Sytech SYXT65BT Owner's manual

Brand: Sytech

Model: SYXT65BT

Category: Bluetooth music receivers

Type: Owner's manual

WELCOME

Welcome to Sytech! Thank you for purchasing the new Professional

Acoustic System SY-XT65BT. Please read this manual carefully before

operating your product and pay close attention to the precautions which

are mentioned below. Store this user manual in a safe place for future

reference

SAFETY INFORMATION AND WARNINGS

Symbol Definitions

DANGER- Indicates an imminently hazardous situation, which, if not

avoided, will result in death or serious injury. This symbol appears

only in the most extreme situations.

WARNING - Indicates a potentially hazardous situation which could

result in death or serious injury.

CAUTION- Indicates a potentially hazardous situation, which, if not

avoided, may result in minor/moderate injury or

product/property/damage. It also warns against unsafe practices.

Power source

This symbol means that this unit is double

insulated. An earth connection is not required.

The appliance must be connected to a 100-240V 50/60Hz. AC

supply by means of a two flat pin socket.

Unplug this apparatus during lightning, storms or when

unused for a long period of time to prevent damage to the

product.

The lightning flash with arrowhead symbol, within an

equilateral triangle is intended to alert the user to the

presence of insulated ‘dangerous voltage’ within the

product’s enclosure that may be of sufficient magnitude to

constitute a risk of electric shock to persons.

Warning: to reduce the risk of electric shock do not remove

cover (or back), no user serviceable parts inside refer

servicing to qualified service personnel.

The exclamation point within an equilateral triangle is intended

to alert the user to the presence of important operating and

maintenance (servicing) instructions in the literature

accompanying the appliance.

To prevent risk of fire or electric shock, avoid overloading

wall outlets, extension cords, or Integral convenience

receptacles.

Use suitable power sources - Plug the product into a suitable

power source, as described in the operating

instructions or as marked on the product.

The supply voltage should be the same as that indicated in

the technical specifications and the appliance rating plate. If

the socket outlets in your home are not suitable for the plug

supplied with this unit check with a qualified electrician for

replacement.

In order to disconnect the apparatus from the mains

completely, switch off the outlet and remove the mains plug

completely.

Do not bend, stretch or pull the supply cable in order to avoid

electric shock.

When installed, the power socket must be within easy reach.

Moisture and water

• Do not use this apparatus near water or moisture.

• Do not use this product near a bathtub, washbowl, kitchen

sink, laundry tub, wet basement, near a swimming pool or

anywhere else that water or moisture is present.

Heat sources and flames

• Batteries shall not be exposed to excessive heat such as sun

or fire.

• To prevent risk of fire or electric shock, avoid overloading wall

outlets, extension cords, or integral convenience receptacles.

Servicing and repairs

• Refer all servicing to qualified service personnel.

• Servicing is required when the apparatus has

been damaged in any ways: such as liquid

has been spilled or objects have fallen into

the apparatus; The apparatus has been

exposed to rain or moisture, does not operate

normally, or has been dropped.

Warning

The normal function of the product may be disturbed by strong

Electro-Magnetic Interference. If so, simply reset the product to

resume normal operation by following the instruction manual. In

case the function could not resume, please use the product in other

location.

SAFETY INSTRUCTIONS

1) Read this Instruction Manual before you attempt to connect or

operate the appliance.

2) Keep these instructions in good condition. Heed all warnings.

Follow all instructions.

3) Save this Instruction Manual for future reference.

4) The apparatus shall not be exposed to dripping or splashing and

no objects filled with liquids, such as vases, shall be placed on the

product. Use dry locations only.

5) No naked flame source, such as candles, should be placed on the

product.

6) Children should be supervised to ensure that they do not play with

the appliance.

7) Ventilation should not be impeded by covering the ventilation

openings.

8) Ensure that the unit is plugged into an AC 100-240V 50/60Hz

power outlet. Using higher voltage may cause the unit to

malfunction or even fire catching. Turn off the unit before

unplugging it from power source to completely switch it off.

