DMP Electronics XR2500F User manual

InstallatIon GuIde

XR2500F addRessaBle

FIRe alaRM ContRol Panel

MODEL XR2500F

COMMAND PROCESSOR

INSTALLATION GUIDE

FCC NOTICE

This equipment generates and uses radio frequency energy and, if not installed and used properly in strict accordance

with the manufacturer’s instructions, may cause interference with radio and television reception. It has been type tested

and found to comply with the limits for a Class A computing device in accordance with the specication in Subpart J

of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential

installation. If this equipment does cause interference to radio or television reception, which can be determined by

turning the equipment off and on, the installer is encouraged to try to correct the interference by one or more of the

following measures:

Reorient the receiving antenna

Relocate the computer with respect to the receiver

Move the computer away from the receiver

Plug the compute into a different outlet so that computer and receiver are on different branch circuits

If necessary, the installer should consult the dealer or an experienced radio/television technician for additional suggestions.

The installer may nd the following booklet, prepared by the Federal Communications Commission, helpful:

“How to identify and Resolve Radio-TV Interference Problems.”

This booklet is available from the U.S. Government Printing Ofce, Washington D.C. 20402

Stock No. 004-000-00345-4

Information furnished by DMP is believed to be accurate and reliable.

This information is subject to change without notice.

XR2500F Installation Guide Digital Monitoring Products

taBle oF Contents

Introduction

1.1 Overview ...................................................................................................... 1

1.2 System Components ...................................................................................... 1

1.3 Power Specications ...................................................................................... 1

1.4 Communication ............................................................................................. 1

1.5 Panel Zones .................................................................................................. 1

1.6 Keypad Bus ................................................................................................... 1

1.7 LX-Bus™ ....................................................................................................... 2

1.8 Outputs ........................................................................................................ 2

1.9 Relays .......................................................................................................... 2

1.10 Zone Reference ............................................................................................. 2

1.11 Compliance Instructions ................................................................................. 2

Mounting

2.1 Mounting the Enclosure .................................................................................. 3

2.2 Surface Mounting .......................................................................................... 3

2.3 Flush Mounting .............................................................................................. 3

2.4 Fire Command Center LCD Keyboard ............................................................... 3

2.5 Metal Backplate ............................................................................................. 3

2.6 Wiring Diagram ............................................................................................. 4

AC Connection

3.1 Transformers and AC Power Connection .......................................................... 5

3.2 16 VAC Transformer ...................................................................................... 5

