Freescale Semiconductor M9328MX21ADSE User manual

Document Number: UMS-21100

Rev. A

07/2006

M9328MX21ADSE

Application Development System

User’s Manual

M9328MX21ADSE User’s Manual, Rev. A

Freescale Semiconductor 1

Chapter 1 General Information

1.1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

1.2 M9328MX21ADSE Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

1.3 System and User Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

1.4 M9328MX21ADSE Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

1.5 ADS Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

Chapter 2 Configuration and Operation

2.1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

2.2 Configuring Board Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

2.2.1 Peripheral Selection Switch (S1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

2.2.2 Mode/User Switch (S2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

2.3 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

2.3.1 Functional Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

2.3.2 On-Board Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

2.3.3 Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

2.3.4 USB On-The-Go Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6

2.3.5 UART and IrDA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6

2.3.6 Ethernet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7

2.3.7 Touchscreen ADC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8

2.3.8 CD Quality CODEC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9

2.3.9 Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9

2.3.10 Memory Mapped I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10

2.3.11 Audio Indicator (Buzzer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12

2.3.12 LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12

2.4 Using The Board Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12

2.5 Add-On Module Connections and Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13

2.5.1 Using the TFT LCD Display Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-15

2.5.2 Using the Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16

2.5.3 Using a NAND Flash Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16

2.5.4 Using a SD/MMC Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16

2.5.5 Using Image Sensor Daughter Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16

2.5.6 Using the PCMCIA Daughter Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16

2.5.7 Using the TV Encoder Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-17

Chapter 3 Support Information

3.1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

3.2 CPU to Base Board Connectors PX1, PX2, PY1, and PY2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

3.3 CPU to Option Card Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12

3.4 UART/RS-232 Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-18

3.4.1 UART1 Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-18

3.4.2 UART4 Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-19

3.4.3 External UART Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-20

M9328MX21ADSE User’s Manual, Rev. A

2 Freescale Semiconductor

3.5 Multi-ICE Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-20

3.6 Ethernet Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-21

3.7 USB OTG Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-22

3.8 NAND Flash Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-22

3.9 External Keypad Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-25

3.10 LCD Panel Connector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-26

3.11 TV Encoder Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-27

3.12 SD/MMC Connector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-28

3.13 Extension and Image Sensor Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-28

3.14 Disposal Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-33

M9328MX21ADSE User’s Manual, Rev. A

Freescale Semiconductor P-1

About This Book

This manual explains how to connect and operate the M9328MX21ADS i.MX21 Application

Development System.

Audience

The audience for this manual is handheld communication device designers. It is assumed that users are

engineers or technicians with experience using development systems.

Organization

The manual consists of three chapters.

• Chapter 1 General Information introduces the user to the features and capabilities of the ADS.

• Chapter 2 Configuration and Operation contains configuration information, connection

descriptions, and other operational information that may be useful during the development process.

• Chapter 3 Support Information contains connector pin assignments, connector signal descriptions,

and other useful information about the ADS.

Revision History

The following table summarizes changes to this document since the previous release (Rev. A).

Conventions

Units and measures in this manual conform to the International System of Units (SI) as defined by

National Institute of Standards and Technology Special Publication 811.

Revision History

Location Revision

M9328MX21ADSE User’s Manual, Rev. A

P-2 Freescale Semiconductor

Definitions, Acronyms, and Abbreviations

The following acronyms and abbreviations are used in this manual. This list does not include signal,

register, and software mnemonics.