9) Do not plug/ unplug the power plug into/from an electrical outlet

with wet hands.

10) Use replacement parts, which are specified by the manufacturer.

11) Install the unit in accordance with the manufacturer’s instructions.

12) Place the unit where there is good ventilation. Place the speaker

on a flat, hard and stable surface. Do not expose to temperatures

above 40°C. Allow at least 30 cm clearance from the rear and the

top of the unit as well as 5 cm from each side.

13) Press the buttons of the unit gently. Pressing them too hard can

damage the unit.

14) Always ensure that the product is unplugged from the electrical

outlet before moving or cleaning. Clean it with dry cloth only.

15) Unplug the product during lightning, storms or when it will not be

used for long periods of time.

16) This product has no user serviceable parts. Do not try to repair this

product yourself. Only qualified service personnel should perform

the service. Contact Sytech technical service for a proper

inspection and repair

17) NEVER let anyone, especially children, insert anything into the

holes, slots or any other openings in the unit’s casing as this could

result in a fatal electric shock.

18) Don’t mount this product on a wall or ceiling.

19) Do not place the unit near TVs, speakers and other objects that

generate strong magnetic fields.

20) Do not leave the unit unattended when it is in use.

NOTE: To disconnect the system completely if it’s not to be used for a

long time, remove the AC power plug from the wall outlet.

CONTROL PANEL & FUNCTIONS

BACK PANEL

1. AC in socket

2. Power switch

TOP PANEL

1. MIC+ Push up to increase the microphone volume.

2. MIC- Pull down de decrease the microphone volume.

3. GT+ Press to increase Guitar volume.

4. MODE Press to select mode function:

(Bluetooth, FM, AUX, USB).

5. Press to turn On or Off the unit.

6. GT- Press to decrease Guitar volume.

7. VOL Rotate VOL knob to increase or decrease the

Volume.

8. RGB Press to turn On or Off the RGB lights.

9. Press to pause or play/program.

10. Press to skip to the next track.

11. Press to return to the previous track.

12. ECHO-: Pull down to decrease the microphone echo effect.

13. ECHO+: Push up to increase the microphone echo effect.

14. LED: Display and remote sensor.

15. STANDBY: When unit is in Standby mode, the LED turns to red.

FRONT PANEL

1. Microphone input

2. Guitar input

3. USB Charging port. (5V. 1A)

4. USB port for playback

5. Aux input

REMOTE CONTROL

1. Switch to standby mode

2. Mute audio playback

3. Increase volume

4. Return to previous track

5. Skip to next track

6. Play and pause button

7. Decrease volume

8. Fast rewind

9. Mode button

10. Fast forward

11. Bluetooth mode

12. Press to unpair a connected

Bluetooth device.

13. USB input mode

14. EQ preset modes

Note: make sure to remove the plastic protector before

operating the remote for the first time.

Connecting the mains power cable:

1. Insert the power cord into the mains socket at the rear of the

unit.

2. Connect the mains plug to a wall outlet.

3. Set the “POWER” switch to “ON” position. The LED display

will illuminate.

4. Press the “STANDBY” button on the main unit or on the

remote control to turn on the unit.

5. To release the handle, press the button on top of the handle.

Input modes:

Follow the below instructions to switch between Bluetooth, FM radio,

AUX and USB input modes.

1. Press the MODE button on the main unit or on the remote

control repeatedly to cycle between Bluetooth, FM radio, and

AUX input modes.

2. Alternatively, press the button on the remote control for

direct access to Bluetooth or the USB button for direct access

to USB.

AUX-in input:

Follow the steps below to connect an external audio source

(Smartphone, tablet) to playback your tracks from your Party speaker.

You will need a 3.5mm audio cable or a 3.5mm to RCA cable (not

supplied) to connect your external device to the AUX input socket.

1. Connect one end of

the 3.5mm audio cable

to the AUX socket on

top of the unit. Connect

the other end to an

earphone or line out

socket of the external

audio device

(Smartphone).

