DeWalt DW099 User manual

Brand: DeWalt

Model: DW099

Category: Laser levels

Type: User manual

INSTRUCTION MANUAL

GUIDE D'UTILISATION

MANUAL DE INSTRUCCIONES

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA

DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO

ANTES DE USAR EL PRODUCTO.

DEWALT Industrial Tool Co., 701 Joppa Road, Baltimore, MD 21286

EWALT

The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme; the

“D” shaped air intake grill; the array of pyramids on the handgrip; the kit box configuration; and the array of

lozenge-shaped humps on the surface of the tool.

DW099 3-Beam Laser Level

Niveau laser à 3 faisceaux DW099

Nivel láser de 3 rayos DW099

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL,

CALL US TOLL FREE AT: 1-800-4-DEWALT (1-800-433-9258)

Safety Instructions for Lasers

WARNING! Read and understand all instructions. Failure to follow all instruc-

tions listed below may result in electric shock, fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

WARNING! Laser Radiation Exposure. Do not disassemble or modify the laser level.

There are no user serviceable parts inside. Serious eye injury could result.

WARNING: Hazardous Radiation. Use of controls or adjustments or performance of proce-

dures other than those specified herein may result in hazardous radiation exposure.

• Do not operate the laser in explosive atmospheres, such as in the presence of flam-

mable liquids, gases, or dust. Lasers create sparks which may ignite the dust or fumes.

• Use the laser only with the specifically designated batteries. Use of any other batteries

may create a risk of fire.

• Store idle laser out of reach of children and other untrained persons. Lasers are

dangerous in the hands of untrained users.

• Use only accessories that are recommended by the manufacturer for your model.

Accessories that may be suitable for one laser, may create a risk of injury when used on

another laser.

• Tool service must be performed only by qualified repair personnel. Service or mainte-

nance performed by unqualified personnel may result in injury. To locate your nearest

WALT service center call 1-800-4-DEWALT (1-800-433-9258) or go to

http://www.dewalt.com on the Internet.

• Do not use optical tools such as a telescope or transit to view the laser beam. Serious

eye injury could result.

• Do not place the laser in a position which may cause anyone to intentionally or

unintentionally stare into the laser beam. Serious eye injury could result.

• Turn the laser off when it is not in use. Leaving the laser on increases the risk of staring

into the laser beam.

• Do not disassemble the laser tool. There are no user serviceable parts inside.

• Do not modify the laser in any way. Modifying the tool may result in Hazardous Laser

Radiation Exposure.

• Do not operate the laser around children or allow children to operate the laser. Serious

eye injury may result.

• Do not remove or deface warning labels. Removing labels increases the risk of exposure

to radiation.

• Position the laser securely on a level surface. Damage to the laser or serious injury could

result if the laser falls.

• The label on your tool may include the following symbols.

V ............................volts

mW ........................milliwatts

................laser warning symbol

nm ..........................wavelength in nanometers

II..............................Class II Laser

IIIa ..........................Class IIIa Laser

WARNING LABELS

For your convenience and safety, the following label is on your laser.

CAUTION: LASER RADIATION - DO NOT STARE INTO BEAM. CLASS II LASER

PRODUCT.

CAUTION: CLASS 2 LASER RADIATION WHEN OPEN DO NOT STARE INTO THE

BEAM.

Laser Information

The DW099 laser level is a class 2 laser product and complies with 21 CFR 1040.10 and

1040.11 except for deviations pursuant to laser notice No. 50, dated July 26, 2001.

INTRODUCTION

The DW099 3-Beam Laser Level is a manual-leveling laser tool that can be used inside and out-

side for horizontal (level), vertical (plumb), and square alignment projects. This tool comes fully

assembled (batteries not included). This tool has been designed with features that allow

for quick and easy set-up. Please read and understand all instructions within this instruction

manual prior to use.

General Safety Rules For Battery Operated Tools

WARNING! Read and understand all instructions. Failure to follow all instruc-

tions listed below may result in electric shock, fire and/or serious personal injury.

WORK AREA

• Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.

• Do not operate power tools in explosive atmospheres, such as in the presence of flam-

mable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes.

• Keep bystanders, children, and visitors away while operating a power tool. Distractions

can cause you to lose control.

ELECTRICAL SAFETY

• Use battery operated tool only with the specifically designed batteries. Use of any other

batteries may create a risk of fire.

Battery

This tool is powered by three AA size batteries.

To install batteries:

1. Before installing batteries, ensure that the ON/OFF button is in the OFF position (button fully

extended to prevent beam from coming on while inserting batteries).

2. Refer to the label on the laser to open battery compartment.

3. Insert three fresh AA batteries in the compartment, placing the battery polarity

(+ and –)

according to the label on the battery compartment.

WARNING: Batteries can explode, or leak, and can cause injury or fire. To reduce this risk:

• Carefully follow all instructions and warnings on the battery label and package.

• Always insert batteries correctly with regard to polarity (+ and –), marked on the battery

and the equipment.

