AVer AVerVision SPB370 User manual

FCC NOTICE (Class A)

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

Federal Communications Commission Statement

NOTE- This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by tuning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:



Reorient or relocate the receiving antenna.



Increase the separation between the equipment and receiver.



Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.



Consult the dealer or an experienced radio/television technician for help.

Class A ITE:

Class A ITE is a category of all other ITE which satisfies the class A ITE limits but not the

class B ITE limits. Such equipment should not be restricted in its sale but the following

warning shall be included in the instructions for use:

Warning - This is a class A product. In a domestic environment this product may cause

radio interference in which case the user may be required to take adequate measures.

CE Class A (EMC)

This product is herewith confirmed to comply with the requirements set out in

the Council Directives on the Approximation of the laws of the Member States

relating to Electromagnetic Compatibility Directive 2004/108/EEC.

Warning - This is a Class A product. In a domestic environment this product may cause

radio interference in which case the user may be required to take adequate measures to

correct this interference.

DISCLAIMER

No warranty or representation, either expressed or implied, is made with respect to the

contents of this documentation, its quality, performance, merchantability, or fitness for a

particular purpose. Information presented in this documentation has been carefully

checked for reliability; however, no responsibility is assumed for inaccuracies. The

information contained in this documentation is subject to change without notice.

In no event will AVerMedia be liable for direct, indirect, special, incidental, or

consequential damages arising out of the use or inability to use this product or

documentation, even if advised of the possibility of such damages.

TRADEMARKS

AVerVision is registered trademarks of AVerMedia Information, Inc. IBM PC is a

registered trademark of International Business Machines Corporation. Macintosh is a

registered trademark of Apple Computer, Inc. Microsoft is a registered trademark and

Windows is a trademark of Microsoft Corporation. All other products or corporate names

mentioned in this documentation are for identification and explanation purposes only, and

may be trademarks or registered trademarks of their respective owners.

COPYRIGHT

be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into

any language in any form by any means without the written permission of AVerMedia

INFORMATION, Inc.

THE MARK OF CROSSED-OUT WHEELED BIN INDICATES THAT THIS

PRODUCT MUST NOT BE DISPOSED OF WITH YOUR OTHER

HOUSEHOLD WASTE. INSTEAD, YOU NEED TO DISPOSE OF THE

WASTE EQUIPMENT BY HANDING IT OVER TO A DESIGNATED

COLLECTION POINT FOR THE RECYCLING OF WASTE ELECTRICAL

AND ELECTRONIC EQUIPMENT. FOR MORE INFORMATION ABOUT

WHERE TO DROP OFF YOUR WASTE EQUIPMENT FOR RECYCLING,

PLEASE CONTACT YOUR HOUSEHOLD WASTE DISPOSAL SERVICE OR

THE SHOP WHERE YOU PURCHASED THE PRODUCT.

Remote Control Battery Safety Information

- Store batteries in any cool & dry place.

- Do not dispose used batteries in domestic waste. Dispose batteries at special

collection points or return to stores if applies.

- Remove the batteries if they are not in use for long period of time. Battery

leakage and corrosion can damage the remote control, dispose batteries safely.

- Do not mix and use old and new batteries.

- Do not mix and use different types of batteries: alkaline, standard (carbon-zinc)

or rechargeable (nickel-cadmium).

- Do not dispose batteries in a fire.

- Do not attempt to short circuit the battery terminals.

Remote Cont rol Class 2 La ser Product

LASER RADIATION

DO NOT STARE INTO THE BEAM

CLASS 2 LASER PRODUCT

Table of Contents

Introduction

.................................................................................... 1

Package Contents

........................................................................... 1

Optional Accessories

...................................................................... 1

AVerMedia® AVerVision SPB370 Parts

............................................ 2

Making the Connections

.................................................................. 3

Rear Panel........................................................................................................ 3

Left Panel.......................................................................................................... 3

Right Panel ....................................................................................................... 4

Connecting a VGA, Mac Monitor or LCD/DLP Projector .................................. 4

Connecting a Monitor or LCD/DLP Projector with DVI interface ...................... 5

Connecting a TV ...............................................................................................5

Connecting the Power Adapter......................................................................... 6

Connecting a Computer....................................................................................6