ADS Application Development System

CD Compact Disk

CMOS Complementary Metal Oxide Semiconductor

CODEC Code/Decode

CPU Central Processing Unit

DCE Data Communications Equipment

DIN Deutsches Institut für Normung

DIP Dual In-line Package

DTE Data Terminal Equipment

DUART Dual Universal Asynchronous Receiver/Transmitter

I

2

C Inter-Integrated Circuit

ICE In-Circuit Emulator

I/O Input/Output

IrDA Infrared Data Association

JTAG Joint Test Access Group

LCD Liquid Crystal Display

LED Light Emitting Diode

MB Megabyte

MCU Microcontroller Unit

MMC Multi-media Card

NAND Negative AND

OTG On the Go

PC Personal Computer

PCMCIA Personal Computer Memory Card International Association

SD SanDisk (Smart Media)

SDRAM Synchronous Dynamic Random Access Memory

SI System International (international system of units and measures)

SSI Synchronous Serial Interface

TFT Thin Film Transistor

UART Universal Asynchronous Receiver/Transmitter

USB Universal Serial Bus

VDC Volts Direct Current

M9328MX21ADSE User’s Manual, Rev. A

Freescale Semiconductor 1-1

Chapter 1 General Information

1.1 Description

The M9328MX21ADSE helps you develop applications for the i.MX21 MCU.

The ADS has 19 connectors and sockets that support application software, target board debugging, and

optional circuit cards. A separate LCD display panel and a separate keypad are supplied with the ADS.

When you connect the LCD panel and keypad to the ADS Base board, they align with each other.

1.2 M9328MX21ADSE Features

ADS features include:

• i.MX21 Multimedia Application Processor

• Two clock-source crystals, 32.768 KHz and 26 MHz

• Power connector for +5.0-volts in from an external regulated power supply, an in-line fuse, and a

power on/off switch.

• Voltage regulators that step down the 5.0 VDC input to Vcc (3.0 VDC), 2.5 VDC, 1.8 VDC and

1.5 VDC

• Multi-ICE debug support

• Two 8 MB × 16-bit Burst Flash memory devices configured as one 32 MB, 32-bit device

• Two 16 MB × 16-bit SDRAM devices configured as one 64 MB, 32-bit device

• High speed expansion connectors for adding optional cards.

• Two-board system: modular CPU board plugs into Base board; Base board has connections for

LCD display panel and keypad

• Memory mapped expansion I/O

• Software readable board revisions

• Configuration and user definable DIP switches

• SD/MMC memory card connector

• Two RS-232 transceivers and DB9 connectors (one configured for DCE and one for DTE

operation) supporting on-chip UART ports

• External UART with RS-232 transceiver and DB9 connector

• IrDA transceiver that conforms to Specification 1.4 of the Infrared Data Association

• USB OTG (On The Go) interface transceiver and USB mini AB connector

• Separate LCD panel assembly that connects to the Base board and interfaces directly with the ADS

• Touch panel controller for use with the LCD

• Separate keypad unit with 36 push button keys

General Information

M9328MX21ADSE User’s Manual, Rev. A

1-2 Freescale Semiconductor

• Separate CMOS Image Sensor Card

• Audio CODEC includes an 11.28 MHz crystal oscillator, a 3.5 mm audio input jack, a 3.5 mm

microphone jack, and a 3.5 mm headphone jack

• Cirrus Logic CS8900A-CQ3Z Ethernet controller, with RJ-45 connector for connecting to a system

hub

• Two 32 × 3-pin DIN expansion connectors with most i.MX21 I/O signals

• Variable resistor for emulation of a battery voltage level

• NAND Flash card (Plugs into CPU Board)

• LED indicators for power, external bus activity, Ethernet activity, and two LEDs for user defined

status indiction

• Universal power supply with 5.0-volt output @ 2.4 Amperes

• USB cable

• RS-232 serial cable

• Two RJ-45 Ethernet cables, network, and crossover

1.3 System and User Requirements

To use the ADS, you need:

• An IBM PC or compatible computer that has:

— A Windows® 98, Windows ME™, Windows XP™, Windows 2000, or Windows NT® (version

4.0) operating system

— A parallel port and a Multi-ICE device (not included)

•A + 5 VDC power supply @ 2.4 A, with a 2 mm female (inside positive) power connector

(included)

CAUTION

Never supply more than +5.5-volts power to your M9328MX21ADSE.

Doing so can damage board components.

1.4 M9328MX21ADSE Diagram

Figure 1-1 shows the connectors and other major parts of the ADS Base board and CPU board.

