Makita XCV15ZX User manual

Brand: Makita

Model: XCV15ZX

Category: Power tools

Type: User manual

This manual is also suitable for

INSTRUCTION MANUAL

MANUAL DE INSTRUCCIONES

Cordless Vacuum Cleaner

Aspiradora Inalámbrica

XCV14

XCV15

XCV16

IMPORTANT: Read Before Using.

IMPORTANTE: Lea antes de usar.

2 ENGLISH

ENGLISH (Original instructions)

SPECIFICATIONS

Model: XCV14 XCV15 XCV16

Standard lter type Cloth lter (for dry

and wet dust)

Powder lter (for dry dust)

Maximum air volume

(with BL1850B, ø38 mm (1-1/2") x 2.5 m (98-1/2") hose)

2.1 m

/min (74 cu.ft/min)

Vacuum (with BL1850B, ø38 mm (1-1/2") x 2.5 m (98-1/2") hose) 9.8 kPa

Recoverable capacity Dust 15 L (4.0 gal.)

Water 12 L (3.2 gal.) -

Dimensions (L x W x H) 366 mm x 334 mm x 421 mm

(14-3/8″ x 13-1/8″ x 16-1/2″)

Rated voltage D.C. 36 V

Net weight 7.3 - 7.9 kg

(16.0 - 17.4 lbs)

8.0 - 8.6 kg (17.6 - 19.0 lbs)

Bluetooth

version - 4.1

(Bluetooth low energy)

Frequency band - 2,402 - 2,480 MHz

Maximum radio-frequency power - 1.0 dBm (EIRP)

Transmission range - Approximately 10 m

•

Due to our continuing program of research and development, the specications herein are subject to change without notice.

• Specications and battery cartridge may differ from country to country.

• The weight does not include accessories but battery cartridge(s). The lightest and heaviest combination weight

of the appliance and battery cartridge(s) are shown in the table.

• For wet dust, the oat and the water lter or cloth lter are required.

The Bluetooth

word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of

such marks by Makita is under license. Other trademarks and trade names are those of their respective owners.

Applicable battery cartridge and charger

Battery cartridge

BL1815N / BL1820B / BL1830 / BL1830B / BL1840B / BL1850B / BL1860B

Charger DC18RC / DC18RD / DC18RE / DC18SD / DC18SE / DC18SF

•

Some of the battery cartridges and chargers listed above may not be available depending on your region of residence.

WARNING: Only use the battery cartridges and chargers listed above. Use of any other battery cartridges

and chargers may cause injury and/or re.

SAFETY WARNINGS

IMPORTANT SAFETY

INSTRUCTIONS

When using an electrical appliance,

basic precautions should always be fol-

lowed, including the following:

READ ALL

INSTRUCTIONS

BEFORE USING

THIS APPLIANCE.

3 ENGLISH

WARNING

To reduce the risk of re, electric shock

or injury:

Do not leave appliance when battery

tted. Remove battery from appliance

when not in use and before servicing.

2. Do not allow to be used as a toy.

Close attention is necessary when

used by or near children.

3. Use only as described in this man-

ual. Use only manufacturer's recom-

mended attachments.

4. Do not use with damaged battery.

If appliance is not working as it

should, has been dropped, dam-

aged, left outdoors, or dropped into

water, return it to a service center.

5. Do not handle battery or appliance

with wet hands.

Do not put any object into openings.

Do not use with any opening blocked;

keep free of dust, lint, hair, and any-

thing that may reduce air ow.

7. Keep hair, loose clothing, ngers,

and all parts of body away from

openings and moving parts.

8. Turn off all controls before removing

the battery cartridge.

Use extra care when cleaning on stairs.

10. Do not use to pick up ammable or

combustible liquids, such as gaso-

line, or use in areas where they may

be present.

11. Use only the charger supplied by

the manufacturer to recharge.

12. Do not pick up anything that is burn-

ing or smoking, such as cigarettes,

matches, or hot ashes.

13. Do not use without lters in

place. Replace a damaged lter

immediately.

14. Do not charge the battery outdoors.

15. (For the powder lter models.) Do not

use on wet surfaces. Do not expose

to rain. Store indoors.

16. (For the cloth lter models.) Do not

expose to rain. Store indoors.

17. Always install oat before any wet

pick-up operation.

18.

Do not use the cleaner as a stool or

work bench. The machine may fall

down and may result in personal injury.

19. Do not vacuum the following:

• Flammable liquid (kerosene,

gasoline, solvents such as ben-

zine, thinner, etc.)

• Hot substances that are burn-

ing or smoking (cigarettes,

matches, incense sticks, can-

dles, hot ashes), sparks and

metal dust generated by cutting

or grinding metal, etc.

• Flammable material (toner,

paint, spray, etc.)

