to 4-port (M8110) and 8-

port (M8120) SATA ports running at

1.5GB/s

― Adaptec HostRAID support with

RAID 0, 1, 10 supported

Tomcat i7221 S5150 Chapter 1: Introduction

1-2

http://www.tyan.com

Memory

y Dual memory channels

y Supports Up to four DDR-333/400 DIMM

y Up to 4GB of Non-Reg/ECC or Non-

Reg/Non-ECC memory

Intelligent PCI IDE (ICH6R)

y Single channel master mode supports two

IDE devices

y Support for ATA-100/66/33 IDE drives and

ATAPI compliant devices

Integrated Serial ATA (ICH6R)

y Four Serial ATA Host controllers embedded

y Support four Serial ports running at 1.5Gb/s

y RAID 0, 1 support

Integrated PCI Graphic

y 8-bit VGA DAC embedded the MCH to

support an analog display

Rear Panel I/O ports

y Stacked PS/2 Mouse & Keyboard ports

y Stacked two USB2.0 ports

y One 15-pin VGA port

y One 9-pin COM port

y Six audio jacks (optional)

y Two RJ45 10/100/1000 Base-T port w/

activity LED

BIOS

y Award BIOS 8Mbit Flash ROM

y Support APM 1.2 & ACPI 1.0B

y PnP, DNI 2.0, WFM 2.0 Power

Management

Power

y EPS12V support, on board 4-phase

VRM

y Universal 24-pin + 8-pin or 20-pin + 4-

pin power connectors

Form Factor

y ATX footprint

y 12” x 9.6” (305mm x 245mm)

Regulatory

y FCC Class B (Declaration of

Conformity)

y CE (Declaration of Conformity)

y BSMI

Note

TYAN reserves the right to add support or discontinue support for any OS

with or without notice.

Tomcat i7221 S5150 Chapter 2: Board Installation

2-1

http://www.tyan.com

Chapter 2: Board Installation

2.1 Installing the Motherboard

The Tomcat i7221 S5150 motherboard conforms fully to the ATX specification. Before

continuing with the installation, confirm that your chassis supports a standard ATX

motherboard. If you are unsure, contact your dealer for more information.

2.1.1 Installation Notes

This user manual contains important information and you should read it thoroughly before

attempting the installation procedure.

Precautions:

• Static electricity can damage components on your motherboard. Before touching the

product, discharge any static build up in yourself by touching a well grounded object

such as a metal water pipe or a grounded electrical appliance. TYAN recommends

putting on a good quality grounded wrist strap before removing your motherboard from

the antistatic bag.

• Disconnect your computer from the power supply before any disassembly procedure is

attempted.

• Touch the motherboard as little as possible and do not touch the bottom of the board at

• all. Bending or flexing the motherboard may break delicate components or copper tracks

on the board.

• Avoid touching any of the motherboard components.

• Place the motherboard on a grounded antistatic surface or on the antistatic bag in which

the board was shipped.

• Inspect the board for damage.

Read the following sections for detailed instructions on how to install your motherboard in a

chassis and add a processor, memory, and disk drives.

Warning

Do not apply power to the board if it appears damaged.

Tomcat i7221 S5150 Chapter 2: Board Installation

2-2

http://www.tyan.com

2.2 Board Image

The following is an image of the Tomcat i7221 S5150.

The above photograph is purely representative. Due to engineering updates and new

board revisions, certain components may change and or be repositioned. The picture

above may or may not look exactly like the board you received.

The following page includes details on the vital components of this motherboard.

Tomcat i7221 S5150 Chapter 2: Board Installation

2-3

http://www.tyan.com

2.3 Block Diagram

The following is a block diagram of the Tomcat i7221 S5150.