3.3 Earth Ground (GND) ..................................................................................... 5

Secondary Power Supply

4.1 Description .................................................................................................... 6

4.2 Battery Connection to XR2500F Command Processor panel ............................... 6

Two 866 NAC Modules

5.1 Description .................................................................................................... 7

5.2 Connection .................................................................................................... 7

5.3 Bell Silence/Bell Trouble ................................................................................. 7

LX-Bus™ Operation

6.1 Description .................................................................................................... 8

6.2 XR2500F On-board LX-Bus ............................................................................ 8

6.3 LX-Bus 481 Zone Expansion Interface Card ...................................................... 8

6.4 Installing the 481 Card ................................................................................... 8

893A Dual Phone Line Module

7.1 Description .................................................................................................... 9

7.2 Connection .................................................................................................... 9

7.3 Jumper Settings ............................................................................................ 9

7.4 Digital Dialer ................................................................................................. 9

7.5 Phone Line Monitor ........................................................................................ 9

7.6 Processor Fail Buzzer ..................................................................................... 9

7.7 J10 893A Connector ....................................................................................... 9

7.8 Ground start .................................................................................................. 9

7.9 Notication ..................................................................................................10

7.10 FCC Registration ..........................................................................................10

Fire Command Center

8.1 Description ...................................................................................................11

8.2 Connection ...................................................................................................11

8.3 Remote Fire Command Center .......................................................................11

Expansion

9.1 Zone Expansion ............................................................................................12

9.2 Output Expansion .........................................................................................12

Digital Monitoring Products XR2500F Installation Guide

taBle oF Contents

Accessory Devices

10.1 Wiring Diagram ............................................................................................13

10.2 Lightning Protection ......................................................................................13

10.3 Accessory Devices ........................................................................................14

10.4 Mounting Keypads and Zone Expansion Modules .............................................15

10.5 Connecting LX-Bus and Keypad Bus Devices ...................................................15

Battery Information

11.1 Battery Only Restart .....................................................................................16

11.2 Battery Replacement Period...........................................................................16

11.3 Discharge/Recharge ......................................................................................16

11.4 Battery Supervision .......................................................................................16

11.5 Battery Cutoff ...............................................................................................16

12.6 XR2500F Power Requirements .......................................................................16

11.7 XR2500F Standby Battery Calculations ...........................................................17

11.8 Standby Battery Selection .............................................................................19

Bell Output

12.1 Terminals 5 and 6 .........................................................................................20

Keypad Bus

13.1 Description ...................................................................................................20

13.2 Terminal 7 - RED ..........................................................................................20

13.3 Terminal 8 - YELLOW ....................................................................................20

13.4 Terminal 9 - GREEN ......................................................................................20

13.5 Terminal 10 - BLACK .....................................................................................20

13.6 J8 Programming Connection ..........................................................................20

13.7 OVC LED ......................................................................................................20

Smoke and Glassbreak Detector Output

14.1 Terminals 11 and 12 .....................................................................................21

14.2 Current Rating ..............................................................................................21

Powered Zones for 2-Wire Smoke Detectors

15.1 Terminals 25–26 and 27–28 ..........................................................................21

15.2 Compatible 2-Wire Smoke Detector Chart .......................................................22

Protection Zones

16.1 Terminals 13–24 ...........................................................................................23

16.2 Operational Parameters .................................................................................23

16.3 Zone Response Time .....................................................................................23

16.4 Keyswitch Arming Zone .................................................................................23

Dry Contact Relay Outputs

17.1 Description ...................................................................................................24

17.2 Contact Rating .............................................................................................24

17.3 Output Harness Wiring ..................................................................................24

J11 Annunciator Outputs

18.1 Description ...................................................................................................25

18.2 Model 300 Harness Wiring .............................................................................25

18.3 Model 860 Relay Module ...............................................................................25

J23 6-Pin Header

19.1 Description ...................................................................................................25

J22 LX-Bus Expansion Connector

20.1 Description ...................................................................................................26

20.2 LX-Bus Interface Cards ..................................................................................26

20.3 LX-Bus LEDs .................................................................................................26

20.4. OVC LED ........................................................................................................26

J21 Serial Connector

21.1 Description ...................................................................................................26

21.2 Serial Connector LEDs ...................................................................................26

XR2500F Installation Guide Digital Monitoring Products

iii

taBle oF Contents

J1 Ethernet Connector

22.1 Description ......................................................................................................27

22.2 Ethernet LEDs ..............................................................................................27

Reset and Tamper Headers

23.1 J16 Reset Header ........................................................................................27

23.2 J4 Tamper Header .......................................................................................27

Listed Compliance Specications

24.1 Introduction .................................................................................................28

Universal UL Burglary Specications

25.1 Introduction .................................................................................................28

25.2 Wiring..........................................................................................................28

25.3 Control Outside of Protected Area ..................................................................28

25.4 Police Station Phone Numbers .......................................................................28

25.5 Bypass Reports .............................................................................................28

25.6 System Maintenance .....................................................................................28

25.7 Listed Receivers............................................................................................28

25.8 Power Supply Supervision .............................................................................28

25.9 Wireless Tamper ...........................................................................................28

25.10 Wireless External Contact ..............................................................................28

25.11 Wireless Supervision Time .............................................................................28

25.12 Detect Wireless Jamming ..............................................................................28

Area Information

26.1 Ownership ...................................................................................................29

26.2 Annunciation ................................................................................................29

26.3 Trouble Display .............................................................................................29

26.4 Closing Wait .................................................................................................29

26.5 Local Bell Supervision ...................................................................................29

Household Burglar-Alarm System Units

ANSI/UL 1023

27.1 Audible Devices ............................................................................................29

27.2 Auxiliary Circuits ...........................................................................................29

27.3 Bell Cutoff ....................................................................................................29

27.4 Entry Delay ..................................................................................................29

27.5 Exit Delay ....................................................................................................29

27.6 Weekly Test ..................................................................................................29

27.7 Wireless Audible Annunciation Option ............................................................29

Central-Station and Proprietary Burglar-Alarm Units

ANSI/ UL 1610 AND ANSI/UL 1076

28.1 Opening/Closing Reports ...............................................................................29

28.2 Closing Wait .................................................................................................29

28.3 Entry Delay ..................................................................................................29

28.4 Exit Delay ....................................................................................................29

28.5 Proprietary Dialer .........................................................................................30

28.6 DACT Central Station ....................................................................................30

28.7 Bell Cutoff ....................................................................................................30

28.8 Standard or Encrypted Line Security...............................................................30

28.9 Wireless Audible Annunciation Option ............................................................30

28.10 Model 463G CELL Only, Standard or Encrypted Line Security ...........................30

28.11 Model 463G NET with CELL as Alternate Primary and Dialer Backup,

Standard or Encrypted Line Security .............................................................31

28.12 Model 463G NET with CELL as Backup and Adaptive Primary, Standard

or Encrypted Line Security ............................................................................31

Digital Monitoring Products XR2500F Installation Guide

taBle oF Contents

Holdup Alarm Units

ANSI/UL 636

29.1 ANSI/UL 1610 Required ................................................................................32

29.2 1100X Wireless Receiver ...............................................................................32

29.3 Wireless Supervision Time .............................................................................32

29.4 LED Display ..................................................................................................32

29.5 Jamming Detection .......................................................................................32

29.6 Local Alarm ..................................................................................................32

29.7 Message to Transmit .....................................................................................32

29.8 Wireless Audible Annunciation Option ............................................................32

Digital Burglar Alarm Communicator System Units

ANSI/ UL 1635

30.1 System Trouble Display .................................................................................32

30.2 Digital Dialer Telephone Number ....................................................................32

30.3 Test Time .....................................................................................................32

30.4 Closing Wait .................................................................................................32

Police Station Connected and Local Burglar Alarm Units

ANSI/UL 365

31.1 System Trouble Display .................................................................................32

31.2 Entry Delay ..................................................................................................32

31.3 Exit Delay ....................................................................................................32

31.4 Bell ..............................................................................................................33

31.5 Bell Cutoff ....................................................................................................33

31.6 Automatic Bell Test .......................................................................................33

31.7 Standard or Encrypted Line Security...............................................................33

31.8 Wireless Audible Annunciation Option ............................................................33

31.9 Model 463G CELL Only, Standard or Encrypted Line Security ...........................33

31.10 Model 463G NET with CELL as Alternate Primary and Dialer Backup,

Standard or Encrypted Line Security .............................................................34

31.11 Model 463G NET with CELL as Backup and Adaptive Primary, Standard

or Encrypted Line Security ............................................................................34

Police Station Connected and Local Burglar Alarm Units

ANSI/UL 609

32.1 Mercantile ....................................................................................................35

32.2 Entry Delay ..................................................................................................35

32.3 Exit Delay ....................................................................................................35

32.4 Bell ..............................................................................................................35