• Foam like carpet cleaning agent,

etc. (they may cause explosion

or re)

• Explosive or pyrophoric sub-

stances (nitroglycerin, alumi-

num, magnesium, titanium, zinc,

red phosphorus, yellow phos-

phorus, celluloid, etc. and their

dust, gas or steam)

• Sharp objects (glass, cutlery,

wood splinter, metal, stone, nail,

razor, push pin, etc.)

• Solidifying and conductive

ne powder (metal or carbon

powder)

• Dehumidier

• Large amount of powder (our,

re extinguisher powder, etc.)

• Substances that cause toxic

symptoms

• Aggressive chemicals (acid,

leach, etc.)

• Liquid or damp garbage, includ-

ing vomit and excreta

• Asbestos

• Pesticides

Such action may cause re, injury

and/or property damage.

To reduce your exposure to these

chemicals, always wear approved

respiratory protection such as dust

masks that are specially designed

to lter out microscopic particles.

Direct the exhaust air away from

your face and body.

4 ENGLISH

NOTE: Read the OSHA regulation on

silica dust to understand the require-

ments needed to reduce exposure to

silica dust at the jobsite. Specic rules

apply to the drilling, demolition cutting

and grinding materials that contain sil-

ica. All OSHA requirements regarding

reducing silica dust can be found at

the OSHA website: www.osha.gov.

Battery tool use and care

Prevent unintentional starting. Ensure

the switch is in the off-position before

connecting to battery pack, picking

up or carrying the appliance. Carrying

the appliance with your nger on the

switch or energizing appliance that have

the switch on invites accidents.

2. Disconnect the battery pack from

the appliance before making any

adjustments, changing accessories,

or storing appliance. Such preventive

safety measures reduce the risk of

starting the appliance accidentally.

3. Recharge only with the charger

specied by the manufacturer. A

charger that is suitable for one type of

battery pack may create a risk of re

when used with another battery pack.

Use appliances only with specically desig-

nated battery packs. Use of any other battery

packs may create a risk of injury and re.

5. When battery pack is not in use,

keep it away from other metal

objects, like paper clips, coins,

keys, nails, screws or other small

metal objects, that can make a

connection from one terminal to

another. Shorting the battery terminals

together may cause burns or a re.

6. Under abusive conditions, liquid

may be ejected from the battery;

avoid contact. If contact acciden-

tally occurs, ush with water. If liq-

uid contacts eyes, additionally seek

medical help. Liquid ejected from the

battery may cause irritation or burns.

Do not use a battery pack or appliance

that is damaged or modied. Damaged

or modied batteries may exhibit

unpredictable behaviour resulting in

re, explosion or risk of injury.

8. Do not expose a battery pack or

appliance to re or excessive tem-

perature. Exposure to re or tem-

perature above 130 °C may cause

explosion.

9. Follow all charging instructions

and do not charge the battery

pack or appliance outside of the

temperature range specied in the

instructions. Charging improperly or

at temperatures outside of the speci-

ed range may damage the battery and

increase the risk of re.

10. Have servicing performed by a

qualied repair person using only

identical replacement parts. This will

ensure that the safety of the product is

maintained.

11. Do not modify or attempt to repair

the appliance or the battery pack

except as indicated in the instruc-

tions for use and care.

SAVE THESE

INSTRUCTIONS.

This appliance is intended for commer-

cial use.

Symbols

The followings show the symbols used for

tool.

volts

direct current

Take particular care and

attention.

Never stand on the cleaner.

alternating current

amperes

hertz

Class II Construction

5 ENGLISH

Important safety

instructions for

battery cartridge

Before using battery cartridge, read

all instructions and cautionary mark-

ings on (1) battery charger, (2) bat-

tery, and (3) product using battery.

2. Do not disassemble battery

cartridge.

3. If operating time has become

excessively shorter, stop operating

immediately. It may result in a risk

of overheating, possible burns and

even an explosion.

4. If electrolyte gets into your eyes,

rinse them out with clear water and

seek medical attention right away. It

may result in loss of your eyesight.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with

any conductive material.

(2) Avoid storing battery cartridge

in a container with other metal

objects such as nails, coins, etc.

(3) Do not expose battery cartridge

to water or rain.

A battery short can cause a large

current ow, overheating, possible

burns and even a breakdown.

6. Do not store the tool and battery

cartridge in locations where the

temperature may reach or exceed 50

°C (122 °F).

7. Do not incinerate the battery car-

tridge even if it is severely damaged

or is completely worn out. The bat-

tery cartridge can explode in a re.

8. Be careful not to drop or strike

battery.

9. Do not use a damaged battery.

10. The contained lithium-ion batteries

are subject to the Dangerous Goods

Legislation requirements.

For commercial transports e.g. by

third parties, forwarding agents,

special requirement on packaging

and labeling must be observed.

For preparation of the item being

shipped, consulting an expert for

hazardous material is required.

Please also observe possibly more

detailed national regulations.

Tape or mask off open contacts and pack

up the battery in such a manner that it

cannot move around in the packaging.

11. Follow your local regulations relat-

ing to disposal of battery.

12. Use the batteries only with the prod-

ucts specied by Makita. Installing

the batteries to non-compliant products

may result in a re, excessive heat,

explosion, or leak of electrolyte.

SAVE THESE

INSTRUCTIONS.

CAUTION: Only use genuine Makita batteries.

Use of non-genuine Makita batteries, or batteries that

have been altered, may result in the battery bursting

causing res, personal injury and damage. It will

also void the Makita warranty for the Makita tool and

charger.

Tips for maintaining maximum

battery life

1. Charge the battery cartridge before completely

discharged. Always stop tool operation and

charge the battery cartridge when you notice

less tool power.

Never recharge a fully charged battery cartridge.

Overcharging shortens the battery service life.

3. Charge the battery cartridge with room tem-

perature at 10 °C - 40 °C (50 °F - 104 °F). Let

a hot battery cartridge cool down before

charging it.

4. Charge the battery cartridge if you do not use

it for a long period (more than six months).

Important safety instructions for

wireless unit

1. Do not disassemble or tamper with the cleaner.

The wireless unit in the cleaner cannot be

removed.

2. Do not operate the wireless activation function

in places where medical instruments, heart

pace makers, or automated devices, such as

automatic doors and re alarms, are nearby.

3. Do not use the cleaner in places where the

temperature exceeds 50°C (122°F).

4. The wireless unit is an accurate instrument. Be

careful not to drop or strike the cleaner.

5. Do not leave the cleaner in a place where

static electricity or electrical noise could be

generated.

6 ENGLISH

PARTS DESCRIPTION

Model XCV14

(Cloth lter (for dry and wet dust) model)

► 1. Tank cover 2. Float 3. Float cage 4. Cloth lter

5. Tank

Model XCV15, XCV16

(Powder lter (for dry dust) model)

► 1. Tank cover 2. Powder lter (HEPA) 3. Damper

4. Prelter 5. Tank

FUNCTIONAL

DESCRIPTION

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before adjusting or checking function on the tool.

Installing or removing battery

cartridge

CAUTION: Always switch off the tool before

installing or removing of the battery cartridge.

CAUTION: Hold the cleaner and the battery

cartridge rmly when installing or removing bat-

tery cartridge. Failure to hold the cleaner and the

battery cartridge rmly may cause them to slip off

your hands and result in damage to the cleaner and

battery cartridge and a personal injury.

CAUTION: Be careful not to pinch your n-

gers when opening or closing the battery cover.

Failure to do so may cause personal injury.

To install the battery cartridge, release the lock rst, and

then open the battery cover. After that, insert the battery

cartridge.

► 1. Lock 2. Battery cover

Align the tongue on the battery cartridge with the groove

in the housing and slip it into place. Insert it all the way

until it locks in place with a little click. Then lock the

battery cover.

► 1. Battery cartridge

7 ENGLISH

To remove the battery cartridge, slide it from the tool

while sliding the button in front of the cartridge.

CAUTION: Always install the battery cartridge

fully until the red indicator cannot be seen. If not,

it may accidentally fall out of the cleaner, causing

injury to you or someone around you.

CAUTION: Do not install the battery cartridge

forcibly. If the cartridge does not slide in easily, it is

not being inserted correctly.

NOTE: The cleaner does not work with only one

battery cartridge.

Indicating the remaining battery

capacity

Only for battery cartridges with the indicator

► 1. Indicator lamps 2. Check button

Press the check button on the battery cartridge to indi-

cate the remaining battery capacity. The indicator lamps

light up for a few seconds.

Indicator lamps Remaining

capacity

Lighted Off Blinking

75% to 100%

50% to 75%

25% to 50%

0% to 25%

Charge the

battery.

The battery

may have

malfunctioned.

NOTE: Depending on the conditions of use and the

ambient temperature, the indication may differ slightly

from the actual capacity.

Indicating the remaining battery

capacity

► 1. Battery indicator 2. Check button

Press the check button to indicate the remaining battery

capacities. The battery indicators correspond to each

battery.

Battery indicator status Remaining

battery

capacity

Off

Blinking

50% to 100%

20% to 50%

0% to 20%

Charge the

battery

NOTE: During the cleaner turned on with the stand-by

switch set to "AUTO", the battery indicator does not

work.

8 ENGLISH

Tool / battery protection system

The tool is equipped with a tool/battery protection sys-

tem. This system automatically cuts off power to the

motor to extend tool and battery life. The tool will auto-

matically stop during operation if the tool or battery is

placed under one of the following conditions:

Overload protection

When the tool is operated in a manner that causes it to

draw an abnormally high current, the tool automatically

stops without any indication. In this situation, turn the

tool off and stop the application that caused the tool to

become overloaded. Then turn the tool on to restart.

Overheat protection

On Blinking

When the tool is overheated, the tool stops automati-

cally, and the battery indicator blinks about 60 seconds.

In this situation, let the tool cool down before turning the

tool on again.

Overdischarge protection

When the battery capacity becomes low, the tool stops

automatically. If the product does not operate even

when the switches are operated, remove the batteries

from the tool and charge the batteries.

Switch action

► 1. Stand-by switch 2. Power button 3. Suction force

adjusting knob

To start the cleaner:

1. Set the stand-by switch to the "I" side. The cleaner

gets into stand-by state.

2. Press the power button.

To make the cleaner get into stand-by mode, press the

power button again.

To turn off the cleaner, set the stand-by switch to the

"O" side.

The suction power can be adjusted according to your

work need.

Suction power can be increased by turning the suc-

tion force adjusting knob from the

symbol to

the symbol.

NOTICE: Always set the stand-by switch to the "O"

side when not using the cleaner for long time. The

cleaner consumes power during stand-by state.

Auto-suction stop during wet

suction operation

Only for the cloth lter model

WARNING: Do not use for a long time while

the oat is at work. Using the cleaner with its oat at

work for a long time can cause overheat, resulting in

the cleaner deformation.

WARNING: Do not pick up foam or soapy

liquid. Picking up foam or soapy liquid can cause

foam to come out of air exit before the oat works.

Continuing to using in this condition may cause an

electric shock and breakage of the cleaner.

Auto-suction stop works only when using with the oat

and oat cage.

The cleaner has a oat mechanism that prevents water

from immersing into the motor when picking up more

than a certain amount of water. When the tank is full

and the cleaner no longer picks up water, switch off the

cleaner and empty the tank.

Locking or unlocking the caster

► 1. Caster 2. Stopper lever 3. FREE position

4. LOCK position

Locking the caster is convenient when storing the

cleaner, stopping the work on the way and keeping the

cleaner still.

To operate the stopper, move it by hand.

To lock the caster with a stopper, lower the stopper

lever and the caster no longer will rotate. To release the

caster from the locked position, raise the stopper lever.

NOTE: When moving the cleaner, make sure that

the caster is unlocked. Moving the cleaner with the

caster in the locked position may cause damage to

the caster.

9 ENGLISH

Carriage handle

When carrying the cleaner, carry it by holding the han-

dle on the head. The handle is retractable at the head

when not in use.

ASSEMBLY

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before carrying out any work on the tool.

CAUTION: Always wear dust mask during

assembly or maintenance.

Installing the powder lter (HEPA)

and prelter (for dry dust)

Optional accessory for cloth lter model

CAUTION: Never pick up water or other liq-

uids or wet dusts when using the powder lter.

Picking up such things may cause the powder lter

breakage.

To use powder lter:

1. Remove the oat cage and oat by removing the

bolts.

► 1. Float 2. Float cage

2. Place the prelter in the tank with aligning the

mounting position markings.

3. Mount the damper on the powder lter and then

place them in the prelter with aligning the mounting

position markings.

4. Finally, mount the tank cover and lock it.

► 1. Tank cover 2. Powder lter (HEPA) 3. Damper

4. Prelter 5. Tank 6. Mounting position marking

NOTICE: Before using the powder lter, make

sure that prelter and damper are always used

together. It is not allowed to install powder lter

solely.

Installing the water lter

Optional accessory for cloth lter model

CAUTION: Never pick up water or wet dust

without the oat and the cloth lter or the water

lter.

CAUTION: For picking up wet dust, make

sure that the oat cage and the oat are installed

on the cleaner.

CAUTION: When installing the water lter on

the tank, set it tight at the opening of the tank so

that the hook of the water lter engages the tank

opening rmly and there is no space between the

water lter and the tank.

10 ENGLISH

To pick up water or wet dust only, the water lter is more

suitable than the cloth lter.

When installing the water lter, align its mounting posi-

tion mark with the one on the tank.

► 1. Water lter 2. Tank 3. Mounting position marking

NOTE: It is recommended using water lter when

picking up large amount of water repeatedly.

Otherwise vacuum ability may be reduced in case of

cloth lter.

Installing the paper pack

Optional accessory

WARNING: When using the paper pack, also

use the cloth lter or prelter together that is

preinstalled on the cleaner. Failure to use the cloth

lter / prelter together may cause unusual noise and

heat, resulting in a re.

CAUTION: (For the cloth lter model)

•

Never pick up water or other liquids or wet

dusts when using the paper pack. Picking up

such things may cause the paper pack breakage.

• Before using the paper pack, make sure that

powder lter (optional accessory), damper

(optional accessory) and prelter are always

used together.

CAUTION: (For the powder lter model)

• Before using the paper pack, make sure

that powder lter, damper and prelter are

always used together.

1. Remove the rubber holder.

► 1. Rubber holder

2. Extend the paper pack.

3. Align the paper pack opening with the dust suction

opening of the cleaner.

4. Insert the cardboard of the paper pack onto the

holder so that it is positioned at the end beyond the

detent protrusion.

► 1. Paper pack 2. Holder

Installing the polyethylene bag

Cleaner can also be used without polyethylene bag.

However, using polyethylene bag is easier to empty the

tank without letting your hands dirty.

Spread the polyethylene bag in the tank. Insert it

between the holder plate and the tank, and pull it to the

hose inlet.

► 1. Holder plate 2. Polyethylene bag

11 ENGLISH

Spread the bag around the top of the tank so that the

cloth lter / prelter edge can catch and hold the bag

securely.

► 1. Cloth lter / prelter

NOTE: A polyethylene bag available on the

market can be used. 0.04 mm or thicker one is

recommended.

NOTE: Too much dust will tear the bag easily, so

do not collect the dust more than the half of the bag

capacity.

Emptying the polyethylene bag

WARNING: Always make sure that the

cleaner is switched off and the battery cartridge is

removed before emptying the polyethylene bag.

Failure to do so may cause an electric shock and

serious personal injury.

CAUTION: Do not apply a great impact on the

oat cage and tank. Applying a great impact may

cause deformation and damage to the parts.

CAUTION: Empty the tank at least once a day

although this depends on picked-up dust volume

in the tank. Or, the suction force will weaken and the

motor may be broken.

CAUTION: Do not grab the hook when empty-

ing the tank. Grabbing the hook may cause the hook

to break.

Unhook and lift up the tank cover.

Shake off the dust from the cloth lter / prelter and then

take the polyethylene bag out of the tank.

NOTE: Take the polyethylene bag carefully out of the

tank so that the polyethylene bag cannot be caught

and torn by the protrusion inside the tank when emp-

tying it.

NOTE: Empty the polyethylene bag before it

becomes full. Too much dust in the tank may cause

the polyethylene bag to be torn.

Installing the tool box

1. Release the lock of the battery cover, and open

the battery cover.

2. Set the rails on the tool box along the grooves on

the housing.

3. Close the battery cover and apply the lock.

The tool box is convenient for carrying batteries, pipe,

or cuffs.

Connecting the hose

NOTICE: Never force the hose for bending or

stamp it. Never move the cleaner by a hose.

Forcing, stamping and pulling the hose may cause a

breakage or deformation of the hose.

NOTICE: When picking up large wastes such as

planer carvings, concrete dusts or similar other

than small wastes, use the 38 mm inner diameter

hose (optional accessory). Using the 28 mm inner

diameter hose (optional accessory) may cause a

hose stufng and damage.

12 ENGLISH

Insert the hose onto the mounting port of the tank and

turn it clockwise until it locks.

WIRELESS ACTIVATION

FUNCTION

For XCV16 only

What you can do with the wireless

activation function

The wireless activation function enables clean and

comfortable operation. By connecting a supported tool

to the cleaner, you can run the cleaner automatically

along with the switch operation of the tool.

NOTICE: Be sure to refer to the instruction man-

ual of the tool when using the cleaner with wire-

less activation function.

NOTICE: Do not disassemble or tamper with the

wireless unit.

NOTICE: Always close the lid of the wireless unit

in the tool when operating or storage.

NOTICE: Do not remove the wireless unit from

the tool while the power is being supplied to the

tool. Doing so may cause a malfunction of the wire-

less unit.

NOTICE: Do not press the wireless activation

button too hard and/or press the button with an

object with a sharp edge.

NOTE: Wireless activation needs Makita tools

equipped with the wireless unit.

NOTE: Prior to the initial use of the wireless activa-

tion function with each tool, the tool registration is

required. Once the registration is nished with the

tool, the re-registration is not required unless it is

cancelled.

NOTE: Before registration, be sure that the wireless

unit is properly inserted into the tool.

NOTE: One cleaner can register up to 10 tools. If

more than 10 tools are registered to the cleaner, the

tool registered earliest will be cancelled automatically.

NOTE: The position of the wireless activation button

varies depending on the tool.

NOTE: The cleaner also starts by pressing the power

button when the stand-by switch is set to "AUTO".

However the power button will not actuate when the

wireless activation function is used.

Tool registration for the cleaner

NOTE: A Makita tool supporting the wireless activa-

tion function is required for the tool registration.

NOTE: Finish installing the wireless unit to the tool

before starting the tool registration.

NOTE: During the tool registration, do not pull the

switch trigger on the tool or turn on the power switch

on the cleaner.

NOTE: Refer to the instruction manual of the tool, too.

If you wish to activate the cleaner along with the

switch operation of the tool, nish the tool registration

beforehand.

1. Install the batteries to the cleaner and the tool.

2. Set the stand-by switch on the cleaner to "AUTO".

► 1. Stand-by switch

13 ENGLISH

3. Press the wireless activation button on the cleaner

for 3 seconds until the wireless activation lamp blinks in

green. And then press the wireless activation button on

the tool in the same way.

► 1. Wireless activation button 2. Wireless activation

lamp

If the cleaner and the tool are linked successfully, the

wireless activation lamps will light up in green for 2

seconds and start blinking in blue.

NOTE: The wireless activation lamps nish blinking

in green after 20 seconds elapsed. Press the wireless

activation button on the tool while the wireless acti-

vation lamp on the cleaner is blinking. If the wireless

activation lamp does not blink in green, push the wire-

less activation button briey and hold it down again.

NOTE: When performing two or more tool registration

for the cleaner, nish the tool registration one by one.

Starting the wireless activation

function

NOTE: Finish the tool registration for the cleaner for

wireless activation.

NOTE: Always place the cleaner so that you can see

the status of the wireless activation lamp.

NOTE: Refer to the instruction manual of the tool, too.

After registering a tool to the cleaner, the cleaner will

automatically runs along with the switch operation of

the tool.

1. Install the wireless unit to the tool.

2. Connect the hose of the cleaner with the tool.

3. Set the stand-by switch on the cleaner to "AUTO".

► 1. Stand-by switch

4. Push the wireless activation button on the tool

briey. The wireless activation lamp will blink in blue.

► 1. Wireless activation button 2. Wireless activation

lamp

5. Pull the switch trigger of the tool. Check if the

cleaner runs while the switch trigger on the tool is being

pulled.

To stop the wireless activation, push the wireless activa-

tion button on the tool, or set the stand-by switch on the

cleaner to "I" or "O".

14 ENGLISH

NOTE: The wireless activation lamp on the tool will

stop blinking in blue when there is no operation for

2 hours. In this case, set the stand-by switch on the

cleaner to "AUTO" and press the wireless activation

button on the tool again.

NOTE: The cleaner starts/stops with a delay. There is

a time lag when the cleaner detects a switch opera-

tion of the tool.

NOTE: The transmission distance of the wireless unit

may vary depending on the location and surrounding

circumstances.

NOTE: When two or more tools are registered to one

cleaner, the cleaner may start running even if you

don't pull the switch trigger because other user is

using the wireless activation function.

Cancelling tool registration for the

cleaner

Perform the following procedure when cancelling the

tool registration for the cleaner.

1. Install the batteries to the cleaner and the tool.

2. Set the stand-by switch on the cleaner to "AUTO".

► 1. Stand-by switch

3. Press the wireless activation button on the cleaner

for 6 seconds. The wireless activation lamp blinks in

green and then become red. After that, press the wire-

less activation button on the tool in the same way.

►

1. Wireless activation button 2. Wireless activation lamp

If the cancellation is performed successfully, the wire-

less activation lamps will light up in red for 2 seconds

and start blinking in blue.

NOTE: The wireless activation lamps nish blinking in

red after 20 seconds elapsed. Press the wireless acti-

vation button on the tool while the wireless activation

lamp on the cleaner is blinking. If the wireless acti-

vation lamp does not blink in red, push the wireless

activation button briey and hold it down again.

Erasing all tool registrations

You can erase all tool registrations from the cleaner as follows.

► 1. Stand-by switch 2. Wireless activation button

3. Wireless activation lamp

15 ENGLISH

1. Install the batteries to the cleaner.

2. Set the stand-by switch to "AUTO".

3. Hold down the wireless activation button for about

6 seconds until the wireless activation lamp blinks in red

(about twice per one second).

4. When the wireless activation lamp starts blinking

in red, release your nger from the wireless activation

button. Thereafter, hold down the wireless activation

button again for about 6 seconds.

5. When the wireless activation lamp starts blinking

fast (about 5 times per one second) in red, release your

nger from the wireless activation button. When the

wireless activation lamp lights up in red and later lights

off, all tool registrations are erased.

NOTE: If the wireless activation lamp does not blink

in red, press the wireless activation button briey and

try again.

Description of the wireless activation lamp status

► 1. Wireless activation button 2. Wireless activation

lamp

The wireless activation lamp shows the status of the wireless activation function. Refer to the below table for the

meaning of the lamp status.

Status Wireless activation lamp Description

Color

Blinking

Duration

Standby Blue

Cleaner: con-

tinuing

Tool: 2 hours

Waiting for the tool registration or the wireless activation function

is available.

The lamp on the cleaner blinks when the stand-by switch is set in

AUTO. The lamp on the tool blinks when the wireless activation

button is pushed. The lamp on the tool will automatically turn off

when no operation is performed for 2 hours.

When the tool is

running.

The wireless activation of the cleaner is available and the tool is

running.

Tool

registration

Green

20 seconds Ready for the tool registration. Searching the tool to be registered.

2 seconds The tool registration has been nished. The wireless activation

lamp will start blinking in blue.

Cancelling/

erasing

tool

registration

Red

(slow: 2 times/sec.)

20 seconds Ready for the cancellation of the tool registration. Searching the

tool to be cancelled.

(fast: 5 times/sec.)

When the

wireless acti-

vation button is

pressed down.

Ready to erase all tool registrations.

2 seconds The tool registration has been cancelled/erased. The wireless

activation lamp will start blinking in blue.

Others Red

3 seconds The power is supplied to the wireless unit and the wireless activa-

tion function is starting up.

Off - - The stand-by switch is not set to "AUTO".

16 ENGLISH

Troubleshooting for wireless activation function

Before asking for repairs, conduct your own inspection rst. If you nd a problem that is not explained in the manual,

do not attempt to dismantle the tool. Instead, ask Makita Authorized Service Centers, always using Makita replace-

ment parts for repairs.

State of abnormality Probable cause (malfunction) Remedy

The wireless activation lamp does

not light/blink.

The wireless unit is not installed into

the tool.

The wireless unit is improperly installed

into the tool.

Install the wireless unit correctly in the tool.

The terminal of the wireless unit and/or

the slot is dirty.

Gently wipe off dust and dirt on the terminal of the

wireless unit and clean the slot of the tool.

The wireless activation button on the

tool has not been pushed.

Push the wireless activation button on the tool

briey.

The stand-by switch on the cleaner is

not set to "AUTO".

Set the stand-by switch on the cleaner to "AUTO".

No power supply Supply the power to the tool and the cleaner.

Cannot nish tool registration / can-

celling tool registration successfully.

The wireless unit is not installed into

the tool.

The wireless unit is improperly installed

into the tool.

Install the wireless unit correctly in the tool.

The terminal of the wireless unit and/or

the slot is dirty.

Gently wipe off dust and dirt on the terminal of the

wireless unit and clean the slot of the tool.

The stand-by switch on the cleaner is

not set to "AUTO".

Set the stand-by switch on the cleaner to "AUTO".

No power supply Supply the power to the tool and the cleaner.

Incorrect operation Push the wireless activation button briey and

perform the tool registration/cancellation procedures

again.

The tool and cleaner is away from each

other (out of the transmission range).

Get the tool and the cleaner closer to each other.

The maximum transmission distance is approxi-

mately 10 m however it may vary according to the

circumstances.

Before nishing the tool registration/

cancellation;

- the switch trigger on the tool is pulled

or;

- the power button on the cleaner is

turned on.

Push the wireless activation button briey and

perform the tool registration/cancellation procedures

again.

The tool registration procedures for the

tool or the cleaner has not nished.

Perform the tool registration procedures for the tool

and the cleaner at the same timing.

Radio disturbance by other appliances

which generate high-intensity radio

waves.

Keep the tool and the cleaner away from the appli-

ances such as Wi-Fi devices and microwave ovens.

17 ENGLISH

State of abnormality Probable cause (malfunction) Remedy

The cleaner does not run along with

the switch operation of the tool.

The wireless unit is not installed into

the tool.

The wireless unit is improperly installed

into the tool.

Install the wireless unit correctly in the tool.

The terminal of the wireless unit and/or

the slot is dirty.

Gently wipe off dust and dirt on the terminal of the

wireless unit and clean the slot of the tool.

The wireless activation button on the

tool has not been pushed.

Push the wireless activation button briey and make

sure that the wireless activation lamp is blinking

in blue.

The stand-by switch on the cleaner is

not set to "AUTO".

Set the stand-by switch on the cleaner to "AUTO".

More than 10 tools are registered to

the cleaner.

Perform the tool registration again.

If more than 10 tools are registered to the cleaner,

the tool registered earliest will be cancelled

automatically.

The cleaner erased all tool

registrations.

Perform the tool registration again.

No power supply Supply the power to the tool and the cleaner.

The tool and cleaner is away from each

other (out of the transmission range).

Get the tool and the cleaner closer to each other.

The maximum transmission distance is approxi-

mately 10 m however it may vary according to the

circumstances.

Radio disturbance by other appliances

which generate high-intensity radio

waves.

Keep the tool and the cleaner away from the appli-

ances such as Wi-Fi devices and microwave ovens.

The cleaner runs while the tool's

switch trigger is not pulled.

Other users are using the wireless acti-

vation of the cleaner with their tools.

Turn off the wireless activation button of the other

tools or cancel the tool registration of the other

tools.

Cannot erase all tool registrations in

the cleaner.

Pressing the wireless button on the tool. Press the wireless button on the cleaner for erasing

all tool registrations.

The stand-by switch on the cleaner is

not set to "AUTO".

Set the stand-by switch on the cleaner to "AUTO".

The wireless activation button is not

held down correctly.

Hold down the wireless activation button for more

than 6 seconds and then release it when the wire-

less activation lamp blinks in red. Hold down the

wireless activation button for more than 6 seconds

again until the wireless activation button rapidly

blinks in red and then release the button.

MAINTENANCE

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before attempting to perform inspection or

maintenance.

NOTICE: Never use gasoline, benzine, thinner,

alcohol or the like. Discoloration, deformation or

cracks may result.

To maintain product SAFETY and RELIABILITY,

repairs, any other maintenance or adjustment should

be performed by Makita Authorized or Factory Service

Centers, always using Makita replacement parts.

Storage of accessories

The pipes can be placed into the pipe holder when not

using the cleaner for a short time.

18 ENGLISH

The hose can be stored around the tool by connecting

each ends.

Cleaning of cloth lter

Only for the cloth lter model

Clogged cloth lter causes poor suction performance.

Clean out the cloth lter from time to time.

To remove dust or particles adhering to the cloth lter,

shake the frame bottom quickly several times.

► 1. Cloth lter

Cleaning of powder lter (HEPA) and

prelter

Only for the powder lter model

Clogged powder lter, prelter and damper cause poor

suction performance. Clean out the lters and dampers

from time to time.

To remove dust or particles adhering to the lters, shake

the frame bottom quickly several times.

Occasionally wash the powder lter in water, rinse and

dry thoroughly in the shade before use. Never wash

lters in a washing machine.

NOTE: Do not rub or scratch the powder lter, the

prelter or the damper with hard objects such as a

brush and a paddle.

NOTE: The lters wear out in course of time. It is

recommended to have some spares for them.

OPTIONAL ACCESSORIES

CAUTION: These accessories or attachments

are recommended for use with your Makita tool

specied in this manual. The use of any other

accessories or attachments might present a risk of

injury to persons. Only use accessory or attachment

for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• Hose

• Front cuff (22, 24, 38)

• Straight pipe

• Corner nozzle

• Round brush

• Powder lter, HEPA (for dry dust)

• Damper

• Prelter

• Nozzle assembly

• Bent pipe

• Polyethylene bag

• Paper pack

• Holder set

• Water Filter (option for the cloth lter model)

• Makita genuine battery and charger

19 ENGLISH

NOTE: Some items in the list may be included in the

tool package as standard accessories. They may

differ from country to country.

MAKITA LIMITED WARRANTY

Please refer to the annexed warranty sheet for the

most current warranty terms applicable to this product.

If annexed warranty sheet is not available, refer to the

warranty details set forth at below website for your

respective country.

United States of America: www.makitatools.com

Canada: www.makita.ca

Other countries: www.makita.com

20 ESPAÑOL

ESPAÑOL (Instrucciones originales)

ESPECIFICACIONES

Modelo: XCV14 XCV15 XCV16

Tipo de ltro estándar Filtro de tela

(para polvo seco y

húmedo)

Filtro de polvo (para polvo seco)

Volumen de aire máximo

(con BL1850B, manguera de ø38 mm (1-1/2″) x 2,5 m (98-1/2″))

2,1 m

/min (74 cu.ft/min)

Aspiradora (con BL1850B, manguera de ø38 mm

(1-1/2″) x 2,5 m (98-1/2″))

9,8 kPa

Capacidad recuperable Polvo 15 L (4,0 gal)

Agua 12 L (3,2 gal) -

Dimensiones (La x An x Al) 366 mm x 334 mm x 421 mm

(14-3/8″ x 13-1/8″ x 16-1/2″)

Tensión nominal 36 V c.c.

Peso neto 7,3 kg - 7,9 kg

(16,0 lbs - 17,4 lbs)

8,0 kg - 8,6 kg (17,6 lbs - 19,0 lbs)

Versión de Bluetooth

- 4,1

(Bluetooth Low Energy)

Banda de frecuencia -

2 402 MHz - 2 480 MHz

Potencia máxima de radiofrecuencia - 1,0 dBm (PIRE)

Rango de transmisión -

Aproximadamente 10 m

• Debido a nuestro continuo programa de investigación y desarrollo, las especicaciones aquí incluidas están

sujetas a cambio sin previo aviso.

• Las especicaciones y el cartucho de batería pueden variar de país a país.

• El peso incluye el o los cartuchos de batería, pero no los accesorios. La combinación de menor y mayor peso

del aparato y del o los cartuchos de batería se muestra en la tabla.

• Para polvo húmedo, se requieren el otador y el ltro de agua o de tela.

El término Bluetooth

así como su marca y logo son marcas registradas propiedad de Bluetooth SIG, Inc. y su uso

por parte de Makita está autorizado bajo licencia. Las demás marcas registradas y nombres comerciales pertenecen

a sus respectivos propietarios.

Cartucho de batería y cargador aplicables

Cartucho de batería

BL1815N / BL1820B / BL1830 / BL1830B / BL1840B / BL1850B / BL1860B

Cargador DC18RC / DC18RD / DC18RE / DC18SD / DC18SE / DC18SF

• Algunos de los cartuchos de batería y cargadores enumerados arriba podrían no estar disponibles depen-

diendo de su área de residencia.

ADVERTENCIA: Use únicamente los cartuchos de batería y los cargadores indicados arriba. El uso de

cualquier otro cartucho de batería y cargador podría ocasionar una lesión y/o un incendio.

Page is loading ...

Makita XCV15ZX User manual

Brand: Makita

Model: XCV15ZX

Category: Power tools

Type: User manual

This manual is also suitable for

Download PDF

report

in other languages

español: Makita XCV15ZX Manual de usuario

Makita XCV15ZX User manual

This manual is also suitable for

Makita XCV15ZX User manual

in other languages

Related papers

Other documents