PRESCOTT

LGA775

CPU

VRM

Intel

E7221

GMCH

Intel

ICH6R

DIMM1

PXH-V

SUPER-I/O

DME1737

ATA 100 IDE X 1

800 MHz SYSTEM BUS

MD/MA

PCI

EXPRESS

DMI BUS

DIMM2

DIMM3

DIMM4

133MHz OR

100MHz PCI-X

133MHz OR

100MHz PCI-X

SATA X 4 PORT

USB 2.0 X 6 PORT

PRINTER

PORT

SERIAL

PORT

SERIAL

PORT

KBD

PORT

FLOPPY

CONN

BIOS

8Mb

10/100/1000

LAN B

BCM5721

RJ45

MD/MB

DDR 333/400

DDR B DIMMS

DDR 333/400

DDR A DIMMS

PCI1

LPC BUS

FIRMWARE HUB

SO DIMM

PCI-X

CLOCK

CHIP

PCI 32/33MHz

10/100/1000

LAN A

BCM5721

RJ45

PCI E1

PCI E2

VGA

CONNECTOR

PCI E-1 / PCI E-2

Tomcat i7221 S5150 Chapter 2: Board Installation

2-4

http://www.tyan.com

2.4 Motherboard Components

The diagram below shows the main motherboard components.

1

PW2

P1FAN

JP9

BIOS

JP17

Intel

E7221

Intel

ICH6R

PC I -E1

SATA2

SATA1

FDD J9

JP20

IDE J13

DIMM3

DIMM2

DIMM1

1

SMSC

I/O

BT1

DIMM4

PC I -E2

1

LED1

SATA3

SATA4

FAN6

BROADCOM

LAN

(Optional)

1

JP16

JP10

1

JP13

1

JP15

S5150

KB(Bottom)

Mouse(Top)

JP11

JP12

BROADCOM

LAN

(Optional)

JP6

1

JP3

1

SMDC JP19

1

JP4

J5

32-bit 33MHz (5V) PCI J11

SO_DIMM J10

64-bit 100MHz PCI-X J12

J4

US B 1

J1

KB / MS

J3

(COM1)

J2

(VGA)

LAN1

LAN2

LPT J8

Intel

PXH

JP7

1

JP5

1

JP2

1

JP1

1

JP21

1

JP22

1

JP23

This diagram represents the latest version of the motherboard available at the time of

publishing. The board you receive may or may not look exactly like the above diagram.

Parts are not drawn to scale.

Tomcat i7221 S5150 Chapter 2: Board Installation

2-5

http://www.tyan.com

2.5 Jumpers and Connectors

Jumpers and pin headers are provided on your motherboard for configuration and connection

to peripherals. The following section shows you how to set your jumpers and use your pin

headers.

Connector Function Ref. Page

J5 COM2 port Page 2-6

J8 Printer port connector

J9 Floppy disk drive connector

J10 SO-DIMM socket Page 2-6

J13 IDE connector

J19/J20/J21/J22 Serial ATA connectors Page 2-7

J23** Reserved

JP1/JP2 LAN2/LAN1 disabled headers Page 2-7

JP3/JP6

Front panel LAN1/LAN2 link/activity LED

connector

Page 2-8

JP4 (FAN1) Chassis fan connector Page 2-8

JP5/JP7 Front Panel LAN2/LAN1 speed LED headers Page 2-9

JP9 (P1FAN)

CPU fan connector with tachometer input and

fan speed control

Page 2-9

JP10** Reserved Page 2-9

JP11/JP12 Front panel USB connector Page 2-10

JP13 Clear CMOS jumper Page 2-10

JP14 Front panel system connector Page 2-11

JP15/JP17/JP21

Front fan connector with tachometer input and

fan speed control

Page 2-11

JP16 Chassis fan connector with fan speed control Page 2-12

JP19* SMDC connector (optional) Page 2-12

JP20 PCI-X speed select header Page 2-13

* Some jumpers and headers are optional and not available with the board due to the different

configurations.

** J23 and JP10 are reserved for OEM use only

.

Jumper Legend

Jumper OFF – open (without jumper cap)

Jumper ON – closed (with jumper cap)

Tomcat i7221 S5150 Chapter 2: Board Installation

2-6

http://www.tyan.com

2.5.1 Serial Port: COM2 (J5)

10 2

9 1

Signal Description

GND

(Ground)

DTR

(Data-Terminal-Ready)

TX

(Transfer-Data)

RX

(Receive-Data)

DCD

(Data Carrier Detect)

Pin#

9 7 6 3

1

Pin#

10 8 5 4

2

PW 2

P1 FA N

JP9

BIOS

JP1 7

Intel

E72 21

Intel

IC H 6R

PCI-E1

SATA2

SATA1

FDD J9

JP20

IDE J13

DIMM3

DIM M2

DIM M1

SMSC

I/O

BT1

DIMM4

PCI-E2

LED1

SATA 3

SA TA 4

FAN6

BROADCOM

LAN

(Optional)

