Anolis Ambiane™ User manual

Brand: Anolis

Model: Ambiane™

Category: Stroboscopes & disco lights

Type: User manual

This manual is also suitable for

Anolis Ambiane™ PW is a versatile LED fixture designed for indoor use, offering precise lighting control and a variety of mounting options. With its high-power LEDs, it generates bright, energy-efficient light that can be tailored to suit different needs. The Ambiane™ PW is suitable for various applications, including general illumination, accent lighting, and creating specific moods or atmospheres. It can be controlled via DMX, DALI, or 0-10V, making it compatible with a wide range of lighting systems.

User manual

Ambiane PW

The unit generates light by means of high power LEDs. The product was designed for indoor use only.

1. Attention

 Theunitmustbeinstalledbyaqualiedelectricianinaccordancewithall

national and local electrical and construction codes and regulations.

The unit was designed for indoor use only.

Avoid looking directly into the LED light beam at close range!

 Donotinstalltheunitnearhighlyinammableliquidsormaterials.

Do not allow anything to rest on the unit.

 Donotinstalltheunitnearanopename.

Do not install the unit in dirty,dusty or badly ventilated location.

 Sucientairaccessingtothehousingoftheunithastobeensured,

there must not be any heat or anti-noise insulation within a 0.6m x 0.6m

 areaaroundtheunit(non-ICratedxture).

Resistance of the equipment is designed for electromagnetic environments E1, E2, E3

according to the standard EN55103-2 ed.2 Electromagnetic compatibility. Product family

standard for audio, video, audiovisual and entertainment lighting control apparatus for

professional use. Part 2: Immunity.

The installation company should check levels of possible interferences above the tested levels

 E1,E2,E3givenbythisstandard(e.g.transmittersinsurroundingarea)beforeinstallingtheequipment.

Emission of the equipment complies with the standard EN55032 Electromagnetic compatibility

of multimedia equipment – Emission Requirements according to class B.

Suitable for fastening on Unsuitable for covering by heat insulation

 non-ammablesurfacesonly  material

Alvays switch o power suply of the unit before connecting or disconnecting the unit

2. Installation

1.Prepareacircularopeninginthelowerceiling(1)asshowninthepicturebelow.

2.InserttheAmbianeunitintotheopening.Fastenthexturebymeansoftwospringfasteners(2)totheopening

Toconnectneededcablestothexture,unscrewtwoscrews(4)fromtheplasticcover(3)andchipneeded

plasticthin-walledcovers(6)oinordertopasscablestotheconnectionblocks(5).

Theconnectionblocks(5)havethefollowingwiring:

Theprimarypowerinputservesforastandardpower(e.g.ArcPowerforAmbiane).

Thesecondarypowerinputservesforabackuppower(incasethatprimarypowerfailed).

If both power inputs are under voltage, the primary power has a priority and the secondary power is disabled.

fthextureissuppliedviathesecondarypower,thelightoutputofthexturecanbesetbyatrimmer.

Thexturecanbecontrolledbyoneofthefollowingmethods:DMX512

0-10V

DALI

ThextureisequippedwithtwoDMXandDALIconnectionblocksforeasyconnectiontoDMXorDALIchain

(In/Outmethod).

DMX connection 0-10V connection Power connection

PCB Function PCB Function PCB Function

0V - Shield 0V 0V + Power +

D+ Signal(+)   D+ +10V    - Power-

D- Signal(-)

3. DMX and DALI address setting and control

The DIP switch, located next to the connection blocks, allows to set a method of control, run test and also allows

toswitchthexturetotheupdatemodeincaseofsoftwareupdate.

DIP 10 - if switched to ON=test light

DIP11-selectionofxturecontrol:OFF=DMX512orDALI,ON=0-10V

DIP12-changefromOFFtoONpositionswitchesthexturetotheupdatemode(switchingtotheupdate

modeisnotnecessaryIftheRobeUploaderisusedforxtureupdate).

DMX control

TheDMXstartaddress,istherstchannelusedtoreceiveinstructionsfromtheDMXcontroller.Theaddress

maybeanychannelfrom1to512.DMXaddresscanbeseteitherbyDIPswitchorbyRDM.DMXaddress

setbyRDMoverwritesaddresssetbyDIPswitchandviceversa.ThegreenLEDonPCBsignalswayofDMX

address setting:

 LEDlights-DMXaddressissetbymeansoftheDIPswitch.