General Information

M9328MX21ADSE User’s Manual, Rev. A

Freescale Semiconductor 1-3

Figure 1-1. M9328MX21ADSE Application Development System

Important board components on the CPU card are:

• U5 — i.MX21 MCU

• PX1, PX2 — connections to the Base board (bottom side)

• PK1, PK2 — connections to option cards

• P20 — ARM Multi-ICE connector

• PM1 & PM2 — NAND Flash card connectors

• J1, J2, J3 — Power interruption jumpers for measuring CPU current consumption

Important board components on the Base board are:

• PY1, PY2 — connections to the CPU board

• P1 — RS-232 DB9 connector for the processor’s UART1, DCE pinout

• P2 — RS-232 DB9 connector for the processor’s UART4, DTE pinout

• P3 — RS-232 DB9 connector for the External UART, DCE pinout

• P4 — USB OTG connector

• P5 — Keypad module connector

• P6 — SD/MMC card connector

• P7 — LCD/touch panel connector

TV ENCODER

CON

LCD CON

+5V IN

P8

F1

SW1

P9

P3 P2 P1

P4

U16

VR1

P7

P5

KEYPAD CON

P6

PE1

CSI

PE2PE3

EXP CON 2

EXP CON 1

J7

ONE WIRE

P10

P11

P12

S1

LED2

LED3

LED4

LED7

LED6 LED5

LINE IN

MIC IN

HEADPHONE

P20

PK1

PK2

J3J1 J2

CPU BOARDBASE BOARD

ON

OFF

2A

ETHERNET

EXT UART DCE UART4 DTE UART1 DCE USB OTG

BATT EM

IrDA

ACT

SD2_D0

P13

SD/MMC

UART1_ON

UART4_ON

IrDA_ON

NEXUS_EN

JTAG_CTRL

TONE_OUT

PEN_CS_B

PEN_IRQ_B

LED1

1

2

3

4

5

6

7

8

S2

BOOT0

BOOT1

BOOT2

BOOT3

CLKMODE0

CLKMODE1

SW1 IRQ

SW2 READ

1

2

3

4

5

6

7

8

LINK ACT

RESET

SW2

BUZZER

VCC PWR

STAT2

STAT1

BUS ACT

5V PWR

DTR

J3

NC

SD2_D1

DSR

J4

NC

SD2_D2

CD

J5

SD2_D3

NC

RI

J6

MULTI-ICE

U5

CPU

PX1/PY1

PX2/PY2

U6

U8

U7

U9

3

2

1

PM1

PM2

NAND FLASH CARD

General Information

M9328MX21ADSE User’s Manual, Rev. A

1-4 Freescale Semiconductor

• P8 — 5.0-volt input power connector

• P9 — RJ-45 Ethernet connectors

• P10 — Line In to audio CODEC

• P11 — Microphone In to audio CODEC

• P12 — Headphone Out to audio CODEC

• P13 — TV Encoder connector

• PE1 — Connector to an Image Sensor card

• PE2, PE3 — I/O Extension connectors

• S1 — Peripheral enable and JTAG select DIP switches

• S2 — Boot mode, clock mode, and user defined DIP switches

• SW1 — Power switch

• SW2 — Reset switch

• LED1 — 5 volt power LED (green)

• LED2 — 3 volt power LED (green)

• LED3 and LED4 — General-purpose LEDs (orange)

• LED5, LED6 — Ethernet activity LEDs (green, orange)

• LED7 — external bus activity LED (red)

• U16 — IrDA transceiver

• VR1 — emulate the battery voltage level

• J3, J4, J5 and J6 — Modem control enable jumpers for RS-232 DTE interface on P2

• J7 — One wire interface

1.5 ADS Specifications

Table 1-1 shows M9328MX21ADSE specifications.

