MartinLogan MDA8 User manual

Brand: MartinLogan

Model: MDA8

Type: User manual

This manual is also suitable for

MDA16

Operating Manual

MDA16

MDA8

WARNING: To reduce the risk of re or electric shock, do not

expose this apparatus to rain or moisture, and objects lled

with liquids, such as vases, should not be placed on this ap-

paratus.

CAUTION: To prevent electric shock, match wide blade of plug

to wide slot, fully insert.

CAUTION: For continued protection against risk of re, re-

place the fuse only with the same amperage and voltage type.

Refer replacement to qualied service personnel.

WARNING: Unit may become hot. Always provide adequate

ventilation to allow for cooling. Do not place near a heat

source, or in spaces that can restrict ventilation.

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any of the ventilation openings. Install in

accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators,

heat registers, stoves or other apparatus (including am-

pliers) that produce heat.

9. Do not defeat the safety purpose of the polarized plug.

A polarized plug has two blades with one wider than the

other. The wide blade is provided for your safety. When

the provided plug does not t into your outlet, consult an

electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched,

particularly at plugs, convenience receptacles and the

point where they exit from the apparatus.

11. Only use the attachments/accessories specied by the

manufacturer.

12. Use only with a cart, stand, tripod, bracket

or table specied by the manufacturer, or

sold with the apparatus. When a cart is used,

use caution when moving the cart/apparatus

combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when

unused for long periods of time.

14. Refer all servicing to qualied service personnel. Servic-

ing is required when the apparatus has been damaged

in any way, such as power supply cord or plug is dam-

aged, liquid has been spilled or objects have fallen into

the apparatus, the apparatus has been exposed to rain

or moisture, does not operate normally, or has been

dropped.

WARNING: To reduce the risk of re or electric shock, do not

expose this apparatus to rain or moisture. Avoid installing

this unit where foreign objects may fall onto this unit and/or

this unit may be exposed to liquid dripping or splashing. On

the top of this unit, do not place:

• Burning objects (i.e. candles), as they may cause re dam-

age to this unit, and/or personal injury.

• Containers with liquid in them, as they may fall and liquid

may cause electrical shock to the user and/or damage to

this unit.

Apparatus shall not be exposed to dripping or splashing and

no objects lled with liquids, such as vases, shall be placed on

the apparatus.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

RISK OF ELECTRIC SHOCK DO NOT OPEN

The lightning ash with arrowhead

symbol within an equilateral triangle is

intended to alert the user to the presence

of uninsulated “dangerous voltage”

within the product’s enclosure that may

be of sucient magnitude to constitute a

risk of electric shock to persons.

The exclamation point within an

equilateral triangle is intended to

alert the user to the presence of

important operating and maintenance

(servicing) instructions in the literature

accompanying the appliance.

CAUTION

Do not install this equipment in a conned space such as a

case or similar. Install it away from direct sunlight, heat sourc-

es, vibration, dust, moisture, and/or cold.

Do not cover this unit with a newspaper, tablecloth, curtain,

etc. in order not to obstruct heat radiation. If the temperature

inside this unit rises, it may cause re, damage to this unit,

and/or personal injury.

Install this unit near the AC outlet and where the AC power

plug can be reached easily.

This unit is not disconnected from the AC power source when it

is turned o. This state is called the standby mode. In this state,

this unit is designed to consume a very small quantity of power.

NOTE: This product is not an auto voltage device. Connect

only to the prescribed AC outlet, i.e., 120V 50/60Hz or 240V

50/60Hz.

CAUTION: Top surface can become hot.

CAUTION: These servicing instructions are for use by qualied

service personnel only. To reduce the risk of electric shock,

do not perform any servicing other than that contained in the

operating instructions unless you are qualied to do so.

CAUTION: Changes or modications to this equipment not

expressly approved by MartinLogan for compliance could void

the user’s authority to operate this equipment.

FCC WARNING: Changes or modications not expressly ap-

proved by the party responsible for compliance could void the

user’s authority to operate the equipment.

This equipment has been tested and found to comply with the

limits for a class B digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential instal-

lation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that inter-

ference will not occur in a particular installation. If this equip-

ment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment

o and on, the user is encouraged to try to correct the inter-

ference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and MDA.

• Connect the equipment into an outlet on a circuit dierent

from that to which the MDA is connected.

• Consult the dealer or an experienced radio / TV technician

for help.

DO NOT LOCATE IN THE FOLLOWING PLACES:

To ensure long-lasting use, do not locate the unit:

• Exposed to direct sunlight.

• Near sources of heat such as heaters.

• Highly humid or poorly ventilated.

• Dusty.

• Subjected to mechanical vibrations.

• On wobbly, inclined, or otherwise unstable surfaces.

