Tyan GT20 (B5502) User manual

http://www.tyan.com

1

TYAN GT20

B5502

Service Engineer’s Manual

2

http://www.tyan.com

PREFACE

Copyright

This publication, including all photographs, illustrations, and software, is

Neither this manual, nor any material contained herein, may be reproduced

without written consent of manufacturer.

TYAN

®

is a

registered trademark of MiTAC International Corporation.

Version 1.0

Disclaimer

Information contained in this document is furnished by MiTAC International

Corporation and has been reviewed for accuracy and reliability prior to printing.

MiTAC assumes no liability whatsoever, and disclaims any express or implied

warranty, relating to sale and/or use of TYAN

®

products including liability or

warranties relating to fitness for a particular purpose or merchantability. MiTAC

retains the right to make changes to produce descriptions and/or specifications

at any time, without notice. In no event will MiTAC be held liable for any direct or

indirect, incidental or consequential damage, loss of use, loss of data or other

malady resulting from errors or inaccuracies of information contained in this

document.

Trademark Recognition

All registered and unregistered trademarks and company names contained in

this manual are property of their respective owners including, but not limited to

the following.

TYAN

®

is a trademark of MiTAC International Corporation.

Intel

®

is a trademark of Intel

®

Corporation.

AMI

®

, AMIBIOS

®

and combinations thereof are trademarks of AMI Technologies.

Microsoft

®

, Windows

®

are trademarks of Microsoft Corporation.

IBM

®

, PC

®

, AT

®

and PS/2

®

are trademarks of IBM Corporation.

Winbond

®

is a trademark of Winbond Electronics Corporation.

3

http://www.tyan.com

Federal Communication Commission (FCC)

Notice for the USA

Compliance Information Statement (Declaration of

Conformity Procedure) DoC FCC Part 15: This

device complies with part 15 of the FCC Rules

Operation is subject to the following conditions:

1. This device may not cause harmful interference;

2. This device must accept any interference received including interference

that may cause undesired operation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try one or

more of the following measures:

z Reorient or relocate the receiving antenna.

z Increase the separation between the equipment and the receiver.

z Plug the equipment into an outlet on a circuit different from that of

the receiver.

Consult the dealer on an experienced radio/television technician for help.

Notice for Canada

This apparatus complies with the Class A limits for radio interference as

specified in the Canadian Department of Communications Radio Interference

Regulations. (Cet appareil est conforme aux norms de Classe A d’interference

radio tel que specifie par le Ministere Canadien des Communications dans les

reglements d’ineteference radio.)

Notice for Europe (CE Mark)

This product is in conformity with the Council

Directive 89/336/EEC, 92/31/EEC (EMC).

CAUTION: Lithium battery included with this board. Do not puncture, mutilate, or

dispose of battery in fire. There will be danger of explosion if battery is incorrectly

replaced. Replace only with the same or equivalent type recommended by

manufacturer. Dispose of used battery according to manufacturer instructions

and in accordance with your local regulations.

4

http://www.tyan.com

About this Manual

This manual provides you with instructions on installing your TYAN GT20-B5502.

This Manual is intended for experienced users and integrators with hardware

knowledge of personal computers.

This manual consists of the following parts:

Chapter1:

Provides an introduction to the TYAN GT20-B5502 barebones,

standard parts list, describes the external components, gives a

table of key components, and provides block diagram of the

system.

Chapter2:

Covers procedures on installing the CPU, memory modules and

hard drives.

Chapter3:

Covers removal and replacement procedures for pre-installed

components.

Appendix:

List the cable connection and FRU part tables for reference of

system setup, and technical support in case a problem arises

with your system.

For information on the motherboard, please refer to the attached motherboard

user’s manual. You can find the detailed description about jumper and BIOS

settings from the motherboard manual.

5

http://www.tyan.com

SAFETY INFORMATION

Before installing and using TYAN GT20-B5502, take note of the following

precautions:

·Read all instructions carefully.

·Do not place the unit on an unstable surface, cart, or stand.

·Do not block the slots and opening on the unit, which are provided for

ventilation.

·Only use the power source indicated on the marking label. If you are not

sure, contact the power company.

·The unit uses a three-wire ground cable, which is equipped with a third

pin to ground the unit and prevent electric shock. Do not defeat the

purpose of this pin. If you outlet does not support this kind of plug, contact

your electrician to replace your obsolete outlet.