Table 1-1. Specifications

Characteristic Specifications

Clock speed (SDRAM/FLASH) CPU 266MHz, System 133MHz

Ports 10Base-T (RJ-45), RS-232 serial, USB OTG

Temperature:

operating

storage

0° to +50° C

-40° to +85° C

Relative humidity 0 to 90% (noncondensing)

Power requirements 4.5V

— 5.5 VDC @ 2.4 A

Dimensions 7.15 x 9.45 in (18.2 x 24.1 cm)

Configuration and Operation

M9328MX21ADSE User’s Manual, Rev. A

Freescale Semiconductor 2-1

Chapter 2 Configuration and Operation

2.1 Introduction

This section contains configuration information, connection descriptions, and other operational

information that may be useful during the development process.

2.2 Configuring Board Components

Table 2-1 is a summary of configuration settings. The following paragraphs provide additional information

about configuring and using the ADS.

Table 2-1. Component Configuration Settings

Component Position Effect

System Power Switch, SW1 Move this switch to the ON position to enable the power source

connected to P8 to power the system.

Factory setting is OFF.

System Reset Switch, SW2 Push to reset the M9328MX21ADSE.

Peripheral Selection Switch,

S1

The UART1 and UART4 transceivers are forced enabled, the IrDA

module is enabled by software, Nexus is disabled, ARM mode JTAG

is selected, and the buzzer is connected to PWMO. The LCD touch

panel signals are connected.

Factory setting is shown.

Subsection 2.2.1 explains other settings for this switch.

Mode Switch, S2

S2

Configures 32-bit Burst Flash as the boot device and the Default

clock bypass mode is selected.

Factory setting is shown

Subsection 2.2.2 explains other settings for this switch.

Power Headers

(on CPU card)

J1, VCC (3.0 V)

J2, 1.8 V

J3, 1.5 V

Connects specified power signal.

Factory Setting

(Leave jumper installed during normal use.)

Connect ammeter across pins to measure processor current

consumption from the specified power source.

SW1

ON

OFF

BOARD

EDGE

SW2

5

ON

4

8

S1

1

2

3

6

7

5

ON

4

8

S2

1

2

3

6

7

12

Configuration and Operation

M9328MX21ADSE User’s Manual, Rev. A

2-2 Freescale Semiconductor

2.2.1 Peripheral Selection Switch (S1)

S1 is a DIP switch that consists of eight slide switches. Seven of the switches enable and disable software

control of the UART transceivers, the IrDA buffers, the Nexus buffer, the touch panel controls, and the

buzzer. One switch selects JTAG operation mode.

Table 2-2 shows S1 functionality.

Figure 2-1 shows an example configuration. The switches are set so that the UART1 transceiver and the

IrDA module are forced enabled; the UART4 transceiver can be enabled by software; and the NEXUS

buffer and buzzer are disabled. In addition, ARM mode JTAG is selected and the LCD touch control

signals are enabled.

Modem Control Enable

Jumpers

(on Base board)

J3, DTR

J4, DSR

J5, CD

J6, RI

The specified RS-232 control signal of P2 connects to the specified

I/O signal.

J3 - DTR (pin 4) is controlled by SD2_D0 (output)

J4 - DSR (pin 6) can be read on SD2_D1 (input)

J5 - CD (pin 1) can be read on SD2-D2 (input)

J6 - RI (pin 9) can be read on SD2-D3 (input)

The specified RS-232 control signal of P2 is not connected to any I/O

signal and cannot be controlled or read.

J3 - DTR is forced active (positive), SD2_D0 is unused

J4 - DSR cannot be read, SD2_D1 is unused

J5 - CD cannot be read, SD2_D2 is unused

J6 - RI cannot be read, SD2_D3 is unused

Table 2-2. S1 Switch Settings

Switch Name Setting Effect

S1-1, UART1_ON

ON Forces the UART1 transceiver to be enabled.

OFF UART1_EN_B bit controls the UART1 transceiver

S1-2, UART4_ON

ON Forces the UART4 transceiver to be enabled.

OFF UART4_EN_B bit controls the UART4 transceiver

S1-3, IrDA_ON

ON Forces the IrDA module buffers to be enabled.