Connecting a Microphone................................................................................. 6

Connecting to Audio Output Device .................................................................7

Connecting a Computer via USB Connection .................................................. 7

Inserting and Ejecting a SD Card .....................................................................8

Setting Up SPB370

.......................................................................... 8

Arm ...................................................................................................................8

Camera Head ................................................................................................... 8

Overhead Light .................................................................................................9

Infrared Sensor .................................................................................................9

Light Box...........................................................................................................9

Anti-glare .......................................................................................................... 9

Microscope Connection ..................................................................................10

Control Panel Light Color ............................................................................... 10

Using Web Browser to Control SPB370

.......................................... 10

Using the Infrared Remote Control

................................................. 11

Touch Button Control Panel

.......................................................... 13

Using AVerVision SPB370 as a Mass Storage

................................ 14

OSD Navigation Tree

..................................................................... 15

Menu Functions

............................................................................ 16

Technical Specifications

................................................................ 19

RS-232C Diagram Connection

....................................................... 20

RS-232C Cable Spec

...................................................................... 20

RS-232C Transmission Spec

......................................................... 20

RS-232C Communication Format

................................................... 20

Send Command Format ................................................................................. 20

Set Value Format............................................................................................ 21

Get Value Format ...........................................................................................22

Troubleshooting

............................................................................ 22

Limited Warranty....................................................................... 23

1

P

a

c

k

a

g

e

C

o

n

t

e

n

t

s

Your AVerMedia

®

AVerVision SPB370 package contains the following:

Remote Control

(batteries included)

AVerMedia

®

AVerVision SPB370

User Manual

D

U

S

T

C

O

V

E

R

Dust Cover

Anti-glare Sheet

Installation CD

Power Adapter

Power Cord

* The power cord varies depending on the

standard power outlet of the country where it is

sold.

RCA Cable (2X)

S-Video Cable

RGB Cable

USB Cable

O

p

t

i

o

n

a

l

A

c

e

s

o

r

i

e

s

I

n

t

r

o

d

u

c

t

i

o

n

Thank you for purchasing

the AVerMedia

®

AVerVision SPB370. This

document camera

displays documents,

negatives, transparencies

and 3D objects onto a TV,

LCD or DLP projector

making demonstrations a

snap.

The advanced features of

the AVerVision SPB370

make it a versatile and

multi-functional product.

Integrated with the new

powerful zoom feature,

AVEROPTICAL Zoom is a

combination of optical

zoom with AVERZOOM.

AVERZOOM is an

AVerMedia patented

technology which digitally

zooms in and pans on an

image while maintaining

optical zoom image

quality. You can save still

images in the built-in

memory, or SD memory

card. When connected to

a computer via USB

connection and with the

bundled software, you can

capture and save still

images and video clips to

your hard drive directly. It

also comes with a fully-

featured remote control.

34mm Microscopic

Adapter

28mm Microscopic

Adapter

2

A

V

e

r

M

e

d

i

a

®

A

V

e

r

V

i

s

i

o

n

S

P

B

3

7

0

P

a

r

t

s

The illustrations below identify the parts of SPB370.

1. Overhead light

2. Camera head

3. Camera lens

4. Left panel

5. Control panel

6. Light box

7. Arm

8. Label slot

9. IR sensors

10. Rear panel

11. Right panel

12. MIC IN port

13. Video output switch

14. Light box power

button

15. DC 12V port

16. RGB output port

17. S-Video output port

18. Video output port

(RCA/Composite)

19. DVI-I output port

20. USB port

21. SD card slot

22. RGB IN 1 port

23. RGB IN 2 port

24. Audio out port

25. RS-232 port

26. Ethernet (RJ-45) port

27. Antitheft slot

(1

)

(4

)

(6

)

(5

)

(2

)

(3

)

(11

)

(7)

(9

)

(8

)

(10

)

E

T

H

E

R

N

E

T

R

S

-

2

3

2

R

G

B

I

N

1

R

G

B

I

N

2

A

U

D

I

O

U

T

I

O

I

O

I

Left Pane l

(12)

(13)

(14)