32.5 Wireless Audible Annunciation Option ............................................................35

Access Control System Units

ANSI/UL 294

33.1 Panel Designation .........................................................................................35

33.2 Compatible Devices ......................................................................................35

Universal Fire Alarm Specications

34.1 Introduction .................................................................................................36

34.2 Wiring..........................................................................................................36

34.3 Transformer .................................................................................................36

34.4 End-of-Line Resistor ......................................................................................36

34.5 System Trouble Display .................................................................................36

34.6 Fire Display ..................................................................................................36

34.7 Police Station Phone Number .........................................................................36

34.8 System Maintenance .....................................................................................36

34.9 Audible Alarm ...............................................................................................36

34.10 Fire Zone Programming .................................................................................36

34.11 Style D Zones ...............................................................................................36

34.12 Listed Receivers............................................................................................36

XR2500F Installation Guide Digital Monitoring Products

taBle oF Contents

Control Units for Fire-Protective Signaling Systems

ANSI/UL 864, NFPA 72

35.1 Power Supply ...............................................................................................37

35.2 Zone Restoral Reports ...................................................................................37

35.3 Power Fail Delay ...........................................................................................37

35.4 Sprinkler Supervisory ....................................................................................37

35.5 DACT Systems ..............................................................................................37

35.7 Local Protective Signaling Systems .................................................................37

35.8 Remote Station Protective Signaling Systems ..................................................37

35.9 Fire Protective Signaling Systems using Internet/Intranet Networks ..................37

35.10 Combination Systems ....................................................................................37

35.11 Remote Annunciators ....................................................................................37

35.12 Notication Appliances .................................................................................38

35.13 Cross Zoning ..................................................................................................38

35.14 Ground Fault ...............................................................................................38

Household Fire Warning System Units

ANSI/UL 985, NFPA 72

36.1 Bell Output Denition ....................................................................................38

36.2 Audible Devices ............................................................................................38

36.3 Auxiliary Circuits ...........................................................................................38

36.4 Bell Cutoff ....................................................................................................38

California State Fire Marshal Specications

37.1 Bell Output Denition ....................................................................................39

New York City (MEA) Specications

38.1 Introduction .................................................................................................39

38.2 Digital Dialer and Network Communication .....................................................39

38.3 Wiring..........................................................................................................39

38.4 Communication Programming ........................................................................39

38.5 Additional Requirements ...............................................................................39

Wiring Diagrams

39.1 Prewired 866 Modules with NAC Extender ......................................................40

39.2 Prewired 866 Class B Style W Modules using Single Notication Appliance ........40

39.3 Prewired 866 Class B Style W Modules with Multiple Notication Appliances ......41

39.4 Prewired 866 Class B Style W Modules with Dual Notication Appliance Circuits 42

39.5 867 Class B Style W using Single Notication Appliance ...................................43

39.6 867 Class B Style W Multiple Notication Appliance Circuit ...............................43

39.7 867 Class B Style W Multiple Notication Appliance Circuits .............................44

39.8 Dual Style D Zone Module Installation ............................................................45

39.9 Remote Station Reversing Relay Connection ...................................................46

39.10 Second LX-Bus™ with Auxiliary Power Supply .................................................47

39.11 LX-Bus™ Module Connection .........................................................................48

39.12 Model 860 Relay Module Connection ..............................................................49

39.13 Powered Burglary Devices ...............................................................................49

Revisions to This Document

OPERATING INSTRUCTIONS MODEL XR2500F PANELS

Mounting Instructions ..............................................................................................52

Listings and Approvals

Digital Monitoring Products XR2500F Installation Guide

This page intentionally left blank

XR2500F Installation Guide Digital Monitoring Products

IntRoduCtIon

Introduction

1.1 Overview

The DMP XR2500F Addressable Fire Alarm Control Panel (FACP) is an expandable 24 VDC Fire Alarm Control

with built-in DACT and LCD Fire Command Center keyboard with membrane keyswitch. A complete system

can provide:

• 574programmableinputsandoutputsforcommercialandindustrialrealarmservice.

• Eighton-boardgroundedzones

• Twoon-board12VDCClassB,StyeApoweredzones

Connecta12or24VDCregulated,powerlimitedpowersupplylistedforFireProtectiveSignalingSystems

todistributenoticationappliancepowerbetweenthetwoclassBstyleWNACoutputs.AdditionalNAC

outputs can be added with conventional supervision modules or addressable power supply/boosters.

AddressablesmokedetectorsandinputmodulesroundouttheXR2500Ftodeliveratrulyexibleand

expansiveredetectionandnoticationsystem.TheFireAlarmControlPanelisshippedpre-wiredinared

metalenclosurehousingthenecessarycomponentstomonitorandcontrolrealarmnoticationappliances.

Theenclosuredimensionsareasfollows:32”Hx14.5”Wx4”D.Thelidaddsabout0.5”toeachside.

1.2 System Components

TheXR2500FFACPconsistsofthefollowingpre-wiredcomponents:

• OneModelXR2500FCommandProcessorpanel •OneModel893ADualPhoneLinemodule

• TwoModel866ClassBStyleWNACmodules •OneModel630FPCBandmembraneswitch

• One16VAC,56VAtransformer •TwoModel305Plug-inRelays

• OneModel481ZoneExpansionInterfaceCard •OneMetalBackplate

1.3 Power Specications

TransformerInput: Primaryinput:120VAC,60Hz,Secondaryoutput:16VAC56VA

StandbyBattery: 12VDC,1.0AmpsMax.chargingcurrent

Auxiliary: 12 VDC output at 1.0 Amp Max*

BellOutput: 12VDCat.7AmpMax*

Note:ThecombinedAuxiliaryandBelloutputstotalcannotexceed1.9Ampswitha56VATransformer.