2. Switch to AUX mode

by pressing the MODE

button on the main unit

or from the remote

control repeatedly until

AUX appears on the

LED display

3. Press PLAY on the external audio device.

4. Adjust the volume to your desired level.

Note: When connecting via the headphone output, the volume of the

party speakers is affected by the volume control on the player. Ensure

that the audio source (such as MP3 player, smartphone) is set to 70-

80% volume to avoid distortion.

FM Radio operation:

1. Press the MODE button on the main unit or from the remote

control to access to the FM Radio. The display will show “Fn” for

a moment and will then change to an FM Frequency.

2. Press the button on the main unit or on the remote control to

begin the auto scan process. The unit will save all the FM

stations detected.

3. Use the and buttons to cycle between the saved station

presets.

Note: The position of the party speaker is important for a good FM

reception. If you are unable to find a desired radio station, move the

party speaker to a different location and try to scan again.

Playback MP3 files from a USB:

Follow the steps below to connect a USB drive and playback MP3

files.

1. Insert a compatible USB flash drive into the USB port of the

speaker located on the top panel.

2. The device will be automatically detected and the first track in

folder 01 or the root of the USB will start playback automatically.

3. To pause playback, simply press the button on the main unit

or on the remote-control during playback. To resume playback,

press once more.

4. To skip to the next or previous track, use the or buttons.

USB / MP3 information:

• Do not remove the USB device during playback.

• A maximum of 999 tracks and 99 folders can be recognized.

• Make sure the USB device is formatted to FAT16, 32 formats.

• Maximum reading capacity is 64 GB.

Light effect” Led Flow”:

Press the LIGHT button to turn on or off the LED lights.

Guitar connection:

Follow the below steps to connect a guitar:

1. Connect the guitar plug to the GUITAR INPUT on the top panel of

the unit.

2. Once connected, adjust the volume with the GT+/GT- buttons.

Bluetooth connection:

To connect a smartphone or any other device to your speaker via

Bluetooth, follow the below steps:

1. Press the MODE button on the unit or from the remote control

until “Bt” appears on the LED display of the speaker. The “Bt”

display will be flashing informing that there is no connected

device.

2. Enable the Bluetooth function on your smartphone, tablet or any

other Bluetooth device which you wish to connect to your speaker

and search for “SY-XT65BT”. Once found, select it to pair your

external device to the speaker. The “Bt” on the LED display will

stop flashing once paired to your device.

3. In the case you are asked to enter a code, please enter “0000”

4. Once the speaker is connected to your external Bluetooth device,

a sound will be heard confirming the pairing of the two devices.

5. Each time you switch the Speaker on and select the Bluetooth

mode, the device will automatically pair and connect to the last

device, unless the device has been un-paired on your external

Bluetooth device.

6. Once the devices are paired up, press the Play/Pause button to

start playback.

7. When receiving a call during Bluetooth playback, the audio will

automatically stop playing. Once you hang up the call, the music

will restore.

8. The volume output is affected by the volume level from the

external audio source: For example, if you have paired your

smartphone, you will need to adjust the volume level from your

smartphone to avoid distortion.

9. To unpair the device from a Bluetooth connection, press the

PAIR button on the remote control. The speaker will revert

automatically to search mode and will be available for a new

connection.

Functions and controls:

Once your speaker is connected to an external device via Bluetooth,

you can use the controls located on the top panel of the speaker or

from the remote control.

: Playback or pause the track.

: Skip to the next track.

: Skip to the previous track.

Volume control:

• Rotate the volume knob clockwise on the top panel or press the

button on the remote control to increase the volume output.

• Rotate the volume knob counterclockwise or press the button

On the remote control to decrease the volume output.

Mute function:

• Press the MUTE button on the remote control to silence the audio

playback.

• Press once again to resume the audio output.

Troubleshooting:

Problem Reason Solution

No Power Power cable is not

connected to the

wall socket.

Power is not

switched on.

Make sure the plug

is connected.

Switch on the power.

No sound Volume output is too

low.

AUX/BT source is

too low.

