2. HOMDOX
  3. 55 Digital Parrot Egg Incubator Auto Turning
55 Digital Parrot Egg Incubator Auto Turning

HOMDOX 55 Digital Parrot Egg Incubator Auto Turning User manual

  • Hello! I am an AI chatbot trained to assist you with the HOMDOX 55 Digital Parrot Egg Incubator Auto Turning User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
About Water Hole
Egg Incubator
User Manual
Fig.1
8
1. Add water to the incubator through the water hole with water
dropper to maintain the humidity as shown (Fig. 1).
2. Excessive water will overflow from the water hole as well.
2
Safety Instructions
1. Voltage applied should match the rated voltage of this appliance.
2. Ensure that the eggs are clean as poor hygiene could lead to
failed incubation.
3. Do not open the lid frequently when the incubator is working.
4. Before you use the incubator on hatching, run it for 24 hours in
advance for warm-up.
5. Set the egg with the pointy side down.
6. Don’t place the incubator in environment which is too
well-ventilated as the heating temperature might be affected.
7. Water added should not spill out of the water groove of incubator.
8. Please add or reduce water according to the indicative humidity.
9. Use a piece a dry cloth or sponge to absorb the excessive water if
needed.
10. Ensure that water is added before turning on the device.
11.
Egg Incubator x 1
Plastic Cover x 1
Power Cord x 1
Water Dropper x 1
If the temperature reading on the display panel is different from
the actually one, you can calibrate the readings.
(1) Press and hold “Set” button for 3 seconds.
(2) Press “+” or “-” button to select “CA”.
(3) Press “Set” button once.
(4) Press “+” or “-” button to adjust the temperature reading.
(5) Press “Set” button to confirm.
6. Setting Desired Temperature Upper and Lower Limit (HS and LS)
Upper Temperature Limit (HS)
(1) Press and hold “Set” button for 3 seconds.
(2) Press “+” or “-” button to select “HS”.
(3) Press “Set” button once.
(4) Press “+” or “-” button to adjust the upper temperature limit.
(5) Press “Set” button to confirm.
Lower Temperature Limit (LS)
(1) Press and hold “Set” button for 3 seconds.
(2) Press “+” or “-” button to select “LS”.
(3) Press “Set” button once.
(4) Press “+” or “-” button to adjust the lower temperature limit.
(5) Press “Set” button to confirm.
7. Factory Reset
1. Keep pressing the “Reset” button and unplug the power cord.
2. Don’t release the “Reset” button and reconnect the power,
wait for the machine to start up.
3. The display panel will start counting down. After the
count-down, the factory reset will be finished.
NOTE:
Generally, it would take 18 days for the chicken to hatch out. Remove
the egg turner on the 18th day and the chicken will hatch out from 19th
to 21st days. Please note that the time indicated above will vary
according to the kinds of eggs.
7
Specifications
Overall Dimensions
(L x W x H)
19 1/8” x 18 3/16” x 8 1/4”
(48.5 x 46.2 x 21 cm)
Voltage
230 V(UK) / 110 V(USA)/195 to 245 V(AU)
Power
100 W(UK)/100 W(USA)/ 100 W (AU)
Temperature Range
86 to 103 ℉(30 to 39.5℃）
Operation Instructions
6
3
2. Setting Temperature
(1) Press “Set” Button once.
(2) Press “+” or “-” button to select the desired temperature.
(3) Press “Set” to confirm.
3. Setting Temperature Alarm Range (AL and AH)
The machine will alarm when the temperature is over or below the
alarm temperature range. The high alarm temperature range is the
sum of the setting temperate and the value of AH. The low alarm
temperature range is the setting temperature subtracting the value
of AL.
For example, if we set the temperature at 37 ℃ and AH at 1 ℃, the
appliance will alarm if its temperature reaches over 38℃. Similarly, if
we set the temperature at 37 ℃ and AL at 1 ℃, the appliance will
alarm if its temperature decreases below 36℃.
Low Temperature Alarm Range (AL)
(1) Press and hold “Set” button for 3 seconds.
(2) Press “+” or “-” button to select “AL”.
(3) Press “Set” button once.
(4) Press “+” or “-” button to adjust the low temperature alarm
range.
(5) Press “Set” button to confirm.
High Temperature Alarm Range (AH)
(1) Press and hold “Set” button for 3 seconds.
(2) Press “+” or “-” button to select “AH”.
(3) Press “Set” button once.
(4) Press “+” or “-” button to adjust the high temperature alarm
range.
(5) Press “Set” button to confirm.
4. Setting Humidity Alarm Parameter (AS)
(1) Press and hold “Set” button for 3 seconds.
(2) Press “+” or “-” button to select “AS”.
(3) Press “Set” button once.
(4) Press “+” or “-” button to adjust the humidity alarm parameter.
(5) Press “Set” button to confirm.
5. Calibrating Temperature Sensor Reading (CA)
1
The yellow egg turner has already installed into the incubator when
leaving factory. Please ensure that the egg turner has been put in place in
the incubator in case of misplacement during delivery.
The round motor must
be in place as shown.
4 corners of egg turner slot
in the incubator bottom.
4
2
Install the plastic cover on the incubator as shown above.
Connect the power cord to the incubator.
3
Operation Panel
Operation Instructions
Display Panel
Egg Turning Countdown Time
Hatching
Days
Temperature
Light
Heating
Humidity
Low Humidity Warning
Fan
1. Connect the power cord to a power outlet. Press the “ON/OFF”
button to turn on the incubator. There will be “beep” sound
warning that the humidity is low. Please ignore it and press any
one button on the operation panel to stop the sound.
5
/