• Near windows where there is a chance of exposure to rain,

etc.

• On top of an MDA or another component which dissipates

a great deal of heat.

To ensure proper heat radiation, ensure clearance from walls

and other equipment according to the diagram.

Left: 63mm

(2.5 in) or more

Above: 15mm

(0.6 in) or more

Right: 63mm

(2.5 in) or more

IMPORTANT INFORMATION FOR UK CUSTOMERS: DO NOT cut

o the mains plug from this equipment. If the plug tted is not

suitable for the power points in your home or the cable is too

short to reach a power point, then obtain an appropriate safety

approved extension lead or consult your dealer. If, nonetheless,

the mains plug is cut o, REMOVE THE FUSE and dispose of the

PLUG immediately, to avoid possible shock hazard by inadver

tent connection to the mains supply. If this product is not pro-

vided with a mains plug, or one has to be tted, then follow the

instructions given below:

IMPORTANT: DO NOT make any connection to the larger ter

minal which is marked with the letter “E” or by the safety earth

symbol or colored GREEN or GREEN AND YELLOW.

The wires in the mains lead on this product are colored in accor

dance with the following code:

• BLUE – NEUTRAL

• BROWN – LIVE

As these colors may not correspond with the colored markings

identifying the terminals in your plug, proceed as follows:

• The BLUE wire must be connected to the terminal marked

with the letter “N” or colored BLACK.

• The BROWN wire must be connected to the terminal marked

with the letter “L” or colored RED.

When replacing the fuse, only a correctly rated and approved

type should be used, and be sure to ret the fuse cover. If in

doubt, consult a competent electrician.

NOTES ON ENVIRONMENTAL PROTECTION

At the end of its useful life, this product must not be disposed

of with regular household waste but must be returned to a

collection point for the recycling of electrical and electronic

equipment. The symbol on the product, the user’s manual,

and the packaging point this out. The materials can be reused

in accordance with their markings. Through reuse, recycling of

raw materials or other forms of recycling of old products, you

are making an important contribution to the protection of our

environment. Your local administrative oce can advise you

of the responsible waste disposal point.

CdHgPb

RECYCLING AND REUSE GUIDELINES (Europe)

In accordance with the European Union WEEE (Waste Electri-

cal and Electronic Equipment) directive eective August 13,

2005, we would like to notify you that this product may con-

tain regulated materials which, upon disposal, require special

reuse and recycling processing. For this reason, MartinLogan

has arranged with its distributors in European Union mem-

ber nations to collect and recycle this product at no cost to

you. To nd your local distributor, please contact the dealer

from whom you purchased this product or go to our website

at www.MartinLogan.com.

Please note that only the product falls under the WEEE direc-

tive. When disposing of packaging and other shipping materi-

al, we encourage you to recycle through the usual channels.

MartinLogan and any related party assume no liability for the

user’s failure to comply with any requirements.

MartinLogan is registered trademarks of MartinLogan, Ltd.

Anthem, ARC, and Paradigm are trademarks or registered

trademarks of Paradigm Electronics Inc. © Paradigm Electron-

The information contained herein may not be reproduced in

whole or in part without our express written permission. We

reserve the right to change specications or features without

notice as design improvements are incorporated.

All other trademarks are the property of their respective

owners.