LIGHT BOXMIC IN VIDEO OUTPUT

SPB370

TV RGB

LIGHT BOXMIC IN VIDEO OUTPUT

TV RGB

Rea r Pane l

(15) (16) (20) (21)(19)(18)(17)

RGB

OUTPU T

DC 12V VIDE O

OUTPUT

S-VIDE O

OUTPU T

DVI-I O UTPUT USB SD C ARD

ETHERNETRS-232RGB IN 1RGB IN 2AUDIO OUT

IOIOI

ETHERNETRS-232RGB IN 1RGB IN 2AUDIO OUT

IOIOI

Righ t Pane l

(25)

(26)

(27)

(22)

(23)

(24)

3

M

a

k

i

n

g

t

h

e

C

o

n

e

c

t

i

o

n

s

The ports on the rear, left and right panel of SPB370 enable you to connect the unit to a

computer, graphics display monitor or LCD/DLP projector, TV or other device. Illustrated

below are the ports that are located at the rear and right panel of SPB370 with their

corresponding labels.

Rear Panel

(1) (2) (6) (7)(5)(4)(3)

RGB

OUTPUT

DC 12V VIDEO

OUTPUT

S-VIDEO

OUTPUT

DVI-I OUTPUT USB SD CARD

Name Function

(1) DC 12V

: Connect the power adapter into this port.

(2) RGB output

: Output the signal from the camera, RGB IN port, or the

captured images from the memory source on a VGA/Mac

monitor or LCD/DLP projector.

(3) S-Video output

: Output the signal from the camera or the captured images

from the memory source on TV or Video equipment.

(4) Video output

(RCA/Composite)

: Output the signal from the camera or the captured images

from the memory source on TV or Video equipment.

(5) DVI-I output

: Output the signal from the camera, RGB IN port, or the

captured images from the memory source on a VGA/Mac

monitor or LCD/DLP projector with DVI-I interface. If the

display device does not support DVI-I, it can only display

the signal from the camera and the captured images.

(6) USB

: Use SPB370 as a USB Camera or Mass Storage to

transfer the captured images from SPB370 memory

source to PC.

(7) SD card

: Insert the SD card with the label facing up. It can support

16MB~2GB card capacity and only accepts FAT16

formatted card.

Left Panel

(1) (3)(2)

LIGHT BOXMIC IN VIDEO OUTPUT

SPB370

TV RGB

Name Function

1. MIC IN

: Connect a Ф 6.3mm jack microphone into this port.

2. VIDEO OUTPUT

: Select to output video signal between RGB (RGB & DVI-I)

or TV (Composite Video/S-Video) display output.

3. LIGHT BOX

: Turn on/off the

light box.

4

Right Panel

(1) (2) (3)(4) (5

)

ETHERNETRS-232RGB IN 1RGB IN 2AUDIO OUT

IOIOI

Name Function

(1) Audio Out : Output the microphone audio signal to an amplifier, on TV, or

AV equipment audio input port. Or, Use an RCA Jack to 3.5mm

Mono Plug Adapter to connect to computer line-in port.

(2) RGB IN 1 &

RGB IN 2

: Takes as input the signal from a computer or other sources

and pass it through to the RGB Output and DVI-I port only.

Connect this port to the VGA output port of the computer.

(3) RS-232 : Receive command from the computer to operate SPB370.

Connect this port to the RS-232 port of the computer.

(4) Ethernet : Use an RJ-45 Ethernet cable and connect it to RJ-45 Ethernet

port. This connection allows using any Web browser to access

the embedded web server and remotely control SPB370. Make

sure SPB370 is connected to IP-based network. Also see

“Using Web Browser to Control SPB370”.

(5) Antitheft slot : Attach a Kensington compatible security lock or antitheft

device.

Connecting a VGA, Mac Monitor or LCD/DLP Projector

Locate the RGB (VGA) input port of the display device and connect it to RGB OUTPUT port

of SPB370.

Make sure the Video Output switch is set to RGB.

RGB

OUTPUT

DC 12V VIDEO

OUTPUT

S-VIDEO

OUTPUT

DVI-I OUTP UT USB SD CARD

RGB cable

MAC

LCD/DLP projector

LCD monitor

MAC monitor

Monitor Adapter

(not supplied)

CRT monitor

5

Connecting a Monitor or LCD/DLP Projector with DVI

interface

Locate the DVI input port of the display device and connect it to DVI-I OUTPUT port of

SPB370.

Make sure the Video Output switch is set to RGB.

RGB

OUTPUT

DC 12V VIDEO

OUTPUT

S-VIDEO

OUTPUT

DVI-I OUTPU T USB SD CARD

LCD/DLP projector

with DVI interface

LCD Monitor

with DVI interface

DVI cable

(not supplied)

Connecting a TV

Locate the VIDEO (yellow), S-VIDEO or SCART RGB input port of the TV or Video

equipment (i.e., VCR) to record your presentation on a videotape and connect it to S-VIDEO

or VIDEO OUTPUT port of SPB370.

- Make sure the Video Output switch is set to TV.

- For better video quality, we strongly suggest using S-VIDEO connection.

RGB

OUTPUT

DC 12V VIDEO

OUTPUT

S-VIDEO

OUTPUT

DVI-I OUTPUT USB SD CARD

S-Video cable

S-Video to SCART cable

(not supplied)

S-VIDEO

RCA to SCART cable

(not supplied)

RCA cable

VIDEO

SCART

I N P U T

P r o j e c t o r

Te l e v i s i o n

V C R

6

Connecting the Power Adapter

Connect the power adapter to a standard 100V~240V AC power source.

RGB

OUTPUT

DC 12V VIDEO

OUTPUT

S-VIDEO

OUTPUT

DVI-I OUTPUT USB SD CARD

Power adapter

Power cord

Wall outlet

Connecting a Computer

Locate the RGB (VGA) output port of the computer or laptop to display your PC presentation

on screen and connect it to RGB IN 1 or RGB IN 2 ports of SPB370. The video signal from

the RGB INPUT port is streamed to RGB and DVI-I OUTPUT ports only, and displayed on

the screen even in stand-by mode. Press SOURCE button on the control panel or remote to

switch to PC-1 or PC-2.

IOIOI

RGB cable

Computer

Laptop

MAC

Monitor Adapter

(not supplied)

Connecting a Microphone

Plug a Ф 6.3mm jack Microphone to MIC IN port.

LIGHT BOXMIC IN VIDEO OUTPUT

SPB370

TV RGB

M i c r o p h o n e

( n o t s u p p l i e d )

7

Connecting to Audio Output Device

Locate the audio input port (red/white) of the Audio Output device and connect it to AUDIO

OUT port of SPB370. For computer, use an RCA Jack To 3.5mm Mono Plug Adapter and

connect it to Line-in port (blue) with this

symbol or Mic In port

.

IOIOI

RCA cable

AUDIO

I N PU T

T

e l e v i s i o n

V C R

S t e r e o

Desktop

Laptop

RCA Jack to 3.5mm

Mono Plug Adapter

(not supplied)

RCA cable

Connecting a Computer via USB Connection

Locate the USB port of the computer or laptop and connect it to USB port of SPB370. This

enables you to use SPB370 as a USB Camera and to transfer the captured images from the

memory source and to computer. Also see “Using AVerVision SPB370 as a Mass Storage”.

RGB

OUTPUT

DC 12V VIDEO

OUTPUT

S-VIDEO

OUTPUT

DVI-I OUTPUT USB SD CARD

USB cable

Computer

Laptop

MAC

8

Inserting and Ejecting a SD Card

Insert the card with the label facing up until it reaches the end. To remove, pull the card out.

The supported SD card capacity is from 16MB to 2GB. Make sure the card is formatted to

FAT16. SPB370 automatically creates and stores the images in AVERJPG folder.

S D c a r d

( n o t s u p p l i e d )

S

e

t

i

n

g

U

p

S

P

B

3

7

0

This section provides useful tips on how to adjust the SPB370 to meet your needs.

Arm

The arm must be unfolded fully in upright position.

LIGHT BOX

SPB350

VIDEO OUTPUT

TV RGB

90°

Correct Operating Position

LIGHT BOX

SPB350

RGB

SPB350

Wrong Operating Position

Camera Head

The camera head can be folded up 90° and turned 90° to the left and right. To display an

object more than 50cm away from the camera, unscrew the close-up lens. Do not forget to

screw back the close-up lens afterwards.