OFF IrDA_EN bit controls the IrDA buffers

S1-4, NEXUS_EN

ON Internal test only.

OFF Set to OFF for debugging purposes.

S1-5, JTAG _CTRL

ON Internal test only.

OFF ARM Multi-ICE mode selected after TRST.

S1-6, TONE_OUT

ON The buzzer is controlled by the PWMO output.

OFF PWMO is disconnected from the buzzer circuit.

S1-7, PEN_CS_B

ON CSPI_SS0 controls the chip enable of the Touch controller.

OFF Disables CSPI_SS0 control of the Touch controller chip enable.

S1-8, PEN_IRQ_B

ON UART3_CTS is connected to PENIRQ_B out of the Touch controller.

OFF UART3_CTS is not connected to PENIRQ_B out of the Touch controller.*

*PENIRQ_B is not connected to anything.

Table 2-1. Component Configuration Settings (continued)

Component Position Effect

123

Configuration and Operation

M9328MX21ADSE User’s Manual, Rev. A

Freescale Semiconductor 2-3

Figure 2-1. Switch S1

2.2.2 Mode/User Switch (S2)

S2 is a DIP switch that consists of eight slide switches. S2-1 to S2-4 configure boot mode and S2-5 and

S2-6 control the clock bypass modes. These switch settings take effect only on power up or after a reset.

S2 also provides two user definable switches (S2-7 and S2-8). S2-7 can be used to cause an interrupt when

switched (SW1_IRQ through signal UART3_CTS).

Table 2-3 lists the settings for the boot-mode subswitches, S2-1 through S2-4.

.

Figure 2-2 shows an example configuration. S2-1 through S2-4 configure the system to boot from the 8-bit

NAND Flash. S2-5 and S2-6 are always set to OFF. S2-7 and S2-8 are set for user-defined functions.

Figure 2-2. Switch S2

Table 2-3. Boot Mode Switch Settings

Boot Mode, Device

BOOT3

S2-4

BOOT2

S2-3

BOOT1

S2-2

BOOT0

S2-1

Internal bootstrap ROM (USB/UART) ON ON ON ON/OFF

NAND, 8-bit, 2KB per page ON ON OFF ON

NAND, 16-bit, 2KB per page ON ON OFF OFF

NAND, 16-bit, 512bytes per page ON OFF ON ON

CS0, 16-bit, D[15:0] ON OFF ON OFF

CS0, 32-bit ON OFF OFF ON

NAND 8-bit, 512bytes per page ON OFF OFF OFF

5

ON

4

8

TONE_OUT

IrDA_ON

UART1_ON

S1

1

2

36

7

JTAG_CTRL, (Set to OFF)

UART4_ON

NEXUS_ON, (Set to OFF)

PEN_CS_B

PEN_IRQ_B

5

ON

4

8

CLKMODE1, (Set to OFF)

BOOT2

BOOT0

S2

1

2

36

7

CLKMODE0, (Set to OFF)

BOOT1

BOOT3

SW1 IRQ

SW2 READ

Configuration and Operation

M9328MX21ADSE User’s Manual, Rev. A

2-4 Freescale Semiconductor

2.3 Operation

This section describes how the system functions and how to use the boards.

2.3.1 Functional Block Diagram

Figure 2-3 shows the functional interconnections of the ADS in a block diagram format.

Figure 2-3. Functional Block Diagram of M9328MX21ADSE

2.3.2 On-Board Memory

Figure 2-4 and Figure 2-5 show the on-board memory interface. The M9328MX21ADSE is equipped with

8M x 32-bit Burst Flash and 16M x 32-bit SDRAM. The chip selects CS0

and CS2 (CSD0) are used for

Burst Flash and SDRAM chip selects, respectively.

i.MX21

SDRAM

Burst Fl ash

Transceiver

CPU Board

High Speed

Connector s

Base boar d connector s

Addr /Data bus

IO pi ns

Ethernet

port

USB series

mini-AB

connector

UART1,

UART2 &

IrDA

Ext.