TABLE OF CONTENTS

1. Introduction and Quick Start . . . . . . . . . . . . . . . . . . . . . 6

1.1 Before Making Connections ..................6

1.2 Box Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.3 In-Use Notices ..............................6

1.4 Rack and Shelf Mounting .....................6

1.5 Front Panel (Status Lights) ....................7

1.6 Back Panel .................................8

1.7 Quick Start .................................9

1.8 Setting Up a Control System .................10

2. The User Interface .............................11

2.1 Accessing the User Interface .................11

2.2 Finding the MDA’s IP Address ................11

2.3 Identifying Multiple MDAs ...................11

2.4 Zones ....................................12

2.5 Inputs Settings.............................14

2.6 General: Preferences .......................15

2.7 General: Information .......................16

2.8 General: Network Settings...................17

2.9 General: Input Status .......................18

2.10 Store/Load Settings.........................19

3. Connections and Back Panel Controls ............20

3.1 Local Area Network Connection . . . . . . . . . . . . . . 20

3.2 Speaker Connections .......................20

3.3 Connecting Stereo Speakers . . . . . . . . . . . . . . . . . 21

3.4 Connecting Mono Speakers

Using One Bridged Zone ...................22

3.5 Connecting Stereo Speakers

Using Two Bridged Zones ..................23

3.6 Subwoofer Outputs.........................24

3.7 Connecting a Passive (Non-Powered)

Subwoofer Using a Bridged Zone............25

3.8 Digital Inputs ..............................26

3.9 Digital Output (MDA16 Only) .................26

3.10 Analog Input...............................26

3.11 Analog Outputs (MDA16 Only) ...............26

3.12 Power ....................................26

3.13 Trigger Connections ........................26

3.14 RS-232 Conneciton .........................26

3.15 On Mode Switch ...........................26

3.16 Master Power Switch .......................26

3.17 DHCP or Factory Image Reset ................26

3.18 ID Indicator................................26

3.19 ARC Micro-USB Connection ..................27

3.20 Chassis Ground ............................27

3.21 Fuse......................................27

4. Anthem Room Correction .......................28

4.1 Using ARC With an MDA ......................29

5. Updating Firmware.............................30

5.1 Updating Firmware

(Using an Internet Connection)..............30

5.2 Updating Firmware

(Without an Internet Connection) ...........30

6. Fault Modes ...................................31

6.1 Front Panel Power LED......................31

6.2 Front Panel LAN LED........................31

6.3 Front Panel Zone LEDs ......................31

7. Troubleshooting ...............................32

8. Frequently Asked Questions.....................33

 9.Specications..................................34

10. Limited Warranty ..............................35

11. The Big Picture: MDA16 .........................38

12. The Big Picture: MDA8 ..........................40

1. INTRODUCTION AND QUICK START

Thank you for purchasing the MartinLogan MDA. All MartinLo-

gan products are engineered to recreate the passion of a live

musical performance and emotional involvement experienced

in the best movie theaters by utilizing the highest level of cir-

cuit design, superior parts and manufacturing techniques, in-

novative features, and intuitive ergonomics. We are condent

that their inclusion in a system signicantly enhances the en-

joyment of recordings.

1.1 BEFORE MAKING CONNECTIONS

Check that you have received all items listed below and report

discrepancies to your dealer as soon as possible. In case the

MDA needs to be transported in the future, keep the packing

materials. Retain the invoice that you received from your au-

thorized MartinLogan dealer at time of purchase. The invoice

is necessary to obtain service under warranty.

1.2 BOX CONTENTS

• MDA8 or MDA16

• Dual-jack microphone

• USB mini (Type B) cable for ARC microphone

• 3.5mm cable for ARC microphone (for future ARC Mobile

app support)

• 3.5 mm trigger cable

• IEC power cord(s) (US type for 120V model, EU/UK/AU type

for 230V model)

• 2x Rack brackets (preinstalled)

• 4x Feet (if tabletop operation required)

• 4x Phillips head screws (for attaching feet)

• MDA16: 8x Euroblock Connectors (preinstalled)

• MDA8: 4x Euroblock Connectors (preinstalled)

1.3 IN-USE NOTICES

• Disconnect the power cord or ip the AC switch to OFF be-

fore connecting or disconnecting any components.

• If the MDA was transported or stored in the cold, let it

reach room temperature before use.

• Do not remove the top cover.

• Do not modify the product.

• Due to continuing advances, operational characteristics

may change. If this manual contains discrepancies, please

check www.MartinLogan.com for the latest manual.

1.4 RACK AND SHELF MOUNTING

These MDAs ship with rack brackets installed. If shelf mount-

ing is desired, you can remove the rack brackets using a T10

Torx driver. Using a Phillips screwdriver, attach four feet to the

bottom of the MDA using the included screws.

MDA16 Front Panel

MDA8 Front Panel

1.5 FRONT PANEL (STATUS LIGHTS)

Power: When blue, the MDA is on and ready to play. When

red, the MDA has entered network standby mode.

LAN: When blue, a 100M or faster network is connected.

Red indicates a 10M connection. When o, there is no net-

work connection.

Numbers: When the top indicator turns blue, the indicat-

ed channel is active. The bottom indicator turns blue when

audio is detected. When ashing blue or red, it is in fault

mode.

For more information, please refer to sections 6 (Fault Modes)

and 7 (Troubleshooting).

1.6 BACK PANEL

Analog RCA stereo inputs (MDA16 has eight, MDA8 has

four)

Optical digital audio inputs (MDA16 has two, MDA8 has

one)

Coaxial digital audio inputs (MDA16 only)

Optical digital audio output (MDA16 only)

Zone 6 and 7 analog outputs (MDA16 only)

Ethernet connection for ARC (Anthem Room Correction),

software installation, and control

RS-232 (serial) connection for legacy control

On mode switch (trigger / auto / external command)

DHCP reset / factory reset

Master power switch

Fuse

Serial number label

Micro USB type B for ARC via PC or Mac (if LAN is not avail-

able)

Power cord inlet (IEC C18 type)

Rear ID (identify) light

5–24V DC/AC 3.5 mm trigger input/loop

MAC address label

Chassis ground terminal

Subwoofer outputs (MDA16 has eight, MDA8 has four)

Euroblock speaker terminals

For more information, please refer to section 3 (Connections

and Back Panel Controls).

MDA16 Back Panel

MDA8 Back Panel

1.7 QUICK START

This quick start section includes just enough information to

get the MDA operational and to run Anthem Room Correction.

For a deeper understanding of speaker and subwoofer con-

nection options, advanced conguration settings, and control

system integration, please review the rest of this manual.

ANALOG OUT

1. Install the MDA in a rack or install the feet using a Phillips

screwdriver for tabletop operation. (Rack brackets can be

removed using a T10 Torx driver).

2. Speaker Connection(s): Connect a pair of speakers to

Zone 1 using a Euroblock (aka Phoenix

) connector (in-

cluded) which accepts speaker wire from 28 up to 12 gauge.

a. Pull both sides of the Euroblock connector from Zone 1

to remove it from the MDA.

b. Use a small slotted screwdriver to loosen and tight-

en each contact on the Euroblock when inserting the

speaker wire.

c. Follow positive (+) and negative (–) indications shown

on the Euroblock connector.

d. After attaching speaker wires to the Euroblock connec-

tor, insert it back into the MDA.

3. Repeat to connect speakers in additional zones.

4. Input Connections(s): Connect analog sources using RCA

cables. By default, Analog 1 plays in Zone 1, Analog 2 in

Zone 2, and so on. You can change source assignments

later if so desired.

5. Power Connection: Insert a power cord into the MDA’s AC

input. Plug the cord into a wall outlet. Make sure to respect

the voltage rating shown beside the AC receptacle.

BASIC CONFIGURATION

1. Control Settings:

a. On Mode Switch: Set to Auto.

b. Master AC Power Switch: Set to On.

2. When the MDA detects audio in a zone, the corresponding

indicator light (at the bottom) turns blue, and the zone’s

power indicator light (at the top) turns blue. You should

now hear the music.

ADVANCED CONFIGURATION AND CONTROL

SYSTEM INTEGRATION

1. Control Settings:

a. On Mode Switch: Set to Ext Cmd.

b. Master AC Power Switch: Set to On.

2. Network Connection: Connect the MDA’s Network con-

nection to a LAN using an Ethernet cable. The network

router should support DHCP and will automatically assign

an IP address to the MDA.

3. Powered subwoofer connection(s) [optional]: Connect a

powered subwoofer to Zone 1 using an RCA cable. Repeat

to connect subwoofers in additional zones.

5. Input Connections(s): Connect each audio source using

the desired connection method.

a. Analog Left/Right RCA: Connect to Analog inputs.

b. Digital, Optical (aka Toslink): Connect to Digital 1 or

2 (Digital 1 only on MDA8).

c. Digital, Coaxial: Connect to Digital 3 or 4 (not available

on MDA8).

ACCESSING THE CONFIGURATION INTERFACE

For initial setup, the MDA should be connected to a network

and plugged into the wall with the On Mode switch set to EXT

CMD. Turn on the MDA by setting the master power switch to

On. The Power light on the front panel indicates that the MDA

has powered up. Once the LAN light on the front panel turns

blue or red, the MDA has connected to your network and ac-

quired a network address.

The MDA is congured using an interface accessed using a

web browser. Identify the MDA’s IP address to proceed. You

can discover the MDA’s IP address using the ARC Genesis

software (available on AnthemARC.com). Start the program,

choose Launch ARC, and hover your mouse cursor over the

MDA, wait for a second, and it shows the IP address in the de-

vice discovery screen. Note that the last few characters of the

unit’s name correspond to the end of the MAC address printed

at the back of the MDA.

To access the MDA’s conguration interface, open a web

browser (we recommend Chrome or Safari), type the IP ad-

dress into the browser’s address bar, and hit enter.

When installing more than one MDA, there are multiple IP ad-

dresses. To identify each MDA, use a web browser to connect

to the rst one and click General > Preferences > Unit ID. The

ID light on the back panel ashes as will the Power indicator

on the front of the MDA. The MAC Address displayed under

General > Information matches the unique MAC Address

printed on the back of the MDA.

CONFIGURING THE MDA

1. Access the conguration interface by entering the MDA’s IP

address in a web browser’s address bar.

2. General > Information > Device Name: Create a name

for the MDA and click Apply.

3. Inputs > Analog 1 (or other input) > Input Name: Create

a name and click Apply

4. Repeat for additional inputs.

5. Zones > Zone 1 > Zone Settings >

a. Zone Name: Create a name and click Apply.

b. Input Source: Choose the input you want to hear in

this zone.

c. SpeakerProle:Select the type of speaker connected

or keep them as Generic type if not shown in the list.

6. Zones > Zone 1 > Subwoofer > Subwoofer: When there is

a sub connected to the zone’s Sub Out, set the toggle to on.

7. Repeat for additional zones.

RUNNING ANTHEM ROOM CORRECTION (ARC

)

Once speakers and subwoofers are connected and cong-

ured, and sources and zones are named, you can run room

correction for each zone that is being used. Download the ARC

Genesis software from AnthemARC.com and follow the on-

screen instructions. See section 4 for additional details.

CONTROLLING THE MDA

Play music using one of the sources connected to the MDA. In

most installations, a custom integrated control system is used

to adjust the volume and change which source is playing in

which zone. You can also adjust volume and change inputs

using the conguration interface.

• Access the conguration interface by entering the MDA’s IP

address in a web browser’s address bar.

• Zones > Zone 1 (or another zone) > Zone Settings > Input

Source: Choose the input you want to hear in this zone.

• Zones > Zone 1 (or another zone) > Volume > Zone Vol-

ume: Adjust the volume here.

1.8 SETTING UP A CONTROL SYSTEM

MDAs are compatible with IP and RS232 command protocols. A

detailed command set and discovery protocol are available on

MartinLogan.com. A variety of MartinLogan developed automa-

tion drivers are also available for download free-of-charge from

our web site for easy integration into a smart-home powered by

Crestron, Savant, and other similar controllers.

For optimum performance and enjoyment, your MDA should

be appropriately set up. If you’re using a subwoofer or sub-

woofers, ARC (Anthem Room Correction) sets crossovers and

levels for a perfect blend with the main speakers. The rest of

the settings mostly relate to your preferences. Please fully

congure all zones with the proper output modes (single-end-

ed, stereo or mono bridge), speaker prole and subwoofer

settings (present or not, active or passive) before running ARC.

2.1 ACCESSING THE USER INTERFACE

For initial setup, the MDA should be connected to a network

and plugged into the wall with the On Mode switch set to Auto.

Turn on the MDA by setting the master power switch to On.

The Power light on the front panel indicates that the MDA has

powered up. Once the LAN light on the front panel turns blue

or red, the MDA has connected to your network and acquired

a network address.

2.2 FINDING THE MDA’S IP ADDRESS

The MDA is congured using an interface accessed using a

web browser. Identify the MDA’s IP address to proceed.

You can discover the MDA’s IP address using the ARC Gene-

sis software. Start the ARC program on a PC or Mac, choose

Launch ARC, and hover your mouse cursor over the MDA, wait

for a second, and it shows the IP address in the device discov-

ery screen.

We also recommend using Fing, a free network device detec-

tion app available on iOS, Android, and Windows. This app

identies devices on a network and shows their IP addresses.

These identify with MDA8 or MDA16 or MartinLogan.

To access the MDA’s conguration interface, open a web

browser (we recommend Chrome or Safari), type the IP ad-

dress into the browser’s address bar, and hit enter.

2.3 IDENTIFYING MULTIPLE MDAs

When installing more than one MDA, there are multiple IP ad-

dresses. To identify each MDA, use a web browser to connect

to the rst one and set General > Preferences > Unit ID to On.

The ID light on the MDA’s back panel and the Power indicator

on the front ash. The MAC Address displayed under General

> Information also matches the unique MAC Address printed

on the back of the MDA. Note that the last few characters of

the factory default unit’s name correspond to the end of the

MAC address printed at the back of the MDA.

2. THE USER INTERFACE

Zones: Adjusts the settings of individual zones, allowing

zone naming, source selection, mode setup, listening

mode, speaker prole, level adjustment, tone control, vol-

ume conguration, and subwoofer setup. The top of the

page shows the individual zones.

Inputs: Allows input naming and level balancing (trim). See

section 2.5 for additional details.

General: Displays device information and allows device

naming, network conguration, and displays input selec-

tion. See sections 2.6 – 2.9 for additional details.

Store/Load: Allows import/export of device settings from

les saved on your PC or Mac. Also allows storing and load-

ing from 2 local storage areas (user’s or installer’s settings).

See section 2.10 for additional details.

The Zone taskbar shows available zones and highlights the

currently selected zone (MDA16 shows 8 zones, and MDA8

shows 4 zones). Stereo Bridge and Subwoofer Powered

by Zone 2 (4, 6, or 8) turn the even-numbered zones grey,

indicating they are disabled. In this case, settings and con-

trols of the odd-numbered zone transfer automatically to

the even-numbered zone.

Mono Bridge: Sets a single zone into a high output mode

for a single speaker. The listening mode is automatically

set to Mono when selecting Mono Bridge mode. See sec-

tion 3.4 for additional details.

Stereo Bridge: Sets a zone pair (1 & 2, 3 & 4, 5 & 6, or 7 & 8) into

2.4 ZONES

The user interface design is subject to change.

a left and right conguration. When activated, the even-num-

bered zone turns grey, and the odd-numbered zone controls

the settings. This setting allows a high output mode for a pair

of speakers with each zone acting as a discrete channel. The

listening mode is automatically set to stereo when selecting

Stereo Bridge mode. See section 3.5 for additional details.

Zone Power: Toggles the zone between active and stand-

by. When set to Auto mode and music is playing in that

zone, the toggle automatically goes back ON when analog

or digital audio is detected.

ARC: Turns ARC on and o for the zone (only available if ARC

software has been used to upload corrections for the zone).

Zone Name: Assign a name to the zone (up to 16 charac-

ters) and click Apply to save this setting. The names of the

zones appear in ARC, allowing easy identication.

Input Source: Selects the desired input source. An input

can be assigned simultaneously to multiple zones. If you

are not using the built-in matrix switching this remains

static until altered either through the web interface or IP/

RS232 control. Selecting a source here does not prevent

you from changing source dynamically during use through

a compatible home automation system.

Listening Mode > Stereo: The default listening mode. The

audio plays in stereo.

Listening Mode > Mono: Sums the left and right channels

and sends identical signals to both speakers.

Speaker Prole: Selects a specic in-wall or in-ceiling

speaker model for each zone. Selecting a particular model

allows the DSP to optimize the EQ and limiter settings. En-

able a Speaker Prole using the toggle button located right

of the drop-downs. If you don’t know the model of your

speakers, or if your speakers are not listed, select Generic.

Zone Volume: Adjusts the level of the zone. Each zone has

independent volume control. Please note that selecting

a volume level in the Web UI does not prevent you from

changing volume levels dynamically during use with a

compatible automation system.

Power On Volume: The volume level for the zone when it

turns on.

Max Volume: Prevents the volume of the zone from ex-

ceeding the desired level. Please note that an external vol-

ume adjustment cannot override this level. If an automation

system attempts to adjust the volume level higher than the

max volume setting the MDA ignores the command.

Mute: Mutes the zone.

Bass / Treble: Allows ne-tuning of the relative bass and

treble levels of the system. Please note that if using a sub-

woofer, the subwoofer level adjusts the subwoofer level

relative to the main channels.

Left / Right: Adjusts the level of the left and right channels

to set the balance.

Subwoofer: Activates and deactivates the subwoofer and

bass management. Subwoofer output does not function

unless this toggle is enabled. By default, the subwoof-

er signal is output using the Sub Out RCA connection for

the zone. If using a subwoofer, enable this before running

ARC. See section 3.6 for additional details.

Crossover: Sets the crossover point between the sub-

woofer and the main speakers. When using ARC, this value

is automatically set. To change the crossover value after

running ARC, modify the crossover setting in ARC and then

re-upload. The crossover should only be manually adjust-

ed if you are not using ARC.

Sub Level: Adjusts the level of the subwoofer relative to the

mains. When using ARC, this value is automatically set. Unlike

the Crossover setting, manually changing this value after run

ning ARC will not negatively impact subwoofer integration.

Sub Phase: Adjusts the phase of the subwoofer relative

to the main channels. Phase is adjustable from 0-180 de-

grees. If a value higher than 180 degrees is required, ad-

just Subwoofer Phase in combination with Sub Polarity for

a full 360-degree range of adjustment. When using ARC,

this value is automatically set using the Automatic Phase

Adjustment tool.

Sub Polarity: Adjusts the polarity of the subwoofer to ei-

ther 0 or 180 degrees. When selecting 180 degrees, the

subwoofer signal is inverted when compared to the main

channels. As a general guide, set Phase and Polarity to 0 if

the subwoofer is near the front speakers and set Phase to

0 and Polarity to 180 if the subwoofer is near the back of

the room. When using ARC, this value is automatically set

using the Automatic Phase Adjustment tool.

tive zones to operate together for a stereo pair of speakers

and a dedicated passive subwoofer connected in bridge

mode (and must be connected as such on the rear pan-

el of the unit). When engaged, all adjustments are made

using the controls in the odd-numbered zone, and the

even-numbered zones controls are disabled. For example,

when engaged, Zone 1 controls both left and right speak-

ers connected to Zone 1 and the subwoofer connected to

Zone 2. Enable this feature before running ARC. See sec-

tion 3.7 for additional details.

The user interface design is subject to change.

Bulk Action: Use this when you want to change input

names without clicking apply after each change. Enter

names for all applicable inputs, select Check All from un-

der the Bulk Items drop-down, then select Apply from un-

der the Bulk Items drop-down.

Input Name: Assign a custom name for each input (up to

16 characters). You must click Apply to save this setting.

This name corresponds with the input list in the MDA’s user

interface. Please note, this does not necessarily change the

input name in associated control systems.

Trim: Adjusts the relative level of each input. Use this when

one input plays at a dierent level than the others, causing

changes in volume levels during playback while switching

between sources.

2.5 INPUTS SETTINGS

The user interface design is subject to change.

Auto-ODelay:Sets the length of time a zone waits to en-

ter standby mode after not receiving an audio signal. This

option only applies when you set the On Mode switch on

the back of the MDA to Auto.

Auto-On Delay: Sets the amount of time that the MDA

waits to power up when in standby. This delay is useful

when controlling multiple MDAs with a trigger, and you

want them to power on in a staged pattern. This option

only applies when you set the On Mode switch on the back

of the MDA to Auto or Trigger.

Front Panel Brightness: Sets the brightness of the front

panel LEDs.

Digital Out Source (MDA16 only): Allows you to select

which digital (optical or coaxial) to pass to the digital op-

tical output. This setting can be manipulated dynamically

through IP/RS232. Selecting an output in the user interface

does not prevent this setting from being changed through

IP or RS232.

Unit ID (Rear LED): Setting to On causes the ID light on the

back panel and the Power indicator on the front to blink.

This control is useful if you’re trying to identify a specic

MDA in a system with multiple MDAs.

General > Preferences: This section.

General > Information: See section 2.7.

General > Network Settings: See section 2.8.

General > Input Selection: See section 2.9.

2.6 GENERAL: PREFERENCES

The user interface design is subject to change.

Model Name: Displays the MDA model.

Device Name: Assign a name to the MDA (up to 16 char-

acters) and click Apply to save this setting. The name of the

MDA appears in ARC allowing easy identication. Note that

the last few characters of the unit’s name correspond to

the end of the MAC address printed at the back of the unit.

Firmware Version: Displays the current rmware version

of the MDA. When connecting to the MDA’s web interface,

if there is an active internet connection, the MDA checks

our server and displays a notication at the bottom of the

screen if an update is available.

MAC Address: Displays the unique MAC address of the

MDA, which can be used to set a DHCP reservation in your

router.

Serial Number: Displays the unique serial number of the

MDA.

2.7 GENERAL: INFORMATION

The user interface design is subject to change.

IP Mode: Toggles the MDA between DHCP and Static net-

work assignments. Changes take eect after clicking Ap-

ply. If errors occur when adjusting static IP settings, the

MDA can be manually set back to DHCP using the DHCP

Reset / Factory Image button located on the MDA’s back

panel (refer to troubleshooting).

IP Address: Displays the MDA’s current IP address. Adjust-

able if Static is selected. Changes take eect after clicking

Apply. Set new values for IP Address, Subnet, and Gateway

before clicking Apply.

Subnet: Displays the MDA’s current subnet mask. Adjust-

able if Static is selected. Changes take eect after clicking

Apply. Set new values for IP Address, Subnet, and Gateway

before clicking Apply.

Gateway: Displays the MDA’s current gateway address.

Adjustable if Static is selected. Changes take eect after

clicking Apply. Set new values for IP Address, Subnet, and

Gateway before clicking Apply.

Apply: Save the new network settings (if they have

changed). After clicking Apply, the MDA restarts a connec-

tion with the server and the web browser should automat-

ically attempt to reconnect to the new address.

2.8 GENERAL: NETWORK SETTINGS

The user interface design is subject to change.

Displays the name assigned to each zone.

Displays the input playing in the zone and allows you to

reassign inputs. This control can be used to conrm that

the unit is appropriately responding to commands from a

3rd party automation system, or as an easy way to control

which inputs are playing in which zones.

2.9 GENERAL: INPUT STATUS

The user interface design is subject to change.

User Settings: Allows you to store the current settings to

the User Settings and load them back. The User Settings

are stored locally on the MDA and don’t require an exter-

nal le.

Installer Settings: Allows you to store the current settings

to the Installer Settings and load them back. The Installer

Settings are stored locally on the MDA and don’t require an

external le.

Factory Settings: Resets the current settings to the facto-

ry defaults. The saved user and installer settings remain

intact. It also erases ARC corrections (and turns ARC o) in

all zones. Loading the factory settings does not revert the

MDA rmware to the factory image. To revert the MDA to

the factory version of the rmware you need to use the

DHCP Reset / Factory Image reset button located on the

MDA’s back panel (refer section 7, Troubleshooting).

Current Version: Displays the current rmware version.

Latest Version: Displays the latest available rmware

version. If there is an active internet connection, the MDA

checks our servers and display a notication at the bottom

of the screen if an update is available.

Upload New Firmware: If the MDA does not have Inter-

net access, you can download the latest rmware from our

support page at MartinLogan.com. Click on Browse and se-

lect the le from your computer and then click on Update

to start the upgrade process.

Save Settings in a File: Saves a backup of the MDA’s cur-

rent settings on your computer, allowing you to copy set-

tings across MDA’s for a faster install, or if service is neces-

sary.

Import Settings from a File: Allows you to load previously

saved settings from an external le.

2.10 STORE/LOAD SETTINGS

The user interface design is subject to change.

3. CONNECTIONS AND BACK PANEL CONTROLS

3.1 LOCAL AREA NETWORK CONNECTION

A network connection is required to access the conguration

interface, run Anthem Room Correction, and use IP control.

Connect to your router using an Ethernet (CAT5) cable.

3.2 SPEAKER CONNECTIONS

Depending on the level of the input signal, the volt-

age at the outputs can be high enough to cause

electric shock – be sure that power is o when con-

necting or disconnecting anything. As well, be sure

to use speakers rated for use with this MDA – an

overdriven speaker can pose a re hazard.

MDAs oer several options for connecting speakers and pas-

sive subwoofers:

• Stereo speakers hooked to a single zone.

• For more power, a zone can be bridged to drive a single

speaker in either mono or stereo mode. Bridge mode uses

the left and right output to drive a single speaker. Mono

bridge mode uses a single zone whereas stereo bridge

uses two consecutive zones to drive a stereo pair.

• Bridge a zone to power a passive subwoofer to comple-

ment a stereo pair.

When stereo bridge is enabled, you must always use two con-

secutive zones (zones 1/2, 3/4, 5/6, or 7/ 8).

It is possible to mix-and-match zone congurations within a

single MDA. For example:

• Zone 1 (Kitchen): left & right speakers

• Zone 2 (Bathroom): left & right speakers

• Zones 3/4 (Den): left & right speakers bridged for more

power in stereo mode

• Zone 5/6 (Living Room): left & right speakers with a pas-

sive subwoofer (connected to Zone 6)

• Zone 7 (Hallway): left & right speakers bridged for more

power in mono mode

• Zone 8 (Bedroom): left & right speakers with a powered

subwoofer (connected via Zone 8 Sub Out RCA)

MDA16 Zone 1 Zone 2 Zone 3 Zone 4 Zone 5 Zone 6 Zone 7 Zone 8

Stereo Speakers Left & Right Left & Right Left & Right Left & Right Left & Right Left & Right Left & Right Left & Right

Mono Speaker Using

Mono Bridged Zone

Mono

(Left + Right)

Mono

(Left + Right)

Mono

(Left + Right)

Mono

(Left + Right)

Mono

(Left + Right)

Mono

(Left + Right)

Mono

(Left + Right)

Mono

(Left + Right)

Stereo Speakers

Using Two Bridged

Zones

Left (on zone 1)

Right (on zone 2)

[controlled via zone 1]

Left (on zone 3)

Right (on zone 4)

[controlled via zone 3]

Left (on zone 5)

Right (on zone 6)

[controlled via zone 5]

Left (on zone 7)

Right (on zone 8)

[controlled via zone 7]

Stereo Speakers and

Passive Subwoofer

Using a Bridged Zone

Left & Right (on zone 1)

Passive Sub (on zone 2)

[controlled via zone 1]

Left & Right (on zone 3)

Passive Sub (on zone 4)

[controlled via zone 3]

Left & Right (on zone 5)

Passive Sub (on zone 6)

[controlled via zone 5]

Left & Right (on zone 7)

Passive Sub (on zone 8)

[controlled via zone 7]

MDA8 Zone 1 Zone 2 Zone 3 Zone 4

Stereo Speakers Left & Right Left & Right Left & Right Left & Right

Mono Speaker Using

Mono Bridged Zone

Mono

(Left + Right)

Mono

(Left + Right)

Mono

(Left + Right)

Mono

(Left + Right)

Stereo Speakers

Using Two Bridged

Zones

Left (on zone 1)

Right (on zone 2)

[controlled via zone 1]

Left (on zone 3)

Right (on zone 4)

[controlled via zone 3]

Stereo Speakers and

Passive Subwoofer

Using a Bridged Zone

Left & Right (on zone 1)

Passive Sub (on zone 2)

[controlled via zone 1]

Left & Right (on zone 3)

Passive Sub (on zone 4)

[controlled via zone 3]

Page is loading ...

MartinLogan MDA8 User manual

Brand: MartinLogan

Model: MDA8

Type: User manual

This manual is also suitable for

MDA16

Download PDF

report

MartinLogan MDA8 User manual

This manual is also suitable for

MartinLogan MDA8 User manual

Related papers

Other documents