Microphone volume

is too low.

Increase the volume.

Increase the output

volume of the

AUX/BT source.

Increase the volume

of either MIC or

Guitar input.

Sound is distorted Volume is too high.

AUX source volume

is too high.

Reduce the volume.

Reduce the output

volume of the AUX

source.

Remote control is

not working

The batteries are

flat.

Replace the

batteries of the

remote control.

Bluetooth

connection with an

Android device does

not output any

sound

Some older Android

builds may have

incompatibility

issues.

Use the volume

buttons on the

remote control only

to bypass the

incompatibility.

Accessories included:

1. Party speaker Led Flow

2. Remote control

3. AC cable

4. Instruction manual

Environment and Compliance:

The European directive 2012/19/EU on Waste Electrical

and Electronic Equipment (WEEE), requires that old

household electrical appliances must not be disposed of

in the normal unsorted municipal waste stream. Old

appliances must be collected separately in order to

optimize the recovery and recycling of the materials they

contain, and reduce the impact on human health and the environment.

The crossed out “wheeled bin” symbol on the product reminds you of

your

obligation, that when you dispose of the appliance, it must be

separately collected.

To avoid possible hearing damage, do not listen at high audio volume

for a long period of time.

TECHNICAL SPECIFICATIONS

Basic Specifications

High resistant material finishing

DSP audio processor

2-way electronic divider amplifier system

FM tuner with 30 preset memory stations

Built-in amplifier for connecting musical instruments: Electric guitar,

Electronic keyboard

4-digit LED display

Led Flow lights integrated on the speaker

Microphone input

Aux in

Remote control

2 wheels and handle

Bluetooth Specifications

Bluetooth Module: AC6901

Bluetooth Version: V.4.2 + EDR

Bluetooth Profiles: EDR, A2DP, AVRCP

Bluetooth Pairing name: SY-XT65BT

Compatible Audio Formats in Bluetooth: MP3/WMA

USB 1 Specifications

2.0 USB Port (Max Capacity : 64GB)

Compatible Audio Formats in USB: MP3/WMA

USB 2 Specifications

USB Port charging function

Power: 5V.1A

Technical Specifications

Power consumption: 165W. max.

Output power RMS: 120W

Output power PMPO: 600W

THD: <

0.3%

SNR: 72dB

Frequency response Woofer: 20Hz-4 kHz

Frequency response Tweeter: 2KHz-20KHz

Power supply: AC~100-240V 50/60Hz

2 ways speakers: Woofer: 2 x 10” 8 Ohms

Tweeter: 1 x 1.5” 6 Ohms

Dimensions and weight:

Unit dimension : (LxWxH): 31,0 x 32,0 x 96,5 cm.

Weight: 12,5 Kg.

Above specifications are the specifications of SY-XT65BT “Led Flow

Series” and are for reference purpose only.

Due to continuous product development, specifications may be subject

to change without prior notification.

Do not expose to adverse weather conditions (Such as rain or high

temperatures) as it can cause malfunctions

DECLARATION OF CONFORMITY

Manufacturer Name: Satyatrade S. L.

Address: Pol.Ind.La Raya. C/ Guadalquivir, 2.

Camarma de Esteruelas, 28816 Madrid

Tel: 902 430 967

Fax: 91 8864285

NIF: B84254763

Manufacturing country: China

Description: Party speaker Led Flow

Sytech® SY-XT65BT complies with the following directives:

RED Standard: Directive 2014/53/EU

EMC Standard: Directive 2014/30/EU

LVD Standard: Directive 2014/35/EU

ROHS Standard: Directive 2015/863/EU Restriction of Hazardous Substances

Signed: Ajeet Nebhwani Utamchandani

Sole Administrator

www.sytech.es

Sytech SYXT65BT Owner's manual

Brand: Sytech

Model: SYXT65BT

Category: Bluetooth music receivers

Type: Owner's manual

Download PDF

report

Sytech SYXT65BT Owner's manual

Sytech SYXT65BT Owner's manual

Related papers

Other documents