JP 16

JP10

JP13

JP15

S5150

K B (B o tto m )

Mouse(Top)

JP11

JP12

BROADCOM

LAN

(O pt io n a l )

JP 6

JP 3

SMDC JP19

JP4

J5

32-bit 33MHz (5V) PCI J11

SO_DIMM J10

64-bit 100MHz PCI-X J12

J4

USB1

J1

KB / MS

J3

(COM1)

J2

(V G A )

LAN 1

LAN 2

LPT J8

Intel

PXH

JP 7

JP 5

JP 2

JP 1

JP21

JP22

JP23

Signal Description

NC/Key

RI

(Ring-Indicator)

CTS

(Clear-to-Send)

RTS

(Request-to- Send)

DSR

(Data-Set-Ready)

2.5.2 SO-DIMM Socket: J10

PW 2

P1 FAN

JP9

BIOS

JP17

Intel

E72 21

Intel

IC H 6R

PCI-E1

SATA2

SATA1

FDD J9

JP20

IDE J1 3

DIMM3

DIM M2

DIMM1

SMSC

I/O

BT1

DIMM4

PCI-E2

LED1

SA TA3

SATA4

FAN6

BROADCOM

LAN

(Optional)

JP16

JP10

JP13

JP15

S5150

KB(Bottom)

Mouse(Top)

JP11

JP12

BROADCOM

LAN

(O p ti o na l )

JP 6

JP 3

SMDC JP19

JP4

J5

32-bit 33MHz (5V) PCI J11

SO_DIMM J10

64-bit 100MHz PCI-X J12

J4

US B1

J1

KB / MS

J3

(COM1)

J2

(V G A)

LAN 1

LAN 2

LPT J8

Intel

PXH

JP 7

JP 5

JP 2

JP 1

JP21

JP22

JP23

Connect SCSI Daughter Card

Compatible with Tyan M7902

J5

J10

Tomcat i7221 S5150 Chapter 2: Board Installation

2-7

http://www.tyan.com

2.5.3 Serial ATA RAID Connectors: J19/J20/J21/J22 (SATA1 / SATA3 / SATA2 / SATA4)

7 GND

6 RXP

5 RXN

4 GND

3 TXN

2 TXP

7

1

1 GND

PW 2

P1FAN

JP9

BIOS

JP17

Intel

E72 21

Intel

ICH6R

PCI-E1

SATA2

SATA1

FDD J9

JP20

IDE J1 3

DIMM3

DIM M2

DIM M1

SMSC

I/O

BT1

DIMM4

PCI-E2

LED1

SATA3

SATA4

FAN6

BROADC OM

LAN

(Optional)

JP16

JP10

JP13

JP15

S5150

K B (B o tto m )

Mouse(Top)

JP11

JP 12

BROADCOM

LAN

(O p tio n a l )

JP 6

JP 3

SMDC JP19

JP4

J5

32-bit 33MHz (5V) PCI J11

S O_DIMM J10

64-bit 100MHz PCI-X J12

J4

US B1

J1

KB / MS

J3

(COM1)

J2

(V G A )

LAN 1

LAN 2

LPT J8

Intel

PXH

JP 7

JP 5

JP 2

JP 1

JP21

JP22

JP23

Connects to the Serial ATA ready drives

via the Serial ATA cable

Y

ou may use any two of the four Serial

A

TA ports to have the support of RAID 0

and 1 through the on board ICH6R south

bridge chip.

2.5.4 LAN2/LAN1 Disabled Headers: JP1/JP2

1

OPEN: Disabled

PW 2

P1 FA N

JP9

BIOS

JP17

Intel

E7 2 2 1

Intel

ICH6R

PCI-E1

SATA2

SATA1

FDD J9

JP20

IDE J1 3

DIMM3

DIM M2

DIM M1

SMSC

I/O

BT1

DIMM4

PCI-E2

LED1

SATA3

SATA4

FAN6

BROADCOM

LAN

(Optional)

JP16

JP10

JP13

JP15

S5150

K B (B o tto m )

Mouse(Top)

JP11

JP 12

BROADCOM

LAN

(O p ti o na l )