 LEDdoesnotlight-DMXaddressissetbymeansofRDM.

DIP 11 has to be set in OFF position.

ExampleofDMXaddresses:

DALI control

AddressingofthextureismadebymeansofanexternalDALIcontroller.TheexternalDALIcontrollerhasto

sendactivatingcommand(8=ON)ifyouneedtostartthepermanentcontrolofthexture(xturewillnotrespond

toDMXcommands)anddeactivatingcommand(0=OFF)tostopcontrolofthexture.

DIP 11 has to be set in OFF position.

Note:IfDIP11=OFF(xtureiscontrolledbyDMXorDALI),therstcomingcommandswitchesthexturetothe

correspondingoperationmode(DMXoperationbyaDMXcommand,DALIoperationbyaDALIcommand).E.g.

thexturestaysinaDALIoperationandcomingDMXcommandswitchesthexturetoDMXoperation.Next

commandisaDALIcommandandswitchesthexturetotheDALIoperationetc.Ifyouneedthepermanent

DALIoperation,youhavetosendaDALIcommand8tothexture.

0-10V control

DIP 11 has to be set in ON position. 0-10V operation has priority to DALI commands.

4. RDM

ThisxturesupportsRDMoperation.RDM(RemoteDeviceManagement)isabi-directionalcommunication

protocolforuseinDMX512controlsystems,itisthenewopenstandardforDMX512devicecongurationand

status monitoring.

RDMallowsyoutosetDMXaddress,selectDMXmodeandreadoutsoftwareversionofthexture.The.RDM

protocolisalsousedforthesoftwareupdateofthexturebymeansoftheRobeUploader.

5. Anti-glare ring installation

Inserttheantiglarering(1)intothextureuntilthreelocks(2)snapintoslots(3).

6. Adapter ring installation

1.Removebothspringfasteners(2)byunscrewingthefourscrewsM4x10(1).

2.Slidetheadapterring(4)ontothehousingofthexture.Screwthenewfasteners(3)onthehousing.

UseoriginalscrewsM4x10(1).

7. DMX protocol

version 1.1

Mode 1

Channel

Mode 2

Channel

Value Function Type of control

1 1

0-255

Dimmer

Light intensity coarse 0% -->100% proportional

- 2

0-255

Dimmer Fine

Light intensity from min. -->max. proportional

8. Technical specications

Inputvoltage:     24VDC

Max.powerconsumption:   40W

Protection class : CE: (ClassIII)

ETL: Class 2 or LVLE

Beam angle: 67°, 80° with anti-glare ring

Colourtemperature:    2700K,3200K,4000K,5000K,6500K

Control:     DMX,DALI,0-10V,RDMcompatible

DMXchannels:     1(Mode1),2(Mode2)

Typical Lumen maintenance: 70%@ 50,000 hours

Led life expectancy: minimum 50,000 hours

Operatingambienttemp.range:  -20°C/+45°C(-4F/+113F)

Operatingtemperature:   75°C@Ambient+35°C(167°F@Ambient+95°F)

Totalheatdissipation:    136BTU/h(calculated)

Cooling : convection

Totalheatdissipation:    136BTU/h(calculated)

Housing: alluminium

Weight:     1.8kg

Installation method: via two spring fasteners

IC rating: non-IC rated

Power/DMX/DALIconnection:   screwconnectionblockDegsonDG306-5.0-02P

      (Wirerange:22-14AWG(UL),1.5mm

(IEC))

Max.distancebetweenAmbianeand

ArcPowerforAmbiane:   1m(for2x18AWGcable)

Protectionfactor:    IP20(withoutdiuserglass),IP20/IP54(withDiuserGlass)

AmbianewithoutDiuserGlass    AmbianewithDiuserGlass

9. Optional Accessories

ArcPowerforAmbiane(P/N10063035)

Anti-GlareRing(P/N10980386)

DiuserGlassFrosted(P/N10980387)

AdapterRing(235-255mm)(P/N10980388)

10. Maintenance

Keepthextureclean,especiallylightsourceandtheribbedhousing.

11. Dimensions

mm [inch]

12. Software update

Software update by means of the DSU le.

