Extron VLH 302 Installation guide

Brand: Extron

Model: VLH 302

Type: Installation guide

This manual is also suitable for

Extron VLH 302 is a handheld microphone that offers wireless freedom and excellent audio quality for presentations, lectures, and discussions. With its long battery life and quick charging time, you can rely on it for extended use without interruptions. The microphone features a user-friendly interface with a power switch and a volume control knob, making it easy to operate. Additionally, the VLH 302 has a built-in auxiliary audio input, allowing you to connect external audio sources, such as MP3 players or laptops, for added versatility.

VoiceLift Pro Microphone Kits • Setup Guide

IMPORTANT NOTE:

Go to www.extron.com for the complete user guide, installation instructions, and specications

before connecting the product to the power source.

This guide provides instructions for an experienced installer to set up the Extron VLP 302 VoiceLift Compact Pendant Microphone,

the VLH 302 VoiceLift Handheld Microphone, the VLC 302 Charging Station, and the VLR 302 Receiver in a system with a

PVCA 452 Controller Amplier or PVS 407D PoleVault Digital Switcher.

Connecting the VLC 302 Charger and Charging the Microphones

11 22

LED

11 22

LED

NOTE: The charging station is to be used with NiMH rechargeable batteries

only.

To connect the charger and charge the microphone(s):

1. Connect the 5 VDC, 2.6 A wall charger (with USB Mini-B adapter) to a

110-130 VAC (US) or a 100-240 VAC (international), 50-60 Hz power

source (1).

2. Connect the USB mini plug end of the adapter to the USB mini jack located

on the back of the VLC 302 (2).

NOTE: The charger can also be powered by a USB source using a

mini USB cable.

3. If required, unscrew and remove the microphone battery cover to install the

battery. Insert the battery, aligning the + and – poles as indicated inside the

compartment.

VLP 302

(Cover Removed)

VLH 302

(Cover Removed)

BATTERY

4. Insert the microphone into one of the charger slots (4). The microphone

LED turns red to indicate charging, and green when the microphone is fully

charged.

NOTE: Microphones can be left to charge for extended periods.

CAUTION: Do not replace the batteries with an incorrect type. Use only

rechargeable batteries specified or provided by Extron, or alkaline batteries.

ATTENTION:

• Do not attempt to charge alkaline batteries.

• Be sure to replace the battery with the correct type and to dispose of used

batteries appropriately.

Setting Up the Microphones

VLP 302 Pendant Microphone

1. Verify that the battery is installed and fully charged.

2. Set the microphone(s) for either Teacher or Student mode using the

DIP switch, accessible from beneath the battery cover (see 2 at right):

• In Teacher mode (default), all microphone features are fully

functional. Set the dip switch to the OFF (down) position to enable

“teacher” mode.

• In Student mode, all buttons are disabled except for power. Set

the dip switch to the ON (up) position to enable “student” mode.

3. Apply the appropriate label (provided) to identify the microphone

(see 3 at right).

4. To wear as a pendant microphone:

a. Open the microphone clip (see a at right).

b. Slide up the lanyard lock under the clip, then release the clip (b).

c. Place the lanyard

around your neck.

Adjust both lanyard

straps so the

microphone rests

approximately

6 inches (15.2 cm)

below your chin.

TEACHER

~ 6”

Press to

open clip

Lanyard

Lock

~ 6”

Installing the VLR 302 Receiver

The VLR 302 Receiver outputs audio signals from the microphones as one balanced mono line

level signal to the PVCA 452 and PVS switcher. Connect the VLR 302 to the PVCA 452 or

PVS 407D PoleVault switcher as shown below. For mounting instructions, see the VoiceLift Pro

User Guide.

A Connect the PVCA 452 or PVS 407D to the VLR 302 output port using the included shielded

RJ-45 cable as shown below.

NOTE: The receiver is powered by the PVS switcher.