LIGHT BOX

SPB350

VIDEO OUTPUT

TV RGB

90°

9

0

°

9

0

°

50cm

9

Overhead Light

Press LAMP button on the control panel to turn on and off light.

90°

LIGHT BOXMIC IN VIDEO OUTPUT

SPB370

TV RGB

Infrared Sensor

Aim the remote control at the infrared sensors to operate the unit.

Light Box

Press LIGHT BOX button on the left panel of SPB370 to turn on and off light. Use this to

view negatives film, x-rays, and 35mm slides.

: DO NOT place an object weighing more than 8kg on top of the light box.

Light Box Button

negative film

photos

document

light weight object

8

K

g

(

+

)

Anti-glare

The anti-glare sheet is a special coated film that helps eliminate any glare that may be

encountered while displaying very shiny objects or glossy surfaces such as magazines and

pictures. To use, simply place the anti-glare sheet on top of the shiny document to reduce

reflected light.

10

Microscope Connection

Connecting the SPB370 to a microscope enables you to examine microscopic objects on a

big screen without straining your eyes.

Close-up Lens

1. Change the image display mode to

Microscope. Press MENU > select

SETTING > MODE > MICROSCOPE and

press ENTER.

2. Adjust the microscope focus to its best

clarity. Then, select the appropriate

adapter size that would fit the microscope

eyepiece.

3. Unscrew the close-up lens from the

camera head.

4. Remove the microscope eyepiece from

the microscope and connect it to the

microscope adapter. Then, fasten the 3

bolts until the adapter secures the

eyepiece.

We suggest using a microscope with

an eye relief of 15.5mm or higher for

better view.

5. Screw the microscope adapter to the

AVerVision camera head. Then, connect it

to the microscope.

Microscope

Adapter

(optional)

Microscope

Control Panel Light Color

The LED power button on the control panel of SPB370 indicates the status of the unit.

Color Description

Blue : The unit is in operating mode.

Orange : The unit is in standby mode.

U

s

i

n

g

W

e

b

B

r

o

w

s

e

r

t

o

C

o

n

t

r

o

l

S

P

B

3

7

0

This enables you to remotely control SPB370 thru any web browser (i.e. Microsoft Internet

Explorer). Make sure SPB370 is connected to an IP-based network.

To use web browser to control SPB370:

1. Use an RJ-45 Ethernet cable and connect it from the Ethernet port of SPB370 to RJ-45

wall jack or Ethernet hub.

ETHERNETRS-232RGB IN 1RGB IN 2AUDIO OUT

IOIOI

RJ-45 wall jack

RJ-45 Cable

(not supplied)

2. Set the IP, NETMASK and GATEWAY address of SPB370.

To set the network address:

Press MENU > select SETTING > ETHERNET and press ENTER. In the ETHERNET

menu, select DHCP and press

►

to turn DHCP ON to automatically request for network

address or OFF to manually set the network address.

11

To manually set the network address:

In the ETHERNET menu, use the

▲or▼ buttons

to make a

selection and to change value, press

► to enter or

to move

to the next digit, and press

ENTER to apply the new setting.

Make sure to set the correct address for each setting. For

assistance, contact your

network administrator.

ETHERNET

DHCP OFF

IP 010.001.004.016

NETMASK 000.000.000.000

GATEWAY 000.000.000.000

3. Type the IP address of SPB370 in the web browser. The Web browser will access the

embedded web server and can remotely control SPB370. To use the SPB370 remote

control interface, refer to section “Using the Infrared Remote Control”.

U

s

i

n

g

t

h

e

I

n

f

r

a

r

e

d

R

e

m

o

t

e

C

o

n

t

r

o

l

Use the SPB370 Remote Control to enhance your presentation by having the ability to switch

between three (3) presentation modes and access various features. To use the remote

control, first insert the batteries (2 “AAA” size batteries are provided) into the battery

compartment at the back of the remote. Use the figure and descriptions below as a reference

for remote control functions.

Name Function

(1) POWER Turn the unit on/off.

(2) LASER Turn on the laser pointer.

DO NOT look directly at the laser pointer and avoid

aiming the laser at any surface that may reflect the

beam (i.e., a mirror or mirrored surface).

(1)

(5)

(8)

(12 )

(17

)

(16

)

(15

)

(14

)

(13

)

(2)

(10 )

(7)

(6)

(3)

(4)

(9)

(11)

(3) Shuttle

Wheel

- Turn the shuttle wheel clockwise to

zoom in and counter-clockwise to zoom

out the image optically and digitally in

Camera and Playback mode only.

When it exceeds the maximum optical

zoom level of about 8X, you may still

continue to AVEROPTICAL zoom up to

2.5X AVerZoom and 8X digitally zoom.

Press ENTER to return to normal view

(100%). The zoom bar indicator will turn

from blue to aqua to indicate that you

can pan around the image.

- Press the shuttle wheel ▲,▼,◄, & ► to

pan the image while in digital zoom

mode, to make a selection on 16-

thumbnail images or move to the next or

previous single full screen preview in

Playback mode, or to make a selection

or adjustment on the OSD main-menu

and sub-menu (See Menu Functions for

more details).

12

Name Function

(4) ENTER Make a selection in Playback mode and OSD menu. Use this to quick zoom

to 200% or back to 100% in Camera mode only.

(5) AF (Auto Focus) Adjust the focus automatically.

(6) Source Switch between Camera, Playback, PC mode.

- Camera mode displays the video signal from the built-in camera.

- Playback mode displays the captured image from the memory source in

16-thumbnail images. Use ▲,▼,◄, & ► buttons or rotate the shuttle

wheel to make a selection and ENTER to display the selected image in full

screen.

Press MENU to display the Playback menu. Select SLIDE SHOW to start

or set the time interval between frames in second, MEMORY SOURCE to

select the image location between the built-in memory or SD card, and

DELETE to permanently remove the selected image from the selected

memory source.

- PC mode displays the video signal from the RGB IN 1 and RGB IN 2 port

of SPB370. It will first display the signal from RGB IN 1. To display the

signal from RGB IN 2, press the SOURCE button again. The PC LED light

will remain on when it is in PC 1 and PC2.

(7) CAP/DEL - Capture a still image in Camera mode. The captured image is saved in the

selected memory source at 1600 x 1200 resolution and the built-in memory

can store up to 80 images.

- Remove the selected picture from the selected memory source

permanently in Playback mode.

(8) ROTATE Turn the image by 90°in Camera mode and 180 in full screen Playback mode.

(9) TIMER Display the OSD timer menu and use ▲or▼ buttons to select SET TIME to

set the time value, START to begin the countdown timer, PAUSE/RESUME

to temporarily halt or continue, and STOP to end. Press MENU to hide the

timer menu.

(10) PROFILE Recall and switch from the 3 saved user setting profile selections (See MENU

Functions – SAVE for more details).

(11) PIP Display/hide a thumbnail of the captured image from the memory source at

the corner of the screen while in Camera mode.

Use ◄ or ► buttons to move to the previous or next image and ENTER to

display the image in full screen. To move the mini playback screen to different

corners, press MENU, go to PIP and select the position of the mini playback

screen.

(12) PRESENTER Select to turn on/off AVerBox or AVerVisor. Only one feature can be used at

a time.

AVerBox overlays a frame on the presentation

screen. Selecting SHADE changes the opacity of

the area outside the box from 0%, 50% and 100%,

COLOR to change the frame color from red, green

and blue, and RESIZE to change the size of the

frame. To resize or move the frame around the

presentation screen, press the shuttle wheel

▲,▼,◄, & ►.

AVerVisor covers part of the presentation

screen. The upper part of the presentation

screen is slightly exposed when it is being

called each time. To expose part of the covered

area, press the shuttle wheel ▲,▼,◄, &►.

Select SHADE to change the darkness of the

shaded area between 50% or 100%.

(13) MENU Pull up and exit the OSD main-menu and sub-menu.

(14) AUTO IMAGE Automatically adjust and set the white balance and exposure setting.

(15) FREEZE Toggle to pause or resume the camera.

13

Name Function

(16) EFFECT Convert and display the image in BW, Negative or Color in Camera and

Playback mode only.

(17) SPLIT SCRN Turn on/off split screen mode. Split Screen divides the screen into two parts.

One side displays the live image from the SPB370 camera and the other side

displays the captured images from the memory source in 8-thumbnail

preview.

Use the ▲,▼,◄, &► buttons to make a selection and ENTER to enlarge the

selected image in split screen mode. To horizontally or vertically pan the

enlarged image, use the ◄ & ► or ▲&▼ buttons. To switch to different split

screen type, press MENU, go to SPLIT SCREEN and select between vertical

or horizontal splitting type.

T

o

u

c

h

B

u

t

o

n

C

o

n

t

r

o

l

P

a

n

e

l

The touch button control panel located on the top side of AVerVision SPB370 provides quick

access to commonly used functions.

TV

RGB

SOURCE

POWER

PLAYBACK

CAMERA

PC

MENU

FREEZE

AUTO FOCUS

AUTO IMAGE

ROTATE

CAP/DEL

BRIGHTNESSLAMP

(2

)

(1

)

(13) (12) (11)

(3

)

(6

)

(5

)

(7

)

(4

)

(10 ) (9)

(8

)

(14)

Name Function

(1) POWER Turn the unit on/off.

(2) SOURCE Switch between Camera, Playback, PC mode.

- Camera mode displays the video signal from the built-in camera.

- Playback mode displays the captured image from the memory

source in 16-thumbnail images. Use ▲,▼,◄, & ► buttons or

rotate the shuttle wheel to make a selection and ENTER to display

the selected image in full screen.

Press MENU to display the Playback menu. Select SLIDE SHOW

to start or set the time interval between frames in second,

MEMORY SOURCE to select the image location between the

built-in memory or SD card, and DELETE to permanently remove

the selected image from the selected memory source.

- PC mode displays the video signal from the RGB IN 1 and RGB IN

2 port of SPB370. It will first display the signal from RGB IN 1. To

display the signal from RGB IN 2, press the SOURCE button

again. The PC LED light will remain on when it is in PC 1 and PC2.

(3) MENU Pull up and exit the OSD main-menu and sub-menu.

(4) ENTER Make a selection in Playback mode and OSD menu.

(5) AUTO IMAGE Automatically adjust and set the white balance and exposure setting.

(6) FREEZE Toggle to pause or resume the camera.

(7) CAP/DEL - Capture a still image in Camera mode. The captured image is

saved in the selected memory source at 1600 x 1200 resolution

and the built-in memory can store up to 80 images.

- Remove the selected picture from the selected memory source

permanently in Playback mode.

14

Name Function

(8) ROTATE Turn the image by 90°in Camera mode and 180 in full screen

Playback mode.

(9) BRIGHTNESS Adjust the brightness level in Camera mode to improve the visibility.

(10) AUTO FOCUS Adjust the focus automatically.

(11) SHUTTLE

WHEEL

- Turn the shuttle wheel clockwise to zoom in and counter-clockwise

to zoom out the image optically and digitally in Camera and

Playback mode only.

When it exceeds the maximum optical zoom level of about 8X, you

may still continue to AVEROPTICAL zoom up to 2.5X AVerZoom

and 8X digitally zoom. Press ENTER to return to normal view

(100%). The zoom bar indicator will turn from blue to aqua to

indicate that you can pan around the image.

- Press the shuttle wheel ▲,▼,◄, & ► to pan the image while in

digital zoom mode, to make a selection on 16-thumbnail images or

move to the next or previous single full screen preview in Playback

mode, or to make a selection or adjustment on the OSD main-

menu and sub-menu (See Menu Functions for more details).

(12) LAMP Turn the overhead light on/off.

(13) Source LED

Indicator

Indicate the selected Source mode either in Camera, Playback or

PC.

(14) Video Output

LED Indicator

Indicate the setting of the Video Output switch to which the video

signal is being sent out.

U

s

i

n

g

A

V

e

r

V

i

s

i

o

n

S

P

B

3

7

0

a

s

a

M

a

s

S

t

o

r

a

g

e

This enables you to transfer the captured image to and from the memory source and PC.

You MUST read and follow the instructions below BEFORE connecting the USB

cable.

Every time when using the SPB370 as Mass Storage, the following MUST be done:

1. Select the memory source.

To select the memory source, press MENU >

select SETTING > MEMORY > SOURCE >

EMBEDDED or SD and press ENTER; then

press MENU to exit.