·Do not place anything on the power cord. Place the power cord where it

will not be in the way of foot traffic.

·Follow all warnings and cautions in this manual and on the unit case.

·Do not push objects in the ventilation slots as they may touch high

voltage components and result in shock and damage to the components.

· When replacing parts, ensure that you use parts specified by the

manufacturer.

·When service or repairs have been done, perform routine safety checks

to verify that the system is operating correctly.

·Avoid using the system near water, in direct sunlight, or near a heating

device.

·Cover the unit when not in use.

6

http://www.tyan.com

Table of Contents

Chapter 1: Overview.........................................................................9

1.1 About the TYAN GT20-B5502 .................................................. 9

1.2 Features.................................................................................. 10

1.3 Product Models....................................................................... 13

1.4 Standard Parts List ................................................................. 14

1.4.1 Box Contents ................................................................... 14

1.4.2 Accessories ..................................................................... 15

1.5 About the Product................................................................... 16

1.5.1 System Front View........................................................... 16

1.5.2 System Rear View ........................................................... 16

1.5.3 LED Definitions ................................................................ 17

1.5.4 Motherboard (S5502) Layout........................................... 19

1.5.5 Jumpers & Connectors .................................................... 20

1.5.6 System Block Diagram .................................................... 21

1.5.7 Internal View .................................................................... 22

Chapter 2: Setting Up..................................................................... 23

2.0.1 Before you Begin ............................................................. 23

2.0.2 Work Area........................................................................ 23

2.0.3 Tools ................................................................................ 23

2.0.4 Precautions...................................................................... 24

2.1 Installing Motherboard Components....................................... 25

2.1.1 Removing the Chassis Cover .......................................... 25

2.1.2 Installing the CPU and Heatsink...................................... 26

2.1.3 Installing the Memory....................................................... 30

2.1.4 Installing Hard Drives....................................................... 34

2.1.5 Installing the PCI-E Cards ............................................... 36

2.2 Rack Mounting........................................................................ 38

2.2.1 Installing the Server in a Rack......................................... 38

7

http://www.tyan.com

2.2.2 Installing the inner Rails to the Chassis........................... 39

2.2.3 Installing the Outer Rails to the Rack .............................. 40

2.2.4 Rack mounting the Server ............................................... 42

Chapter 3: Replacing Pre-Installed Components ........................ 45

3.1 Introduction ............................................................................. 45

3.2 Disassembly Flowchart........................................................... 45

3.3 Removing the Cover............................................................... 47

3.4 Replacing Motherboard Components..................................... 47

3.4.1 Replacing Expansion Card .............................................. 47

3.4.2 Disconnecting All Motherboard Cables ........................... 49

3.4.3 Removing the Motherboard ............................................. 50

3.5 Replacing the LED Control Board .......................................... 51

3.5.1 M1008 LED Control Board Features ............................... 53

3.5.2 M1008 LED Control Board Connector Pin Definition ...... 53

3.6 Replacing the System Fan ..................................................... 54

3.7 Replacing the M1232 HDD Backplane Board ........................ 57

3.7.1 M1232 HDD Backplane Board Features ......................... 59

3.7.2 M1232 Connector Pin Definitions .................................... 61

Appendix I: Cable Connection Tables ..........................................65

Appendix II: FRU Parts Table ........................................................67

Appendix III: Technical Support....................................................69

http://www.tyan.com

8

NOTE

9

http://www.tyan.com

Chapter 1: Overview

1.1 About the TYAN GT20-B5502

Congratulations on the purchase of the TYAN GT20-B5502, a highly optimized

rack mount barebone system. The GT20-B5502 is designed to support (1) Intel

®

Xeon 3400 Series processor and up to 32GB RDIMM or 16GB UDIMM

DDR3-800/1066/1333 memory per node. Utilizing advanced technology from

Intel

®

, the GT20-B5502 system provides scalable 32/64-bit computing, high

bandwidth memory design, and lightning-fast PCI-E bus capabilities. The

GT20-B5502 not only manages today’s IT environments, but also flexibility for

future application usage.