UART

LEDs & Buzzer

Boot mode,

UARTs, IrDA

selection

1-wire Interface

Silicon & Board

revision register

S/W readable

DIP switches

Audio

CODEC

UART

controller

Ethernet

controller

USB OTG

Transceiver

IO pi ns , PWM

OWIRE

Peripheral si gnals CSI signal s MMC/SD signal s

LCDC

USBOTG si gnalsAddr /Data BusAddr /Data Bus

UART signals

Decoder & Chip

select logic

Addr/Data Bu s

SSI

Base Board

Power Connector,

Power Switch & fuse

3V regulator, CPU

Reset signal

LCD

connector

Battery Level

Measurement

Emulation

Touch screen

controller

LCD panel

(240x320 pixels) & Touch

screen

White

LED

driver

LCD Board

TFT LCD DC-

DC converter

Keypad

Connector

Keypad Board

KPP

NAND Flash

Connector

Multi-ICE

connector

NFC si gnals

TV

Encoder

connector

I2C

Line In

Speaker

Out

Mic In

MMC/SD

connector

Image sensor

connector

Expansion

Connector 1

Expansion

Connector 2

Peripheral si gnals

2. 5V, 1.8V and

1 .5V r egulator s

Configuration and Operation

M9328MX21ADSE User’s Manual, Rev. A

Freescale Semiconductor 2-5

Figure 2-4. Burst Flash Interface

Figure 2-5. SDRAM Interface

2.3.3 Memory Map

Table 2-4 shows the memory map for external peripherals on the ADS board. Because the Burst Flash and

the Ethernet Controller do not take up the entire address space of the associated chip selects, software can

access the same physical memory location at more than one range of addresses. For instance, SDRAM uses

DQM3_EB3

A2...A24

D0.15

FLASH_RST RESET

A0...A22

D0..15

8MX16-Bit Burst Flash

CS

ACC

WP

WE

8MX16-Bit Burst Flash

CS0

V

CC

CLK

OE

AVD

BCLK

LBA

OE

D0.15D16..31

WEDQM1_EB1

RDYECB

V

CC

V

CC

RAS

CAS

DQM1_EB1

WE

A2..A18

D0..15

SDCKE0

SDCLK

DQM0_EB0

RAS

CAS

UDQM

WE

A0..10

D0..15

16MX16-Bit SDRAM

CS

CLK

CKE

LDQM

16MX16-Bit SDRAM

CS2

V

CC

A11

BA0

BA1

BA0

A20

A19

D0..15D16..31

UDQM

LDQMDQM3_EB3

DQM2_EB2

Configuration and Operation

M9328MX21ADSE User’s Manual, Rev. A

2-6 Freescale Semiconductor

the entire 64 MB address space allowed for CSD0, but the Burst Flash occupies only 32 MB of the 64 MB

space available to CS0, so it appears in two different ranges of addresses. CS1 covers 16 MB allowing

many repetitions of the memory mapped peripherals.

2.3.4 USB On-The-Go Interface

The i.MX21 USB OTG Device Module interfaces with a Phillips ISP1301BS USB transceiver connected

to P4, a mini AB USB connector. The interface can function as either a USB host or USB device. The

interface includes a Maxim MAX3355EUD+ USB power supply chip which can provide power on the

USB bus in host mode. This power supply chip is enabled by the USB_PWR signal. For details on the

operation of the USB interface, refer to the i.MX21 data sheet. Figure 2-6 shows the USB interface

connection.

Figure 2-6. USB OTG Interface

2.3.5 UART and IrDA

Figure 2-7 shows how to connect the UART and IrDA circuits.