JP 6

JP 3

SMDC JP19

JP4

J5

32-bit 33MHz (5V) PCI J11

S O_DIMM J10

64-bit 100MHz PCI-X J12

J4

US B1

J1

KB / MS

J3

(COM1)

J2

(V G A)

LAN 1

LAN 2

LPT J8

Intel

PXH

JP 7

JP 5

JP 2

JP 1

JP21

JP22

JP23

1

CLOSED: Enabled (Default)

SATA

JP2

JP1

Tomcat i7221 S5150 Chapter 2: Board Installation

2-8

http://www.tyan.com

2.5.5 Front Panel LAN1/LAN2 Link and Active LED Connector: JP3/JP6

JP3

1

Pin 1: LED+

Pin 2: LED-

JP6

1

Pin 1: LED+

Pin 2: LED-

PW 2

P1FAN

JP9

BIOS

JP17

Intel

E7 2 21

Intel

ICH6R

PCI-E1

SATA2

SATA1

FDD J9

JP20

IDE J1 3

DIMM3

DIM M2

DIM M1

SMSC

I/O

BT1

DIMM4

PCI-E2

LED1

SA T A3

SATA4

FAN6

BROADCOM

LAN

(Optional)

JP 16

JP10

JP13

JP15

S5150

K B (B o tto m )

Mouse(Top)

JP11

JP12

BROADCOM

LAN

(O p t i o n a l )

JP 6

JP 3

SMDC JP19

JP4

J5

32-bi t 33MHz (5V) PCI J11

S O_DIMM J10

64-bit 10 0MHz PCI-X J12

J4

USB1

J1

KB / MS

J3

(COM1)

J2

(V G A )

LAN 1

LAN 2

LPT J8

Intel

PXH

JP 7

JP5

JP 2

JP 1

JP21

JP22

JP23

Use these headers to connect with the

front panel link/activity LEDs for LAN1 and

LAN2.

2.5.6 Chassis Fan Connector: JP4

+12V

GND

NC

PW 2

P1 FA N

JP9

BIOS

JP1 7

Intel

E72 21

Intel

IC H 6R

PCI-E1

SATA2

SATA1

FDD J9

JP20

IDE J13

DIMM3

DIM M2

DIM M1

SMSC

I/O

BT1

DIMM4

PCI-E2

LED1

SATA 3

SA TA 4

FAN6

BROADCOM

LAN

(Optional)

JP 16

JP10

JP13

JP15

S5150

K B (B o tto m )

Mouse(Top)

JP11

JP12

BROADCOM

LAN

(O pt io n a l )

JP 6

JP 3

SMDC JP19

JP4

J5

32-bit 33MHz (5V) PCI J11

SO_DIMM J10

64-bit 100MHz PCI-X J12

J4

USB1

J1

KB / MS

J3

(COM1)

J2

(V G A )

LAN 1

LAN 2

LPT J8

Intel

PXH

JP 7

JP 5

JP 2

JP 1

JP21

JP22

JP23

Use this header to connect the chassis

cooling fan to your motherboard to keep

the system stable and reliable.

JP3

JP6

JP4

Tomcat i7221 S5150 Chapter 2: Board Installation

2-9

http://www.tyan.com

2.5.7 Front Panel LAN1/LAN2 Speed LED Pin-Header: JP5/JP7

1

Pin 2: Green+

Pin 1: Orange+

PW 2

P1FAN

JP9

BIOS

JP17

Intel

E7 2 21

Intel

ICH6R

PCI-E1

SATA2

SATA1

FDD J9

JP20

IDE J1 3

DIMM3

DIM M2

DIM M1

SMSC

I/O

BT1

DIMM4

PCI-E2

LED1

SA T A3

SATA4

FAN6

BROADCOM

LAN

(Optional)

JP 16

JP10

JP13

JP15

S5150

K B (B o tto m )

Mouse(Top)

JP11

JP12

BROADCOM

LAN

(O p t i o n a l )

JP 6

JP 3

SMDC JP19

JP4

J5

32-bi t 33MHz (5V) PCI J11

S O_DIMM J10

64-bit 10 0MHz PCI-X J12

J4

USB1

J1

KB / MS

J3

(COM1)

J2

(V G A )

LAN 1

LAN 2

LPT J8

Intel

PXH

JP 7

JP5

JP 2

JP 1

JP21

JP22

JP23

Use these headers to connect with the

front panel dual color LEDs to indicate the

speed of LAN1 and LAN2.