TYAN

®

also offers the GT20-B5502 in a version that can support up to four

hot-swap hard drives. The GT20-B5502 uses latest chassis designs which

features a solid mechanical enclosure and robust features. All of this provides

the GT20-B5502 with the power and flexibility to meet the needs of today’s

server applications.

http://www.tyan.com

10

1.2 Features

TYAN GT20B5502 (B5502G20V4H-LE)

Form Factor

1U Rackmount

Chassis Model

GT20

Dimension (D x W x

H)

25.4" x 17.2" x 1.72" (645 x 436 x 43.6mm)

Motherboard

S5502GM2NR-LE

Board Dimension

ATX, 12"x9.6" (305x243.8mm)

System

Gross Weight

15.96Kg

Buttons

(1) PWR / (1) RST / (1) NMI / (1) ID

LEDs

(1) PWR / (1) ID / (1) Warning / (3) LAN / (1) BMC

Front Panel

I/O Ports

(2) USB ports

Type / Q'ty

3.5" Hot-Swap / (4)

External Drive

Bay

Supported HDD

Interface

SATA-II 3.0Gb/s

System Cooling

Configuration

FAN

(4) 4cm fans

Type

EPS1U

Efficiency

PFC / 80-plus

Input Range

Full-range AC(100-240V)

Frequency

60 Hertz

Power Supply

Output Watts

400 Watts

Supported CPU

Series

Intel Xeon Processors 3400 Series

Processor

Socket Type / Q'ty

LGA 1156/ (1)

11

http://www.tyan.com

Thermal Design

Power (TDP)

wattage

Max up to 95W

PCH

Intel 3420

Chipset

Super I/O

Winbond W83627

Supported DIMM

Qty

(6) DIMM slots

DIMM Type / Speed

DDR3 800/1066/1333* RDIMM/UDIMM / * limit 1

per channel for 1333MHz speed

Capacity

Up to 32GB RDIMM/ 16GB UDIMM

Memory channel

2 Channels / Support 2 UDIMMs or 3 RDIMMs

per channel

Memory

Memory voltage

1.5V

PCI-E

(1) PCI-E Gen.2 x16 slot

Expansion Slots

Pre-install TYAN

Riser Card

M2091, PCI-E x16 1U riser card (left)

Port Q'ty

(2)

LAN

Controller

Intel 82574L

Connector type

D-Sub 15-pin

Resolution

1600x1200@60Hz

Graphic

Chipset

Aspeed AST2050

USB

(4) ports (2 at front, 2 at rear)

COM

(1) DB-9 COM port

PS/2

(1) PS/2 connector (for Keyboard and Mouse)

VGA

(1) D-Sub 15-pin port

I/O Ports

RJ-45

(2) ports

12

http://www.tyan.com

Chipset

Winbond W83793G

Voltage

Monitors voltage for CPU, memory, chipset &

power supply

Temperature

Monitors temperature for CPU & system

environment

LED

Fan fail LED indicator / Over temperature warning

indicator

System

Monitoring

Others

Chassis intrusion detection / Watchdog timer

support

Onboard Chipset

Onboard Aspeed AST2050

AST2050 IPMI

Feature

IPMI 2.0 compliant baseboard management

controller (BMC) / Supports storage over IP and

remote platform-flash / BIOS update

Server

Management

AST2050 iKVM

Feature

24-bit high quality video compression / Dual

10/100 Mb/s MAC interfaces

Brand / ROM size

AMI / 4MB

BIOS

Feature

Plug and Play (PnP) /PCI2.3 /WfM2.0

/SMBIOS2.3 /PXE boot / ACPI 2.0 power

management /Power on mode after power

recovery / User-configurable H/W monitoring /

Auto-configurable of hard disk types

Operating

System

OS supported list

Please visit our Web site for the latest update.

FCC (DoC)

Class A

CE (DoC)

Yes

C-Tick

Yes

Regulation

VCCI

Yes

13

http://www.tyan.com

Operating Temp.

10° C ~ 35° C (50° F~ 95° F)

Non-operating

Temp.