All circuits are inherent Power Limited except the red battery wire and AC terminal.

* For Commercial Fire installations, see the Compliance Instructions section.

1.4 Communication

Built-indialerornetworkcommunicationtoDMPModelSCS-1RReceivers

Built-inContactIDcommunicationtonon-DMPreceivers

893ADualPhoneLineModulewithphonelinesupervision

Can operate as a local panel

1.5 Panel Zones

Eight1kOhmEOLburglaryzones(zones1to8).Connectto869ClassAmoduleforburglaryapplications.

Two3.3kOhmEOLpoweredzonewithreset(zones9and10).

Note:UsethesuppliedDMPModel3111kOhmandDMPModel3013.3kOhmresistors.

1.6 Keypad Bus

Youcanconnectupto15ofthefollowingsupervisedkeypadsandexpansionmodulestothekeypadbus:

• AlphanumericFireCommandCentersorkeypads

• Four-and/orsingle-zoneexpansionmodules

• Single-zonedetectors

• Accesscontrolmodules

Digital Monitoring Products XR2500F Installation Guide

IntRoduCtIon

1.7 LX-Bus™

YoucanconnectthefollowingdevicestotheLX-Bus™providedbytheDMP481(supplied)orbythe462N,

481,462P,463G,and472InterfaceCardsuptothemaximumnumberofLX-Bus™addresses.SeeAccessory

Devices.

• Model521LXor521LXTSmokeDetectorswithCleanMe

• Sixteen-,eight-,four-and/orsingle-zoneexpansionmodules

• Single-zonedetectors

• Relayoutputexpansionmodules

• Graphicannunciatormodules

1.8 Outputs

TheXR2500Fprovidestwopre-installedModel305SinglePole,DoubleThrow(SPDT)relayoutputs,each

rated1Ampat30VDC(powerlimitedsourcesonly).

TheXR2500Falsoprovidesfourprogrammableopencollectoroutputsratedfor30VDC@50mAeach.The

opencollectoroutputsprovidegroundconnectionforapositivevoltagesource.AModel300OutputHarness

isrequiredtousetheseoutputsandmaybeconnectedtoaModel860RelayOutputModule.

1.9 Relays

TheXR2500FshipswithtwoModel305Relayspre-installedtoallowzonealarmcontrolforthe866NAC

Modules.Whenarealarmoccursthebelloutputisfactoryprogrammedtoturnonandprovidepowerto

thecontactsoftherelays.Speciczoneprogrammingdetermineswhetheroneorbothrelaysturnonsignal

voltagetothe866NACs.ThisallowscontroloftheNACsbyzone.

1.10 Zone Reference

TheXR2500Fhasbeenpre-wiredinthefactory.Therst866NACmoduleconnectstoZone1.Thesecond

866NACmoduleconnectstoZone2.

1.11 Compliance Instructions

ForapplicationsthatmustconformtoalocalauthoritiesinstallationstandardoraNationalRecognizedTesting

Laboratorycerticatedsystem,pleaseseetheWiringDiagramsforNoticationAppliancesandtheListed

ComplianceSpecicationssectionneartheendofthisguideforadditionalinstructions.

XR2500F Installation Guide Digital Monitoring Products

IntRoduCtIon

Mounting

2.1 Mounting the Enclosure

TheXR2500Fmustbemountedinasecure,

drylocationtoprotecttheunitfromdamage

duetotamperingandtheelements.The

enclosurecanbeeitherushmountedor

surfacemountedandincludesahingeddoor

with lock. The hole in the enclosure door

allows access to the Fire Command Center

withoutopeningthedoor.Figure1illustrates

themountingholelocationsforthepanel

enclosure.

Theenclosuredimensionsare32”tall,14.5”

wide,by4”deep.Thelidaddsabout0.5”to

each side.

2.2 Surface Mounting

The enclosure center hole should be attached

toawallstud.Duetotheenclosureweight,

especiallythebatteries,itisextremely

important to mount the enclosure on the

stud. Attach the two holes beside the center

holetosheetrocktosecureenclosure.When

mountingtheenclosure,besuretoleave

roomforthepaneldoortoswingopen.The

door lock should be easily accessible.

2.3 Flush Mounting

Theenclosurecanalsobeushmounted.Use

1”screwstosecuretheenclosurebetween

twostudsusingthetwosetsofholeson

thesidesoftheenclosure.Usethetopand

bottomholestosecuretohorizontalstuds,if

necessary.

2.4 Fire Command Center LCD

Keyboard

A Fire Command Center LCD Keyboard

hasbeenfactoryinstalledontheXR2500F

enclosure. A keyswitch has also been

installedandpre-wiredtotheleftofthe

keyboard. The user can turn the keyswitch to

enablethefourfunctionkeyswithoutopening

the enclosure door.

2.5 Metal Backplate

The XR2500F components are pre-wired

and installed on a metal backplate. The

backplatecanbeeasilyremovedtokeepcomponentssafeduringpre-wireactivities.

Remove AC and battery power from the XR2500F panel before removing the backplate. Disconnect all

battery,transformer,andtheFireCommandCenterLCDkeyboardwires.Fromthepanel,disconnecttheAC

wiresfromterminals1and2.Disconnectthebatterywireseitherfromthebatteriesorthepanelterminals

3and4.Finally,disconnectthekeyboardwiresfrompanelterminals7,8,9,and10.

Removethescrewssecuringthebackplatetotheenclosure.Loosenthetwotopscrewsthatthebackplate

hangson.Afterlooseningandremovingthescrews,liftthebackplateupslightlyandpullthebackplate

towardyou.Whenreinstallingthebackplate,besureallconnectionsaresecure.

Figure2illustratesthebackplateandthecomponents.Thebackplateisshowninlightgray.

3/4" X 1/2" Knockouts

Hole for Flush

Mounting

Holes for Surface Mounting

Holes for 1" screws for

Flush Mounting

Battery Shelf

Hole for Flush Mounting

Additional Holes for Surface Mounting

Figure 1: Mounting the XR2500F Enclosure

Digital Monitoring Products XR2500F Installation Guide

IntRoduCtIon

2.6 Wiring Diagram

TheXR2500Fsystembelowshowsthecomponentlayout.Thewiresshowninthisguidehavebeenfactory

installedandconnected.Thedashedlinesrepresentwiresrunningunderneathorbehindacomponent.

Detailedwiringdiagramsforeachsuppliedcomponentappearinfollowingsectionsofthisguide.

12345 678 10 11 12 13 14 15 16 17 18 199202122232425262728

+B BELL GND SMK GNDRED YEL GRN BLK Z1 Z2 Z3 Z4 Z5 Z6 Z7 Z8 Z9+ Z9– Z10+ Z10–AC –B GND GND GNDGND

Output 1Output 2

Phone

Line

J22

Battery

Start

Power

LED

PROG

Tamper

J16

Reset

Out1 Out2

Outputs 3-6

Ethernet

Link LED

Power LED

OVC

XR2500F

Command

Processor™

Panel

J6 Expansion

Card Slot

TYPES OF SERVICE

Suitable for Mercantile Local

and Police Station Connect.

Suitable for Proprietary, PPU,

other technologies, local.

Suitable for Signaling and

Remote Station PPU DACT

Service.

Suitable for manual fire alarm,

automatic fire alarm, sprinkler

supervisory, or water flow

alarm.

Suitable for Standard or

Encrypted Central Station with

NET or CELL communication.

Suitable for Household Fire and

Household Burglary.

Suitable for Coded and March

Time signaling.

NFPA 72

This equipment should be

installed in accordance with

the National Fire Alarm Code,

ANSI/NFPA 72 (National Fire

Protection Association,

Batterymarch Park, Quincy, MA

02269). Printed information

describing proper installation,

operation, testing,

maintenance, evacuation

planning, and repair service is

to be provided with this

equipment.

Zones 9, 10, and all expanded

zones are suitable for Class B

(as applicable for the initiating

and signaling line circuits per

ANSI/UL 864 Table 48.2 or

48.3). Installation limits under

local Authority Having

Jurisdiction (AHJ).

Control Unit

Delay

Smoke

Model

Detector

Delay

Verification

Zones

WARNING

THIS UNIT MAY BE PROGRAMMED TO USE AN ALARM VERIFICATION FEATURE THAT RESULTS IN DELAY OF THE

SYSTEM ALARM SIGNAL FROM THE INDICATED CIRCUITS. THE TOTAL DELAY (CONTROL UNIT PLUS SMOKE

DETECTORS) SHALL NOT EXCEED 60 SECONDS. NO OTHER SMOKE DETECTOR SHALL BE CONNECTED TO THESE

CIRCUITS UNLESS APPROVED BY THE LOCAL AUTHORITY HAVING JURISDICTION (AHJ).

See LT- 0759, 893A

Dual Phone Line

Module section

for complete 893A

information.

Refer to LT-0759, Standby

Battery Selection section

for battery standby times and

numbers of batteries to use.

See LT- 0759, Two 866

NAC Modules section for

complete 866 information.

866

Module

866

Module

+-+

12 VDC battery

Two 12 VDC batteries

connected in parallel with a

Model 318 Dual Battery

Harness. See Secondary

Power Supply section.

XR2500F Secondary Power Supply

1 Amp maximum charge current.

Use only 12 VDC rechargeable batteries.

Replace every 3 to 5 years.

12 VDC battery

Black

Red

To Fire Command Center on enclosure door

From XR2500F

panel to 12 VDC.

56 VA

Transformer

GROUND

GREEN

GREEN/

YELLOW

WHITE

BLACK

WHITE

BLACK

To Telco

To Notification

Appliances

Battery Compartment

10K EOL

16 VAC

Expansion Zones

Connected to

Enclosure Door

Use Marking

Commercial and Residential

Fire, Burglar, Holdup, and

Access Protected Premise Unit

Figure 2: XR2500F System

XR2500F Installation Guide Digital Monitoring Products

IntRoduCtIon

AC Connection

3.1 Transformers and AC Power Connection

The AC connection should be completed by a licensed electrician.

Never share the Fire Alarm Control Panel circuit with any other equipment.

TheXR2500Fcomessuppliedwitha16VAC56VAtransformer.The16VACtransformerwhiteleadsandblack

leadsmustbeconnectedtoanunswitched120VAC60Hzpowersourcewithatleast.87Aavailable.Observe

wirecolorsandconnectthetransformerwires:

 TheBlacktransformerwirestotheBlack120VACwire

 TheWhitetransformerwirestotheWhite120VACwire

 TheGreen/Yellowgroundwiretotheelectricalground

56 VA

Transformer

To XR2500F Panel

Violet

Terminal 1

Gray

Terminal 2

16 VAC

56 VA

Transformer

L-Bracket

Bracket

Nut

Bracket

Nut

GROUND

GREEN

GREEN/

YELLOW

WHITE

BLACK

WHITE

BLACK

Connected to

Enclosure Door

Figure 3: Transformers and AC Power Connection

Always ground the panel before applying power to any devices! Use18AWGorlargerforallpower

connections.TheXR2500Fmustbeproperlygroundedbeforeconnectinganydevicesorapplyingpower

tothepanel.PropergroundingprotectsagainstElectrostaticDischarge(ESD)thatcandamagesystem

components.