Table 2-4. M9328MX21ADSE Memory Map

Peripheral Chip Select Address Range (HEX) Act Mem Size

SDRAM CSD0

0xC000_0000 to 0xC3FF_FFFF 64 MB

Burst FLASH CS0

0xC800 0000 to 0xC9FF_FFFF 32 MB

Ethernet Controller CS1

0xCC00 0000 to 0xCC00_000F* 16 BYTES

External DUART CS1

0xCC20 0000 to 0xCC20_000F* 16 BYTES

Read CPU and

Base board versions

CS1

Read 0xCC40_0000*

D7-D0 = CPU, D15-D8 = Base board

2 BYTES

Memory Mapped I/O

CS1

Write to 0xCC80_0000* (Output) 2 BYTES

CS1

Read 0xCC80_0000* (Input) 2 BYTES

* For I/O operations only D15 - D0 are used

USB Device

D+

D-

ISP1301BS

VBUS

ID

USB MINI AB

P4

MAX3355EUD+

USB_PWR

i.MX21

SHDN

VBUS

IDIN

IDOUT

Configuration and Operation

M9328MX21ADSE User’s Manual, Rev. A

Freescale Semiconductor 2-7

Figure 2-7. UARTs and IrDA Interface

2.3.6 Ethernet

The ADS is equipped with a Cirrus Logic CS8900A-CQ3Z Crystal LAN ISA Ethernet Controller that can

interface with the i.MX21. The CS8900A-CQ3Z has 10BaseT transmit and receive filters and operates in

I/O mode. Figure 2-8 shows the Ethernet interface.

Buffer

EN

IrDA

EN

UART1_TXD1

UART1_RXD1

UART1_CTS1

UART1_RTS1

RS232 Transceiver

P1

UART1

EN

V

CC

GND

S1-1

Software Enable

via MMIO Latch

RS232 Transceiver

P2

UART4

EN

V

CC

GND

S1-2

Software Enable

via MMIO Latch

V

CC

GND

S1-3

Software Enable

via MMIO Latch

UART3_TXD

UART3_RXD

USBH1_TXDM

USBH1_RXDP

USBH1_RXDM

USBH1_RXDP

SD2_D1

SD2_D2

SD2_D3

SD2_D0

RXD4

RTS

CTS

TXD4

DSR

*

CD

*

R

I*

DTR

*

* If enabled by jumper

DTE

DCE

i.MX21

Configuration and Operation

M9328MX21ADSE User’s Manual, Rev. A

2-8 Freescale Semiconductor

Figure 2-8. Ethernet Interface

2.3.7 Touchscreen ADC

The ADS is equipped with an Analog Devices AD7873BRQZ ADC. The ADC communicates with the

touchscreen of the LCD on the Base board. Variable resistor VR1 on the Base board can be used to change

the VBAT input voltage to the ADC. The i.MX21 communicates with the ADC via the CSPI1 interface.

Setting S1-7 to ON connects CSPI1_SS0 to the ADC chip select. Setting S1-8 to ON connects the ADC

interrupt out to UART3_CTS. Figure 2-9 shows the ADC interface.

Figure 2-9. ADC Interface

CS8900A-CQ3Z

RJ45 Connector

Isolation

Transformer

i.MX21

CS_LAN

BA1..3

D0..15

B_OE

B_RW

B_DQM3_EB3

UART3_RTS

SBHE

IOW

IOR

AEN

D0..15

INTRQ0

SA8

SA9

SA0

SA4..7

SA10..19

SA1..3

V

CC

CHIPSEL

P9

Y+

X+

V

CC

X-

Y-

LCD CONNECTOR

P7

VBAT

CS

DCLK

DOUT

DIN

i.MX21

UART3_CTS

PENIRQ

S1

CSPI1_SCLK

CSPI1_MISO

CSPI1_MOSI

CSPI1_SS0

VREF

VR1

AD7873BRQZ

8

7

Configuration and Operation

M9328MX21ADSE User’s Manual, Rev. A

Freescale Semiconductor 2-9

2.3.8 CD Quality CODEC

The ADS has a Wolfson WM8731SEDS 32-bit linear low power stereo CODEC with a built-in headphone

driver (U24). The CODEC is controlled by the i.MX21, which sends the digital audio data via an SSI2

interface and control data via an I

2

C interface.