• Do not short battery terminals.

• Do not charge batteries.

• Do not mix old and new batteries. Replace all of them at the same time with new batteries

of the same brand and type.

• Remove dead batteries immediately and dispose of per local codes.

• Do not dispose of batteries in fire.

• Keep batteries out of reach of children.

• Remove batteries if the device will not be used for several months.

PERSONAL SAFETY

• Stay alert, watch what you are doing and use common sense when operating a laser.

Do not use laser while tired or under the influence of drugs, alcohol, or medication. A

moment of inattention while operating lasers may result in serious personal injury.

• Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair,

clothing, and gloves away from moving parts. Loose clothing, jewelry, or long hair can be

caught in moving parts. Air vents often cover moving parts and should also be avoided.

• Do not overreach. Keep proper footing and balance at all times. Proper footing and balance

enables better control of the tool in unexpected situations.

• Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes,

hard hat, or hearing protection must be used for appropriate conditions.

TOOL USE AND CARE

• Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled with

the switch is dangerous and must be repaired.

• Store idle tools out of reach of children and other untrained persons. Tools are

dangerous in the hands of untrained users.

• Use only accessories that are recommended by the manufacturer for your model.

Accessories that may be suitable for one tool, may become hazardous when used on

another tool.

SERVICE

• Tool service must be performed only by qualified repair personnel. Service or mainte-

nance performed by unqualified personnel could result in a risk of injury.

• When servicing a tool, use only identical replacement parts. Follow instructions in the

Maintenance section of this manual. Use of unauthorized parts or failure to follow

Maintenance Instructions may create a risk of electric shock or injury.

To locate your nearest DEWALT service center call 1-800-4-DEWALT (1-800-433-9258) or go to

http://www.dewalt.com on the Internet.

Operating Tips

• Use only new, high-quality, name brand batteries for best results.

• Ensure batteries are in good working condition.

• To extend battery life, turn laser off when not working with or marking the beam.

• To ensure the accuracy of your work, check to make sure your laser is calibrated often. (See

Field Calibration Check.)

• Before attempting to use the laser, make sure it is positioned securely, on a smooth, flat

surface.

• Always mark the center of the dot or pattern created by the laser.

• Extreme temperature changes may cause movement of internal parts that can affect

accuracy. Check your accuracy often while working. (See Field Calibration Check.)

• If the laser has been dropped, check to make sure your laser is calibrated. (See Field

Calibration Check.)

OPERATION

To Turn the Laser On and Off

1. With the laser off, place it on a flat surface or leveling base (included). Press the ON/OFF

button to power the laser ON. The laser will turn on and project three beams; one up (A) and

two square, level beams (B, C) (Fig. 1).

2. Press the ON/OFF button again. The laser will then turn off and no laser beams will be

projected.

Using the Laser

The beams are level or plumb as long as the calibration has been checked. (See Field

Calibration Check.) The laser can be used to level, plumb and square points using any

combination of the three beams. (See Leveling the Laser.)

NOTE: The laser has magnets which can be used to help position the tool against steel

surfaces. Always make sure the tool is positioned securely and on a smooth surface.

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-DEWALT • www.dewalt.com

USING THE LASER WITH ACCESSORIES

The laser is equipped with a 1/4" x 20 female thread on the bottom of the unit. This thread is to

accommodate current or future D

EWALT accessories. Only use DEWALT accessories specified

for use with this product. Follow the directions included with the accessory.

CAUTION: The use of any other accessory not recommended for use with this tool could be

hazardous.

If you need any assistance in locating any accessory, please contact DEWALT Industrial Tool

Co., 701 East Joppa Road, Baltimore, MD 21286 or call 1-800-4-D

EWALT (1-800-433-9258).

See our catalog on the World Wide Web at www.dewalt.com.

LEVELING THE LASER

To manually level this tool, secure the laser to the leveling base provided and adjust the leveling

knobs (D) until the bubbles in the vials (E) are centered.

MAINTENANCE

To maintain the accuracy of your work, check the laser often to make sure it is properly

calibrated. See Field Calibration Check.

Calibration checks and other maintenance repairs may be performed by D

EWALT service

centers.

When not in use, store the laser in a safe place. Do not store your laser at temperatures below

-5˚F (-20˚C) or above 140˚F (60˚C).

Do not store your laser when wet. The laser should be dried first with a soft dry cloth.

Cleaning

Exterior plastic parts may be cleaned with a damp cloth. Although these parts are solvent resis-

tant, NEVER use solvents. Use a soft dry cloth to remove moisture from the tool before storage.

Field Calibration Check

CHECKING ACCURACY – LEVEL (FIG. 3–6)

Checking the level accuracy of the laser unit requires two parallel walls at least 25' (7.7m) apart.

It is important to conduct a calibration check using a distance no shorter than the distance of the

applications for which the tool will be used.