The following items are required in order to update software:

-PCrunningWindowsorLinuxormacOS

-DSUle

-FlashcableRS232/DMX(P/N13050624)ortheRobeUniversalInterface/RobeUniversalinterfaceWTX.

Toupdatesoftwareinthexture:

1.DSUleisavailablefromAnoliswebsiteathttps://www.anolislighting.com/

FilewithextensionzipisintendedforWindows(usedandtestedfromXPtoW10on32/64bitsystems).

FilewithextensiontbzisintendedforLinux(usedandtestedonDebianandUbuntu32/64bit).

File with extension dmg is intended for

macOS(usedandtestedonOSXuptoSierra)XQuartzrequired,

install it from https://www.xquartz.org/

Savethedownloadletoafolderonyourcomputer.

Incasethatyouusewindows,extractlesintheziple(e.g.DSU_Ambiane_18051040.zip)

2.SwitchthextureoanddisconnectthexturefromDMXcontroller(IfyouuseDALIcontrol,switcho

theDALIcontroller).

3.IfyouusetheashcableRS232/DMX,connectaserialportofyourcomputerwithDMXinputofthexture

by means of this cable (probably you will need some USB to RS 232 converter if your computer has

USBportsonly).

If you use the Robe Universal Interface, connect a USB port of your computer with the Robe Universal Interface

bymeansoftheUSBcableandDMXinputofthexturewiththeDMXoutputoftheRobeUniversalInterface

viaaDMXcable.

4.Switchthextureonandswitchittotheupdatemode(svitchthe

DIP12fromOFFtoONposition)

Werecommendtocancelallrunningprogramsonyourcomputerbeforestartingthesoftwareuploader.

5.Double-clickthesoftwareuploaderle(e.g.DSU_Ambiane_18051040.exe)in

theextractedles.TheSoftwareUploaderprogramwillstartrunning.

6.Selectcorrect"COM"numberifyouusea

FlashcableRS232/DMX

or select "

Robe Universal Interface "

if you use the

RobeUniversalInterface/RobeUniversalInterfaceWTX

and then click on the "Connect" button.

7. If the connection is OK, click the “Start Uploading" button to start software uploading. It will take several

minutes to perform software update.

If the option "Incremental Update" is not checked, all processors will be updated (including processors with

thesamesoftwareversion).

If you wish to update only processors with new version of software, check the “Incremental Update

box“.

Avoid interrupting the process. Update status is being displayed in the "Info Box" window.

Whentheupdateisnished,thelinewiththetext“Fixtureissuccessfullyupdated“willappearin

this window.

8.SwitchthextureoandsettheDIP12toOFFposition.

Incaseuploadprocessisinterrupted(e.g.powerloss),thexturestaysin“Updatingmode”andyouwillhave

to repeat the software update again.

Software update by means of the Robe Uploader

Anotherway,howtoupdatesoftwareinthextures(especiallylargeinstallationofxtures)istousetheROBE

Uploader.ItisasoftwareforautomatizedsoftwareupdateofRobeandAnolisxtures.Ittakesadvantageof

RDMsupport.

Thextureshastobeconnectedinadaisy-chain(max.32xtures)andvia

the

Robe Universal Interface/Robe

UniversalInterfaceWTX

and a USB cable connected to the control PC with the Robe Uploader running.

The control PC should be connected to the Internet.

The Robe Uploader software and user manual is available at :

https://www.robe.cz/robe-uploader/

Note:

IfyoudothesoftwareupdatebymeansoftheRobeUploader,switchingxturestotheupdatemode(andfrom

theupdatemode)ismadeautomatically,withoutneedtoswitchtheDIP12toONposition.

TheRobeUploadersoftwarecannotbeusedifxturesareconnectedbymeansofDALIconnection.

Version1.9March4,2021

Specications are subject to change without notice.

Made in CZECH REPUBLIC by ROBE LIGHTING s.r.o. Palackeho 416/20 CZ 75701 Valasske Mezirici

Anolis Ambiane™ User manual

Brand: Anolis

Model: Ambiane™

Category: Stroboscopes & disco lights

Type: User manual

This manual is also suitable for

Download PDF

report

Anolis Ambiane™ User manual

This manual is also suitable for

Anolis Ambiane™ User manual

Related papers

Other documents