Anybus AB7507 Installation guide

Anybus
Brand
Anybus
Model
AB7507
Type
Installation guide
Anybus X-gateway - CC-Link IE Field™ Slave Interface Network Installation Sheet
www.anybus.comSP1736, rev. 2.00, Apr 2015
Accessories Checklist
The following items are required for installation:
• USB cable (included)
• LAN cable (not included)
Installation and Startup Summary
1. Set a valid node number.
2. Connect the gateway to the network.
3. Connect a PC to the gateway via USB (optional).
4. Power up and (if required) confi gure the gateway.
LED Indicators
LED Indication Meaning
GW Status See Gateway Installation Sheet
RUN Green Normal operation
Off No network, or timeout
ERROR
Red Station not operating normally, illegal
station number, parameter error
Red (blinking) Link error
Off Normal operation (or no power)
LINK 2 (X1.2/X2.2)
(if switch 8 = ON)
Green Link established
Green (fl ashing) Transmitting/receiving data
Off Link not detected
RDLED
(if switch 8 = OFF)
Green Data received
Off No data received (or no power)
LINK 1 (X1.1/X2.1)
(if switch 8 = ON)
Green Link established
Green (fl ashing) Transmitting/receiving data
Off Link not detected
SDLED
(if switch 8 = OFF)
Green Data transmitted
Off No data transmitted (or no power)
Product Overview
The CC-Link IE Field slave interface can be top- or bottom-mounted.
Both of these options are illustrated below.
Top-mounted Interface
ON
1 2 3 4 5 6 7 8
Configuration Switches
CC-Link IE Field Connectors
Power Connector (X3)
(X1.1) (X1.2)
Bottom-mounted Interface
ON
12345678
Configuration Switches
CC-Link IE Field Connectors
(X2.1) (X2.2)
CC-Link IE Field Connector
Pin Signal
18
1 TD+
2 TD-
3 RD+
4, 5, 7, 8 Termination to PE
6 RD-
Confi guration Switches
Switches 1 to 7 are used to set the node number using binary nota-
tion. Changes will take effect after restarting the gateway.
DIP Switches 1 to 7
0 Reserved – ERROR LED shows red.
1–120 Node number setting (switch 1 = LSB, switch 7 = MSB)
121–126 Invalid node number – no communication, ERROR LED shows red.
127 Node number assigned from mailbox message if available,
otherwise ERROR LED shows red.
Switch 8 determines the function of the last two LED:s in each column
(top or bottom interface). Changes will take effect immediately.
DIP Switch 8
ON LED:s indicate link status (LINK 2/LINK 1)
OFF LED:s indicate data transmission (RD/SD) (default setting)
Example:
ON
LSB MSB
12345678 Node number = 86 (2+4+16+64)
LED:s show LINK status (switch 8 ON)
Technical Support
Technical support, documentation and software downloads are
available at www.anybus.com.
Top-mounted
GW Status
USB
(X4)
USB
(X4)
B
otto
m-m
ou
n
ted
RUN
ERROR
RD / LINK 2 (X1.2)
SD / LINK 1 (X1.1)
GW Status
RUN
ERROR
RD / LINK 2 (X2.2)
SD / LINK 1 (X2.1)
  • Page 1 1

Anybus AB7507 Installation guide

Anybus
Brand
Anybus
Model
AB7507
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents