Page is loading ...
8006 Bed
Assembly Instructions
Parts List
1
1217
Page 1 of 5
Drawer Face x 3 Drawer Back x 3 Drawer Bottom x 3 Drawer Side x 6
N O P Q
K L M
Support
(Right Hand) x 1
Support
(Middle) x 2
Support
(Left Hand) x 1
Headboard x 2
Front Stretcher x 1
Inside Rail x 1
Trundle Front Rail x 1
Trundle Rear Rail x 1
Trundle End Slats x 2
A
C
Rear Stretcher x 1
D
E
G
H
J
Bed Slats x 1
Trundle Slats
x 2
B
F
Note: Do not assemble
using power tools.
This can cause the bolts
to be overtightened
Use 2 People
Attach the Supports (K, L & M) to the Front Stretcher (C) using the Wood
Dowels (5) and 32mm Wood Screws (6).
The Inside Rail (E) assembles to the Supports (K, L & M) using 40mm JCBs (2).
8006 Bed
Assembly Instructions
Page 2 of 5
3
C
E
K
L
L
M
5
6
5
6
5
5
6
6
2
2
2
2
Hardware List
2
M6 x 50mm JCB
x 2
M6 x 40mm JCB
x 12
M6 x 25mm JCB
x 8
M6 x 15mm JCB
x 4
Wood Dowel
(8 x 30mm) x 8
Wood Screw
(M4 x 32mm) x 50
Wood Screw
(M4 x 25mm) x 24
Wood Screw
(M4 x 16mm) x 16
Spring
Washer x 8
Flat Washer
x 8
Allen Key x 1 Metal Bracket x 2 Wheels x 4
1 2 3 4 5
6 7 8 9 10
11 12 13
1217
8006 Bed
Assembly Instructions
Page 3 of 5
Slide the Drawer Bottom (P) into the groove on the Drawer Sides (Q).
5
Assemble the Drawer Face (N)
to the Drawer Sides (Q).
6
Important: Assemble the small
wheels at the back
Q
Q
O
7
7
P
Q
Q
N
7
Q
Q
7
Assemble the Drawer Sides (Q) to the Drawer Back (O), making sure the small wheels
on the sides are next to the Drawer Back (O).
4
1217
8006 Bed
Assembly Instructions
Page 4 of 5
Notch
A
C
E
A
1
3
9
10
A
Loosley fit the 25mm JCBs, Spring Washers
& Flat Washers to the Headboards (A).
7
Hook on the Rear Stretcher (D) onto
the Headboards (A).
D
A
A
Hook the assembled Front Stretcher (C)
onto the Headboards (A). The Inside Rail (E)
fits into the notch on the Headboard (A) and
is fixed with 50mm JCBs (1).
8
9
Use 2 People
1217
8006 Bed
Assembly Instructions
Page 5 of 5
G
H
J
J
F
F
2
6
Screw the Bed Slats (B)
between the Front & Rear
Stretchers (C & D).
Finally, fit the assembled
Drawers.
2
4
12
J
G
6
F
Fit the Wheels (13) to the Trundle
End slats (J) with the 16mm
Screws (8).
B
6
6
C
D
J
13
13
8
8
Assemble the Trundle Slats & Trundle End Slats (F & J)
to the Trundle Front Rail (G) &
Trundle Rear Rails (H).
Assembled Drawer
1217
/
