Vents TS-1-90 is an external temperature regulator designed to regulate air temperature inside air ducts and control chimney fans. It features a liquid-filled sensitive element that measures and regulates temperature, with a temperature differential of 40°C and a regulated temperature range of 0°С to +90°С. The thermostat's contacts switch based on temperature increase, making it suitable for use in applications where temperature control is essential.
Vents TS-1-90 is an external temperature regulator designed to regulate air temperature inside air ducts and control chimney fans. It features a liquid-filled sensitive element that measures and regulates temperature, with a temperature differential of 40°C and a regulated temperature range of 0°С to +90°С. The thermostat's contacts switch based on temperature increase, making it suitable for use in applications where temperature control is essential.
EXTERNAL
TEMPERATURE REGULATOR
“VENTS TS-1-90 “
PURPOSE
External temperature regulator TS-1-90, further referred as the thermostat, is applied for
regulation of the air temperature inside the air ducts and control of chimney fans
KAM 125, 140, 150, 160 Eco and KAM 125, 140, 150, 160 EcoDuo T1.
The thermostat contacts are switched as a function of the temperature increase.
The thermostat is designed for installation into the mounting box.
BASIC TECHICAL DATA
Switch contact type: Voltage-free, single-pole, break-make contact
switching voltage 16А, 250 V AC
max.power 500 W
Electrical load type inductive, active
Sensitive element type liquid
0
Temperature differential 4 C
Regulated temperature range 0°С …+90°С
Thermostat overall dimensions 55 х 56 х 56 mm
Capillary tube length 1000 mm
Minimum capillary tube bending radius 5 mm
Temperature probe 6,5 х 95 mm
Operating conditions
Maximum environmenal temperature +80 °С
Relative humidity no more 80%
Maximum capillary tube and probe temperature +150°С
IP protection rating ІР40
Explosive and corrosive admixtures are not allowed in the ambient air.
To connect the thermostat use the fast-on flat terminals, e.g. flatplug 6,3 х 0,8.
DELIVERY SET
The delivery set includes:
thermostat - 1 pce;
control knob;
decorative cover with fastenings;
user's manual;
packing box.
SAFETY PRECAUTIONS
Only a qualified electrical technician is allowed to install the thermostat in compliance with
applicable acting norms and standards.
Warning!
The thermostat is on mains voltage while operating. All the electrical mounting works
shall be performed when the thermostat is disconnected from power supply network.
STORAGE
Store the thermostat in the manufacturer's original packing box in a closed ventilated premise
with the temperature ranging from +5°C to +40°C and the relative humidity less than 80%
(at 25°C)
MANUFACTURER'S WARRANTY
Manufacturer hereby guarantees rated performance of the thermostat within 12 months since
the date of its sale in accordance to the rules of transportation, storage, assembling and operation.
The warranty does not cover mechanically damaged goods. In case of no confirmation of the
sales date the warranty period is calculated from the production date. In case of any failures due
to faulty manufacturing during warranty period, the Customer has the right to have the goods
replaced at the Seller's manufacturing facility.
WARNING!
Manufacturer can not be held responsible for material or physical damages
(includings those related to health of the users) resulting from the unit misuse or gross
mechanical effect. The thermostat user should follow the manual instructions.
ACCEPTANCE CERTIFICATE
The thermostat has been duly certified as serviceable.
Model
“ TS-1-90”
Manufactured on (date):
Trade company name and stamp
Stamp of the acceptance inspector
V60EN-01
Sold
Date of sale:
Ø 28
44
95
Ø 6,5
4,6
M4
Ø 6
6,3
55
2 1
4
С
30
16
50
Ø 42
Ø 56
35
25
5
1
3
2
DESIGN DESCRIPTION
External view and connecting dimensions of the thermostat are shown in fig. 1.
The thermostat consists of the casing 1, decorative cover 2, control knob 3, liquid sensitive
element 4 (temperature probe with the capillary tube).
The temperature is measured and regulated by means of the liquid sensitive element.
The temperature threshold for the thermostat switching ON is set by means of rotating the
control knob. Power for the thermostat is supplied to "C" electrical contact.
If the temperature exceeds the set threshold value the electrical contact "2" is closed thus
turning the fan motor on.
INSTALLATION AND OPERATION GUIDELINES
Install the thermostat on the vertical wall in the flush or external mounting box inside the premise.
avoid any water splashes, rain drops and direct sunshine rays on the thermostat.
Do not install the thermostat directly in the fireplace hood or near other heat sources.
The minimum allowable distance from the thermostat to the heat source, i.e. fireplace hood,
is 1.5 m.
Do not install the thermostat on the flammable material and do not mount it directly
in the firehood place.
fig. 1
THERMOSTAT MOUNTING SEQUENCE
Install the thermostat casing into the mounting box, insert and fix the decorative thermostat
cover by means of the screws, install the control knob. Install and fix the temperature probe
in the air duct.
To connect the thermostat to the electrical power supply network:
disconnect the lead wires from power supply network;
strip the wire leads for 5-7 mm and connect those to the fast-on flat terminals of
"Flatplug 6,3 х 0,8 type.
install the flat plugs on the thermostat contacts against stop.
After connecting the thermostat to power supply network turn the temperature control knob
counter clockwise to set the required turn-on temperature.
fig. 2
where
S1 - automatic switch;
X1 - terminal block;
BK1 - temperature regulator (thermostat)
(S1 is not included into delivery list)
fig. 3
where
S1 - automatic switch;
S2 - thee-position switch;
X1 - terminal block;
BK1 - temperature regulator (thermostat)
(S1 and S2 are not included into delivery list)
Power shall be supplied through the switch integrated into fixed wiring system that opens
all the phases with the clearance between the open contacts no less 3mm at all poles.
The thermostat for the single-speed fan motor models КАМ 125, 140, 150, 160 T1;
КАМ 125, 140, 150, 160 Eco T1 shall be connected to electrical power supply network
following the wiring diagram shown in fig. 2; for double-speed fan motor models
КАМ 125, 140, 150, 160 EcoDuo T1 following the wiring diagram in fig. 3.
The control knob and
decorative cover are not shown.
1
2
3
4
X1
L
N
S1
L
~220V
50Hz
N
PE
2
1
C
T
ВК1
1
2
3
4
X1
H
N
S1
L
~220V
50Hz
N
PE
2
1
C
T
ВК1
L
S2
1
2
max
min
3
-
1
-
2
Vents TS-1-90 is an external temperature regulator designed to regulate air temperature inside air ducts and control chimney fans. It features a liquid-filled sensitive element that measures and regulates temperature, with a temperature differential of 40°C and a regulated temperature range of 0°С to +90°С. The thermostat's contacts switch based on temperature increase, making it suitable for use in applications where temperature control is essential.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Kam Weight Scale User manual
-
Friedrich 2008 User manual
-
Graco 309524L - Viscon High Pressure Fluid Heater User manual
-
-
Reznor EEDU Installation guide
-
Saunier Duval THEMA F SB 23 E Datasheet
-
Samson 2432 Mounting And Operating Instructions
-
Biasi ActivA 12OV, 15OV, 20OV, 25OV User manual
-
Carrier GY User manual
-
Vulcan C24ET10 User manual