Videology 21E20X User manual

Brand
Videology
Model
21E20X
Category
Security cameras
Type
User manual

This manual is also suitable for

06/13/2013 INS-20E20X Rev B
Information may change without notice.
This document provides technical information for the user.
Videology reserves the right to modify the information in
this document as necessary. The customer should make
sure that they have the most recent manual version.
Videology holds no responsibility for any errors that may
appear in this document.
General Description
The 2xE20x is a single color CCD board camera
(32mm x 32mm). It’s small and simple design
allows customers to cost effectively integrate
into various products or equipment like ATM
Machines, Kiosks, Domes, Surveillance
Cameras etc.
Features
• Resolution is 540TVL
• 0.1 Lux Sensitivity
• Small compact board size
• DC Auto Iris capability
• ALC adjustable
• Day/Night mode (optional)
• Variety of CS, M12, M14 lenses
available
Box Contents
1. Camera module
2. Connection cable
Warning
To reduce the risk of fire or electric shock, do
not expose this appliance to rain, water or wet
locations. The camera is not to be mounted
outdoors or in hot, humid or otherwise harsh
environment.
Precautions
• Read and follow these instructions carefully.
• Use a proper UL listed 12V power supply.
• Make sure that no flammable substances get
on the camera. It could cause fire, short-
circuits or damages.
• Be careful when handling the unit.
To prevent damage, do not drop the camera
or subject it to strong shock or vibration.
• Install away from electric or magnetic fields.
• Install away from any heat sources.
• Use proper grounding when handling any
electronic materials.
• Protect from humidity and dust.
• Be careful when installing close to the
ceiling, in a kitchen or boiler room, as the
temperature may rise to high levels.
J3 Connector Settings (back)
ALC Level Control (front)
The 20/21E20X series can operate an auto iris
lens without an external board.
For ALC adjustment on a 20/21E20X, adjust
the potentiometer at the front of the camera.
Power Board Controls
(Optional 24VAC Board)
In dome enclosures the camera may be
connected to a power board that provides
24VAC/12VDC capability.
Videology Imaging Solutions, Inc.
®
Videology Imaging Solutions
®
, Europe B.V.
37M Lark Industrial Parkway
Greenville, Rho
de Island 02828
Tel: (401) 949
– 5332
Fax: (401) 949 – 5276
Neutronenlaan 4
5405 NH
Uden, The Netherlands
Tel: +31 (0) 413-
256261
Fax: +31 (0) 413-251712
Americas, Middle East, Far East &
Australia sales:
sales
@videologyinc.com
www.videologyinc.com
Europe & N. Eurasia sales
:
info@videology.nl
www.videology.nl
Instruction Manual
High Resolution (540TVL)
1/3” CCD Color Board Camera
20E20X / 21E20X
IMAGING SOLUTIONS INC.
Original Equipment Manufacturer
1) Power IN (Red)
2) GND (Blue)
3) Video (Yellow)
J3
32mm
32mm
IMAGE
J1
06/13/2013 INS-20E20X Rev B
Specifications Troubleshooting
Before sending the camera out for repair,
check the items below. If the problem persists
after checking these items, contact your
service center directly.
NO IMAGE:
• Is camera plugged into a proper power
supply?
• Check for proper coax cable connection.
• If a DCAI lens is used make sure it’s
plugged in.
• Check all connections are secure.
• Check that monitor is plugged in and
properly adjusted.
UNCLEAR IMAGE:
• Is lens dirty?
Dirt or fingerprints on the lens or sensor
can adversely affect the image. Gently wipe
any dirt or fingerprints off using a soft cloth
or lens cleaning paper and lens cleaning
fluid (commercially available).
• Is the monitor adjusted correctly?
• Is the lens adjusted correctly?
• Is there sufficient lighting?
Electrical
NTSC
PAL
Image Sensor
1/3” IL CCD
Picture Elements
768 x 492
752 x 585
Resolution
540 TVL
Sensitivity
0.1 Lux (30 IRE) f1.2, 3200°k
Signal To Noise Ratio
>48 dB (AGC off)
Gamma
0.45
Gain Control
AGC 36dB
Synchronization
Internal (crystal controlled)
Scan Mode
Interlaced
Backlight Comp
Default ON
White Balance
Default AWB
Contour (Edge)
Enhancement
Factory set
Iris Controls
Auto detect (Electronic or DC auto iris)
Video Output
Composite 1Vp-p CVBS @75 ohms
Power Supply
+12VDC (+/- 10%)
Power Consumption
< 2.0W
Optional Factory
Settings
Via Hardware
BLC, Mirror mode, AGC
Via Software
Day/Night, Fixed Shutter
These options require a minimum quantity order. Please
contact a Videology sale representative for more details.
Environmental
Operation Temp
0°C ~ 70°C (32° F ~ 158° F)
Storage Temp
-25°C ~ 70°C (-13° F ~ 158° F)
Operation Humidity
20% ~ 90% RH
Storage Humidity
Up to 98% RH
Lifetime MTBF
>150,000 hours
Warning: Avoid aiming the camera at the sun or other
extremely bright lights. The CCD image sensor may be
damaged if exposed to very bright objects.
Mechanical
Dimensions W x H
x D w/ pinhole
mount
32mm x 32mm x 18.14mm
(1.26” x 1.26” x 0.71”)
Weight
9.5g (0.021 lbs)
Lens Mount
Replace “X” in model number with desired
lens mount option:
Example:
Change 20E20X to
20E205 to select an
M-12 Board Mount
2 = M-12 Pinhole
5 = M-12 Board
6 = M-14 Board
8 = CS Mount
Accessories
Included
Cable (J3) 60C1026
3-pin molex unterminated
Optional
Power Board 60PB24V-02
24VAC board
  • Page 1 1
  • Page 2 2

Videology 21E20X User manual

Brand
Videology
Model
21E20X
Category
Security cameras
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents