Freedom9 2420 Quick Install Manual

Brand: Freedom9

Model: 2420

Type: Quick Install Manual

This manual is also suitable for

Quick Install Guide

freeConnect

Smart 2420

freedom to succeed

The location where you install the freeConnect Smart

2420 may greatly affect its performance. When installing

the unit, consider the following suggestions:

1. Install the switch in a cool and dry place within the

operating temperature and humidity ranges.

2. Install the switch in a site free from strong electro-

magnetic field generators (such as motors), vibration,

dust, and direct exposure to sunlight.

3. Leave at least 4” (10 cm) of space at the front and

rear of the switch for ventilation.

4. Install the switch on a sturdy, level surface that can

support its weight, or in an EIA standard-size equipment

rack.

5. When installing the switch on a level surface, attach

the rubber feet to the bottom of the switch. The rubber

feet cushion the switch and protect the case and surface

from scratches.

A. HARDWARE INSTALLATION:

w.freedom9.com

1-888-998-9189

PACKAGE CONTENTS:

• freeConnect Smart 2420

• AC power adapter

• Four rubber feet

• Screws and two mounting

brackets

• CD-ROM with Web Management

Utility and user’s guide

Quick Install Guide

for the freeConnect Smart 2420 24+2-port Web Smart switch

freeConnect Smart 2420

(S102411200)

The freeConnect Smart 2420 Web Smart

switch supports up to 24 10/100Mbps and

2 gigabit Combo-SPF connections using a

web-based interface for switch

management.

B. RACKMOUNTING:

The freeConnect Smart 2420 can be mounted in an EIA

standard-size, 19-inch rack, which can be placed in a

wiring closet with other equipement.

1. Attach the

mounting brackets

to the switch’s front

panel (one on each

side), and secure

them with the

screws provided.

(Figure 1).

2. Then, use the

screws provided with

the rack to mount

each switch in the

rack. (Figure 2).

C. NETWORK CONNECTION:

D. AC POWER:

The freeConnect Smart 2420 uses an AC power supply

operating at 100-240 AC, 50-60 Hz. The power switch is

located at the rear of the unit adjacent to the AC power

connector and the system fan.

Figure 1

Figure 2

The freeConnect Smart 2420’s 24 main ports support

10Mbps Ethernet and 100Mbps Fast Ethernet and run in

either half or full duplex mode using Category 5 or

higher cable.

The switch also has 2 gigabit Combo-SFP ports that can

each support either a 1000BASE-T connection or SFP

transceiver. The 1000BASE-T ports support 10Mbps

Ethernet and 100Mbps Fast Ethernet in half and full

duplex mode using Category 5 or higher cable and

1000Mbps Gigabit Ethernet in full duplex mode using

Category 5e or higher cable.

All RJ-45 ports support auto-MDIX, meaning that the

switch can automatically switch between MDI-II and

MDI-X types, allowing the use of either straight-through

or crossover cable regardless of the device on the other

end.

E. CONFIGURATION:

Once the freeConnect Smart 2420 is installed and

powered on, a computer connected to the switch

through the network can be used to configure the

switch. The default IP address of the freeConnect Smart

2420 is 192.168.0.1. The switch can be configured

using the Web Management Utility included in the CD

that came with the switch, or using a web browser.

Refer to the manual for more details on configuring the

switch.

Freedom9 2420 Quick Install Manual

Brand: Freedom9

Model: 2420

Type: Quick Install Manual

This manual is also suitable for

Download PDF

report

Freedom9 2420 Quick Install Manual

This manual is also suitable for

Freedom9 2420 Quick Install Manual

Related papers

Other documents