Off=10 LAN,

Green=100 LAN,

Orange=GbE LAN

Reference Section 2.11.1 for the correct

LAN LED Color Definition.

JP5 is for LAN1, JP7 is for LAN2.

2.5.8 CPU Fan Connector: JP9 (P1FAN)

+12V

V3P3

Speed Control

Tachometer

PW 2

P1 FA N

JP9

BIOS

JP1 7

Intel

E72 21

Intel

IC H 6R

PCI-E1

SATA2

SATA1

FDD J9

JP20

IDE J13

DIMM3

DIM M2

DIM M1

SMSC

I/O

BT1

DIMM4

PCI-E2

LED1

SATA 3

SA TA 4

FAN6

BROADCOM

LAN

(Optional)

JP 16

JP10

JP13

JP15

S5150

K B (B o tto m )

Mouse(Top)

JP11

JP12

BROADCOM

LAN

(O pt io n a l )

JP 6

JP 3

SMDC JP19

JP4

J5

32-bit 33MHz (5V) PCI J11

SO_DIMM J10

64-bit 100MHz PCI-X J12

J4

USB1

J1

KB / MS

J3

(COM1)

J2

(V G A )

LAN 1

LAN 2

LPT J8

Intel

PXH

JP 7

JP 5

JP 2

JP 1

JP21

JP22

JP23

Use this header to connect the processor

cooling fan to your motherboard to keep

the system stable and reliable.

This connector supports the tachometer

monitoring and auto fan speed control.

JP5

JP7

JP9

Tomcat i7221 S5150 Chapter 2: Board Installation

2-10

http://www.tyan.com

2.5.9 Front Panel USB 2.0 Connector: JP11/JP12

10 2

9 1

NC/Key

GND

Data 1+

Data 1 -

+5V

9 7 5 3 1

10 8 6 4 2

GND

Data 2+

Data 2 -

+5V

PW 2

P1FAN

JP9

BIOS

JP17

Intel

E72 21

Intel

ICH6R

PCI-E1

SATA2

SATA1

FDD J9

JP20

IDE J1 3

DIMM3

DIM M2

DIM M1

SMSC

I/O

BT1

DIMM4

PCI-E2

LED1

SA TA3

SA TA4

FAN6

BROADCOM

LAN

(Optional)

JP16

JP10

JP13

JP15

S5150

K B (B o tto m )

Mouse(Top)

JP11

JP 12

BROADCOM

LAN

(O p t i o n a l )

JP 6

JP 3

SMDC JP19

JP4

J5

32-bit 33MHz (5V) PCI J11

SO_DIMM J10

64-bit 100MHz PCI-X J12

J4

USB1

J1

KB / MS

J3

(COM1)

J2

(V G A )

LAN 1

LAN 2

LPT J8

Intel

PXH

JP 7

JP 5

JP 2

JP 1

JP21

JP22

JP23

Use these headers to Connect to the USB

devices via the enclosed USB cable.

2.5.10 Clear CMOS Jumper: JP13

3

1

Default

3

1

Clear

PW 2

P1FAN

JP9

BIOS

JP17

Intel

E72 21

Intel

ICH6R

PCI-E1

SATA2

SATA1

FDD J9

JP20

IDE J1 3

DIMM3

DIM M2

DIM M1

SMSC

I/O

BT1

DIMM4

PCI-E2

LED1

SA TA3

SA TA4

FAN6

BROADCOM

LAN

(Optional)

JP16

JP10

JP13

JP15

S5150

K B (B o tto m )

Mouse(Top)

JP11

JP 12

BROADCOM

LAN

(O p t i o n a l )

JP 6

JP 3

SMDC JP19

JP4

J5

32-bit 33MHz (5V) PCI J11

SO_DIMM J10

64-bit 100MHz PCI-X J12

J4

USB1

J1

KB / MS

J3

(COM1)

J2

(V G A )

LAN 1

LAN 2

LPT J8

Intel

PXH

JP 7

JP 5

JP 2

JP 1

JP21

JP22

JP23

Use this jumper when you forgot your

system/setup password or need to clear

system BIOS setting.