The CODEC has stereo line and mono microphone level audio inputs as well as stereo headphone outputs.

It features a mute function, programmable line level volume control, and a bias voltage output suitable for

an electret type microphone. Table 2-5 shows the CODEC connectors and describes their basic functions.

The WM8731SEDS data sheet is available at http://www.wolfsonmicro.com/

2.3.9 Keypad

The ADS includes an external keypad module that connects to the Base board. The keys provide tactile

feedback. The i.MX21 keypad interface reads the pad via the KCOL[5:0] and KROW[5:0] signals. the

interface has chording diodes to prevent ghost key presses. The keys are labeled with numeric, cursor

control, soft key, and spare key functions, but the actual functionality is determined by user software. The

default keypad can be replaced by a custom design. The UART2 signals that are multiplexed internally

with the KCOL[7,6] and KROW[7,6] signals are brought out to keypad connector P5. This allows the use

of an 8x8 keypad matrix. Table 2-6 shows the key switch connections to the keypad signals by function

name (as labeled on the PCB) and the switch reference designators.

Table 2-5. Audio Connectors

Connector Descriptions

P10 Stereo line in jack

P11 Dynamic microphone input jack

P12 Headphone jack for audio out

Table 2-6. Keypad Layout and Connections

KCOL5 KCOL4 KCOL3 KCOL2 KCOL1 KCOL0

KROW5

APP1

SW1

SEND

SW2

KEY 1

SW3

UP

SW4

KEY 2

SW5

END

SW6

KROW4

APP2

SW7

HOME

SW8

LEFT

SW9

ACTION

SW10

RIGHT

SW11

BACK

SW12

KROW3

DOWN

SW13

APP3

SW14

1 -

SW15

2 ABC

SW16

3 DEF

SW17

EXTRA 2

SW18

KROW2

VOL UP

SW19

APP4

SW20

4 GHI

SW21

5 JKL

SW22

6 MNO

SW23

EXTRA 3

SW24

KROW1

VOL DOWN

SW25

EXTRA 1

SW26

7 PQRS

SW27

8 TUV

SW28

9 WXYZ

SW29

EXTRA 4

SW30

KROW0

POWER

SW31

RECORD

SW32

*

SW33

0 +

SW34

#

SW35

EXTRA 5

SW36

Configuration and Operation

M9328MX21ADSE User’s Manual, Rev. A

2-10 Freescale Semiconductor

2.3.10 Memory Mapped I/O

The ADS uses Memory Mapped I/O to add I/O functions without using the I/O resources of the processor.

The following paragraphs describe the I/O functions.

2.3.10.1 Input I/O

A memory read of hex address 0xCC80_0000 inputs the state of the ADS signals connected to latches U5

and U7. Table 2-7 shows which signal is associated with each data bit.

Table 2-7. Input Buffer Signals

BIT Signal Description

BIT 0 SD_WP Secure Data Write Protect

BIT 1 SW_SEL Software readable switch

BIT 2 RESET_E_UART External UART Reset

BIT 3 RESET_BASE Ethernet controller Reset

BIT 4 CSI_CTL2 Image Sensor control 2

BIT 5 CSI_CTL1 Image Sensor control 1

BIT 6 CSI_CTL0 Image Sensor control 0

BIT 7 UART1_EN UART1 transceiver enable

BIT 8 UART4_EN UART4 transceiver enable

BIT 9 LCDON LCD enable

BIT 10 IRDA_EN IrDA transceiver enable

BIT 11 IRDA_FIR_SEL Reserved

BIT 12 IRDA_MD0_B IrDA SD/Mode (inverted)

BIT 13 IRDA_MD1 Reserved

BIT 14 LED4_ON LED 4 control

BIT 15 LED3_ON LED 3 control

Page is loading ...

Freescale Semiconductor M9328MX21ADSE User manual

Freescale Semiconductor M9328MX21ADSE User manual

Related papers

Other documents