1. Place the unit 2"–3" (5–8cm) from the first wall, facing the wall (Fig. 3).

2. Level the laser unit as necessary to center the bubble vials (E).

3. Mark the beam position (a) on the first wall.

4. Turn the unit 180° and level the laser unit.

5. Mark the beam position (b) on the second wall (Fig. 4).

6. Place the unit 2"–3" (5–8cm) from the second wall, facing the wall (Fig. 5).

7. Adjust the height and level the laser until the beam hits the mark at position (b).

8. Turn the unit 180° and aim the beam near the mark on the first wall from Step 3 (Fig. 6).

9. Level the laser unit and mark beam position (c).

10. The distance between marks (a) and (c) is the error:

CHECKING ACCURACY – PLUMB (FIG. 7)

Checking the plumb accuracy of the laser unit can be done most accurately when there is a

substantial amount of vertical height available, ideally 25' (8m). Use one person on the floor to

position the laser unit and another near a ceiling to mark the dot created by the laser as shown

in Figure 7. It is important to conduct a calibration check using a distance no shorter than the

distance of the applications for which the tool will be used.

1. Start by drawing an X on the floor.

2. Place the laser unit on the floor such that the vertical beam is directly above the X.

3. Center the two active bubble vials (E) to level the unit.

4. Mark the center (F) of the dot on the ceiling created by the plumb beam.

5. Turn the unit 180° and position it again above the X mark.

6. Level the laser unit.

7. Mark the center (G) of the dot on the ceiling created by the plumb beam.

The two marks on the 25' (8m) high ceiling should be no more than 1/2" (12.5mm) apart. If

the vertical distance from floor to ceiling is much less than 25' (8m), then the marks should

be closer. For example, if the height of the ceiling is 12.5', then the marks should be 1/4"

(6.5mm) apart.

Checking Level to Square Beam 90˚ Accuracy (Fig. 8)

Refer to the graphic for the location of the DW099 at each step and for the location of the marks

made at each step. All marks can be made on the floor by placing a target in front of the level

or square beam and transferring the location to the floor.

1. Find a room at least 35' (10m) long. Mark a point (H) on the floor at one end of the room.

2. Set up the laser so that its plumb beam is over point (H). Make sure the level beam points

toward the far end of the room.

3. Mark a point (I) on the floor at the center of the room using a target to transfer the level beam

location to the floor.

4. Mark a point (J) on the far wall or transfer the level beam location to the floor.

5. Move the laser to point (I) and align the level beam to point (J) again.

6. Mark the location of the square beam (K) on the floor.

NOTE: To ensure accuracy, the distances from H to I, I to J, and I to K should be equal.

7. Turn the laser 90° so that the level beam aligns with point K.

8. Mark the location of the square beam (L) on the floor as close as possible to point (H).

9. Measure the distance between points (H) and (L). If the measurement is greater than the

values indicated, the laser is out of squareness.

Troubleshooting

THE LASER DOES NOT TURN ON

• Make sure batteries are installed according to the label in the battery compartment.

• Make sure the batteries are in proper working condition. If in doubt, try installing new

batteries.

• Make sure that the battery contacts are clean and free of rust or corrosion. Be sure to keep

the laser level dry and use only new, high-quality, name brand batteries to reduce the

chance of battery leakage.

• If the laser unit is heated above 120˚F (50˚C), the unit will not turn on. If the laser has been

stored in extremely hot temperatures, allow it to cool. The laser level will not be damaged by

pressing the on/off button before cooling to its proper operating temperature.

Service and Repairs

NOTE: Disassembling the laser level will void all warranties on the product.

To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be

performed by authorized service centers. Service or maintenance performed by unqualified

personnel may result in a risk of injury. To locate your nearest D

EWALT service center call

1-800-4-D

EWALT (1-800-433-9258) or go to http://www.dewalt.com on the Internet.

Distance The 90° angle between the level

between beam and square beam is out of

points H and I calibration if the distance between

points H and L is:

17.5' (5m) 3/16" (4.5mm)

35' (10m) 3/8" (9mm)

Distance Between Walls Allowable Error

25' (7.7m) 5/32" (4mm)

50' (15.4m) 5/16" (8.5mm)

75' (23m) 15/32" (12.5 mm)

100' (30.8m) 5/8" (17mm)

FIG. 1

FIG. 2

25'

FIG. 3

FIG. 4

FIG. 6

FIG. 7

FIG. 5

FIG. 8

Steps / Étapes /

Pasos 1, 2

Steps

Étapes

Pasos

3, 5

Step / Étape / Paso 4

Step / Étape /

Paso 6

Step / Étape / Paso 8

Step

Étape

Paso

Step / Étape / Paso 9

17.5'

(5m)

17.5'

(5m)

17.5' (5m)

Page is loading ...

DeWalt DW099 User manual

Brand: DeWalt

Model: DW099

Category: Laser levels

Type: User manual

Download PDF

report

in other languages

français: DeWalt DW099 Manuel utilisateur
español: DeWalt DW099 Manual de usuario

DeWalt DW099 User manual

DeWalt DW099 User manual

in other languages

Related papers

Other documents