How to clear the CMOS data

- Power off system and disconnect

power supply from AC source

- Use jumper cap to close Pin_2 and 3

for several seconds to Clear CMOS

- Replace jumper cap to close Pin_1

and 2 (default setting)

- Reconnect power supply to AC

source

Power on system

JP11

JP12

JP13

Tomcat i7221 S5150 Chapter 2: Board Installation

2-11

http://www.tyan.com

2.5.11 Front Panel System Connector: JP14

Your chassis will usually come with connectors to install onto the motherboard, such as HD

and Power LEDs. The Front Panel Connector (JP14) has been implemented for such

purposes.

1 2

17 18

Function PIN PIN Function

HD_LED+ 1 2 PWR+

HD_LED- 3 4 PWR-

GND 5 6 Power Button

Reset

Button

7 8 GND

+5V 9 10 NC

NIMI 11 12 GND

+5VSB 13 14 NC

SMBUS

Data

15 16 GND

PW 2

P1FAN

JP9

BIOS

JP17

Intel

E7 2 2 1

Intel

ICH6R

PCI-E1

SATA2

SATA1

FDD J9

JP20

IDE J13

DIMM3

DIM M2

DIM M1

SMSC

I/O

BT1

DIMM4

PCI-E2

LED1

SATA3

SATA4

FAN6

BROADCOM

LAN

(Optional)

JP16

JP10

JP13

JP15

S5150

K B (B o tto m )

Mouse(Top)

JP11

JP 12

BROADCOM

LAN

(O p ti o na l )

JP 6

JP 3

SMDC JP19

JP4

J5

32-bit 33MHz (5V) PCI J11

S O_DIMM J10

64-bit 100MHz PCI-X J12

J4

US B1

J1

KB / MS

J3

(COM1)

J2

(V G A)

LAN 1

LAN 2

LPT J8

Intel

PXH

JP 7

JP 5

JP 2

JP 1

JP21

JP22

JP23

SMBUS

Clock

17 18 INTRU#

2.5.12 Front Fan Connector: JP15/JP17/JP21 (FAN2/FAN6/FAN4)

JP15 (FAN2)/JP21 (FAN4)

+12V

Speed Control

Tachometer

JP17 (FAN6)

+12V

Speed Control

Tachometer

PW 2

P1 FA N

JP9

BIOS

JP1 7

Intel

E72 21

Intel

IC H 6R

PCI-E1

SATA2

SATA1

FDD J9

JP20

IDE J13

DIMM3

DIM M2

DIM M1

SMSC

I/O

BT1

DIMM4

PCI-E2

LED1

SATA 3

SA TA 4

FAN6

BROADCOM

LAN

(Optional)

JP 16

JP10

JP13

JP15

S5150

K B (B o tto m )

Mouse(Top)

JP11

JP12

BROADCOM

LAN

(O pt io n a l )

JP 6

JP 3

SMDC JP19

JP4

J5

32-bit 33MHz (5V) PCI J11

SO_DIMM J10

64-bit 100MHz PCI-X J12

J4

USB1

J1

KB / MS

J3

(COM1)

J2

(V G A )

LAN 1

LAN 2

LPT J8

Intel

PXH

JP 7

JP 5

JP 2

JP 1

JP21

JP22

JP23

Use these headers to connect the chassis

cooling fans to your motherboard to keep

the system stable and reliable.

These connectors support the tachometer

monitoring and auto fan speed control.

JP14

JP17

JP21

JP15

Tomcat i7221 S5150 Chapter 2: Board Installation

2-12

http://www.tyan.com

2.5.13 Chassis Fan Connector: JP16 (FAN1)

+12V

Speed Control

GND

PW 2

P1 FA N

JP9

BIOS

JP1 7

Intel

E72 21

Intel

IC H 6R

PCI-E1

SATA2

SATA1

FDD J9

JP20

IDE J13

DIMM3

DIM M2

DIM M1

SMSC

I/O

BT1

DIMM4

PCI-E2

LED1

SATA 3

SA TA 4

FAN6

BROADCOM

LAN

(Optional)

JP 16

JP10

JP13

JP15

S5150

K B (B o tto m )

Mouse(Top)

JP11

JP12

BROADCOM

LAN

(O pt io n a l )

JP 6

JP 3

SMDC JP19

JP4

J5

32-bit 33MHz (5V) PCI J11

SO_DIMM J10

64-bit 100MHz PCI-X J12

J4

USB1

J1

KB / MS

J3

(COM1)

J2

(V G A )

LAN 1

LAN 2

LPT J8

Intel

PXH

JP 7

JP 5

JP 2

JP 1

JP21

JP22

JP23

Use this header to connect the chassis

cooling fans to your motherboard to keep

the system stable and reliable.