2. MUST set the USB CONNECTION as MASS

STORAGE.

To set the USB connection type, press MENU >

select SETTING > USB CONNECTION > MASS

STORAGE and press ENTER; then press

MENU to exit.

3. When “MASS STORAGE” appears at the

lower left corner of the presentation screen,

you may now connect the USB cable (See

“Connecting a Computer via USB Connection”

for illustration).

4. Upon connecting the USB cable, the system automatically detects the new removable

disk.

5. In the Removable Disk dialog box, select Open folder to view files and then click OK.

You may now transfer the file to and from your PC hard disk.

15

O

S

D

N

a

v

i

g

a

t

i

o

n

T

r

e

VIDEO OUTPUT OSD

For TV output, RESOLUTION is not included in the menu list.

PLAYBACK OSD

MENU

SLIDE SHOW

MEMORY SOURCE

DELETE

NO

YES

EMBEDDED

SD CARD

START

INTERVAL

SLIDE SHOW

1011

16

M

e

n

u

F

u

n

c

t

i

o

n

s

The MENU functions of SPB370 enhance fine-tuning your screen display, set the timer,

select OSD language and more. Press the MENU button to call up and exit from the main

menu or sub-menu display. Then use ▲or▼ buttons to select the items in the menu list.

Use ►/ENTER button to enter sub-menu and ◄/ ENTER to return to main menu. To

adjust the setting, press ◄or► buttons. To make a selection, press ENTER.

OSD Menu Description

MENU

EFFECT

MIRROR

PRESENTER

SPLIT SCREEN

PIP

SETTING

TIMER

CAPTURE

RECALL

DEFAULT

COLOR

B / W

NEGATIVE

EFFECT

Press ► and use ▲or▼ buttons to select and display the image in

Camera mode into positive (true color), monochrome (black and white) or

negative. Then press ►/ENTER to make a selection.

MENU

EFFECT

MIRROR

PRESENTER

SPLIT SCREEN

PIP

SETTING

TIMER

CAPTURE

RECALL

DEFAULT

ON

OFF

MIRROR

Press ► and use ▲or▼ buttons to select turning on/off MIRROR to flip

the image in Camera mode. Then press ►/ENTER to make a selection.

MENU

EFFECT

MIRROR

PRESENTER

SPLIT SCREEN

PIP

SETTING

TIMER

CAPTURE

RECALL

DEFAULT

AVERBOX OFF

AVERVISOR OFF

SHADE

COLOR

RESIZE

PRESENTER

Press ► and use ▲or▼ buttons to select and turn on either AVERBOX or

AVERVISOR. Then press ►/ENTER to make a selection. Only one

feature can be used at a time.

AVerBox overlays a frame on the presentation screen. Selecting SHADE

changes the opacity of the area outside the box from 0%, 50% and 100%,

COLOR to change the frame color from red, green and blue, and RESIZE

to change the size of the frame. To resize or move the frame around the

presentation screen, press the shuttle wheel ▲,▼,◄, & ►.

AVerVisor covers part of the presentation screen. The upper part of the

presentation screen is slightly exposed when it is being called each time.

To expose part of the covered area, press the shuttle wheel ▲,▼,◄, & ►.

Select SHADE to change the darkness of the shaded area between 50%

or 100%.

MENU

EFFECT

MIRROR

PRESENTER

SPLIT SCREEN

PIP

SETTING

TIMER

CAPTURE

RECALL

DEFAULT

VERTICAL

HORIZONTAL

SPLIT SCREEN

Press ► and use ▲or▼ buttons to select dividing the screen either

vertically or horizontally. Then press ►/ENTER to make a selection.

This function divides the screen into two parts. One side displays the live

image from the SPB370 camera and the other side displays the captured

images from the memory source in 8-thumbnail preview.

Use the ▲,▼,◄, &► buttons to make a selection and ENTER to enlarge

the selected image in split screen mode. To horizontally or vertically pan

the enlarged image, use the ◄ & ► or ▲or▼ buttons.

Page is loading ...

AVer AVerVision SPB370 User manual

This manual is also suitable for

AVer AVerVision SPB370 User manual

Related papers

Other documents