OUTPUT

1 C C2

RELAY

VLR 302 Receiver

LAN 1 LAN 3

LAN 2 LAN 4

DO NOT

GROUND

OR SHORT

SPEAKER

OUTPUTS

4/8

HDMI HDMI

1/2

SIG LINK SIG LINK

3/4 56

INPUTS OUTPUT

AUDIO OUT

PVS 407D

AMPLIFIED AUDIO OUT PAGING

SENSOR

PVT IN PVT IN

AUX

OVER PVTREMOTE

VOICELIFT

LAN

INPUT 7

RS-232

Tx Rx

S GG

CLASS 2 WIRING

LAN

- - A MAX

POWER

12V

L R

Out

POWER

12V

2.0 A MAX

INPUTS

OUTPUTS

AUDIO

HDMI/CEC/ARC

AUDIO

VOICELIFT

DIGITAL R

AUX

CLASS 2 WIRING

DO NOT

GROUND

OR SHORT

SPEAKER

OUTPUTS

4/8

AMPLIFIED AUDIO

PAGE

SENSOR

OUTPUT

1 C C2

RELAY

VLR 302 Receiver

PVCA 452

PVS 407D PoleVault Switcher

Out

B These relays can be integrated with various systems, or connected to a digital input on an Extron MediaLink MLC or a control

processor for Instant Alert capability (see the VoiceLift Pro User Guide for details). Wire this 4-pole captive screw Relay

connector for relays 1 and 2, if necessary.

VLH 302 Handheld Microphone

1. Verify that the battery is installed and fully charged.

2. Turn the microphone on by sliding up the power switch (2). One of the

LINK LEDs on the VLR 302 receiver illuminates to indicate that connection

has been established.

NOTE: Each VoiceLift kit includes VLP 302/VLH 302 microphones

and VLR 302 receivers that have already been paired. Follow the

steps on the next page to pair the microphone if necessary.

3. Speak in a normal tone of voice, adjusting the volume level (3) as

necessary (to save the volume level, see Saving the Microphone

Volume Level).

4. When nished, return the microphone to the charging station.

VLH 302

(Cover Removed)

Status

LED

5. Turn the microphone(s) on by holding the power button (5) for 3 seconds.

One of the LINK LEDs on the VLR 302 receiver illuminates to indicate that

connection has been established.

NOTE: Each VoiceLift kit includes VLP 302/VLH 302 microphones

and VLR 302 receivers that have already been paired. Follow the

steps on the next page to pair the microphone if necessary.

6. Speak in a normal tone of voice, adjusting the volume level (6) as

necessary (to save the volume level, see Saving the Microphone Volume

Level).

7. When nished, return the microphone to the charging station.

Status

LED

Saving the Microphone Volume Level

Saving the microphone level allows the microphone to recall the stored volume level setting when powering on. To save the

microphone volume level:

1. Adjust the volume on each microphone to the desired level.

2. Manually power down each microphone:

• For the pendant microphone, press and hold the power button until the LED turns off.

• For the handheld microphone, slide power switch to off position.

3. Wait 30 seconds before turning the microphones on or placing them in the charger.

Auxiliary Audio Connection

VLP 302

The 3.5 mm mono TS (tip/sleeve) aux audio input on the side of the VLP 302 microphone can be

used to connect an optional lavalier microphone (see the diagram below for connector wiring).

TS Connector

Tip

Sleeve

VLH 302

The aux audio input on the VLH 302 microphone can be used to connect audio devices (such as

mobile devices, MP3 players, etc.) to wirelessly transmit audio to the room speakers.

Use a 3.5 mm stereo TRS (tip/ring/sleeve) cable to connect the audio source to the aux audio input

on the side of the VLH 302 microphone (see the diagram below for connector wiring).

Sleeve (S)

Ring (R)

Tip (T)

Tip

Sleeve(s)

Ring

Tip

Sleeve

Tip

Unbalanced Input

TRS Connector

RCA Connector

Left

Right

Left

Right

Balanced Input or Output

Balanced Mono Audio

Unbalanced Stereo Audio

Tip

Sleeve

Ring

Tip

Sleeve

Unbalanced Output

Left

Tip

Sleeve(s)

NO Ground Here

Tip Right

CAUTION

For unbalanced audio, connect the

sleeves to the ground contact.