3.2 16 VAC Transformer

The16VAC56VAtransformersuppliespowertotheXR2500Fpanelandisfactorypre-wired.SeeFigure3:

TransformersandACPowerConnection.AlsorefertoFigure11:XR2500FPanelWiringDiagram.

3.3 Earth Ground (GND)

TheXR2500Fterminal4mustbeconnectedtoearthgroundusing14AWGorlargerwiretoprovideproper

transientsuppression.DMPrecommendsconnectingtoacoldwaterpipe,buildingground,orgroundrod

only.Donotconnecttoanelectricalgroundorconduit,sprinklerorgaspipes,ortoatelephonecompany

ground.

Digital Monitoring Products XR2500F Installation Guide

IntRoduCtIon

Secondary Power Supply

4.1 Description

TheXR2500Fsystemincludespre-wiredcablesforconnecting12VDCbatterytotheXR2500Fpanel.Observe

polaritywhenconnectingallbatteries.

Use sealed lead-acid batteries only.UsetheDMPModel367,368,369,365,366,12VDCsealedlead-acid

rechargeablebatteries.BatteriessuppliedbyDMPhavebeentestedtoensureproperchargingwithDMP

products.

GelcellbatteriescannotbeusedwiththeXR2500Fpanel.

4.2 Battery Connection to XR2500F Command Processor panel

For12VDCbatteryoperationtotheXR2500F,connecttheblackbatteryleadtothebatterynegative

terminal. The black battery wire connects to XR2500F panel terminal 4.

Connect the red battery lead to the battery positive terminal. The red battery wire connects to XR2500F

panelterminal3.SeeFigure11andFigure2.

AddasecondbatteryinparallelusingtheDMPModel318DualBatteryHarness.Whenwiringtwobatteries

withtheModel318DualBatteryHarness,plugtheDualBatteryHarnessredmaleendintothepanelred

femalebatterylead.PlugtheDualBatteryHarnessblackmaleendintothepanelblackfemalebattery

lead.AttachbothDualWiringHarnessfemaleleadstothetwobatteriesasdescribedabove.SeeTable3:

BatteryCalculations.

XR2500F Installation Guide Digital Monitoring Products

IntRoduCtIon

Two 866 NAC Modules

5.1 Description

Each866providesonestyleWindicatingcircuitforsupervisinglistedpolarizednoticationappliances,

suchasbells,strobes,andhorns.SeeTable1:NoticationAppliancesforalistofapprovednotication

appliances.

5.2 Connection

Each866moduleispre-installedontheremovablebackplateusingthestandardthree-holeconguration.

Themodulesarefactorypre-wiredtoeachotherandtheXR2500Fpanel.Refertothegurebelowandto

Figure2:XR2500FSystemforwiringconnections.

Connecta12or24VDCregulated,powerlimitedpowersupplylistedforFireProtectiveSignalingSystemsto

terminals2and4ofeachmoduletoprovideNoticationappliancepower.Connectnoticationappliances

toterminals5and6ofeachmodule.Eachmoduleprovidesazoneofnoticationandcanbeactivated

separately.

1 AUX PWR

2 GND

3 Alarm In

4 Bell PWR In

5 Bell Out +

6 Bell Out -

7 Bell Trouble

8 Bell Trouble

866

Module #1

Normal/Silence Switch

1 AUX PWR

2 GND

3 Alarm In

4 Bell PWR In

5 Bell Out +

6 Bell Out -

7 Bell Trouble

8 Bell Trouble

866

Module #2

Normal/Silence Switch

To XR2500F Output #1 (J2 pin #2)

To XR2500F terminal 13 (Zone 1)

To XR2500F terminal 7

To 24 VDC Power Supply DC -

To XR2500F Output #2 (J2 pin #5)

To 24 VDC Power Supply DC +

To XR2500F terminal 15 (Zone 2)

To 24 VDC Power Supply

Listed, Polarized

Notification Appliances

See the Notification

Appliance section

Listed, Polarized

Notification Appliances

See the Notification

Appliance section

Pre-installed 1K EOL

Figure 5: 866 Modules Wiring

5.3 Bell Silence/Bell Trouble

Abellsilenceswitchonthe866moduleisprovidedtopreventindicatingdevicesfromsoundingduring

systemtesting.WhentheSilencepositionisselected,a15-seconddelayoccursbeforethe866belltrouble

contacts(terminals7and8)open.SelecttheNormalpositionaftertestingtoreturnthe866moduleto

normal operation.

Digital Monitoring Products XR2500F Installation Guide

IntRoduCtIon

LX-Bus™ Operation

6.1 Description

TheXR2500FCommandProcessor™panelsupportsLX-Busoperationdirectlyfromthepanel.EachLX-Bus

circuitprovides100additionalzones.UseJ22LX-BusHeaderfortherst100zones.Usetheinstalled481

ZoneExpansionInterfaceCardforthenext100zones.Thisprovidesatotalof200expansionzones.To

installuptofouradditionalInterfaceCardsuseaModel461InterfaceAdaptorCard.

6.2 XR2500F On-board LX-Bus

ToenableJ22tooperateasanLX-Bus,placeajumperonthetwopinsnexttotheletter“L”ontheJ23

6-Pinheader.WhenusingJ22asanLX-Bus,connectaDMPModel3004-wireHarnesstotheJ224-pin

headerlabeledLX-BUS.Thisprovidestherst100LX-Buszonesnumbered500-599.Respectwirecolors

whenconnectingdevicesanduseallfourwires.ResetthepanelusingtheJ16jumpertoactivateLX-Bus

operation.SeeConnectingLX-BusandKeypadDevicessectionformaximumwiringdistances.

Note:DoNOTuseshieldedwirewhenusingtheLX-Bus.DoNOTconnectthewiresfromthe4-wireharness

to the panel terminals.

6.3 LX-Bus 481 Zone Expansion Interface Card

The481ZoneExpansionInterfaceCardprovidesanadditional100zonestotheXR2500F.Whenusedin

conjunctionwiththeon-boardJ22LX-Busthe481LX-Buszonesarenumbered600to699.

6.4 Installing the 481 Card

Remove AC and battery power from the XR2500F panel and ground yourself before handling and

installing the 481 Card.

1.Alignthe481Card50pinconnectorwiththeXR2500FpanelJ6connector.

2.Pressthe481ontotheJ6connectorwhileapplyingevenpressuretobothsides.

J6 Interface Card

Connector

22 23

26 27

Z8 Z9+

Z9-

Z10+

Z10-

GND

481 Zone

Expansion

Interface

Card

Red—Auxiliary Power

Yellow—Data In

Green—Data Out

Black—Ground

Zone Expansion

Harness Connectors

To LX-Bus Modules

Command Processor

Panel

Figure 6: 481 Wiring

XR2500F Installation Guide Digital Monitoring Products

IntRoduCtIon

893A Dual Phone Line Module

7.1 Description

The893Aisadualtelephonelinesupervisionmodulethatallowsthepaneltoindicateaphonelinefailure

tothepremisesandthecentralmonitoringstation.Afterthe893Asensesafailureonthemainline,it

switchestothebackup,orsecondary,phoneline.The893Ainstallsontheremovablebackplateabovethe

XR2500F circuit board.

7.2 Connection

Thepre-wired893AconnectsthepaneltothepublictelephonenetworkthroughaninstalledDMP356RJ

CablebetweentheXR2500FpanelJ3connectorandthe893AModuleJ3connectorlabeledPANEL.

MPX

PANEL

MAIN

BACKUP

P10

Factory pre-wired

to XR2500F panel

Phone Jack

Connector, J3

To Primary

telephone line

To Secondary telephone line

Communication Jumpers:

Both Set both Jumpers

Processor

Stopped Buzzer

Factory pre-wired

to XR2500F panel

J10 Connector

893A Dual Telephone Line Module

Figure 8: 893A Dual Phone Line Module Wiring

7.3 Jumper Settings

The893Amodulehastwosetsofjumpers.BothcommunicationjumpersmustbesetforDD(digitaldialer)

operation.Donotsetthe893AjumpersnexttoMPX.The893AModulesupportsmultiplexoperation,but

the XR2500F panel does not.

7.4 Digital Dialer

Youcancongurethe893Atoprovidetwolinesofdigitaldialer.Maximumlineimpedanceis100Ohms.The

XR2500FispresetatthefactoryforDigitalDialer.TheMainmodularjack(J4)isusedfortheprimarydigital

dialerline.TheBackupmodularjack(J5)isusedforthesecondarydigitaldialerline.

7.5 Phone Line Monitor

The893Ausesaphonelinemonitorforthemainandbackupphonelines.Whensendingareport,the893A

veriesthemainphonelineisworkingbeforesendingdata.Ifthelineisbad,themoduleteststhebackup

phoneline.The893Asendsthereportontherstworkingphoneline.

The phone line monitor has a two-minute trouble delay and a one-minute restore delay. Phone line trouble

isdisplayedintheFireCommandCenterLCDStatusListasaSystemTrouble.TheFireCommandCenter

LCDisfactoryprogrammedtodisplaysystemtroublesintheStatusList.

7.6 Processor Fail Buzzer

The893AmodulealsomonitorsthepanelCPUandsoundsatroublebuzzerwhenevereitherthepanel

processorisresetusingJ16ortheprocessorstopsfunctioning.

7.7 J10 893A Connector

The893ADualPhoneLineModuleconnectstotheXR2500FJ10.Refertothe893AInstallationSheet

(LT-0135)forcompleteinformation.

7.8 Ground start

Ground start phone service cannot be used on commercial or residential re applications.

Digital Monitoring Products XR2500F Installation Guide

IntRoduCtIon

7.9 Notication

Theusermustnotrepairregisteredterminalequipment.Incaseoftrouble,immediatelyunplugthedevice

fromthetelephonejack.Thefactorywarrantyprovidesforrepairs.Registeredterminalequipmentmay

notbeusedonpartylinesorinconnectionwithcointelephones.Notifythetelephonecompanywiththe

followinginformation:

a. The particular line(s) where the service is connected

b.TheFCCregistrationnumber

c.Theringerequivalence

d.Thedevicemake,model,andserialnumber(seetheserial#stickeronthepanel)

7.10 FCC Registration

TheModelXR2500FcomplieswithPart68oftheFCCrulesandtherequirementsadoptedbytheACTA.On

theoutsideoftheenclosureofthisequipmentisalabelthatcontains,amongotherinformation,aproduct

identierintheformatUS:CCKAL00BXR500.Ifrequestedthisnumbermustbeprovidedtothetelephone

company.

Aplugandjackusedtoconnectthisequipmenttothepremiseswiringandtelephonenetworkmustcomply

withtheapplicableFCCPart68rulesandrequirementsadoptedbytheACTA.Seeinstallationinstructions

fordetails.

TheRingerEquivalenceNumber(REN)isusedtodeterminethenumberofdevicesthatmaybeconnected

toatelephoneline.ExcessiveRENsonatelephonelinemayresultinthedevicesnotringinginresponseto

anincomingcall.Inmostbutnotallareas,thesumofRENsshouldnotexceedve(5.0).Tobecertainof

thenumberofdevicesthatmaybeconnectedtoaline,asdeterminedbythetotalRENs,contactthelocal

telephone company.

