2. Lowrance
  3. Trippleshot Transducer

Lowrance Trippleshot Transducer Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Lowrance Trippleshot Transducer Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
For product manuals, technical
specications, certicates and
declarations refer to the product
website:
www.lowrance.com
*988-11775-001*
TRIPLESHOT
TRANSDUCER
INSTALLATION GUIDE
Details
Wiring
1. 2.
Parts included
1. Transducer with cable
2. Transom mounting kit
• 1x bolt and locking nut
• 2x metal washers
• 2x rubber washers
• 1x bracket and ratchet
• 2x self-tapping screws (10x1-1/4)
44.7 mm
(1.76”)
275.2 mm
(10.83”)
70.3 mm
(2.77”)
61.8 mm
(2.43”)
36.0 mm
(1.42”)
Environmental
Operating temperature -15°C to +55°C (+5°F to +131°F)
Storage temperature -30°C to +70°C (-22°F to +158°F)
Physical
Weight 0.48 Kg (1.06 lbs)
Cable length 6 m (20 ft)
Mounting options Transom mounting
Number of pins 8 pins
Sonar
Output Depth, SideScan imaging, DownScan imaging
and temperature
Frequency Traditional: 200 kHz/High Chirp
DownScan: 455 kHz, 800 kHz
SideScan: 455 kHz, 800 kHz
Beam width (@ -3dB) Traditional: 44° @ 200 kHz/High Chirp
DownScan: 55/2.5° @ 455 kHz, 35/1.5° @ 800
kHz
SideScan: 55/0.8° @ 455 kHz, 35/0.5° @ 800
kHz
Max depth Traditional: 152 m (500 ft) @ 200 kHz/High
Chirp
DownScan: 91 m (300 ft) @ 455 kHz, 46 m (150
ft) @ 800 kHz
SideScan: 183 m (600 ft) side-to-side @ 455
kHz, 91 m (300 ft) side-to-side @ 800 kHz
Max speed 57 knots (55 mph)
Mounting guidelines Transducer installation
Material 10# screw
Soft materials e.g. Plywood Ø 3.7-4.0 mm (5/32”)
Hard materials e.g. Fiberglass, Acrylic, Hardwoods Ø 4.2-4.7 mm (3/16”)
Recommended pilot holes:
1
A. Planing strake - avoid mounting
B. Avoid mounting within 1 m (3.3’) to port (left) of propeller
C. Avoid mounting within 7.5 cm (3“) to starboard of propeller
D. Best mounting location - undisturbed water ow
E. Trim tabs can cause turbulence - avoid mounting
Note: Example above describes a conventional clockwise propeller rotation
conguration. Mirror the example if your boat has a counterclockwise
propeller rotation conguration.
Note: If the transducer is not placed in a smooth ow of water, interference
caused by bubbles and turbulence may show on screen in the form of
random lines or dots. The unit could also lose bottom signal when the boat
is on plane. The sonar will not work while the transducer is out of the water.
A
B
C
D
E
F
2
3
4
A EB C D
5
A= 14° transom.
Torque to 2.8 N m (25 lbf in).
Apply a marine high-grade above- or
below-waterline sealant/adhesive
compound to the pilot holes.
/