- 40° C ~ 70° C (-40° F ~ 158° F)

Operating

Environment

In/Non-operating

Humidity

90%, non-condensing at 35° C

RoHS RoHS 6/6 Complaint

Yes

Barebone

(1) GT20-B5502 Barebone

Manual

(1) Quick Ref. Guide / (1) MB User's manual + (1)

BB User's manual

Installation CD

(1) TYAN installation CD

Heatsink / Cooler

(1) LGA1156 CPU heatsink

Rail kit

(1) CRAL-0032, sliding rail kit for KGT20

Mounting Ear

(1) CEAR-0050, mounting ear kit for GT20/ GT20

Others

(1) HDD screw pack

Package

Contains

Cable Power Cord

(1) CCBL-0310, US type power cord / (1)

CCBL-0300, EU type power cord

Optional

accessories

Peripheral

(1) CDVD-0060, slim type DVD-ROM

1.3 Product Models

Model HDD Bays Power supply

B5502G20V4H-LE

Hot-swap,

4HDDs

400W single

http://www.tyan.com

14

1.4 Standard Parts List

This section describes GT20-B5502 package contents and accessories. Open

the box carefully and ensure that all components are present and undamaged.

The product should arrive packaged as illustrated below.

1.4.1 Box Contents

Component Description

1U chassis,(4) hot-swap HDDbays

TYAN

®

S5502 system board

(pre-installed)

400W single Power Supply

(4) System FAN

Fan Duct

M1008：

LED control board (pre-installed)

M1232 HDD Board

M2091 PCI-E riser card

http://www.tyan.com

15

1.4.2 Accessories

If any items are missing or appear damaged, contact your retailer or browse to

TYAN

®

’s website for service: http://www.tyan.com

The web site also provides information of other TYAN

®

products, as well as

FAQs, compatibility lists, BIOS settings, etc.

1 x TYAN

®

Motherboard

Drive CD

1 x Heatsink

HDD Screws Mounting Ears & Screws

Barebone Manual Mainboard Manual

AC Power Cord 125V (US)

AC Power Cord 250V

(Europe)

Rail Kit

Rail with Bracket x 2 Screw Pack

http://www.tyan.com

16

1.5 About the Product

The following overview illustrations show you the features of the product.

1.5.1 System Front View

1.5.2 System Rear View

http://www.tyan.com

17

1.5.3 LED Definitions

Front Panel

LED State Color Description

On Green System is turned on

On Green System is under S1 or S3 state

Power

LED

Off Off Power off

Blinking Green LAN active

On Green LAN linked

NIC1

off off LAN not linked

Blinking Green LAN active

On Green LAN linked

NIC2

off off LAN not linked

On Red

Fan fail /Over temperature

/Over voltage

Warning

LED

Off Off No failure

On Blue System identified

ID LED

Off Off System not identified

On Amber PSU fail

Blinking Amber PSU alert

PSMI LED

Off Off No failure

Rear I/O

LAN1/LAN2

LED State Color Description

On Green 10Mb/100Mb/1000Mb linked

Blinking Green 10Mb/100Mb/1000Mb activity

RJ-45

Linkage/

Activity(left)

Off Off No LAN linked

On Amber 1000Mb linked/activity

On Green 100Mb linked/activity

RJ-45

Linkage/

Activity(Right)

Off Off 10Mb mode or No LAN linked

NOTE: “Left” and “Right” are viewed from the rear panel.

http://www.tyan.com

18

ID LED

LED State Color Description

On Blue System identified

ID LED

Off Off System not identified

http://www.tyan.com

19

1.5.4 Motherboard (S5502) Layout

The diagram is representative of the latest board revision available at the time of

publishing. The board you receive may not look exactly like the above diagram.

http://www.tyan.com

20

1.5.5 Jumpers & Connectors

Jumper/Connector Function

J8/J9/J30/J32/J33

4-pin Fan connector

J37/J38/J39/J42

8-pin 4096 fan header

J19/J20

USB Front Panel Header

USB3/USB4

Type-A USB Connectors

J22

TYFP1 Header

J15

COM2 Header

JP4

Clear CMOS Jumper

J41

Chassis Intrusion Jumper

JP1/JP2

COM switch

J2

IPMB Connector

J6

Enable/Disable BMC jumper

J25

PSMI Connector

JP5

Speaker Header

J16

Port80 Header

J23

SAS GPIO to Backplane

J36

PCH SGPIO

J35

2X10_pin FAN connector

J7

LCM Header

Jumper Legend

OPEN - Jumper OFF Without jumper cover

CLOSED - Jumper ON With jumper cover

Page is loading ...

Tyan GT20 (B5502) User manual

This manual is also suitable for

Tyan GT20 (B5502) User manual

Related papers

Other documents