This connector supports the auto fan

speed control.

2.5.14 SMDC Connector: JP19 (Optional)

PW 2

P1 FA N

JP9

BIOS

JP1 7

Intel

E72 21

Intel

IC H 6R

PCI-E1

SATA2

SATA1

FDD J9

JP20

IDE J13

DIMM3

DIM M2

DIM M1

SMSC

I/O

BT1

DIMM4

PCI-E2

LED1

SATA 3

SA TA 4

FAN6

BROADCOM

LAN

(Optional)

JP 16

JP10

JP13

JP15

S5150

K B (B o tto m )

Mouse(Top)

JP11

JP12

BROADCOM

LAN

(O pt io n a l )

JP 6

JP 3

SMDC JP19

JP4

J5

32-bit 33MHz (5V) PCI J11

SO_DIMM J10

64-bit 100MHz PCI-X J12

J4

USB1

J1

KB / MS

J3

(COM1)

J2

(V G A )

LAN 1

LAN 2

LPT J8

Intel

PXH

JP 7

JP 5

JP 2

JP 1

JP21

JP22

JP23

For connection with Tyan Server

Management Daughter Card (SMDC)

*Optional on some versions of the S5150

motherboard.

JP16

JP19

Tomcat i7221 S5150 Chapter 2: Board Installation

2-13

http://www.tyan.com

2.5.15 PCI-X Speed Select Header: JP20

13

Pin 1-2 Closed: 133MHz

PW 2

P1 FA N

JP9

BIOS

JP1 7

Intel

E7 2 21

Intel

IC H 6R

PCI-E1

SATA2

SATA1

FDD J9

JP20

IDE J1 3

DIMM3

DIMM2

DIM M1

SMSC

I/O

BT1

DIMM4

PCI-E2

LED1

SATA 3

SA TA 4

FAN6

BROADCOM

LAN

(Optional)

JP 16

JP10

JP13

JP15

S5150

K B (B o tto m )

Mouse(Top)

JP11

JP 12

BROADCOM

LAN

(O p ti o na l )

JP 6

JP 3

SMDC JP19

JP4

J5

32-bit 33MHz (5V) PCI J11

SO_DIMM J10

64-bit 100MHz PCI-X J12

J4

USB1

J1

KB / MS

J3

(COM1)

J2

(V G A )

LAN 1

LAN 2

LPT J8

Intel

PXH

JP 7

JP 5

JP 2

JP 1

JP21

JP22

JP23

3

1

Pin 2-3 Closed: 100MHz

(Default)

2.5.16 SMDC/ASF2.0 Select Header:JP22/JP23

3

1

Support SMDC card

PW 2

P1 FA N

JP9

BIOS

JP1 7

Intel

E7 2 21

Intel

IC H 6R

PCI-E1

SATA2

SATA1

FDD J9

JP20

IDE J1 3

DIMM3

DIMM2

DIM M1

SMSC

I/O

BT1

DIMM4

PCI-E2

LED1

SAT A3

SA TA 4

FAN6

BROADCOM

LAN

(Optional)

JP 16

JP10

JP13

JP15

S5150

K B (B o tto m )

Mouse(Top)

JP11

JP 12

BROADCOM

LAN

(O p ti o na l )

JP 6

JP 3

SMDC JP19

JP4

J5

32-bit 33MHz (5V) PCI J11

SO_DIMM J10

64-bit 100MHz PCI-X J12

J4

USB1

J1

KB / MS

J3

(COM1)

J2

(V G A )

LAN 1

LAN 2

LPT J8

Intel

PXH

JP 7

JP 5

JP 2

JP 1

JP21

JP22

JP23

3

1

Support ASF 2.0

JP20

JP22

JP23

Page is loading ...

Tyan Tomcat i7221 S5150 User manual

This manual is also suitable for

Tyan Tomcat i7221 S5150 User manual

Related papers

Other documents