DO NOT connect the sleeves to the

negative (-) contacts.

Tip

Sleeve

NO Ground Here

Ring (R)

Ring

Tip (T)

Tip

Sleeve (S)

Ring (R) = Right Channel

Tip (T) = Left Channel

Sleeve (S)

(input or output)

Sleeve

3.5 mm Audio Jack

TRS

Auxiliary Stereo

Audio Input

Auxiliary Mono

Audio Input

Auxiliary Stereo

Audio Input

Auxiliary Mono

Audio Input

Pairing with the VLR 302 Receiver

Each VoiceLift kit includes VLP 302/VLH 302 microphones and VLR 302 receivers that have already been paired. If needed, follow

the steps below to pair microphones with a receiver.

Verify which Microphones are Paired

1. Ensure that the microphones are fully charged. Power each microphone on, one at a

time, to determine if the microphones are paired to the VLR 302 receiver.

NOTES:

• As each microphone is powered on, one of the VLR link slot LEDs (see A

at right) illuminates if the microphone is paired.

• Only one microphone can be paired to each LINK slot on the VLR receiver.

2. Once you have determined which microphones are paired, turn them o.

Pair New Microphones

Follow these steps to pair each microphone to the VLR 302 receiver.

NOTE: All paired microphones must be turned o before pairing new microphones.

1. Press and hold the LINK button on the VLR 302 receiver (see B in the image above) for 4 seconds to start pairing mode.

If LINK slots are available, one of the LINK LEDs blinks to indicate that pairing mode has started.

NOTES:

• Once initiated, pairing mode is enabled for 30 seconds. Users must repeat the process if they have

exceeded the 30 second pairing window or if pairing was not successful.

• Receiver Pairing/Discovery mode can also be enabled remotely using Product Configuration

Software (PCS) or SIS comands (see the VoiceLift Pro Microphone Kits User Guide). Commands

can be sent to the receiver through direct USB connection using a PVCA 452 connection or PVS

switcher connection.

• If adding a new microphone to the system (or replacing a current microphone), and both Link slots

are currently assigned, reset the VLR 302 to clear the pair history (see Clearing Pair History on

the next page).

2. Follow the steps below for your microphone model:

• For the VLP 302: Ensure that the microphone is powered off.

NOTE: The VLP microphone must be in “TEACHER” (o)

mode in order to pair.

Then, press and hold the POWER and FUNCTION buttons (see

A and B at right) simultaneously for 4 seconds until the status

LED blinks red and green, indicating pairing mode has started.

• For the VLH 302: Ensure that the microphone is powered on.

NOTE: The VLH microphone must be in “STUDENT” (on)

mode in order to pair.

Then, press and hold the LINK button, located beneath the battery cover (see C at right), for 4 seconds.

The microphone status LED changes from solid amber to alternating red and green, indicating that pairing

mode has started.

NOTES:

• The receiver assigns the microphone to the first available LINK slot.

• If the microphone is paired successfully, one of the LINK LEDs on the VLR receiver lights solid green.

3. After pairing the microphones, verify that they have been set up properly as shown in the previous section, Setting up the

Microphones on page 2. Repeat steps 1-3 for each microphone being paired.

A B

All trademarks mentioned are the property of their respective owners.

Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876

For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the Extron

Safety and Regulatory Compliance Guide on the Extron website.

68-2957-50

Rev. C

11 23

Clearing Pair History

Follow these steps to reset the VLR 302 pairing history, if needed, using the front panel

Reset button (see A at right). The following reset mode clears pairing history, but

retains settings and usage data.

1. Hold down the Reset button for about three seconds until the Power LED blinks

once.

2. Release and press the Reset button momentarily (for less than one second) within

one second.

Both Link 1 and Link 2 LEDs blink one time, simultaneously, to conrm that the pairing

history has been cleared. Unsolicited response “Pair00” is sent.

Extron VLH 302 Installation guide

Brand: Extron

Model: VLH 302

Type: Installation guide

This manual is also suitable for

Download PDF

report

Extron VLH 302 Installation guide

This manual is also suitable for

Extron VLH 302 Installation guide

Related papers

Other documents