IftheXR2500Fcausesharmtothetelephonenetwork,thetelephonecompanywillnotifyyouinadvance

thattemporarydiscontinuanceofservicemayberequired.Butifadvancenoticeisn’tpractical,the

telephonecompanywillnotifythecustomerassoonaspossible.Also,youwillbeadvisedofyourrightto

leacomplaintwiththeFCCifyoubelieveitisnecessary.

Thetelephonecompanymaymakechangesinitsfacilities,equipment,operationsorproceduresthatcould

affecttheoperationoftheequipment.Ifthishappensthetelephonecompanywillprovideadvancenotice

inorderforyoutomakenecessarymodicationstomaintainuninterruptedservice.

IftroubleisexperiencedwiththeModelXR2500F,forrepairorwarrantyinformation,pleasecontactDMPat

theaddressandtelephonenumberlistedonthebackofthisdocument.Iftheequipmentiscausingharmto

thetelephonenetwork,thetelephonecompanymayrequestthatyoudisconnecttheequipmentuntilthe

problem is resolved.

Ifyourpremiseshasspeciallywiredalarmequipmentconnectedtothetelephoneline,ensurethe

installationoftheXR2500Fdoesnotdisableyouralarmequipment.Ifyouhavequestionsaboutwhatwill

disablealarmequipment,consultyourtelephonecompanyoraqualiedinstaller.

Caution:Toensureproperoperation,thisequipmentmustbeinstalledaccordingtotheinstallation

instructionsinthismanual.Toverifythattheequipmentisoperatingproperlyandcansuccessfullyreportan

alarm,thisequipmentmustbetestedimmediatelyafterinstallation,andperiodicallythereafter,according

tothetestinstructionsinthisdocumentandtheXR500SeriesProgrammingGuide(LT-0679).Additionally,

vericationofLineSeizecapabilityshouldbemadeimmediatelyafterinstallation,andperiodically

thereafter,inordertoensurethatthisequipmentcaninitiateacallevenwhenotherequipment(telephone,

answeringsystem,computermodem,etc.)connectedtothesamelineisinuse.

XR2500F Installation Guide Digital Monitoring Products

IntRoduCtIon

Fire Command Center

8.1 Description

TheXR2500FprovidesanLCDdisplayand20-keykeyboardforprogrammingandsystemuseroperation.The

Fire Command Center is installed on the XR2500F enclosure door. A keyswitch is installed and pre-wired

totheleftofthekeyboard.Theusermustturnthekeyswitchtoenablethefourfunctionkeys.Seethe

illustration below.

POWER

TROUBLE

ALARM

COMMAND

1234

5678

ABC DEF GHI JKL

MNOPQR STU VWX

ENABLE

SILENCE

RESET

TEST

DRILL

Fire Command Center

Figure 10: Fire Command Center LCD and Keyboard

8.2 Connection

Thedisplayandkeyboardarefactorypre-wiredtotheXR2500Fpanelterminals7,8,9,and10.Forstandby

batterycalculations,thedisplaydraws92mAofcurrentinnormalstandbyoralarmcondition.SeePanel

StandbyBatteryCalculations.Thekeyswitchispre-wiredtothemembranekeyboard.

8.3 Remote Fire Command Center

UptofteenModel630FRemoteFireCommandCentersmayberemotelyattachedtotheXR2500Fsystem.

Seethe630FInstallationGuide(LT-0741)foradditionalinformation.

Digital Monitoring Products XR2500F Installation Guide

IntRoduCtIon

Expansion

9.1 Zone Expansion

Upto574reandburglaryzonesareavailableontheXR2500FusingDMPSecurityCommandkeypadremote

zonecapabilityandzoneexpansionmodules.Thepanelkeypaddatabussupportsuptosixteensupervised

deviceaddresseswitheachaddresssupportinguptofourprogrammableexpansionzones.

Upto500zonesareavailableusingtheon-boardLX-Busalongwithadditionalexpansionmodules.Usethe

461InterfaceAdaptor,462N,462P,463G,or481interfacecards,andanycombinationofsixteen,eight,four,

andsinglepointzoneexpandermodulesandsinglepointLX-Busdetectors.

Combinedcurrentrequirementsofadditionalmodulesmayrequireanadditionalpowersupply.Seethe

710/710FBusSplitter/RepeaterInstallationGuide(LT-0310).RefertotheStandbyBatteryCalculations

sectionwhencalculatingpowerrequirements.

Note:DonotuseshieldedwireforLX-BusorKeypadBuscircuits.

9.2 Output Expansion

Note:DonotuseshieldedwireforLX-BusorKeypadBuscircuits.

InadditiontothetwoSPDTrelaysandfourprogrammableopencollectoroutputsontheXR2500F,youcan

alsoconnectupto25programmableModel716OutputExpansionModulestoeachLX-Bus.Thesemodules

canprovideanadditional500programmableSPDTrelays.

TheXR2500Fprovides100OutputSchedulesyoucanuseforprogrammingthe716toperformavarietyof

annunciationandcontrolfunctions.Youcanalsoassignthe716outputstoanypanelOutputOptionssuchas

FireAlarm,CommunicationFail,orPhoneTroubleOutputs.Refertothe716InstallationGuide(LT-0183).

TheLX-Bus™alsosupportstheModel717GraphicAnnunciatorModule.Each717modulesupplies20

switchedgroundoutputsthatfollowthestateoftheirassignedzones.

Note:The717supportsthersteightkeypadbuszones.TofollowKeypadBuszonesninethrough16,install

multiple716modules.Refertothe717InstallationGuide(LT-0235)and716InstallationGuide(LT-0183).

Page is loading ...

DMP Electronics XR2500F, Addressable Fire Alarm Control Panel XR2500F User manual

Related papers

Other documents