K&H Hangin’ Cat Condo / Hangin’ High Rise Cat Tree User manual

Brand: K&H

Model: Hangin’ Cat Condo / Hangin’ High Rise Cat Tree

Type: User manual

Hangin’ Cat Condo - 3 Story

Assembly Instructions

K&H Pet Products, Central Garden & Pet

Colorado Springs, CO

www.khpet.com l (719) 591-6950

Made in China

Thank you for purchasing the 3 Story Hangin’ Cat Condo by K&H Pet Products.

Proper care and adjustment should lead to many years of pleasure for your cat.

Take the product out of the box and lay all parts on a at surface.

You should have four metal brackets, rubber bumper/spacers, and a

3 Story Hangin’ Cat Condo frame with built-in straps. See Figure 1.

Before installing the top two door brackets, rst determine whether

you will need to use the bumper/spacers provided for the type of

door you will be using. Our unique door bracket system is made to

t virtually any standard household door. For most thicker exterior

doors, i.e., front or back door of a home, the bracket can be used as

is. However, for thinner interior doors such as a bedroom or closet

door, we’ve provided stick-on silicone bumper/spacers to help remove

excessive gap between the bracket and the door. When using the

bumper/spacers, always determine rst which side of the door your

new Hangin’ Cat Condo will hang from.

NOTE: If the bumper/spacers are necessary, they should be attached

to the inside of the bracket OPPOSITE of the door jamb.

See Figure

2 for CORRECT placement.

(Never put the bumper/spacers on

the door jamb side of the bracket as this may prevent the door from

properly closing.)

See Figure 3 for INCORRECT placement.

If the bumper/spacers are not needed, simply install the plain brackets

as is to the top of your door. See Figure 4

Once the top brackets are installed, slide the remaining 2 brackets onto

the bottom of your door. See Figure 5.

Hold the Cat Condo from its top two straps and hook the clips at the

end of the straps onto the top two brackets. See Figure 6.

Once the Condo is hanging from the top two brackets, hook the bottom

two clips to the lower two brackets. Pull the cinch strap lightly on the

right and left side just enough to slightly tighten the brackets to the

underside of the door. See Figure 7.

At this time, adjust the top and bottom brackets to the correct width

apart so the Cat Condo hangs straight and is centered on the door.

Step back and adjust the top, and/or bottom. Be sure it is visually

straight and where you want it. Lastly, rmly pull down on each cinch

strap to secure the Condo to the door. Figure 8

shows a good visual

of correct positioning of the bottom brackets and how the straps

should look once cinched rmly to the door.

The K&H 3 Story Hangin’ Cat Condo will now keep your

cats busy for hours with plenty of places to play, hide, and lounge

for years to come. And don’t forget its space-saving benets!

ASSEMBLY & INSTALLATION INSTRUCTIONS:

K&H Pet Products with design is a registered trademark of Central Garden & Pet Company.

CORRECT

DOOR JAMB

BUMPER/

SPACER

BUMPER/

SPACER

INCORRECT

Figure 7

Care Instructions: When the 3 Story Hangin’ Cat Condo is

removed from packaging it is safe to steam in order to remove

unwanted wrinkles. To clean, wipe with a damp cloth.

Hangin’ High Rise - 5 Story

Assembly Instructions

K&H Pet Products, Central Garden & Pet

Colorado Springs, CO

www.khpet.com l (719) 591-6950

Made in China

Thank you for purchasing the 5 Story Hangin’ High Rise by K&H Pet Products.

Proper care and adjustment should lead to many years of pleasure for your cat.

Take the product out of the box and lay all parts on a at surface. You

should have four metal brackets, two black corrugated side panels, rubber

bumper/spacers, and a 5 Story Hangin’ High Rise frame with built-in straps.

Locate and install the black corrugated side panels into the pockets shown in

Figure 1. To do this, open the hook and loop enclosure pockets on both sides of

the top section of the High Rise. Slide the panels into the pockets. Be sure to note

the orientation of the black panels as they only t into the pockets one way. Once

you have completely inserted the corrugated plastic side panel, close the ap

and secure the hook and loop ap. Repeat on the other side. See Figure 1.

Before installing the top two door brackets, rst determine whether you will need

to use the bumper/spacers provided for the type of door you will be using. Our

unique door bracket system is made to t virtually any standard household door.

For most thicker exterior doors, i.e., front or back door of a home, the bracket

can be used as is. However, for thinner interior doors such as a bedroom or

closet door, we’ve provided stick-on silicone bumper/spacers to help remove

excessive gap between the bracket and the door. When using the bumper/

spacers, always determine rst which side of the door your new Hangin’ High

Rise will hang from.

NOTE: If the bumper/spacers are necessary, they should be attached to the

inside of the bracket OPPOSITE of the door jamb.

See Figure 2 for CORRECT

placement.

(Never put the bumper/spacers on the door jamb side of the

bracket as this may prevent the door from properly closing.)

See Figure 3 for

INCORRECT placement.

If the bumper/spacers are not needed, simply install the plain brackets as is to the

top of your door. See Figure 4

Once the top brackets are installed, slide the remaining 2 brackets onto the bottom

of your door. See Figure 5.

Hold the High Rise from its top two straps and hook the clips at the end of the

straps onto the top two brackets. See Figure 6.

Once the High Rise is hanging from the top two brackets, hook the bottom two

clips to the lower two brackets. Pull the cinch strap lightly on the right and left

side just enough to slightly tighten the brackets to the underside of the door.

See Figure 7.

At this time, adjust the top and bottom brackets to the correct width apart

so the High Rise hangs straight and is centered on the door. Step back

and adjust the top, and/or bottom. Be sure it is visually straight and

where you want it. Lastly, rmly pull down on each cinch strap to secure

the Hangin’ High Rise to the door. Figure 8

shows a good visual of

correct positioning of the bottom brackets and how the straps should

look once cinched securely to the door.

The K&H 5 Story Hangin’ High Rise will now keep your cats

busy for hours with plenty of places to play, hide, and lounge for years

to come. And don’t forget its space-saving benets!

ASSEMBLY & INSTALLATION INSTRUCTIONS:

K&H Pet Products with design is a registered trademark of Central Garden & Pet Company.

CORRECT

DOOR JAMB

BUMPER/

SPACER

BUMPER/

SPACER

INCORRECT

Figure 7

Care Instructions: When the 5 Story Hangin’ High Rise is

removed from packaging it is safe to steam in order to remove

unwanted wrinkles. To clean, wipe with a damp cloth.

K&H Hangin’ Cat Condo / Hangin’ High Rise Cat Tree User manual

Brand: K&H

Model: Hangin’ Cat Condo / Hangin’ High Rise Cat Tree

Type: User manual

Download PDF

report

K&H Hangin’ Cat Condo / Hangin’ High Rise Cat Tree User manual

K&H Hangin’ Cat Condo / Hangin’ High Rise Cat Tree User manual

Related papers

Other documents